DEV-BF548 [ETC]
Bluetechnix Mechatronische Systeme GmbH; Bluetechnix Mechatronische系统有限公司
| 型号： | DEV-BF548 |
| 厂家： | 
ETC |
| 描述： | Bluetechnix Mechatronische Systeme GmbH |
| 文件： | 总36页 (文件大小：1181K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Hardware User Manual
DEV-BF548-Lite v1.x
DEV-BF548DA-Lite v1.x
Contact
Bluetechnix Mechatronische Systeme GmbH
Lainzerstraße 162/3
A-1130 Vienna
AUSTRIA/EUROPE
office@bluetechnix.at
http://www.bluetechnix.com
Document No.: 100-2246-1.0
Document Revision 13
2010-07-13
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
1
Table of Contents
1
Introduction..................................................................................................................................................................................8
1.1
Overview...............................................................................................................................................................................8
Functional Specification ........................................................................................................................................................ 10
PCB Placement and Mechanical Outline .......................................................................................................................... 11
2
3
3.1
PCB Placement................................................................................................................................................................. 11
Mechanical Outline ........................................................................................................................................................ 12
Extension Board Footprint........................................................................................................................................... 13
3.2
3.3
4
Connector Description ........................................................................................................................................................... 14
4.1
X4 –RJ45 Ethernet Connector..................................................................................................................................... 14
X9 –SD-Card Connector (bottom Mount)............................................................................................................... 14
X6 – JTAG Bypass Connector ...................................................................................................................................... 14
X11 – USB-UART Connectors ...................................................................................................................................... 14
X12 UART Expansion Pads ........................................................................................................................................... 14
X1, X2, X3 Expansion Connectors.............................................................................................................................. 15
X8, X10 – CAN1, CAN0 Connector............................................................................................................................. 15
X5 – Power Connector .................................................................................................................................................. 15
Expansion Connectors .................................................................................................................................................. 16
X2 – Expansion Connector 2.............................................................................................................................. 16
X1 – Expansion Connector 1.............................................................................................................................. 18
X3 – Expansion Connector 3.............................................................................................................................. 19
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.9.1
4.9.2
4.9.3
5
Switches, Jumper and LED Description............................................................................................................................ 21
5.1
S1 – Reset switch............................................................................................................................................................. 21
S2 – Ethernet Control Signals / SDCARD CS........................................................................................................... 21
S3 – UART Switch ............................................................................................................................................................ 21
S4 – Boot Configuration ............................................................................................................................................... 21
JP1 – Ethernet Speed Selection ................................................................................................................................. 21
JP2 -– Power Supply Jumper....................................................................................................................................... 21
JP3 – RTC Power Jumper.............................................................................................................................................. 21
JP4 – USB ID...................................................................................................................................................................... 22
S5 - Button......................................................................................................................................................................... 22
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10 General Purpose LEDs................................................................................................................................................... 22
5.11 Ethernet LEDs................................................................................................................................................................... 22
5.12 LEDs of the Debug Agent............................................................................................................................................. 22
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
2
6
7
Boot Mode Description .......................................................................................................................................................... 22
Installation.................................................................................................................................................................................. 23
7.1
7.2
Initial Board Setup .......................................................................................................................................................... 23
Debug Agent Setup (DEV-BF548DA-Lite only)..................................................................................................... 26
8
9
Using the VDSP Flash Programming Tool........................................................................................................................ 30
8.1
8.2
Developing an Application.......................................................................................................................................... 30
Overwriting BLACKSheep Code................................................................................................................................. 30
Extender Board Compatibility List...................................................................................................................................... 31
9.1
Without Extender Board............................................................................................................................................... 31
EXT-BF5xx-EXP................................................................................................................................................................. 31
EXT-BF5xx-Video............................................................................................................................................................. 31
Audio Extender Board................................................................................................................................................... 32
Camera Extender Board................................................................................................................................................ 32
Analog-Digital / Digital-Analog Converter Extender Board............................................................................. 32
USB-ETH Extender Board.............................................................................................................................................. 32
Video and Audio Extender Board.............................................................................................................................. 32
Camera and Audio Extender Board .......................................................................................................................... 33
Anomalies .............................................................................................................................................................................. 33
Product Changes ................................................................................................................................................................. 33
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
10
11
Document Revision History............................................................................................................................................................ 34
List of Figures and Tables ...................................................................................................................................................... 35
A
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
3
Packing List
The DEV-BF548DA-Lite and the DEV-BF548-Lite Board Package contain the following items:
1. DEV-BF548DA-Lite or DEV-BF548-Lite Board
2. 1x USB Cable (USB A/B)
3. 1x USB Cable (USB A/B) (DEV-BF548DA-Lite only)
4. 1x USB Cable (USB A/Mini USB)
5. 1x Ethernet Cable
6. 1x Power Supply.
7. Support CD
Note: The Core Modules are not shipped with the board, so you must order them separately.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
4
Edition 2008-09
© Bluetechnix Mechatronische Systeme GmbH 2008
All Rights Reserved.
