D311RP [ETC]
Short Circuit Protected Regulated, 3W SIP DC/DC Converters; 短路保护功能调节， 3W SIP DC / DC转换器
| 型号： | D311RP |
| 厂家： | 
ETC |
| 描述： | Short Circuit Protected Regulated, 3W SIP DC/DC Converters |
| 文件： | 总2页 (文件大小：101K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Model Selection Guide
Input
Output
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Nominal Range
Current (mA)
Voltage
(VDC)
Current
Current
Number
(mA, Max) (mA, Min)
Full-Load No-Load
D301RP
D302RP
D303RP
D304RP
D305RP
D311RP
D312RP
D313RP
D314RP
D315RP
D321RP
D322RP
D323RP
D324RP
D325RP
5
5
5
5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
895
895
833
833
857
373
373
347
347
357
192
192
179
179
174
90
90
90
90
90
60
60
60
60
60
30
30
30
30
30
5.0
9.0
12.0
15.0
24.0
5.0
600.0
333.0
250.0
200.0
125.0
600.0
333.0
250.0
200.0
125.0
600.0
333.0
250.0
200.0
60.0
33.0
25.0
20.0
12.5
60.0
33.0
25.0
20.0
12.5
60.0
33.0
25.0
20.0
12.5
67
67
72
72
70
67
67
72
72
70
65
65
70
70
72
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
5
12
12
12
12
12
24
24
24
24
24
9.0
12.0
15.0
24.0
5.0
9.0
12.0
15.0
350
350
350
350
Derating2C4.u0 rve 125.0
350
Notes:
1. Output load regulation is specified for a load change
of 20% to 100%.
2. When measuring output ripple, it is recommended
that an external 0.33 μF ceramic capacitor be placed
from the +Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units.
However, they may not meet all specifications.
4. These do not require external components to operate,
but the use of a low ESR capacitor (approximately
10 uF, ESR <1.0Ω at 100 kHz) mounted close to the
converter input pins is recommended.
5. It is recommended that a fuse be used on the input of
a power supply for protection. See the table above for
the correct rating.
Capacitive
Pin Connections
Load
Pin
1
Function
+Vin
NC
Mechanical Dimensions
μF Max
470
2
3
NC
9
NC
10
11
12
-Vout
+Vout
-Vin
NC: No Connection
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.01 ( 0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: sales@micropowerdirect.com
相关型号：
©2020 ICPDF网 联系我们和版权申明