CS5205-1/D_技术文档

CS5205-1, CS5205-3,

CS5205-5

5.0 A Adjustable, and

3.3 V and 5.0 V Fixed

Linear Regulators

http://onsemi.com

The CS5205–x series of linear regulators provides 5.0 A at

adjustable and fixed voltages with an accuracy of ±1.0% and ±2.0%

respectively. The adjustable version uses two external resistors to set

the output voltage within a 1.25 V to 13 V range.

Adjustable

Output

The regulators are intended for use as post regulators and

microprocessor supplies. The fast loop response and low dropout

voltage make these regulators ideal for applications where low voltage

operation and good transient response are important.

TO–220

THREE LEAD

T SUFFIX

Tab = V

OUT

Pin 1. Adj

2. V

OUT

CASE 221A

3. V

IN

The circuit is designed to operate with dropout voltages as low as

1.0 V depending on the output current level. The maximum quiescent

current is only 10 mA at full load.

The regulators are fully protected against overload conditions with

protection circuitry for Safe Operating Area (SOA), overcurrent and

thermal shutdown.

1

2

Fixed

3

Output

2

Tab = V

D PAK

OUT

Pin 1. GND

3–PIN

DP SUFFIX

CASE 418E

2. V

OUT

3. V

1

IN

2

3

The CS5205–x is pin compatible with the LT1084 family of linear

regulators but has lower dropout voltage.

MARKING DIAGRAMS

2

The regulators are available in TO–220 and surface mount D PAK

TO–220

D PAK

packages.

Features

• Output Current to 5.0 A

CS5205–X

AWLYWW

CS5205–X

AWLYWW

• Output Trimmed to ±1.0%

• Dropout Voltage 1.2 V @ 5.0 A

• Fast Transient Response

• Fault Protection Circuitry

– Thermal Shutdown

1

A

= Assembly Location

WL, L = Wafer Lot

YY, Y = Year

– Overcurrent Protection

– Safe Area Protection

WW, W = Work Week

ORDERING INFORMATION*

Device

Package

Shipping

V

OUT

V

IN

CS5205–1GT3

CS5205–1GDP3

CS5205–1GDPR3

CS5205–3GT3

CS5205–3GDP3

CS5205–3GDPR3

CS5205–5GT3

TO–220†

50 Units/Rail

2

D PAK†

2

D PAK† 750 Tape & Reel

Output

Current

Limit

TO–220†

50 Units/Rail

Thermal

Shutdown

2

D PAK†

–

+

Error

Amplifier

2

D PAK† 750 Tape & Reel

Adj

Bandgap

TO–220†

50 Units/Rail

*Additional ordering information can be found on page 7

of this data sheet.

2

Figure 1. Block Diagram – CS5205–1

†TO–220 is 3–pin, straight leaded. D PAK are all 3–pin.

Semiconductor Components Industries, LLC, 2001

1

Publication Order Number:

March, 2001 – Rev. 4

CS5205–1/D

CS5205–1, CS5205–3, CS5205–5

V

OUT

V

IN

Output

Current

Limit

Thermal

Shutdown

–

+

Error

Amplifier

Bandgap

GND

Figure 2. Block Diagram – CS5205–3, –5

Parameter

ABSOLUTE MAXIMUM RATINGS*

Value

17

Unit

V

Supply Voltage, V

CC

Operating Temperature Range

Junction Temperature

–40 to +70

150

°C

Storage Temperature Range

Lead Temperature Soldering:

–60 to +150

Wave Solder (through hole styles only) Note 1.

Reflow (SMD styles only) Note 2.

260 Peak

230 Peak

°C

1. 10 second maximum.

2. 60 second maximum above 183°C.

*The maximum package power dissipation must be observed.

ELECTRICAL CHARACTERISTICS (C = 10 µF, C

= 22 µF Tantalum, V – V

= 3.0 V, V ≤ 15 V,

OUT IN

IN

OUT

IN

0°C ≤ T ≤ 70°C, T ≤ +150°C, unless otherwise specified, I

= 5.0 A.)

A

J

full load

Characteristic

Test Conditions

Min

Typ

Max

Unit

Adjustable Output Voltage (CS5205–1)

Reference Voltage (Notes 3. and 4.)