The information herein is given to describe certain components and shall not be considered as a
guarantee of characteristics.
Terms of delivery and rights of technical change reserved.
We hereby disclaim any warranties, including but not limited to warranties of non-infringement,
regarding circuits, descriptions and charts stated herein.
Bluetechnix makes and you receive no warranties or conditions, express, implied, statutory or in any
communication with you. Bluetechnix specifically disclaims any implied warranty of merchantability or
fitness for a particular purpose.
Bluetechnix takes no liability for any damages and errors causing of the usage of this board. The user of
this board is responsible by himself for the functionality of his application. He is allowed to use the
board only if he has the qualification. More information is found in the General Terms and Conditions
(AGB).
Information
For further information on technology, delivery terms and conditions and prices please contact
Bluetechnix (http://www.bluetechnix.com).
Warning
Due to technical requirements components may contain dangerous substances.
The Core Modules and development systems
contain ESD (electrostatic discharge) sensitive
devices.
Electro-static
charges
readily
accumulate on the human body and
equipment and can discharge without
detection. Permanent damage may occur on
devices subjected to high-energy discharges.
Proper ESD precautions are recommended to
avoid performance degradation or loss of
functionality. Unused Core Modules and
Development Boards should be stored in the
protective shipping
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
5
BLACKFIN Products
Core Modules:
TCM-BF518:
The new Core Module CM-BF518 is powered by Analog Devices' single core
ADSP-BF518 processor; up to 400MHz, 32MB SDRAM, up to 8MB flash. The
2x60 pin expansion connectors are backwards compatible with other Core
Modules.
CM-BF527:
The new Blackfin Processor Module is powered by Analog Devices' single
core ADSP-BF527 processor; key features are USB OTG 2.0 and Ethernet. The
2x60 pin expansion connectors are backwards compatible with other Core
Modules.
CM-BF533:
Blackfin Processor Module powered by Analog Devices' single core ADSP-
BF533 processor; up to 600MHz, 32MB SDRAM, 2MB flash, 2x60 pin
expansion connectors and a size of 36.5x31.5mm.
TCM-BF537:
Blackfin Processor Module powered by Analog Devices' single core ADSP-
BF537 processor; up to 500MHz, 32MB SDRAM, 8MB flash, a size of
28x28mm, 2x60 pin expansion connectors, Ball Grid Array or Border Pads
for reflow soldering, industrial temperature range -40°C to +85°C.
CM-BF537E:
Blackfin Processor Module powered by Analog Devices' single core ADSP-
BF537 processor; up to 600MHz, 32MB SDRAM, 4MB flash, integrated
TP10/100 Ethernet physical transceiver, 2x60 pin expansion connectors and
a size of 36.5x31.5mm.
CM-BF537U:
CM-BF548:
CM-BF561:
eCM-BF561:
Blackfin Processor Module powered by Analog Devices' single core ADSP-
BF537 processor; up to 600MHz, 32MB SDRAM, 4MB flash, integrated USB
2.0 Device, 2x60 pin expansion connectors and a size of 36.5x31.5mm.
The new Blackfin Processor Module is powered by Analog Devices' single
core ADSP-BF548 processor; key features are 64MB DDR SD-RAM 2x100 pin
expansion connectors.
Blackfin Processor Module powered by Analog Devices' dual core ADSP-
BF561 processor; up to 2x 600MHz, 64MB SDRAM, 8MB flash, 2x60 pin
expansion connectors and a size of 36.5x31.5mm.
Blackfin Processor Module powered by Analog Devices' dual core ADSP-
BF561 processor; up to 2x 600MHz, 128MB SDRAM, 8MB flash, 2x100 pin
expansion connectors and a size of 44x33mm.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
6
Development Boards:
EVAL-BF5xx:
Low cost Blackfin processor Evaluation Board with one socket for any
Bluetechnix Blackfin Core Module. Additional interfaces are available, e.g.
an SD-Card.
DEV-BF5xxDA-Lite:
Get ready to program and debug Bluetechnix Core Modules with this tiny
development platform including an USB-Based Debug Agent. The DEV-
BF5xxDA-Lite is a low cost starter development system including a VDSP++
Evaluation Software License.
DEV-BF548-Lite:
Low-cost development board with one socket for Bluetechnix CM-BF548
Core Module. Additional interfaces are available, e.g. an SD-Card, USB and
Ethernet.
DEV-BF548DA-Lite:
Get ready to program and debug Bluetechnix CM-BF548 Core Module with
this tiny development platform including an USB-Based Debug Agent. The
DEV-BF548DA-Lite is a low-cost starter development system including a
VDSP++ Evaluation Software License.
EXT-Boards:
The following Extender Boards are available: EXT-BF5xx-AUDIO, EXT-BF5xx-
VIDEO, EXT-BF5xx-CAM, EXT-BF5xx-EXP-TR, EXT-BF5xx-USB-ETH2, EXT-
BF5xx-AD/DA, EXT-BF548-EXP and EXT-BF518-ETH. Furthermore, we offer
the development of customized extender boards for our customers.
