BUS-63102-200Y [ETC]
Transceiver ; 收发器\n型号: | BUS-63102-200Y |
厂家: | ETC |
描述: | Transceiver
|
文件: | 总16页 (文件大小:125K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
BUS -6 3 1 0 0 S ERIES
MIL-S TD-1 5 5 3 DATA BUS
S INGLE AND DUAL TRANS CEIVERS
BUS-63102
BUS-63105
BUS-63125
FEATURES
DESCRIPTION
The BUS-63100 transceivers are internally fixed or externally set
complete transmitter and receiver threshold level. An external STROBE
pairs conforming fully to MIL-STD- input enables or disables the receiver
1553A and 1553B. Features available outputs.
• Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
•
with selected models of this high reli-
The transmitter section accepts bipo-
ability series include: Smiths and
lar TTL signal data at its TX Data and
Harris interface type choices,
Model Capabilities:
Single or Dual Redundant
Packaging
•
TX Data input lines and produces
+12 V/+15 V power supply voltage
phase modulated bipolar data at the
range, variable threshold levels, and
TX Data and TX Data outputs. The
single (24-pin DDIP or square) and
-12 V/-15 V Power Supply Voltage
Range Available
transmitters’ output voltage level is
completely independent dual redun-
typically 28 Vpp to 30 Vpp. An exter-
dant (36-pin DDIP) packaging config-
nal input, INHIBIT, takes priority over
urations. All models are also available
Harris or Smith’s I/O Compatibility
the transmitter inputs and disables
in flat packs.
the transmitter when activated with a
logic “1.”
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
•
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
Low Power
•
High Reliability – LSI
•
±V
+5 V
RECEIVER STROBE
1553
DATA
BUS
BI PHASE
TTL DATA
RECEIVER SECTION
PHASE MODULATED
BIPOLAR DATA
COMPARATOR
RX Data
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
DECODER
RX Data
FILTER
LIMITER
RX Data In
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
TX Data Out
TX Data In
TX Data In
SHAPING
NETWORK
DRIVER
ENCODER
SHAPING
NETWORK
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
ENCODER/DECODER COMPATIBILITY
GENERAL
BUS-63105, BUS-63107, BUS-63125 and BUS-63127 are
directly compatible to Harris 15530 type Encoder/Decoders. All
other transceivers are directly compatible to Smiths type.
Transceivers which are directly comparible with one type can be
converted for use with the other by simply switching the output
lines, RX Data and RX Data, and inverting their signals by
means of external inverting gates.
The BUS-63100 Series offers complete transmitter and receiver
pairs packaged in either single or dual redundant form which are
designed for use in any MIL-STD-1553 application.
Figure 1 shows a BUS-63100 Series transceiver connected to a
MIL-STD 1553 Data Bus. Once transformer isolated, coupling to
a MIL-STD-1553 Data Bus can be either short stub (direct) or
long (transformer). Figure 2 shows the different configurations
and lists the recommended DDC transformer bus product for use
with each model.
WAVEFORMS
All transceivers conform fully to MIL-STD-1553 requirements.
Additionally, BUS-63102 conforms to MACAIR standards, pro-
ducing sinusoidal waveforms at 1 MHz.
TRANSCEIVER CAPABILITIES
DDC’s BUS-63100 Series of transceivers offer a wide range of
capabilities (on selected models), which include power supply
voltage levels, packaging configurations, Smiths or Harris type
encode/decoder direct compatibility, and internal (pre-set)
and/or external (adjustable) threshold levels. The capabilities of
the different models are described in the paragraphs which fol-
low and are summarized in TABLE 1.
THRESHOLD LEVELS
All models offer internal (factory preset) threshold levels.
Additionally, BUS-63102 and BUS-63104 offer externally set
threshold levels. These external threshold levels are adjustable
from 0 V to 2 V, with the use of two external 10 KOhm poten-
tiometers; see FIGURE 5.
POWER SUPPLY VOLTAGES
Power supply voltage requirements on the BUS-63102 and
BUS-63104 are met over a range from ±12 V to ±15 V. All mod-
els operate with either -12 V or -15 V supplies. All models
require a + 5 V supply. Refer to TABLE 1.
TABLE 2. TRANSMIT OPERATING MODE
DRIVER OUTPUT(2)
TX Data In TX Data In
TX INHIBUIT
X(1)
0
OFF(3)
OFF
ON
X
0
1
0
1
H
X
L
PACKAGING CONFIGURATIONS
0
Single transceivers, BUS-63102 and BUS-63104 are packaged
in 24 pin square packages, all other single transceivers are
packaged in 24 pin DDIP. Dual transceivers are packaged in 36
pin DDIP’s.