V

– V

= 1.5 V; V = 0 V,

1.241

(–1%)

1.254

1.266

(+1%)

V

IN

OUT

Adj

10 mA ≤ I

≤ 5.0 A

OUT

Line Regulation

1.5 V ≤ V – V

≤ 6.0 V; I = 10 mA

OUT

–

0.04

0.08

1.2

0.20

0.4

%

V

IN

OUT

Load Regulation (Notes 3. and 4.)

Dropout Voltage (Note 5.)

Current Limit

V

IN

– V

= 1.5 V; 10 mA ≤ I

≤ 5.0 A

OUT

I

= 5.0 A

1.3

OUT

V

IN

V

IN

– V

= 3.0 V; T ≥ 25°C

= 9.0 V

5.5

–

8.5

1.0

–

A

OUT

J

Minimum Load Current

Adjust Pin Current

V

– V

= 7.0 V

–

1.2

50

6.0

100

5.0

mA

µA

IN

OUT

–

Adjust Pin Current Change

1.5 V ≤ V – V

≤ 4.0 V;

0.2

IN

OUT

10 mA ≤ I

≤ 5.0 A

OUT

Thermal Regulation

30 ms pulse; T = 25°C

–

0.003

–

%W

A

3. Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output

voltage due to thermal gradients or temperature changes must be taken into account separately.

4. Specifictions apply for an external Kelvin sense connection at a point on the output pin 1/4” from the bottom of the package.

5. Dropout voltage is a measurement of the minimum input/output differentail at full load.

http://onsemi.com

2

CS5205–1, CS5205–3, CS5205–5

ELECTRICAL CHARACTERISTICS (continued) (C = 10 µF, C

= 22 µF Tantalum, V – V

= 3.0 V, V ≤ 15 V,

OUT IN

IN

OUT

IN

0°C ≤ T ≤ 70°C, T ≤ +150°C, unless otherwise specified, I

= 5.0 A.)

A

J

full load

Characteristic

Test Conditions

Min

Typ

Max

Unit

Adjustable Output Voltage (CS5205–1) (continued)

Ripple Rejection

f = 120 Hz; C = 25 µF; I

= 5.0 A

–

82

0.5

–

dB

%

Adj

OUT

Temperature Stability

RMS Output Noise

–

10 Hz ≤ f ≤ 10 kHz; T = 25°C

–

0.003

180

25

%V

OUT

A

Thermal Shutdown

–

150

–

°C

Thermal Shutdown Hysteresis

ELECTRICAL CHARACTERISTICS (C = 10 µF, C

= 22 µF Tantalum, V – V

= 3.0 V, V ≤ 10 V,

OUT IN

IN

OUT

IN

0°C ≤ T ≤ 70°C, T ≤ +150°C, unless otherwise specified, I

= 5.0 A.)

A

J

full load

Characteristic

Test Conditions

Min

Typ

Max

Unit

Fixed Output Voltage (CS5205–3, CS5205–5)

Reference Voltage (Notes 6. and 7.)

CS5205–5

CS5205–3

V

IN

V

IN

– V

= 1.5 V; 0 ≤ IOUT ≤ 5.0 A

4.9 (–2%)

3.234 (–2%)

5.0

3.3

5.1 (+2%)

3.366 (+2%)

V

OUT

Line Regulation

1.5 V ≤ V – V

≤ 6.0 V; I = 10 mA

OUT

–

0.04

0.08

1.2

0.20

0.40

1.3

%

V

IN

OUT

Load Regulation (Notes 6. and 7.)

Dropout Voltage (Note 8.)

Current Limit

V

IN

– V

= 1.5 V; 10 mA ≤ I

≤ 5.0 A

OUT

I

= 5.0 A

OUT

V

IN

V

IN

– V

= 3.0 V; T ≥ 25°C

= 9.0 V

5.5

–

8.5

1.0

–

A

OUT

J

Quiescent Current

Thermal Regulation

Ripple Rejection

V

≤ 9.0 V; I

= 10 mA

–

5.0

0.003

75

10

–

mA

%W

dB

IN

OUT

30 ms pulse; T = 25°C

A

f = 120 Hz; I

= 5.0 A

–

OUT

Temperature Stability

–

0.5

–

%

RMS Output Noise (%V

Thermal Shutdown

)

10 Hz ≤ f ≤ 10 kHz

–

0.003

180

25

–

%V

OUT

–

150

–

°C

Thermal Shutdown Hysteresis

–

6. Load regulation and output voltage are measured at a constant junction temperature by low duty cycle pulse testing. Changes in output

voltage due to thermal gradients or temperature changes must be taken into account separately.