Software Support:
BLACKSheep:
The BLACKSheep VDK is a multithreaded framework for the Blackfin
processor family from Analog Devices that includes driver support for a
variety of hardware extensions. It is based on the real-time VDK kernel
included within the VDSP++ development environment.
LabVIEW:
uClinux:
LabVIEW embedded support for Bluetechnix Core Modules is done by
Schmid-Engineering AG: http://www.schmid-engineering.ch
All the Core Modules are fully supported by uClinux. The required boot
loader and uClinux can be downloaded from: http://blackfin.uClinux.org.
Upcoming Products and Software Releases:
Keep up-to-date with all the changes to the Bluetechnix product line and software updates at:
http://www.bluetechnix.com .
BLACKFIN Design Service
Based on more than five years of experience with Blackfin, Bluetechnix offers development assistance as
well as custom design services and software development.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
7
1 Introduction
NOTE: The DEV-BF548DA-Lite has an on-board Debug Agent, which is not available on the DEV-BF548-
Lite Board. All other features are identical! In this document, when describing both boards, the name
DEV-BF548-Lite is used.
The DEV-BF548-Lite Development Board with integrated Debug Agent is designed as a development
and application board for the high performance ADSP-BF548 based CM-BF548 Core Module. Special
feature of the board is the 10/100Mbit industrial Ethernet controller. The integrated Debug Agent is a
USB based debug interface which enables programming and debugging of the Blackfin Core Modules.
It is fully compatible with the Visual DSP++ development environment. The development board
provides all interfaces on dedicated connectors or expansion connectors. Extender boards can be
plugged on top of the Development Board in order to enable additional interfaces.
1.1 Overview
The DEV-BF548-Lite Board includes the following components:
60 Pin Expansion Connector 1
DC/DC
Power Supply
(5V and 3V3)
USB to
UART
CM-BF548
DEBUG
USB-OTG
AGENT
64MB DDR SD RAM
8MB Flash
SD-Card
10/100Mbit
(Ethernet
CAN
Controller)
60 Pin Expansion Connector 2
Figure 1-1: Overview of the DEV-BF548-Lite Board
DC/DC Converters
o
5V@2A
o
3V3@1.5A (draws its power from the 5V output of the DC/DC)
1 Core Module Slot
o
Supports the CM-BF548 Core Module
USB-to-UART Port
o
o
o
Supports up to 915kbps UART-USB conversion.
Emulates a standard COM port on the computer.
Drivers for Windows and Linux available
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
8
JTAG
o
JTAG-Plug that supports all analog Devices JTAG Emulators.
Expansion Connector 1 (X1)
o
o
o
o
o
o
o
Data Bus
Address Bus
Memory Control
RESET
PPI0 (Parallel Port Interface 0)
GPIO (Programmable )
Power Supply
Expansion Connector 2 (X2)
o
o
o
o
o
PPI1 (Parallel Port Interface 1), SPORT1
Power Supply (Main Supply Connector)
GPIO (Programmable )
UART0
SPI2
Expansion Connector 3 (X3)
o
o
o
o
o
o
o
o
ATAPI Interface
SPI0, SPI1
SPORT2, SPORT3
CAN 0, CAN1
UART2, UART3
PPI0 (Sync, D16,D17))
SDIO Interface
GPIO (Programmable )
USB2.0 OTG Connector
o
Uses the On-Board USB-OTG transceiver
RJ-45 Ethernet Plug
o
Connected to the On-Board SMSC LAN9218 Ethernet Controller
External Power Supply
o
The board is shipped with a 12V, 2A external DC/DC Power Supply
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
9
2 Functional Specification
Figure 2-1: Functional Block Diagram
Power connector and Power supply:
The supplied power supply should be used. It can deliver up to 2A at 12V.
The input voltage range of an alternative power supply must be between 6-16V!
The on-board DC/DC power supply generates 5V and 3.3V which are made available at the expansion
connectors.
The maximum current that can be drawn from the 5V is 2A, but take care this includes the current going
into the 3.3V regulator also, because this regulator is powered by the 5V. The maximum current that can
be drawn from the 3.3V is 1.5A but note that this means at least 1A additional load on the 5V connector.
The serial Port 0 (UART0, default Console IO) or Port1 (UART1) of the Core Module can be routed directly
to the USB Port (USB/UART Switch (S3).
An Ethernet controller (SMSC LAN9218) is connected to the data and address bus on the baseboard
providing a high speed 10/100MBit LAN Interface
An SD-Card connector is mounted on the board and is connected to the processors SD-IO Interface. With
the SD-Card one can make use of file IO Functions delivered with the BLACKSheep Software.
BLACKSheep supports SD-Cards and includes a FAT file system as well as the most relevant File IO
Functions. The complete BLACKSheep software package can be purchased from Bluetechnix.