1
L
ON
1
X
OFF
NOTES:
(1) X = Don’t Care
(2) DRIVER OUT = TX Data Out and TX Data Out.
(3) DRIVER OUTPUT terminals are in the high impedance mode
during OFF time, independent of INHIBIT status.
TABLE 1. TRANSCEIVER CAPABILITIES
±12 VDC
TO
±15 VDC
24 PIN
SQUAR
E
I/O COMPATIBUILITY THRESHOLD
-12
VDC
-15
VDC
24 PIN
DDIP
36 PIN
DDIP
MIL-STD- FLATPACK
MACAIR
•
1553
MODEL NO.
SMITHS
HARRIS
INT
•
EXT
Single
BUS-63102
Single
BUS-63112
•
•
•
•
•
•
•
•
•
BUS-63104
BUS-63105
BUS-63107
BUS-63115
BUS-63117
•
•
•
•
•
•
•
•
•
•
BUS-63114
BUS-63106
BUS-63108
BUS-63116
BUS-63118
•
•
•
•
•
•
•
•
•
•
•
•
Dual
BUS-63125
Dual
BUS-63126
•
•
•
•
•
•
•
BUS-63127
BUS-63135
BUS-63137
•
•
•
•
•
•
•
•
•
•
•
BUS-63128
BUS-63136
BUS-63138
•
•
2
Z (70Ω, NOM)
0
DATA
BUS
SHORT STUB
(DIRECT COUPLED)
1 FT MAX
(1.4:1)
55Ω
55Ω
8
1
2
3
TX
BUS-63105
4
TX
RX
RX
BUS-63115
BUS-63125(1)
BUS-63135(1)
39VPP
28VPP
BUS-25679
LONG STUB
(TRANSFORMER
COUPLED)
OR
(1:1.4)
(2:1)
20 FT MAX
52.5Ω
52.5Ω
1
2
3
7
5
8
4
1
3
20 VPP
BUS-25679
BUS-25679
SHORT STUB
(DIRECT COUPLED)
(1:1)
1 FT MAX
55Ω
55Ω
1
2
3
8
4
TX
TX
BUS-63102
BUS-63104
30VPP(BUS-63102)
28VPP(BUS-63104
RX
RX
BUS-27765
LONG STUB
(TRANSFORMER
COUPLED)
(1:0.7)
OR
(1:1.4)
20 FT MAX
52.5Ω
52.5Ω
1
7
5
8
4
1
3
2
3
BUS-25679
BUS-27765
21 VPP (BUS-63102)
20VPP(BUS-63104)
SHORT STUB
(DIRECT COUPLED)
(1:0.83)
1 FT MAX
55Ω
55Ω
8
4
1
2
3
TX
TX
BUS-63107
BUS-63117
BUS-63127(1)
BUS-63137(1)
33VPP
28VPP
RX
RX
BUS-29854
LONG STUB
(TRANSFORMER
(1:0.6)
(1:1.4)
COUPLED)
OR
20 FT MAX
52.5Ω
52.5Ω
1
2
3
7
5
8
4
1
3
20VPP
BUS-29854
BUS-25679
Z (70Ω, NOM)
Notes:
0
(1) One half of dual transceivers shown.
(2) Bus must be terminated with its characteristic impedance at both ends.
(3) Only one connection can be made from the Transceiver to the MIL-STD
Data Bus, either long stub or short but not both.
FIGURE 2. BUS COUPLING CONFIGURATIONS
3
TABLE 3. BUS-63100 SERIES SPECIFICATIONS
BUS-63102(1)
BUS-63112
Single
BUS-63104
BUS-63114
Single
BUS-63105†
BUS-63112
Single
BUS-63104
BUS-63114
Single
TRANSCEIVER NUMBER
CHANNELS
POWER SUPPLIES
ENCODER/DECODER INTERFACE TYPE
MATCHING TRANSFORMER MODEL
±12 VDC to ±15 VDC
Smiths
BUS-27765
±12 VDC to ±15 VDC -15 VDC
-15 VDC
Smiths
BUS-25679
Smiths
Harris
BUS-27765
BUS-25679
RECEIVER
Strobe
Input Level
1 ‘LS Load
*
1 TTL
*
*
*
40 Vpk-pk, Diff. max
0.5 Vpk-pk min, 1.0 Vpk-pk max
40 db, min
7 kOhm, min
5 pf, max
*
*
*
*
*
*
*
Threshold Level (Internal)(2)(3)
CMRR
Input Resistance-Diff.
Input Capacitance-Diff.