7. Specifictions apply for an external Kelvin sense connection atr a point on the output pin 1/4” from the bottom of the package.

8. Dropout voltage is a measurement of the minimum input/output differentail at full load.

PACKAGE PIN DESCRIPTION

Package Pin Number

CS5205–1

CS5205–3, –5

2

D PAK

TO–220

D PAK

TO–220

Pin Symbol

Function

1

2

1

2

N/A

2

N/A

2

Adj

Adjust pin (low side of the internal reference).

V

OUT

Regulated output voltage (case).

Input voltage.

3

V

IN

N/A

1

GND

Ground connection.

http://onsemi.com

3

CS5205–1, CS5205–3, CS5205–5

TYPICAL PERFORMANCE CHARACTERISTICS

0.10

0.08

0.06

1.30

1.25

1.20

1.15

1.10

1.05

1.00

0.95

0.90

0.85

0.80

0.75

0.70

0.04

T

= 0°C

CASE

0.02

0.00

–0.02

–0.04

T

= 125°C

CASE

T

= 25°C

CASE

–0.06

–0.08

–0.10

–0.12

0

1

2

3

4

5

0

10 20 30 40 50 60 70 80 90 100 110 120 130

Output Current (A)

T (°C)

J

Figure 3. Dropout Voltage vs. Output

Current

Figure 4. Reference Voltage vs.

Temperature

0.200

0.175

0.150

0.125

0.100

0.075

0.050

0.025

0.000

2.500

2.175

1.850

1.525

1.200

0.875

0.550

T

= 0°C

CASE

T

= 25°C

CASE

T

= 25°C

CASE

T

= 125°C

CASE

1

T

= 0°C

CASE

4

T

= 125°C

CASE

7

0

2

3

5

1

2

3

4

5

6

8

9

Output Current (A)

V

IN

– V

(V)

OUT

Figure 5. Load Regulation vs. Output

Current

Figure 6. Minimum Load Current

100

90

80

70

60

50

40

30

20

10

0

70

65

60

55

50

45

I

= 10 mA

O

T

= 25°C

= 5.0 A

CASE

I

OUT

(V – V

V

) = 3.0 V

OUT

IN

= 1.6 V

RIPPLE

PP

40

0

1

2

3

4

5

10 20 30 40 50 60 70 80 90 100 110 120 130

10

Temperature (°C)

Frequency (Hz)

Figure 7. Adjust Pin Current vs.

Temperature

Figure 8. Ripple Rejection vs. Frequency

(Fixed Versions)

http://onsemi.com

4

CS5205–1, CS5205–3, CS5205–5

100

90

80

70

60

50

40

30

20

10

0

T

= 25°C

= 5.0 A

CASE

I

OUT

(V – V

V

C

) = 3.0 V

OUT

IN

= 1.6 V

PP

RIPPLE

= 25 µF

Adj

1

2

3

4

5

10

Frequency (Hz)

Figure 9. Ripple Rejection vs. Frequency

(Adjustable Versions)

APPLICATIONS INFORMATION

The CS5205–x family of linear regulators provide fixed

or adjustable voltages at currents up to 5.0 A. The regulators

are protected against short circuit, and include thermal

shutdown and safe area protection (SOA) circuitry. The

SOA protection circuitry decreases the maximum available

output current as the input–output differential voltage

increases.

The CS5205–x has a composite PNP–NPN output

transistor and requires an output capacitor for stability. A

detailed procedure for selecting this capacitor is included in

the Stability Considerations section.

V

IN

V

OUT

V

OUT

V

IN

CS5205–1

C

1

V

REF

Adj

R

1

2

C

2

I

Adj

C

Adj

Adjustable Operation

Figure 10. Resistor Divider Scheme for the

Adjustable Version

The adjustable regulator (CS5205–1) has an output

voltage range of 1.25 V to 13 V. An external resistor divider

sets the output voltage as shown in Figure 10. The regulator

maintains a fixed 1.25 V (typical) reference between the

output pin and the adjust pin.

