BB-4WSD9R [ETC]
2-4 WIRE 422/485 9PIN CONV.;型号: | BB-4WSD9R |
厂家: | ETC |
描述: | 2-4 WIRE 422/485 9PIN CONV. |
文件: | 总2页 (文件大小:434K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Port Powered RS-232/485
Converters
Models 4WSD9R, 4WSD9TB
www.advantech-bb.com
PRODUCT FEATURES
•
•
•
•
•
•
Change RS-232 TD and RD to RS-485 signals
Extend RS-232 data signals up to 1.2 km (4,000 ft.)
Automatic Send Data Control
Baud rates up to 115.2 kbps
RS-232 port power or external 12 VDC power jack
Dipswitch selectable RS-422 or RS-485
Models 4WSD9TB and 4WSD9R, universal serial converters, provide RS-232
to RS-422/RS-485 conversion using either port-power or an external power
supply. Model 4WSD9TB has a terminal block RS-485 connector; Model
4WSD9R has a DB9 female RS-485 connector.
ORDERING INFORMATION
RS-232
OPTIONAL
POWER
MODEL
RS-485
CONNECTOR
(DCE)
OUTPUT
NUMBER
4WSD9R
4WSD9TB
CONNECTOR
SUPPLY
RS-485 2 or 4-wire
or RS-422
✔
✔
DB9 Female
DB9 Female
Data is converted in both directions, RS-232 Transmit Data is converted to
balanced RS-422 or RS-485 Transmit Data. Received RS-422/485 signals are
converted to RS-232. Unlike converters which require programming hardware
handshaking signals to control RS-422 or RS-485 operation, Models 4WSD9TB
and 4WSD9R provide automatic Send Data Control. In RS-485 mode, the
RS-485 driver is enabled by circuitry which senses the RS-232 TD input. In
half-duplex RS-485 mode, the receiver is enabled when not transmitting. For
full-duplex operation, the receiver is set always enabled.
RS-485 2 or 4-wire
DB9 Female Terminal Block
or RS-422
ACCESSORIES
SMI6-12-V-P230-C1 - Power Supply, 12 VDC 6 Watt, 2.5MM Plug, International AC
Input, International AC Blades
9PAMF6 - DB9 male to DB9 female adapter cable, 1.8 m (6 ft.)
In RS-422 mode, the transmitter and receiver are always enabled. The
operating mode is set with 4 switches see Table 1. The converters are
powered by the RS-232 signal lines whether they are set high or low. If not
enough power is available from the port, or no handshaking lines are available,
a DC jack is provided to connect an external 12VDC supply. The DB9 female
connector for RS-232 is wired as DCE (like a modem).
The RS-232 port has a female DB9 connector with pins 2 (RD), 3 (TD), and 5
(Signal Ground) supported. Pins 7 (RTS) and 8 (CTS) are tied together, and pins
6 (DSR), 1 (DCD), and 4 (DTR) are also tied together. Any incoming data lines
in either the high or low state are used to port power the converter. The more
handshake lines available, the more likely the unit can be port powered. Table 2.
shows the RS-232 pinout.
Table 1. RS-422/485 PINOUT
Table 2. RS-232 PINOUT
PIN #
SIGNAL
RD (A)-
TD (B) +
GND
2
3
4
6
7
8
PIN #
SIGNAL
DCD
RD
1
2
3
4
5
6
7
8
GND
TD
RD (B)+
TD (A)-
DTR
GND
DSR
RTS
CTS
No external power is required if two RS-232 output handshake lines are
available and the cable run is short. If the handshake lines are raised and no
termination is used, the power efficiency is greatly increased. Less than 3 mA
is required to operate the converter - plus the load current. For applications
that do not have handshake lines or require a large load current, power may
be externally supplied with a +12 VDC power supply with a 2.5mm plug (tip
positive).
Although handshake lines can be used to power the converter, no handshaking
is required to control the RS-422/RS-485 driver. With Switch 1 set to RS-422, the
driver is always enabled. When Switch 1 is in the RS-485 position, the RS-485
driver is automatically enabled during each spacing state on the RS-232 side.
During the marking or idle state, the RS-485 driver is disabled and the data lines
are held in the marking state by the 4.7K Ohm pull-up and pull-down resistors.
The value of these resistors may need to be changed to a different value when
termination is used in order to maintain the proper DC bias during the idle state.
All product specifications are subject to change without notice.