Output Fan Out
0.56 Vpk-pk min, 1.0 Vpk-pk max
*
*
*
*
*
*
*
*
10 TTL Loads
TRANSMITTER
TX Inhibit
1 ‘LS Load
*
1 TTL
*
Input Level
1 ‘LS Load
*
*
*
1 TTL
*
*
Output Level(Direct Coupled)(4)
29 Vpk-pk, nom
across 140 Ohm load
280 ns, typ
10 mVpk-pk, Diff. max
±90 mVpk-pk, max across
35 Ohm load
*
*
*
*
*
*
*
150 ns, typ
125 ns, typ
Rise/Fall Time
Output Noise
Output Offset Voltage
*
*
*
*
*
*
Output Impedance-Non-Transmitting
Output Resistance- Diff.
Output Capacitance-Diff.
10 kOhm, min
5 pF, max
*
*
*
*
*
*
LOGIC
TTL/CMOS Compatible
All Inputs
All Outputs
2’ LS Loads, max
10 TTL Loads, max
*
*
1 TTL
*
*
*
POWER SUPPLY REQUIREMENTS
+12 VDC
-12 VDC
+5 VDC ±10% to +15 VDC ±5% to -15 VDC ±5% +5 VDC ±10%
-15 VDC ±5%
30/45 mA
30/45 mA
30/45 mA
24/30 mA
85/114 mA
140/180 mA
51/65 mA
118/135 mA
175/195 mA
30/45 mA
30/45 mA
30/45 mA
20/30 mA
95/130 mA
170/225 mA
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
THERMAL
Operating Junction Temperature
Operating Case Temperature
Storage Temperature
Thermal Inpedance
Junction to Case
-55°C to +160°C
-55°C to +125°C
-65°C to +150°C
*
*
*
*
*
*
*
*
*
40°C/W (Hottest Die)
21°C/W (24 Pin Square)
*
*
7.0°C/W
30°C/W (24 Pin DDIP)
Case to Air (typ)
*
POWER DISSIPATION
Single Channel Transmitting
12 V Supply
15 V Supply
15 V Supply
*
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
1.05/1.37 W
1.86/2.49 W
2.48/3.28 W
1.28/1.58 W
2.47/3.24 W
3.43/4.40 W
0.45/0.68 W
0.85/1.45 W
1.30/2.23 W
*
*
*
POWER DISSIPATION
Hottest Die(5)
12 V Supply
15 V Supply
15 V Supply
*
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
0.0 W
0.12/0.15 W
0.24/0.29W
0.0 W
0.15/0.18 W
0.30/0.36 W
0.45/0.68 W
0.85/1.45 W
1.30/2.23 W
*
*
*
MECHANICAL
Package Style
Dimensions
24 Pin Square
1.258” x 1.258” x 0.175”
*
*
*
*
*
*
*
*
24 Pin DDIP
*
*
*
1.400” x 0.805” x 0.200”
35.56 mm x 20.32 mm x 5.08 x mm
24 Pin Square Flat Pack
1.275” x 0.775” x 0.175”
32.36 mm x 19.69 mm x 4.45 x mm
0.6 oz
31.95 mm x 31.95 mm x 4.45 x mm
24 Pin Square Flat Pack
1.255” x 1.255” x 0.160”
31.88 mm x 31.88 mm x 4.06 x mm
0.6 oz
Package Style
Dimensions
*
*
*
*
Weight
17 (g)
17 (g)
*
4
NOTES for TABLE 3.
(1) On BUS-63102, filtering eliminates harmonics above 1 MHz. Differential group delay is ± 35 ns (10 kHz-2 MHz).
(2) The Threshold Level, as referred to in this specification, is meant to be the maximum peak-to-peak voltage
(measured on the Data Bus) that can be applied to the receivers’ input without causing the output to change
from the OFF state.
BUS-63107
BUS-63108
Single
BUS-63117
BUS-63118
Single
(3) On BUS-63102 and BUS-63104, external threshold levels are adjustable from 0V to 2V, with two external 10K Ohm
potentiometers. Connect one pot between pin 5 and GND and the other between pin 12 and GND.
(4) On BUS-63102, Output Level (direct coupled) is 30 V pk-pk.
(5) On BUS-63102 and BUS-63104, Hottest Die are defined as the driver transistors.
* Same as value to the left.