A resistor divider network R1 and R2 causes a fixed

current to flow to ground. This current creates a voltage

across R2 that adds to the 1.25 V across R1 and sets the

overall output voltage. The adjust pin current (typically

50 µA) also flows through R2 and adds a small error that

Stability Considerations

The output or compensation capacitor helps determine

three main characteristics of a linear regulator: start–up

delay, load transient response and loop stability.

The capacitor value and type is based on cost, availability,

size and temperature constraints. A tantalum or aluminum

electrolytic capacitor is best, since a film or ceramic

capacitor with almost zero ESR, can cause instability. The

aluminum electrolytic capacitor is the least expensive

solution. However, when the circuit operates at low

temperatures, both the value and ESR of the capacitor will

vary considerably. The capacitor manufacturers data sheet

provides this information.

should be taken into account if precise adjustment of V

is necessary.

The output voltage is set according to the formula:

OUT

R1 ) R2

ǒ

Ǔ_) I

V

+ V

R2

OUT

REF

Adj

R1

The term I × R2 represents the error added by the adjust

pin current.

A 22 µF tantalum capacitor will work for most

applications, but with high current regulators such as the

CS5205–x the transient response and stability improve with

higher values of capacitor. The majority of applications for

this regulator involve large changes in load current so the

output capacitor must supply the instantaneous load current.

Adj

R1 is chosen so that the minimum load current is at least

10 mA. R1 and R2 should be the same type, e.g. metal film

for best tracking over temperature. The adjust pin is

bypassed to improve the transient response and ripple

rejection of the regulator.

http://onsemi.com

5

CS5205–1, CS5205–3, CS5205–5

Output Voltage Sensing

The ESR of the output capacitor causes an immediate drop

in output voltage given by:

Since the CS5205–x is a three terminal regulator, it is not

possible to provide true remote load sensing. Load

regulation is limited by the resistance of the conductors

connecting the regulator to the load. For best results the

fixed regulators should be connected as shown in Figure 13.

DV + DI ESR

For microprocessor applications it is customary to use an

output capacitor network consisting of several tantalum and

ceramic capacitors in parallel. This reduces the overall ESR

and reduces the instantaneous output voltage drop under

load transient conditions. The output capacitor network

should be as close as possible to the load for the best results.

Conductor Parasitic

Resistance

R

C

V

IN

V

IN

V

OUT

CS5205–x

R

LOAD

Protection Diodes

Gnd

When large external capacitors are used with a linear

regulator it is sometimes necessary to add protection diodes.

If the input voltage of the regulator gets shorted, the output

capacitor will discharge into the output of the regulator. The

discharge current depends on the value of the capacitor, the

output voltage and the rate at which V drops. In the

IN

Figure 13. Conductor Parasitic Resistance can be

Minimized with the Above Grounding Scheme for

Fixed Output Regulators

CS5205–x family of linear regulators, the discharge path is

through a large junction and protection diodes are not

usually needed. If the regulator is used with large values of

output capacitance and the input voltage is instantaneously

shorted to ground, damage can occur. In this case, a diode

connected as shown in Figures 11 and 12 is recommended.

For the adjustable regulator, the best load regulation

occurs when R1 is connected directly to the output pin of the

regulator as shown in Figure 14. If R1 is connected to the

load, R is multiplied by the divider ratio and the effective

C

resistance between the regulator and the load becomes

IN4002 (optional)

R1 ) R2

ǒ

Ǔ

R

C

V

IN

V

IN

V

OUT

R1

CS5205–1

C

1

where R = conductor parasitic resistance.

C

Adj

R

1

C

2

Conductor Parasitic

Resistance

R

C

V

IN

V

IN

V

OUT

C

R

Adj

2

CS5205–1

R

1

2

R

LOAD

Adj

Figure 11. Protection Diode Scheme for Adjustable

Output Regulator

IN4002 (optional)

V

OUT

V

OUT

V

IN

V

IN

CS5205–x

C

1

Figure 14. Grounding Scheme for Adjustable Output

Regulator to Minimize Parasitics

Gnd

C

2

Figure 12. Protection Diode Scheme for Fixed Output

Regulators

http://onsemi.com

6

CS5205–1, CS5205–3, CS5205–5

Calculating Power Dissipation and Heat Sink

Requirements

A heat sink effectively increases the surface area of the

package to improve the flow of heat away from the IC and

into the surrounding air.