The USB2.0 OTG connector interfaces with the processors on-chip (ADSP-BF548) USB Transceiver.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
10
3 PCB Placement and Mechanical Outline
3.1 PCB Placement
X5
X7
X6
X13
X11
Power USB JTAG
Ext . JTAG
USB -OTG
USB -UART
S4
JP4
X12
1
0
1 0
S3
3
P
J
1 … 8
ON
2
P
J
1
1
X10 CAN 1
X8 CAN 0
X1
31 30
X2
S1
31 30
S2
1 … 4 0
1
60 1
60 1
80
41
40
X3
1
X9
1
P
J
SD-CARD
S5
X4 Ethernet JACK
Corner holes on Core Module indicating insertion Rotation
Figure 3-1: Connector PCB Placement
ATTENTION: Please mind the direction while inserting the Core Module!
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
11
3.2 Mechanical Outline
Figure 3-2: Mechanical Outline – Expansion Connector Placement
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
12
3.3 Extension Board Footprint
If you want to design your own Extension Board for the DEV-BF548, you can use the following Board
dimensions. The mating Connectors in Figure 3-3 are mounted on top.
Figure 3-3: Recommended Footprint for Extension Boards – top view
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
13
4 Connector Description
4.1 X4 –RJ45 Ethernet Connector
Pin No.
Signal (Core Module)
IO-Type
1
2
3
4
5
6
7
8
TX+
TX-
RX+
NC
NC
RX-
NC
NC
O
O
I
-
-
I
-
-
Table 4-1: Ethernet Connector
4.2 X9 –SD-Card Connector (bottom Mount)
Pin No.
Signal (Core Module)
Description (SD Card)
0
1
2
3
4
5
6
7
8
9
10
SD_D2
SD_D3
SD_CMD
GND
3,3V
SD_CLK
GND
SD_D0
SD_D1
-
DAT2
CD/DAT3
CMD
VSS1
VDD
CLK
VSS2
DAT0
DAT1
CD
-
WP
Table 4-2: SD-Card Connector
4.3 X6 – JTAG Bypass Connector
The JTAG connector is compliant with any Blackfin JTAG Emulator from Analog Devices. When an
external JTAG emulator is attached the on-board JTAG is bypassed and the external one is automatically
used.
4.4 X11 – USB-UART Connectors
Connects either UART0 (when S3 is in Pos 1) or UART1 (when S3 is in Pos 0) to the USB Interface
enabling a COM Port on the PC. UART0 is standard console IO for the BLACKSheep Software.
4.5 X12 UART Expansion Pads
When S3 is in position 1 the UART1 on PortH (TX, RX) is available on the expansion pins and
disconnected from the USB-UART Chip.
Pin No.
Signal
Signal Type
1
2
3
4
TxD Blackfin
RxD Blackfin
GND
Input Core Module
Output Core Module
3V3
Regulated Power
Table 4-3: UART1 additional Header
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
14
4.6 X1, X2, X3 Expansion Connectors
The Expansion Connectors on the DEV-BF548-Lite for a Stacked Height of 16mm are of the following
type:
Part
X1, X2
Manufacturer
AMP (Stacked Height = 16mm)
Manufacturer Part Nr.
5-5179010-2
Matching connector
X3
Matching connector
AMP
5179031-2
5-5179010-3
5179031-3
AMP (Stacked Height = 16mm)
AMP
Table 4-4: DEV-board connector types
The matching connector, which is used for building an extender board, can be ordered from
Bluetechnix.
4.7 X8, X10 – CAN1, CAN0 Connector
Pin No.
1
2
Signal (Core Module)
CAN+
CAN-
IO-Type
I/O
I/O
Table 4-5: CAN Connector
4.8 X5 – Power Connector
The board is shipped with a 12V, 2A external DC/DC Power Supply which should be used.
Pin No.
Signal
Description
1
2
3
Vin (+6V to +16V DC) Input Supply
NC
GND
Preferable 12V DC (2A)
Table 4-6: Power Supply
Figure 4-1: Power connector
To connect to X141 use a “DCPP1” e.g. from Cliff Electronic Components (2.1mm * 5.5mm * 9.5mm) plug
to the power supply. Outer contact is GND, inner contact is VCC.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
15
4.9 Expansion Connectors
The interface to the extender boards is grouped into three different connectors (X1, X2, X3). The three
tables below shows the pin out of these three connectors. The column “Pin No. (Connector)” shows the
pin number of each connector, while the column “Pin No. (Symbol) shows the pin number of the
extension connector schematic symbol, where the pins are numbered from 1 to 200. The column “Pin
No. CM” represents the pin number of the corresponding signal on the Core Module.
