DU66F-16D1 [ETC]
Delay Line ; 延迟线\n型号: | DU66F-16D1 |
厂家: | ETC |
描述: | Delay Line
|
文件: | 总4页 (文件大小:66K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DDU66F
Ò
5-TAP, TTL-INTERFACED
FIXED DELAY LINE
(SERIES DDU66F)
data
delay
devices,
3
inc.
FEATURES
PACKAGES
IN
VCC
1
4
14
12
10
8
·
·
·
·
·
Five equally spaced outputs
Fits standard 14-pin DIP socket
Low profile
Auto-insertable
Input & outputs fully TTL interfaced & buffered
1
2
3
4
5
6
7
14
13
12
11
10
9
VCC
N/C
T1
N/C
T3
N/C
T5
IN
N/C
N/C
T2
N/C
T4
T1
T2
T3
T4
6
7
GND
T5
8
GND
·
10 T2L fan-out capability
DDU66F-xx
DDU66F-xxA2 Gull-Wing
DDU66F-xxB2 J-Lead
DIP
DDU66F-xxD1
DDU66F-xxD4
DDU66F-xxMD1 Mil. SMD
DDU66F-xxMD4 Mil. SMD
Com. SMD
Com. SMD
DDU66F-xxME7 Military DIP
FUNCTIONAL DESCRIPTION
PIN DESCRIPTIONS
The DDU66F-series device is a 5-tap digitally buffered delay line. The
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
amount given by the device dash number. For dash numbers less than 25,
the total delay of the line is measured from T1 to T5, with the nominal value
given by the dash number. The nominal tap-to-tap delay increment is
IN
T1-T5 Tap Outputs
VCC +5 Volts
GND Ground
Signal Input
given by 1/4 of this number. The inherent delay from IN to T1 is nominally 3.5ns. For dash numbers
greater than or equal to 25, the total delay of the line is measured from IN to T5, with the nominal value
given by the dash number. The nominal tap-to-tap delay increment is given by 1/5 of this number.
DASH NUMBER SPECIFICATIONS
SERIES SPECIFICATIONS
Part
Number
DDU66F-4
DDU66F-6
Total
Delay Per
Tap (ns)
1.0 ± 0.5
1.5 ± 0.5
2.0 ± 1.0
2.5 ± 1.0
3.0 ± 1.0
4.0 ± 1.5
5.0 ± 1.5
5.0 ± 2.0
6.0 ± 2.0
7.0 ± 2.0
8.0 ± 2.0
9.0 ± 3.0
10.0 ± 3.0
12.0 ± 3.0
15.0 ± 3.0
20.0 ± 3.0
25.0 ± 3.0
30.0 ± 3.0
35.0 ± 4.0
40.0 ± 4.0
50.0 ± 5.0
·
·
·
·
Minimum input pulse width: 40% of total delay
Output rise time: 2ns typical
Supply voltage: 5VDC ± 5%
Supply current: ICCL = 32ma typical
ICCH = 7ma typical
Operating temperature: 0° to 70° C
Temp. coefficient of total delay: 100 PPM/°C
Delay (ns)
4 ± 1.0 *
6 ± 1.0 *
8 ± 2.0 *
10 ± 2.0 *
12 ± 2.0 *
16 ± 2.0 *
20 ± 3.0 *
25 ± 3.0
30 ± 3.0
35 ± 3.0
40 ± 3.0
45 ± 3.0
50 ± 3.0
60 ± 3.0
75 ± 4.0
100 ± 5.0
125 ± 6.5
150 ± 7.5
175 ± 8.0
200 ± 10.0
250 ± 12.5
DDU66F-8
DDU66F-10
DDU66F-12
DDU66F-16
DDU66F-20
DDU66F-25
DDU66F-30
DDU66F-35
DDU66F-40
DDU66F-45
DDU66F-50
DDU66F-60
DDU66F-75
DDU66F-100
DDU66F-125
DDU66F-150
DDU66F-175
DDU66F-200
DDU66F-250
·
·
3.5ns
25%
25%
25%
25%
VCC IN
T1
T2
T3
T4
T5 GND
Functional diagram for dash numbers < 25
20%
20%
20%
20%
20%
VCC IN
T1
T2
T3
T4
T5 GND
* Total delay is referenced to first tap output
Input to first tap = 3.5ns ± 1ns
Functional diagram for dash numbers >= 25
Ó1997 Data Delay Devices
NOTE: Any dash number between 4 and 250 not
Doc #97020
2/5/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
1
DDU66F
APPLICATION NOTES
Delay Devices if your application requires device
testing at a specific input condition.