Each material in the heat flow path between the IC and the

outside environment has a thermal resistance. Like series

electrical resistances, these resistances are summed to

The CS5205–x series of linear regulators includes thermal

shutdown and current limit circuitry to protect the device.

High power regulators such as these usually operate at high

junction temperatures so it is important to calculate the

power dissipation and junction temperatures accurately to

ensure that an adequate heat sink is used.

determine R , the total thermal resistance between the

ΘJA

junction and the surrounding air.

The case is connected to V

on the CS5205–x,

OUT

1. Thermal Resistance of the junction to case, R

ΘJC

electrical isolation may be required for some applications.

Thermal compound should always be used with high current

regulators such as these.

(°C/W)

2. Thermal Resistance of the case to Heat Sink, R

ΘCS

(°C/W)

The thermal characteristics of an IC depend on the

following four factors:

3. Thermal Resistance of the Heat Sink to the ambient

air, R (°C/W)

ΘSA

These are connected by the equation:

1. Maximum Ambient Temperature T (°C)

A

2. Power dissipation P (Watts)

D

3. Maximum junction temperature T (°C)

4. Thermal resistance junction to ambient R

J

R

+ R

ΘJA

) R

QSA

(3)

QJA

QJC

QCS

(°C/W)

ΘJA

The value for R

is calculated using equation (3) and

the result can be substituted in equation (1).

The value for R is 3.5°C/W for a given package type

These four are related by the equation

ΘJC

T + T ) P R

QJA

(1)

based on an average die size. For a high current regulator

such as the CS5205–x the majority of the heat is generated

J

A

D

The maximum ambient temperature and the power

dissipation are determined by the design while the

maximum junction temperature and the thermal resistance

depend on the manufacturer and the package type.

in the power transistor section. The value for R

depends

ΘSA

on the heat sink type, while R

depends on factors such

ΘCS

as package type, heat sink interface (is an insulator and

thermal grease used?), and the contact area between the heat

sink and the package. Once these calculations are complete,

The maximum power dissipation for a regulator is:

the maximum permissible value of R

can be calculated

ΘJA

{

}

I

P

+ V

* V

) V

I

D(max)

IN(max)

OUT(min) OUT(max)

IN(max) Q

and the proper heat sink selected. For further discussion on

heat sink selection, see application note “Thermal

Management for Linear Regulators,” document number

SR006AN/D, available through the Literature Distribution

Center or via our website at http://onsemi.com.

(2)

where:

V

is the maximum input voltage,

IN(max)

OUT(min)

OUT(max)

is the minimum output voltage,

is the maximum output current, for the

I

application

I is the maximum quiescent current at I

.

OUT(max)

Q

ADDITIONAL ORDERING INFORMATION

Orderable Part

Number

Type

Description

CS5205–1GT3

CS5205–1GDP3

CS5205–1GDPR3

CS5205–3GT3

CS5205–3GDP3

CS5205–3GDPR3

CS5205–5GT3

5.0 A, Adj. Output

5.0 A, 3.3 V Output

5.0 A, 5.0 V Output

TO–220 THREE LEAD, STRAIGHT

2

D PAK 3–PIN

2

D PAK 3–PIN (Tape & Reel)

TO–220 THREE LEAD, STRAIGHT

2

D PAK 3–PIN

2

D PAK 3–PIN (Tape & Reel)

TO–220 THREE LEAD, STRAIGHT

http://onsemi.com

7

CS5205–1, CS5205–3, CS5205–5

PACKAGE DIMENSIONS

TO–220

THREE LEAD

T SUFFIX

CASE 221A–09

ISSUE AA

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

SEATING

PLANE

–T–

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION Z DEFINES A ZONE WHERE ALL

BODY AND LEAD IRREGULARITIES ARE

ALLOWED.