4.9.1 X2 – Expansion Connector 2
Pin
(Symbol)
1
2
3
4
5
6
7
No. Pin
(Connector)
No. Signal
Signal type
Pin No CM
1
2
3
4
5
6
7
8
PC7
PC6
PC3
PC2
CLKOUT
PE15
PA13
PA5
3.3V
3.3V
PD0
PD2
PD4
PD6
PD8
PD10
PD12
PD14
PH0
PE12
PB11
PB9
I/O
I/O
I/O
I/O
O
93
94
97
98
70
I/O
I/O
I/O
PWR
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
PWR
PWR
PWR
PWR
I/O
O
O
O
I/O
I/O
I/O
185
114
106
8
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
135
137
139
141
143
145
147
149
22
188
130
128
192
132
131
23
PE8
PB13
PB12
PH1
nARDY
PH4
5.0V *)
5.0V 2)
Vin 3)
Vin 3)
PH7
nAMS3
nABE1
nABE0
PB14
PE7
21
26
29
32
17
16
133
193
127
PB8
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
16
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
PB10
PE11
PE13
PD15
PD13
PD11
PD9
PD7
PD5
PD3
PD1
GND
GND
PA1
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
129
189
187
150
148
146
144
142
140
138
136
102
110
25
186
99
100
95
96
PA9
PH3
PE14
PC1
PC0
PC5
PC4
4-7 Expansion Connector X2
1) Maximum current carrying capacity: 1A.
2) Pin 29 and 30 of the X8 connector are +5V stabilized from the DC/DC that can be used for custom
add-on boards or the extender boards. Maximum current carrying capacity: 900mA.(Attention: If Core
Modules with USB in host mode are used, the current must be shared with the connected USB device.
3) Pin 31 and 32 of the X7 are Vin of the external power supply minus the input protection diode voltage.
These pins can be used for custom add-on board power supplies. Maximum current carrying capacity:
1A.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
17
4.9.2 X1 – Expansion Connector 1
Pin
(Symbol)
61
No. Pin
(Connector)
No. Signal
Signal type
Pin No CM
1
A1
O
1
62
2
A3
O
3
63
3
A5
O
5
64
4
A7
O
7
65
5
A9
O
9
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
6
7
8
9
A11
A13
A15
PG1
PG2
PF1
PF3
PF5
PF7
PF9
PF11
PF13
PF15
GND
nAMS1
nAWE
nNMI
D0
D2
D4
D6
D8
D10
D12
D14
D15
D13
D11
D9
D7
D5
D3
D1
nRESET
nAOE
nARE
nAMS2
3.3V
PF14
PF12
PF10
PF8
O
O
O
11
13
15
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
O
165
164
181
179
177
175
173
171
169
167
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
30
20
34
35
37
39
41
43
45
47
49
50
48
46
44
42
40
38
36
67
18
19
31
O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
98
99
100
101
102
103
104
105
106
107
O
O
PWR
I/O
I/O
I/O
I/O
168
170
172
174
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
18
108
109
110
111
112
113
114
115
116
117
118
119
120
48
49
50
51
52
53
54
55
56
57
58
59
60
PF6
PF4
PF2
PF0
PH2
PG0
A14
A12
A10
A8
A6
A4
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
176
178
180
182
24
166
14
12
10
8
6
4
2
O
O
A2
4-8 Expansion Connector X1
4.9.3 X3 – Expansion Connector 3
Pin No. (Symbol)
Pin
No. Signal
Signal type
Pin No CM
(Connector)
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
1
2
3
4
5
6
7
8
GND
PJ13
PJ12
PJ11
PJ10
PJ9
PJ8
PJ7
PJ6
PJ5
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
74
75
76
77
78
79
80
81
82
83
84
85
86
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PJ4
PJ3
PJ2
PJ1
GND
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
GND
PA0
PA2
PA3
PA4
PA6
PA7
PA8
PA10
119
120
121
122
123
124
125
126
101
103
104
105
107
108
109
111
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
19
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PA11
PA12
PA14
PA15
GND
GND
3.3V
3.3V
5.0V
Vin
GND
PG3
PG4
PG5
PG6
PG7
PG8
PG9
PG10
PG11
PG12
PG13
PG14
PG15
GND
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE9
PE10
GND
PC8
PC9
PC10
PC11
PC12
PC13
PH6
PH5
ATAPI_PDIAG
EXT_WAKEUP
GND
CLKBUF
GND
I/O
I/O
I/O
I/O
PWR
PWR
PWR
PWR
PWR
PWR
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
PWR
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
112
113
115
116
163
162
161
160
159
158
157
156
155
154
153
152
151
200
199
198
197
196
195
194
191
190
92
91
90
89
88
87
28
27
134
33
O
PWR
O
69
PWR
4-9 Expansion Connector X3
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
20
5 Switches, Jumper and LED Description
5.1 S1 – Reset switch
Performs system reset.
