DS1817R-10 [ETC]
Voltage Detector ; 电压检测器\n型号: | DS1817R-10 |
厂家: | ETC |
描述: | Voltage Detector
|
文件: | 总5页 (文件大小:75K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DS1817
Active High 3.3V EconoReset
www.dalsemi.com
FEATURES
ꢀ Automatically restarts a microprocessor after
power failure
PIN ASSIGNMENT
3
ꢀ Maintains reset for 150 ms after VCC returns
to an in-tolerance condition
ꢀ Reduces need for discrete components
ꢀ Precision temperature-compensated voltage
reference and voltage sensor
ꢀ Accurate 5%, 10% or 20% power monitoring
ꢀ 20% tolerance for use with 3.0-volt systems
ꢀ Low-cost TO-92 or space saving surface
mount SOT-23 packages available
ꢀ Push-pull active high output
1
2
SOT-23 PACKAGE
See Mech. Drawing
1 2 3
1 2 3
ꢀ Operating temperature -40°C to +85°C
TO-92 PACKAGE
See Mech. Drawing
PIN DESCRIPTION
TO-92
1
2
3
RST
VCC
GND
Active High Reset Output
Power Supply
Ground
SOT-23
1
2
3
RST
VCC
Active High Reset Output
Power Supply
Ground
GND
DESCRIPTION
The DS1817 EconoReset uses a precision temperature reference and comparator circuit to monitor the
status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail
signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition,
the reset signal is kept in the active state for approximately 150 ms to allow the power supply and
processor to stabilize.
1 of 5
111999
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS1817
OPERATION - POWER MONITOR
The DS1817 provides the function of detecting out-of-tolerance power supply conditions and warning a
processor based system of impending power failure. When VCC is detected as out-of-tolerance, the RST
signal is asserted. On power-up, RST is kept active for approximately 150 ms after the power supply has
reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST
is released.
BLOCK DIAGRAM (CMOS OUTPUT) Figure 1
APPLICATION EXAMPLE Figure 2
2 of 5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS1817
TIMING DIAGRAM: POWER-UP Figure 3
TIMING DIAGRAM: POWER-DOWN Figure 4
3 of 5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS1817
ABSOLUTE MAXIMUM RATINGS*
Voltage on VCC Pin Relative to Ground
Voltage on RST Relative to Ground
Operating Temperature
-0.5V to +7.0V
-0.5V to 5VCC +0.5V
-40°C to +85°C
Storage Temperature
Soldering Temperature
-55°C to +125°C
260°C for 10 seconds
* This is a stress rating only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS
(-40°C to +85°C)
PARAMETER
SYMBOL MIN
TYP
MAX
UNITS NOTES
Supply Voltage
VCC 0.0
5.5
V
1
DC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC=1.2V to 5.5V)
PARAMETER
SYMBOL MIN
TYP
MAX
UNITS NOTES
VOH
VCC
VCC
V
1
Output Voltage @ 0-500 µA
-0.5V -0.1V
Output Current @ 2.4V
Output Current @ 0.4V
Operating Current VCC < 5.5
VCC Trip Point (DS1817-5)
VCC Trip Point (DS1817-10)
VCC Trip Point (DS1817-20)
Output Capacitance
IOH
IOL
350
2
2
3
1
1
1
µA
mA
µA
V
+10
28
ICC
35
VCCTP
VCCTP
VCCTP
COUT
2.98
2.80
2.47
3.06
2.88
2.55
3.15
2.97
2.64
10
V
V
pF
AC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C; VCC=1.2V to 5.5V)
PARAMETER
SYMBOL MIN
TYP
150
2
MAX
250
5
UNITS NOTES
RESET Active Time
VCC Detect to RST
tRST
tRPD
tF
100
300
0
ms
µs
VCC Slew Rate
6
µs
(VCCTP (MAX) to VCCTP (MIN))
VCC Slew Rate
tR
ns
(VCCTP (MIN) to VCCTP (MAX))
VCC Detect to RST
tRPU
100
150
250
ms
4, 5
4 of 5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
DS1817
NOTES:
1. All voltages are referenced to ground.
2. Measured with VCC ≥ 2.7V.
3. Measured with RST output open.
4. Measured with 2.7V ≥ VCC ≥ 3.3V.
5. tR = 5 µs.
6. The tF value is for reference in defining values for TRPD and should not be considered a requirement
for proper operation or use of the device.
PART MARKING CODES
SOT-23 PACKAGE
“A”, “B”, &“C” represent the Device Type.
“D” represents the Device Tolerance.
810
811
812
813
815
816
817
818
-
-
-
-
-
-
-
-
DS1810
DS1811
DS1812
DS1813
DS1815
DS1816
DS1817
DS1818
A
B
C
D
-
-
-
-
5%
10%
15%
20%
5 of 5
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相关型号:
DS1817R-10+T&R
Power Supply Support Circuit, Fixed, 1 Channel, +2.88VV, CMOS, PDSO3, 0.50 INCH, ROHS COMPLIANT, SOT-23, 3 PIN
MAXIM
DS1817R-10-U
Power Supply Support Circuit, Fixed, 1 Channel, +2.88VV, CMOS, PDSO3, 0.50 INCH, SOT-23, 3 PIN
MAXIM
DS1817R-10-U+
Power Supply Support Circuit, Fixed, 1 Channel, +2.88VV, CMOS, PDSO3, 0.50 INCH, ROHS COMPLIANT, SOT-23, 3 PIN
MAXIM
DS1817R-10/T&R
Power Supply Support Circuit, Fixed, 1 Channel, +2.88VV, CMOS, PDSO3, 0.50 INCH, SOT-23, 3 PIN
MAXIM
DS1817R-20
Power Supply Support Circuit, Fixed, 1 Channel, +2.55VV, CMOS, PDSO3, SOT-23, 3 PIN
DALLAS
DS1817R-20+T&R
1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3, 0.50 INCH, ROHS COMPLIANT, SOT-23, 3 PIN
ROCHESTER
DS1817R-20/T&R
Power Supply Support Circuit, Fixed, 1 Channel, +2.55VV, CMOS, PDSO3, 0.50 INCH, SOT-23, 3 PIN
MAXIM
DS1817R-5+T&R
Power Supply Support Circuit, Fixed, 1 Channel, +3.06VV, CMOS, PDSO3, 0.50 INCH, ROHS COMPLIANT, SOT-23, 3 PIN
MAXIM
©2020 ICPDF网 联系我们和版权申明