-12 VDC
Harris
BUS-29854
-12 VDC
Smiths
BUS-29854
† BUS-63105 available as Military (DESC) drawing 5962-86049-02ZC
†† BUS-63125 and BUS-63126 are available as Military (DESC) drawing 5962-87579.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
115 ns, typ
*
*
*
*
*
*
*
*
*
*
*
+5 VDC ±10%
-12 VDC ±5%
30/45 mA
30/45 mA
30/45 mA
20/30 mA
115/155 mA
210/275 mA
*
*
*
*
*
*
*
*
30°C/W (24 Pin DDIP)
*
12 V Supply
*
0.39/0.59 W
0.81/1.36 W
1.30/2.16 W
*
*
*
12 V Supply
*
0.39/0.59 W
0.81/1.36 W
1.30/2.16 W
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
5
TABLE 3. BUS-63100 SERIES SPECIFICATIONS (CONTINUED)
BUS-63125 ††
BUS-63126 ††
Dual
-15 VDC
Harris
TRANSCEIVER NUMBER
BUS-63135
BUS-63136
Dual
-15 VDC
Smiths
BUS-63127
BUS-63128
Dual
-12 VDC
Harris
CHANNELS
POWER SUPPLIES
ENCODER/DECODER INTERFACE TYPE
MATCHING TRANSFORMER MODEL
BUS-25679
BUS-29854
BUS-25679
RECEIVER
Strobe
Input Level
1 ‘LS
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Threshold Level (Internal)(2)(3)
CMRR
Input Resistance-Diff.
Input Capacitance-Diff.
Output Fan Out
TRANSMITTER
TX Inhibit
Input Level
Output Level(Direct Coupled)(4)
1 ‘LS
1 ‘LS
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
150 ns, typ
Rise/Fall Time
Output Noise
Output Offset Voltage
*
*
*
Output Impedance-Non-Transmitting
Output Resistance- Diff.
Output Capacitance-Diff.
*
*
*
*
*
*
LOGIC
TTL/CMOS Compatible
All Inputs
All Outputs
2 ’LS
*
*
*
*
*
POWER SUPPLY REQUIREMENTS
(Total Hybrid)
+5 VDC ±10%
(Total Hybrid)
(Total Hybrid)
-15 VDC ±5%
+5 VDC ±10% -15 VDC ±5% +5 VDC ±10% -12 VDC ±5%
60/90 mA
60/90 mA
60/90 mA
40/60 mA
115/160 mA
190/255 mA
60/90 mA
60/90 mA
60/90 mA
40/60 mA
115/160 mA
190/255 mA
60/90 mA
60/90 mA
60/90 mA
40/60 mA
135/185 mA
230/305 mA
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
THERMAL
Operating Junction Temperature
Operating Case Temperature
Storage Temperature
Thermal Inpedance
Junction to Case
*
*
*
*
*
*
*
*
*
7.0°C/W
20°C/W (36 Pin DDIP)
*
*
*
*
Case to Air (typ)
POWER DISSIPATION
(Total Hybrid,
(Total Hybrid,
(Total Hybrid,
Single Channel Transmitting
One Channel Transmitting)
One Channel Transmitting)
One Channel Transmitting)
0.90/1.35 W
1.30/2.13 W
1.75/2.91 W
0.90/1.35 W
1.30/2.13 W
1.75/2.91 W
0.78/1.18 W
1.20/1.95 W
1.69/2.75 W
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
POWER DISSIPATION
Hottest Die(5)
(Each Channel)
(Each Channel)
(Each Channel)
Non-Transmitting-(typ/max)
Transmitting-50% duty cycle (typ/max)
Transmitting-100% duty cycle (typ/max)
0.45/0.68 W
0.85/1.45 W
1.30/2.23 W
0.45/0.68 W
0.85/1.45 W
1.30/2.23 W
0.39/0.59 W
0.81/1.36 W
1.30/2.16 W
MECHANICAL
Package Style
Dimensions
30 Pin DDIP
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1.895” x 0.775” x 0.210”
48.13 mm x19.69 mm x 5.33 mm
36 Pin Flat Pack
1.905” x 0.785” x 0.165”
48.39 mm x 19.94 mm x 4.19 mm
0.6 oz
Package Style
Dimensions
Weight
17 (g)
6
NOTES for TABLE 3.
(1) On BUS-63102, filtering eliminates harmonics above 1 MHz. Differential group delay is ± 35 ns (10 kHz-2 MHz).
(2) The Threshold Level, as referred to in this specification, is meant to be the maximum peak-to-peak voltage
(measured on the Data Bus) that can be applied to the receivers’ input without causing the output to change
from the OFF state.
(3) On BUS-63102 and BUS-63104, external threshold levels are adjustable from 0V to 2V, with two external 10K Ohm
potentiometers. Connect one pot between pin 5 and GND and the other between pin 12 and GND.
(4) On BUS-63102, Output Level (direct coupled) is 30 V pk-pk.
BUS-63137
BUS-63138
Dual
-12 VDC
Smiths
BUS-29854
(5) On BUS-63102 and BUS-63104, Hottest Die are defined as the driver transistors.
* Same as value to the left.