5.2 S2 – Ethernet Control Signals / SDCARD CS
Default Settings
Dipswitch
S2.1
Function
Connect SDCARD CS to PC5
S2.2
S2.3
S2.4
Connect nAMS1 from Core Module to Ethernet chip
Connect PE6 from Core Module to Ethernet chip IRQ
Connect PME of Ethernet chip to test point PME1
5-1 DIP switch S2
5.3 S3 – UART Switch
Move S3 to position 1 to route the Core Modules RX0 and TX0 signals to USB
Move S3 to position 0 to route the Core Modules RX1 and TX1 signals to USB
5.4 S4 – Boot Configuration
S4.1 to S4.4 Control the boot mode and are described in chapter 6 Boot Mode Description.
Dipswitch
S4.1
Function
Bootmode 0
S4.2
Bootmode 1
S4.3
Bootmode 2
S4.4
Bootmode 3
S4.5
S4.6
S4.7
S4.8
Power Supply for CAN0 Driver IC
Power Supply for CAN1 Driver IC
Connect TXD‐USB to VCC
Connect S5 to VCC
5-2 DIP switch S4
5.5 JP1 – Ethernet Speed Selection
Set jumper JP1 to select Ethernet Speed 10MBit/s and unset JP1 for 100Mbit/s.
5.6 JP2 -– Power Supply Jumper
This jumper can be removed in order to insert an AMPERE METER for current measurement:
5.7 JP3 – RTC Power Jumper
This jumper is used to connect the VddRTC pin of the Core Module to 3.3V. You can also use this jumper
to connect a battery to the internal RTC of the Blackfin.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
21
5.8 JP4 – USB ID
Short jumper JP4 to tie USB ID to GND on the USB-OTG Connector X13.
5.9 S5 - Button
The button S5 is a GPIO Button and connects to PH7.
5.10 General Purpose LEDs
Designator
V14
V15
Function
GPIO LED
GPIO LED
Blackfin GPIO
PH6
PH5
Table 5-3: Core Module LEDs
5.11 Ethernet LEDs
Designator
Color
Description
Fullduplex
Activity
V1
V2
V3
Yellow
Green
Green
100MB Speed LED
Table 5-4: Ethernet LEDs
5.12 LEDs of the Debug Agent
Designator
V9
V10
V11
V12
Color
Description
Flag0
Flag1
Monitor
Pr. done
Green
Green
Green
Green
Table 5-5: LEDs for the Debug Agent
6 Boot Mode Description
Boot-settings for CM-BF548 (S4) only Switches 1 – 4 of 8 are shown
The default Boot Mode option for the BLACKSheep Software is 0001 !
The default Boot Mode option for the uClinux / uBoot is 0001 !
BMODE3–0 (S4.4‐S4.1)
Description
0000
0001
0010
0011
0100
0101
0110
0111
Idle–no boot
Boot from 8‐ or 16‐bit external flash memory
Boot from 16‐bit asynchronous FIFO
Boot from serial SPI memory (EEPROM or flash)
Boot from SPI host device
Boot from serial TWI memory (EEPROM/flash)
Boot from TWI host
Boot from UART host
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
22
1000
1001
1010
1011
1100
1101
1110
1111
Reserved
Reserved
Boot from (DDR) SDRAM
Boot from OTP memory
Reserved
Boot from 8‐ or 16‐bit NAND flash memory via NFC
Boot from 16‐Bit Host DMA
Boot from 8‐Bit Host DMA
Table 6-1: Boot modes
7 Installation
7.1 Initial Board Setup
The installation guide is written for Windows (Windows 2000 and WinXP). However for connecting the
USB device the driver for MAC and LINUX are available on the CD.
In order to set up und test your DEV-BF548-Lite board the following steps can be done:
1. Make sure jumpers JP2 and JP3 are set and the Switch S3 is in Position 1. as shown in Figure 7-1
(JP1 unset).
Figure 7-1: Setup of the DEV-BF548-Lite Board
2. If you want to use an SD-Card, insert the SD-Card in the appropriate slot at the bottom side of
the board.
3. Connect the power supply to the power connector off the DEV-BF548-Lite board.
4. Connect the DEV-BF548-Lite Board via USB to the PC. The pre-flashed BLACKSheep starts and
the LED mounted on the DEV-BF548-Lite board starts blinking. On the PC usually the ‘Found
New Hardware Wizard’ opens.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
23
If the wizard asks you to connect to the windows update site, select “No, not this time”
Choose: “Install from a list or specific location”. The driver is located on your support CD.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
24
This procedure has to be done twice, because at first the USB driver will be installed. Then the
Hardware Wizard opens again, because the UART bridge driver has to be installed in addition
using the same driver file. Simply repeat this step.
5. Open the Windows device manager (Control Panel System Hardware) to see which COM
port number has been assigned to the CP2101 UART-to-USB Chip. This number differs from
computer to computer based on the already installed COM ports. (e.g. COM4)
6. Open a Terminal program like the HyperTerminal included in Windows operating systems and
open the respective COM port with 115200 Baud, 8 Data-bits, No Parity and 1 Stop bit,
disable the Hardware flow control.