C

B

F

T

S

4

1

INCHES

DIM MIN MAX

MILLIMETERS

MIN

14.48

9.66

4.07

0.64

3.61

2.42

2.80

0.46

12.70

1.15

4.83

2.54

2.04

1.15

5.97

0.00

1.15

---

MAX

15.75

10.28

4.82

0.88

3.73

2.66

3.93

0.64

14.27

1.52

5.33

3.04

2.79

1.39

6.47

1.27

---

A

K

Q

Z

A

B

C

D

F

0.570

0.380

0.160

0.025

0.142

0.095

0.110

0.018

0.500

0.045

0.190

0.100

0.080

0.045

0.235

0.000

0.045

---

0.620

0.405

0.190

0.035

0.147

0.105

0.155

0.025

0.562

0.060

0.210

0.120

0.110

0.055

0.255

0.050

---

2

3

U

H

G

H

J

K

L

R

N

Q

R

S

T

V

J

G

D

U

V

Z

N

0.080

2.04

D²PAK

3–PIN

DP SUFFIX

CASE 418E–01

ISSUE O

SEATING

PLANE

–T–

NOTES:

B

1. DIMENSIONS AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

C

M

E

4

INCHES

DIM MIN MAX

MILLIMETERS

MIN

8.28

10.05

4.31

0.66

1.14

2.29

MAX

8.53

10.31

4.57

0.91

1.40

2.79

A

B

C

D

E

F

0.326

0.396

0.170

0.026

0.045

0.090

0.336

0.406

0.180

0.036

0.055

0.110

A

K

1

2

3

G

H

J

0.100 BSC

2.54 BSC

0.098

0.108

0.025

0.214

0.055

0.066

0.004

2.49

0.46

5.18

1.14

1.40

0.00

2.74

0.64

5.44

1.40

1.68

0.10

0.018

0.204

0.045

0.055

0.000

F

K

L

M

N

H

G

D

3 PL

J

L

M

0.13 (0.005)

T

B

N

http://onsemi.com

8

CS5205–1, CS5205–3, CS5205–5

PACKAGE THERMAL DATA

2

TO–220

D PAK

THREE LEAD

3–PIN

Parameter

Unit

°C/W

R

Typical

1.6

50

1.6

Θ

JC

JA

10–50*

* Depending on thermal properties of substrate. R

= R

+ R

Θ

JC CA

Θ

JA

http://onsemi.com

9

CS5205–1, CS5205–3, CS5205–5

Notes

http://onsemi.com

10

CS5205–1, CS5205–3, CS5205–5

Notes

http://onsemi.com

11

CS5205–1, CS5205–3, CS5205–5

ON Semiconductor and

are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes

without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular

purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,

including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be

validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.

SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or

death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold

SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable

attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim

alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION

NORTH AMERICA Literature Fulfillment:

CENTRAL/SOUTH AMERICA:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)

Email: ONlit–spanish@hibbertco.com

Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada

Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada

Email: ONlit@hibbertco.com

ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support

Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)

Toll Free from Hong Kong & Singapore:

Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada

001–800–4422–3781

N. American Technical Support: 800–282–9855 Toll Free USA/Canada

Email: ONlit–asia@hibbertco.com

EUROPE: LDC for ON Semiconductor – European Support

German Phone: (+1) 303–308–7140 (M–F 1:00pm to 5:00pm Munich Time)

Email: ONlit–german@hibbertco.com

JAPAN: ON Semiconductor, Japan Customer Focus Center

4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031

Phone: 81–3–5740–2745

French Phone: (+1) 303–308–7141 (M–F 1:00pm to 5:00pm Toulouse Time)

Email: ONlit–french@hibbertco.com

English Phone: (+1) 303–308–7142 (M–F 12:00pm to 5:00pm UK Time)

Email: ONlit@hibbertco.com

Email: r14525@onsemi.com

ON Semiconductor Website: http://onsemi.com

EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781

For additional information, please contact your local

Sales Representative.

*Available from Germany, France, Italy, England, Ireland

CS5205–1/D

http://onsemi.com

12


型号：	CS5205-1/D
厂家：	ETC
描述：	5A Adjustable， and 3.3V and 5V Fixed Linear Regulators 5A可调和3.3V和5V固定线性稳压器稳压器
文件：	总12页 (文件大小：80K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

CS5205-1/D [ETC]

相关型号：

CS5205-1GDP3

CS5205-1GDP3

CS5205-1GDPR3

CS5205-1GT3

CS5205-1GT3

CS5205-2

CS5205-2/D

CS5205-2GDP3

CS5205-2GDPR3

CS5205-2GT3

CS5205-3

CS5205-3GDP3