† BUS-63105 available as Military (DESC) drawing 5962-86049-02ZC
†† BUS-63125 and BUS-63126 are available as Military (DESC) drawing 5962-87579.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
(Total Hybrid)
+5 VDC ±10% -12 VDC ±5%
60/90 mA
60/90 mA
60/90 mA
40/60 mA
135/185 mA
230/305 mA
*
*
*
*
*
(Total Hybrid,
One Channel Transmitting)
0.78/1.18 W
1.20/1.95 W
1.69/2.75 W
(Each Channel)
0.39/0.59 W
0.81/1.36 W
1.30/2.16 W
*
*
*
*
*
*
*
*
7
On all other models, BUS-63107, BUS-63125 and BUS-63127,
receiver outputs are both at a logic “0” when they are either
strobed off, or no signal is being received. This makes these
models directly compatible with the Harris type
encoder/decoder. Typical operating waveforms are shown in
FIGURE 4.
RECEIVER OPERATING MODE
The receiver section accepts data from a MIL-STD-1553 Data
Bus when properly coupled through a transformer in either the
long stub or short stub configuration. The data is converted to
bi-phase TTL and provided to the RX Data and RX Data output
terminals for decoding. Applying a logic “1” to the STROBE
input enables data to pass through to the receiver output(outut
enabled). Applying a logic “0” to the STROBE input turns the
receiver output OFF (output disabled).
On BUS-63102, BUS-63104, BUS-63115, BUS-63117 and
BUS-63137 receiver outputs are both at a logic “1” when they
are either strobed off, or no signal is being received. This makes
these models directly compatible with the Smiths type
encoder/decoder. Typical operating waveforms are shown in
FIGURE 3.
TX Data In
X X X
X X X
X X X
X X X
ENCODER
OUTPUT
TX Data In
LINE-TO-LINE
OUTPUT
LINE-TO-LINE
INPUT
RX Data Out
RX Data Out
TX Data In
X X X
X X X
X X X
X X X
ENCODER
OUTPUT
Notes:
TX Data In
(1) TX Data In and RX Data Out are TTL signals.
(2) TX Data In inputs must be at opposite logic levels during transmission, and at
the same logic level when not transmitting.
(3) LINE-TO-LINE output voltage is measured between TX Data Out and TX Data Out.
(4) LINE-TO-LINE input voltage is measured on the Data Bus.
LINE-TO-LINE
OUTPUT
LINE-TO-LINE
INPUT
RX Data Out
RX Data Out
FIGURE 4. TYPICAL OPERATING WAVEFORMS
FOR HARRIS-COMPATIBLE TRANS-
CEIVER
Notes:
(1) TX Data In and RX Data Out are TTL signals.
(2) TX Data In inputs must be at opposite logic levels during transmission, and at
the same logic level when not transmitting.
(3) LINE-TO-LINE output voltage is measured between TX Data Out and TX Data Out.
(4) LINE-TO-LINE output voltage for BUS-63102 are sinusoidal waveforms for
1 MHz operating frequency.
(5) LINE-TO-LINE input voltage is measured on the Data Bus.
FIGURE 3. TYPICAL OPERATING WAVEFORMS
FOR SMITHS-COMPATIBLE TRANS-
CEIVER
8
24 PIN SQUARE AND 24 PIN SQUARE FLAT PACK TRANS-
BUS-63102
BUS-63104
BUS-63112
BUS-63114
BUS-63102
BUS-63104
BUS-63112
BUS-63114
1.258 MAX
(31.95)
0.020 R
(0.51)
4 PLACES
0.042 DIA
(1.1)
1.100
(27.9)
TYP
0.550
(13.9)
REF
6
5
EXT Data Thresh
EXT Data Thresh
INT Data Thresh
INT Data Thresh
24
13
11
12
0.550
(13.9)
REF
TOP VIEW
1.258 MAX
(31.95)
1.100
(27.9)
0.100 ± 0.002
TOLERANCE
NON-CUMULATIVE
12
PIN #1
COLORKEY
-GLASS
EXTERNAL THRESHOLD
INTERNAL THRESHOLD
1
FIGURE 5. THRESHOLD CONNECTIONS
1.160
(29.5)
0.020 R
(0.51)
4 PLACES
SIDE VIEW
0.250
(6.35)
PIN
1
FUNCTION
0.018 ± 0.002 DIA.