7. Reset the DEV-BF548-Lite Board (Press the main reset button). After this you will see the
BLACKSheep boot-screen showing up. If you disconnect the device, you have to reconnect.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
25
This shows a sample boot screen. Depending on the current software version, you might get
different boot messages.
8. You can find a simple hello world program on your support CD or at the download section of
the product homepage. To start the sample program, type “xmr UART” on your terminal
program, then (Transfer Send file) select the appropriate file “UART.ldr” depending on your
Core Module, choose protocol “Xmodem” and send. After the download has finished type “exec
UART” for executing the sample program.
9. Press reset to return to the BLACKSheep command line.
7.2 Debug Agent Setup (DEV-BF548DA-Lite only)
If you have purchased a DEV-BF548DA-Lite board with the Debug Agent mounted on the bottom side
of the board you can use it to download and debug your software with the VDSP++ development
environment from Analog Devices. An evaluation version is included in the support CD or you can
download it from our website or the website from Analog Devices. Currently the Debug Agent works
only with version 4.5 of the VDSP++ IDE.
Note: The Core Module will get warm while in use.
Please follow the instructions for installing and configuring VDSP++ to work with the Debug Agent.
1. Install VDSP++4.5
2. If available install the latest update for VDSP++4.5. You can download updates from the Analog
Devices website.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
26
3. Configure VDSP++4.5 to support the DEV-BF548DA-Lite by starting the Installer from your
support CD. Once started you should see the following dialog.
Note: To run the installer the .net framework is required!
4. Select the Core Module that you have inserted in the socket of your DEV-BF548DA-Lite.
5. Press the “Install” button.
6. You should get the following message:
7. Be sure that the board is powered on!
8. Connect X4 (USB JTAG) with an USB cable to a free USB port on your PC.
9. The following dialog or a similar one should appear:
10. Choose “Install the software automatically”, press “Next” and follow the instructions on the
screen.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
27
After the install process you have to create a Platform using the Platform Wizard of the VDSP++. Please
follow the instructions to create a valid Platform for the Bluetechnix USB Debug Agent.
1. Open the VisualDSP++ Configurator from the start menu entry of VisualDSP++ 4.5.
2. Select “New…”
3. In the “Type” box select the Bluetechnix entry corresponding to the Core Module on your DEV-
BF548DA-Lite board.
4. Enter a Name for the Platform for example “Bluetechnix CM-BF537”.
5. Select “Ok”. The created platform should appear in the “Platforms” section of the “configurator”
window.
6. Press “Ok” to close the VisualDSP++ Configurator.
The last step is the creation of a VDSP++ debug session. Please follow the instructions below.
1. Open the “New Session Wizard” from the pulldown menu of the VDSP++ (SessionNew
Session) or press the “New Session” button on the “Sesson List” window that appears on
startup of VDSP++.
2. Select the processor corresponding to your Core Module and press “Next”.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
28
3. Select “EZ-KIT Lite” and press “Next”.
4. Select the platform that you have created with the VisualDSP++ Configurator and press “Finish”.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
29
Now the session is ready and VDSP++ should start with these settings. The Core Module on the DEV-
BF548DA-Lite is now ready for debugging.
For further information about the session wizard and the VDSP++ tools please refer to the VDSP++
manuals downloadable from the Analog Devices website.
If you change your Core Module on the DEV-BF548DA-Lite you have to reconfigure VDSP++ starting
with the install tool as described above.
8 Using the VDSP Flash Programming Tool
8.1 Developing an Application
If you are developing your own projects with the VDSP++ development tools using the JTAG provided
by Analog Devices you can use the flash programming tool included in the VDSP++ environment in
order to flash your program on the Core Module. You have to load the flash driver located on your EVAL
board support CD corresponding to the inserted Core Module.
8.2 Overwriting BLACKSheep Code
If you overwrite intentionally or unintentionally the section in the flash containing the
BLACKSheep code, you need a JTAG device and the VDSP++ flash tool to reprogram the flash.
Flashing the appropriate BLACKSheep loader file (*.ldr) located on the CD, reinstalls the
BLACKSheep code.
The examples, drivers and the BLACKSheep software are under
permanent development. Please refer to the download section of
www.bluetechnix.com to get the latest versions or updates.
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
30
9 Extender Board Compatibility List
This chapter points out the compatibility of the DEV-BF548-Lite and DEV-BF548DA-Lite with Core
Module and Extension Boards. Please refer to the Extender board and Core Module Hardware Manuals
for further information.