4WSD9R_4WSD9TB_3417ds
orders@advantech-bb.com
support@advantech-bb.com
Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104
European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445
Port Powered RS-232/485
Converters
Models 4WSD9R, 4WSD9TB
SPECIFICATIONS
SERIAL TECHNOLOGY
Data Rate
RS-232
MECHANICAL
Dimensions,
Enclosure
4WSD9R: 7.8 x 4.3 x 2.0 cm (3.0 x 1.6 x 0.8 in)
4WSD9TB: 9.0 x 4.3 x 2.3 cm (3.6 x 1.7 x 0.9 in)
Plastic, Inline
4WSD9R: 49 g (0.10 lbs.)
4WSD9TB: 50 g (0.11 lbs.)
4WSD9R: 880179
4WSD9TB: 345242
Parts Count Reliability Prediction
115.2 kbps maximum
4WSD9R: DB9 female
4WSD9TB: DB9 female
RD, TD, GND supported.
Pins 7 (RTS) and 8 (CTS) are tied together.
Pins 6 (DSR), 1 (DCD), and 4 (DTR) are tied together.
Connector
Weight
Signals /
Port Power *
MTBF
MTBF Calc. Method
ENVIRONMENTAL
Operating Temperature
Storage Temperature
Operating Humidity
RS-422/485
4WSD9R: DB9 female
4WSD9TB: Terminal block
4.7k Ohms
Connector
0 to +70 °C (+32 to +158 °F)
-40 to +85 °C (-40 to +185 °F)
0 - 95% Non-condensing
Biasing Resistors
Signals TDA (-), TDB (+), RDA (-), RDB (+), GND
Termination
Operation
None
DECLARATION OF CONFORMITY - 4WSD9R
FCC, CE
Dipswitch selectable RS-422 or RS-485
4WSD9R: RS-485 2 or 4-wire or RS-422
4WSD9TB: RS-485 2 or 4-wire or RS-422
2014/30/EC - Electromagnetic Compatibility Directive
2011/65/EU - Reduction of Hazardous Substances Directive
(RoHS)
Directives
POWER
Port-powered: from RS-232 handshake lines.
External 12 VDC power supply, optional.
Port-powering requires 7 to 12 VDC supplied on at least
one handshake line.
2.5 mm plug (tip positive)
12 VDC
2012/19/EU - Waste Electrical and Electronic Equipment (WEEE)
EN55032 - Information Technology Equipment - Class B RF
Emissions
EN55024 - Information Technology Equipment - Immunity (Light-
Industrial Environments)
Source
* Port-Power
EMC Standards
Power Connector
Input Voltage
DECLARATION OF CONFORMITY - 4WSD9TB
FCC, CE
2014/30/EC - Electromagnetic Compatibility Directive
2011/65/EU - Reduction of Hazardous Substances Directive
(RoHS)
Directives
2012/19/EU - Waste Electrical and Electronic Equipment (WEEE)
EN55022:2010+AC - Information Technology Equipment - Class B
RF Emissions
EN55024 - Information Technology Equipment - Immunity (Light-
Industrial Environments)
EN61000-4-2 - ESD Immunity
EMC Standards
EN61000-4-3 - Radiated Immunity
EN61000-4-4 - EFT/Burst Immunity
EN61000-4-6 - RF Conducted Immunity
orders@advantech-bb.com
support@advantech-bb.com
Corporate Headquarters: 707 Dayton Road, PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104
European Office: Westlink Commercial Park, Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445
相关型号:
BB-5221T
Flag Avikrimp™ Quick Disconnect, Female, for 14-16 (2.00-1.30) Wire, Mylar TapeTab 6.35mm (.250") x 0.81mm (.032"
MOLEX
BB-5221Z
Flag Avikrimp™ Quick Disconnect, Female, for 14-16 (2.00-1.30) Wire, Metal Strip, Tab6.35mm (.250") x 0.81mm (.032
MOLEX
BB-5224
Avikrimp™ Quick Disconnect for 14-16 AWG Wire, Female Flag, Tab 4.75mm (.187") x0.51mm (.020")
MOLEX
BB-5225
Flag Avikrimp™ Quick Disconnect, Female, for 14-16 (2.00-1.30) Wire, Box, Tab4.75mm (.187") x 0.81mm (.032")
MOLEX
BB-5225T
Flag Avikrimp™ Quick Disconnect, Female, for 14-16 (2.00-1.30) Wire, Mylar TapeTab 4.75mm (.187") x 0.81mm (.032"
MOLEX
©2020 ICPDF网 联系我们和版权申明