(0.46 ± 0.06)
TYP
0.175 MAX
(4.4)
TX Data Out
TX Data Out
GND
2
3
4
+12 VDC to +15 VDC
EXT Data Thresh
INT Data Thresh
RX Data Out
5
FIGURE 6. BUS-63102 AND BUS-63104
MECHANICAL OUTLINE
6
7
24-PIN SQUARE PACKAGE
8
Strobe
9
GND
10
11
12
RX Data Out
INT Data Thresh
EXT Data Thresh
GLASS BEAD OF PIN 1
IS CONTRASTING COLOR
1.255 MAX
(31.877)
0.400±(10.16)
MIN(2 PLC'S)
13
14
15
16
17
18
19
20
21
22
23
24
+12 VDC to +15 VDC
NC
0.015±0.003
(0.381±0.076)
1
24
RX Data In
RX Data In
GND
1.255 MAX
(31.877)
TOP VIEW
GND (case)
-12 VDC to -15 VDC
+ 5 VDC
12
13
TX Inhibit
11 PINS EQUALLY SPACED
@0.100-1.100 TOLERANCE
NON-CUMULATIVE
TX Data In
0.075±0.005
(1.905±0.127)
TX Data In
(2.54=27.94)
0.160 MAX
(4.064)
-12 VDC to -15 VDC
NOTE:
SIDE VIEW
For internal threshold levels, ground pins 6 and 11.
For external threshold, connect two 10K Ohm pots (one between pin 5 and GND,
and the other between pin 12 and GND). See FIGURE 5.
0.010±0.002
(0.254±0.051)
0.075±0.005
(1.905±0.127)
FIGURE 7. BUS-63312 AND BUS-63114
MECHANICAL OUTLINE
TABLE 4. BUS-63102, BUS63104, 24-PIN SQUARE
AND BUS-63112, BUS63114, 24-PIN
24-PIN SQUARE PACKAGE
FLAT PACK PIN CONNECTIONS
9
24 PIN DDIP AND 24 PIN FLAT PACK TRANSCEIVERS
1.31 MAX
(33.27)
0.170 MAX
0.600 TYP
24
1
13
12
PIN
1
FUNCTION
TX Data Out
TX Data Out
GND
0.8 MAX
(20.32)
PIN NUMBERS
FOR REF ONLY
2
3
TOP VIEW
4
NC
5
NC
11 PINS EQUALLY SPACED
@0 1 00 = 1.100 TOLERANCE
NON-CUMULATIVE
6
NC
(2.54 x 11 = 27.94 ± 0.127)
7
RX Data Out
0.170 MAX
(4.38)
8
Strobe
GND
0.100 TYP
(2.54)
9
PIN NO 1
ORIENTATION
MARK
0.025 TYP
(0.635)
10
11
12
RX Data Out
NC
0.018 ± 0.002 TYP
(0.457 ± 0.051)
NC
13
14
15
16
17
18
19
20
21
22
23
24
NC
0.230 REF
(5.842)
0.40 TYP
(1.016)
NC
SIDE VIEW
RX Data In
RX Data In
NC
FIGURE 8. BUS-63105, BUS-63107,
BUS-63115, AND BUS-63117
MECHANICAL OUTLINE
GND
-12 VDC or -15 VDC
+ 5 VDC
24-PIN SQUARE DDIP
TX Inhibit
TX Data In
TX Data In
NC
PIN 1 DENOTED BY
CONTRASTING COLORED BEAD
PIN NUMBERS
FOR REF ONLY
0.775 MAX
(19.685)
1
24
11 PINS EQUALLY SPACED
TABLE 5. BUS-63105, BUS63107, BUS-63115,
BUS-63117, 24 PIN DDIP AND
BUS-63106, BUS-63108,
@0.100=1.100 TOLERANCE
NON-CUMULATIVE
1.275 MAX
(32.385)
TOP VIEW
0.100 TYP
(2.54)
BUS-63116, BUS63118, 24 PIN FLAT
PACK
PIN CONNECTIONS
12
13
0.015±0.003 TYP
(0.381±0.076)
0.500 MIN TYP
(12.70)
0.085±0.010 REF
(2.16±0.254)
SIDE VIEW
0.010±0.002 TYP
(0.254±0.051)
0.175 MAX
(4.45)
0.072
(1.83)
FIGURE 9. BUS-63106, BUS-63108,
BUS-63116, AND BUS-63118
MECHANICAL OUTLINE
24-PIN FLAT PACK
10
36 PIN DDIP AND 36 PIN FLAT PACK TRANSCEIVERS
PIN
1
FUNCTION
TX Data Out
TX Data Out
GND
*
*
*
0.09±0.01
(2.3±0.25)
1.700±0.005
(43.2±0.13)
2
0.1±0.01
(2.5±0.3)
3
4
NC
*
19
18
36
1
0.775±0.005
(19.7±0.13)
0.600±0.005
(15.2±0.13)
5
RX Data Out
Strobe
*
*
TOP VIEW
6
7
GND
*
0.086 TYP (2.2)
RADIUS
DOT
IDENTIFIES
PIN 1
8
RX Data Out
GND (case)
TX Data Out
TX Data Out
GND
*
1.895±0.005
