D212RP [ETC]
Short Circuit Protected Regulated, 2W SIP DC/DC Converters; 短路保护功能调节, 2W SIP DC / DC转换器型号: | D212RP |
厂家: | ETC |
描述: | Short Circuit Protected Regulated, 2W SIP DC/DC Converters |
文件: | 总2页 (文件大小:91K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
D200RP Series
Short Circuit Protected
Regulatted, 2W SIP
DC/DC Convverteerrss
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
Conditions
Min.
4.5
Typ.
5.0
Max.
5.5
Units
5 VDC Input
● 2W Output Power
Input Voltage Range
12 VDC Input 10.8
24 VDC Input 21.6
π (Pi) Filter
12.0
24.0
13.2
26.4
VDC
● Short Circuit Protection
● Tight Line/Load Regulation
● 1,000 VDC Isolation
● Miniature SIP Case
● >1.5 MHour MTBF
Input Filter
Reverse Polarity Input Current
0.3
A
Output
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation (Note 1)
Ripple & Noise (20 MHz) (Note 2)
Output Power Protection
Temperature Coefficient
Output Short Circuit
General
Conditions
For Vin Min to Max
Min.
Typ.
Max.
2.0
0.5
0.5
75
Units
%
%
● 15 Standard Models
%
mV P - P
%
%/ºC
120
0.02
Continuous
Parameter
Conditions
Conditions
Min.
Typ.
Max.
Units
VDC
MΩ
pF
kHz
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
60 Seconds 1,000
500 VDC 1,000
100 kHz, 1V
60
40
Min.
Typ.
+25
Max.
+71
+85
Units
ºC
ºC
Ambient
Case
-25
-25
-40
+125
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
Case Material
Weight
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
1.26 x 0.32 x 0.55 Inches (32.0 x 8.0 x 14.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.17 Oz (4.8g)
T: (781) 344-8226
Reliability Specifications
Parameter
MTBF
F: (781) 344-8481
Conditions
Min.
Typ.
Typ.
Max.
Units
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
MIL HDBK 217F, 25ºC, Gnd Benign
1.5
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Max.
9.0
18.0
30.0
260
450
Units
5 VDC Input -0.7
12 VDC Input -0.7
24 VDC Input -0.7
Input Voltage Surge (1 Sec)
VDC
Lead Temperature
Internal Power Dissipation
1.5 mm From Case For 10 Sec
All Models
ºC
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Model Selection Guide
Input
Output
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Nominal Range
Current (mA)
Voltage
(VDC)
Current
Current
Number
(mA, Max) (mA, Min)
Full-Load No-Load
D201RP
D202RP
D203RP
D204RP
D205RP
D211RP
D212RP
D213RP
D214RP
D215RP
D221RP
D222RP
D223RP
D224RP
D225RP
5
5
5
5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
606
606
571
571
588
253
253
238
238
246
130
130
122
122
118
80
80
80
80
80
45
45
45
45
45
25
25
25
25
25
5.0
9.0
12.0
15.0
24.0
5.0
400.0
222.0
167.0
133.0
83.0
400.0
222.0
167.0
133.0
83.0
400.0
222.0
167.0
133.0
83.0
40.0
22.0
17.0
13.0
10.0
40.0
22.0
17.0
13.0
10.0
40.0
22.0
17.0
13.0
10.0
66
66
70
70
68
66
66
70
70
68
64
64
68
68
70
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
5
12
12
12
12
12
24
24
24
24
24
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
200
200
200
200
Derating2C4.u0 rve
200
Notes:
1. Output load regulation is specified for a load change
of 20% to 100%.
2. When measuring output ripple, it is recommended
that an external 0.33 μF ceramic capacitor be placed
from the +Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. These do not require external components to operate,
but the use of a low ESR capacitor (approximately
10 uF, ESR <1.0Ω at 100 kHz) mounted close to the
converter input pins is recommended.
5. It is recommended that a fuse be used on the input of
a power supply for protection. See the table above for
the correct rating.
Capacitive
Pin Connections
Load
Pin
1
Function
+Vin
NC
Mechanical Dimensions
μF Max
470
2
3
NC
9
NC
10
11
12
-Vout
+Vout
-Vin
NC: No Connection
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.01 ( 0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: sales@micropowerdirect.com
相关型号:
©2020 ICPDF网 联系我们和版权申明