Legend:
OK
(OK)
NO
Full functional
Functional but not all features are available
Not functional
NG
NT
Functionality not guaranteed
Not tested yet
Limited
Limited
The following tables show possible board combinations:
9.1 Without Extender Board
Core Module
CM-BF548
OK
No Extender
Table 9-1: Used without Extender Board
9.2 EXT-BF5xx-EXP
Core Module
CM-BF548
NT
EXT-BF5xx-EXP
Table 9-2: Used with the Experimental Extender Board
All boards can be used in combination with the Experimental Extender Board
9.3 EXT-BF5xx-Video
Core Module
CM-BF548
NT
EXT-BF5xx-Video
Table 9-3: Used with the Video Extender Board
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
31
9.4 Audio Extender Board
Core Module
CM-BF548
EXT-BF5xx-Audio
NT
Table 9-4: Used with the Audio Extender Board
9.5 Camera Extender Board
Core Module
CM-BF548
NT
EXT-BF5xx-Camera
Table 9-5: Used with the Camera Extender Board
9.6 Analog-Digital / Digital-Analog Converter Extender Board
Core Module
CM-BF548
NT
EXT-BF5xx-AD/DA
Table 9-6: Used with the Analog-Digital / Digital-Analog Converter Extender Board
9.7 USB-ETH Extender Board
Core Module
CM-BF548
EXT-BF5xx-USB-ETH
NT
Table 9-7: Used with the USB-ETH Extender Board
9.8 Video and Audio Extender Board
Core Module
CM-BF548
EXT-BF5xx-Video
EXT-BF5xx-Audio
NT
NT
Table 9-8: Used with the Video and the Audio Extender Board
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
32
9.9 Camera and Audio Extender Board
Core Module
CM-BF548
EXT-BF5xx-Camera
EXT-BF5xx-Audio
NT
NT
Table 9-9: Used with the Camera and the Audio Extender Board
10 Anomalies
2
Missing pull up resistor on nBR -> workaround done
1
Missing pull up resistor on CMD_OD -> workaround done
Table 10-1: Anomalies on V1.0 boards
11 Product Changes
Version
Changes
V1.1
Bug Fix and Connector Replacement
Initial Board Version
V1.0
Table 11-1: Product Changes
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
33
Document Revision History
Version
Date
Document Revision
13
2010-06-23
2010-02-09
2009-02-04
Layout changes
12
Redesign of Manual
11
Caption for some tables added
Table 5-1 corrected
Table 6-1 S4.4-S4.1 added
10
9
2008-10-15
2008-09-23
2008-08-18
2008-07-01
2008-06-26
2008-05-29
2008-05-23
2008-04-01
2007-12-10
2007-12-09
Chapter 4.9: column Pin No. (Symbol) added
Extension Footprint added, Layout changed
English checked for grammar, spelling and clarity.
Change matching connector
Fixed naming of dipwitches and added missing ones
VDSP++ Version
8
7
6
5
4
Several changes
3
Extender Board Compatibility List
Minor Changes
2
1
Initial release of the document
Table 0-1: Revision History
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
34
A List of Figures and Tables
Figures:
Figure 1-1: Overview of the DEV-BF548-Lite Board........................................................ 8
Figure 2-1: Functional Block Diagram ............................................................................. 10
Figure 3-1: Connector PCB Placement............................................................................. 11
Figure 3-2: Mechanical Outline – Expansion Connector Placement................................ 12
Figure 3-3: Recommended Footprint for Extension Boards – top view........................... 13
Figure 7-1: Setup of the DEV-BF548-Lite Board............................................................. 23
Tables:
Table 4-1: Ethernet Connector.......................................................................................... 14
Table 4-2: SD-Card Connector ......................................................................................... 14
Table 4-3: UART1 additional Header............................................................................... 14
Table 4-4: DEV-board connector types ............................................................................ 15
Table 4-5: CAN Connector ............................................................................................... 15
Table 4-6: Power Supply................................................................................................... 15
4-7 Expansion Connector X2............................................................................................ 17
4-8 Expansion Connector X1............................................................................................ 19
4-9 Expansion Connector X3............................................................................................ 20
5-1 DIP switch S2 ............................................................................................................. 21
5-2 DIP switch S4 ............................................................................................................. 21
Table 5-3: Core Module LEDs.......................................................................................... 22
Table 5-4: Ethernet LEDs ................................................................................................. 22
Table 5-5: LEDs for the Debug Agent.............................................................................. 22
Table 6-1: Boot modes...................................................................................................... 23
Table 9-1: Used without Extender Board.......................................................................... 31
Table 9-2: Used with the Experimental Extender Board .................................................. 31
Table 9-3: Used with the Video Extender Board.............................................................. 31
Table 9-4: Used with the Audio Extender Board.............................................................. 32
Table 9-5: Used with the Camera Extender Board ........................................................... 32
Table 9-6: Used with the Analog-Digital / Digital-Analog Converter Extender Board ... 32
Table 9-7: Used with the USB-ETH Extender Board....................................................... 32
Table 9-8: Used with the Video and the Audio Extender Board ...................................... 32
Table 9-9: Used with the Camera and the Audio Extender Board.................................... 33
Table 10-1: Anomalies on V1.0 boards ............................................................................ 33
Table 11-1: Product Changes............................................................................................ 33
Table 0-1: Revision History.............................................................................................. 34
Blackfin DEV-BF548-Lite. DEV-BF548DA-lite Hardware User Manual
35
相关型号：
©2020 ICPDF网 联系我们和版权申明