(48.2±0.13)
9
*
0.21 MAX
(5.3)
0.015 MAX
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
* *
* *
* *
*
(0.39)
SIDE VIEW
0.100±0.002
0.055 TYP (1.4)
RADIUS
SEATING
PLANE
NC
TOLERANCE
NON-CUMULATIVE
RX Data Out
Strobe
* *
* *
* *
* *
*
CENTER TO CENTER
AT SEATING PLANE
0.25 MIN
(6.4)
0.018±0.002 DIA
(0.46±0.06)
Gnd
RX Data Out
NC
NC
*
FIGURE 10. BUS-63125, BUS-63127,
BUS-63135, AND BUS-63137
MECHANICAL OUTLINE
36-PIN DDIP
RX Data In
RX Data In
GND
* *
* *
* *
* *
* *
* *
* *
* *
*
-12 VDC or -15 VDC
+5 VDC
Inhibit
TX Data In
TX Data In
NC
0.250 MIN
(6.35)
0.785 MAX
(20.0)
RX Data In
RX Data In
GND
*
1
36
*
*
0.100 TYP
(2.54)
1.905 MAX
(48.4)
-12 VDC or -15 VDC
+5 VDC
*
*
TOP VIEW
Inhibit
*
0.015 TYP
(0.381)
TX Data In
TX Data In
*
*
NOTES:
19
17 EQUAL SPACES
@0.100=1.700 TOLERANCE
NON-CUMULATIVE
(2.54 = 43.18)
(1) -12 VDC for BUS-63127, BUS-63128, BUS-63137, and BUS-63138.
(2) -15 VDC for BUS-63125, BUS-63126, BUS-63135, and BUS-63136
18
0.165 MAX
0.010±0.002
(0.254±0.051)
(4.2)
* Channel One
* * Channel Two
SIDE VIEW
TABLE 6. BUS-63125, BUS63127,
BUS-63135, BUS-63137, 36-PIN DDIP AND
BUS-63126, BUS-63128, BUS-63136,
BUS63138, 36-PIN FLAT PACK
PIN CONNECTIONS
FIGURE 11. BUS-63126, BUS-63128,
BUS-63136, AND BUS-63138
MECHANICAL OUTLINE
36-PIN FLAT PACK
11
SINGLE TRANSCEIVERS
ORDERING INFORMATION
ORDERING INFORMATION
BUS-631XX- XX0X
BUS-631XX- XX0X
Supplemental Process Requirements:
Supplemental Process Requirements:
S = Pre-Cap Source Inspection
L = Pull Test
S = Pre-Cap Source Inspection
L = Pull Test
Q = Pull Test and Pre-Cap Inspection
K = One Lot Date Code
W = One Lot Date Code and
PreCap Source
Q = Pull Test and Pre-Cap Inspection
K = One Lot Date Code
W = One Lot Date Code and
PreCap Source
Y = One Lot Date Code and
100% Pull Test
Y = One Lot Date Code and
100% Pull Test
Z = One Lot Date Code,
PreCap Source and 100% Pull Test
Blank = None of the Above
Process Requirements:
0 = Standard DDC Processing,
no Burn-In (See page xiii.)
1 = MIL-PRF-38534 Compliant
2 = B*
Z = One Lot Date Code,
PreCap Source and 100% Pull Test
Blank = None of the Above
Process Requirements:
0 = Standard DDC Processing,
no Burn-In (See page xiii.)
1 = MIL-PRF-38534 Compliant
2 = B*
3 = MIL-PRF-38534
3 = MIL-PRF-38534
Compliant with PIND Testing
4 = MIL-PRF-38534
Compliant with PIND Testing
4 = MIL-PRF-38534
Compliant with Solder Dip
5 = MIL-PRF-38534
Compliant with Solder Dip
5 = MIL-PRF-38534 Compliant
with PIND Testing and Solder Dip
6 = B* with PIND Testing
7 = B* with Solder Dip
8 = B* with PIND Testing
and Solder Dip
Compliant with PIND Testing
and Solder Dip
6 = B* with PIND Testing
7 = B* with Solder Dip
8 = B* with PIND Testing
and Solder Dip
9 = Standard DDC Processing
with Solder Dip,
9 = Standard DDC Processing
with Solder Dip,
no Burn-In (See page xiii.)
Temperature Grade/Data Requirements:
1 = -55°C to +125°C
no Burn-In (See page xiii.)
Temperature Grade/Data Requirements:
1 = -55°C to +125°C
2 = -40°C to +85°C
2 = -40°C to +85°C
3 = 0°C to +70°C
3 = 0°C to +70°C
4 = -55°C to +125°C
4 = -55°C to +125°C
with Variables Test Data
5 = -40°C to +85°C
with Variables Test Data
8 = 0°C to +70°C
with Variables Test Data
5 = -40°C to +85°C
with Variables Test Data
8 = 0°C to +70°C
with Variables Test Data
Type
with Variables Test Data
Power Supply and Packaging
5 = -15 V DDIP
2 = Universal Transceiver
(MACAIR and 1553) ±12V to ±15 V
power supply range.
6 = -15 V Flat Pack
7 = -12 V DDIP
Compatible with
8 = -12 V Flat Pack
Smith’s Encoder/Decoder
4 = 1553, ±12V to ±15V power supply
range, compatible with Smith’s
Encoder/Decoder
Encoder/Decoder Compatibility
0 = Compatible with Harris
Encoder/Decoder
1 = Compatible with Smith
Encoder/Decoder
Packaging
0 = 24-Pin Square DIP
1 = 24-Pin Square Flat Pack
*Standard DDC Processing with burn-in and full temperature.
BUS-63105 also available as DESC drawing 5962-86049-02ZC.
See FIGURE 2 for mating transformer.
*Standard DDC Processing with burn-in and full temperature test.
See FIGURE 2 for mating transformer.
12
DUAL TRANSCEIVERS
ORDERING INFORMATION
BUS-631XX- XX0X
Supplemental Process Requirements:
S = Pre-Cap Source Inspection
L = Pull Test
Q = Pull Test and Pre-Cap Inspection
K = One Lot Date Code
W = One Lot Date Code and PreCap Source
Y = One Lot Date Code and 100% Pull Test
Z = One Lot Date Code, PreCap Source and 100% Pull Test
Blank = None of the Above
Process Requirements*:
0 = Standard DDC Processing, no Burn-In (See page xiii.)
1 = MIL-PRF-38534 Compliant
2 = B*
3 = MIL-PRF-38534 Compliant with PIND Testing
4 = MIL-PRF-38534 Compliant with Solder Dip
5 = MIL-PRF-38534 Compliant with PIND Testing and Solder Dip
6 = B** with PIND Testing
7 = B** with Solder Dip
8 = B** with PIND Testing and Solder Dip
9 = Standard DDC Processing with Solder Dip, no Burn-In (See page xiii.)
Temperature Grade/Data Requirements:
1 = -55°C to +125°C
2 = -40°C to +85°C
3 = 0°C to +70°C
4 = -55°C to +125°C with Variables Test Data
5 = -40°C to +85°C with Variables Test Data
8 = 0°C to +70°C with Variables Test Data
Power Supply and Packaging
5 = -15 V DDIP
6 = -15 V Flat Pack
7 = -12 V DDIP
8 = -12 V Flat Pack
Encoder/Decoder Compatibility
2 = Compatible with Harris Encoder/Decoder
3 = Compatible with Smith Encoder/Decoder
*Available as BUS-63125-641 (BUS-65612 compatible Transceiver).
**Standard DDC Processing with burn-in and full temperature test.
BUS-63125 and BUS-63126 are available as DESC drawing 5962-86049.
See FIGURE 2 for mating transformer.
STANDARD DDC PROCESSING
MIL-STD-883
METHOD(S)
TEST
CONDITION(S)
INSPECTION
SEAL
2009, 2010, 2017, and 2032
—
1014
1010
A and C
TEMPERATURE CYCLE
CONSTANT ACCELERATION
BURN-IN
C
A
2001
1015, Table 1
—
13
NOTES
14
NOTES
15
The information in this data sheet is believed to be accurate; however, no responsibility is
assumed by Data Device Corporation for its use, and no license or rights are
granted by implication or otherwise in connection therewith.
Specifications are subject to change without notice.
105 Wilbur Place, Bohemia, New York 11716-2482
For Technical Support - 1-800-DDC-5757 ext. 7257 or 7381
Headquarters - Tel: (631) 567-5600 ext. 7257 or 7381, Fax: (631) 567-7358
Southeast - Tel: (703) 450-7900, Fax: (703) 450-6610
West Coast - Tel: (714) 895-9777, Fax: (714) 895-4988
Europe - Tel: +44-(0)1635-811140, Fax: +44-(0)1635-32264
Asia/Pacific - Tel: +81-(0)3-3814-7688, Fax: +81-(0)3-3814-7689
World Wide Web - http://www.ddc-web.com
ILC DATA DEVICE CORPORATION
REGISTERED TO ISO 9001
FILE NO. A5976
K-08/98-0
PRINTED IN THE U.S.A.
16
相关型号:
©2020 ICPDF网 联系我们和版权申明