HIGH FREQUENCY RESPONSE
The DDU66F tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 40% of the total delay and periods as
small as 80% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
POWER SUPPLY BYPASSING
The DDU66F relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VCC to GND,
located as close as possible to the VCC pin, is
recommended. A wide VCC trace and a clean
ground plane should be used.
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Supply Voltage
Input Pin Voltage
Storage Temperature
Lead Temperature
SYMBOL
VCC
VIN
TSTRG
TLEAD
MIN
-0.3
-0.3
-55
MAX
7.0
VCC+0.3
150
UNITS NOTES
V
V
C
300
C
10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
High Level Output Voltage
VOH
2.5
3.4
V
VCC = MIN, IOH = MAX
VIH = MIN, VIL = MAX
VCC = MIN, IOL = MAX
VIH = MIN, VIL = MAX
Low Level Output Voltage
VOL
0.35
0.5
V
High Level Output Current
Low Level Output Current
High Level Input Voltage
Low Level Input Voltage
Input Clamp Voltage
Input Current at Maximum
Input Voltage
High Level Input Current
Low Level Input Current
Short-circuit Output Current
Output High Fan-out
IOH
IOL
VIH
VIL
VIK
IIHH
-1.0
20.0
mA
mA
V
V
V
2.0
-60
0.8
-1.2
0.1
VCC = MIN, II = IIK
VCC = MAX, VI = 7.0V
mA
IIH
IIL
IOS
20
-0.6
-150
25
VCC = MAX, VI = 2.7V
VCC = MAX, VI = 0.5V
VCC = MAX
mA
mA
mA
Unit
Load
Output Low Fan-out
12.5
Doc #97020
2/5/97
DATA DELAY DEVICES, INC.
Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
2
DDU66F
PACKAGE DIMENSIONS
14
12
10
8
7
Lead Material:
Nickel-Iron alloy 42
TIN PLATE
14
12
10
8
7
.410
TYP.
1
4
6
1
4
6
.280
MAX.
.780 MAX.
.820 MAX.
.290
MAX.
.320
MAX.
.020
TYP.
.130
.015 TYP.
.070 MAX.
.030
±
.020 TYP.
.010 .002
±
.018
TYP.
.100
TYP.
.018 TYP.
.600 TYP.
.300
TYP.
.350
MAX.
.600 .010
±
DDU66F-xxME7 (Military)
DDU66F-xx (Commercial)
.020 TYP.
12
.040
TYP.
.010 TYP.
.040
TYP.
.020 TYP.
12
.050 TYP.
14
1
10
8
7
14
1
10
8
7
.320
TYP.
.270
TYP.
.430
TYP.
.270
TYP.
4
6
4
6
.090
.100
.300
MAX.
.110
.100
.350
MAX.
.110
TYP.
.050
TYP.
.600
.600
.790 MAX.
.790 MAX.
DDU66F-xxA2 (Commercial Gull-Wing)
DDU66F-xxB2 (Commercial J-Lead)
.650
.100
.017
.050
.100
1
7
14
8
.017
1
7
14
8
.510
MAX.
.300
TYP.
.510
MAX.
.300
TYP.
.100
.080
.050
.025
.100
.510 MAX.
.360 TYP.
.080
.300
.510 MAX.
.300
.008
.200 MAX. (Com)
.225 MAX. (Mil)
.200 MAX. (Com)
.225 MAX. (Mil)
.008
.045
.005
.065
.360
.065
.065 TYP.
.065 TYP.
TYP.
TYP.
TYP.
DDU66F-xxD1 (Commercial SMD)
DDU66F-xxMD1 (Military SMD)
DDU66F-xxD4 (Commercial SMD)
DDU66F-xxMD4 (Military SMD)
Doc #97020
2/5/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
3
DDU66F
DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT:
OUTPUT:
Ambient Temperature: 25oC ± 3oC
Supply Voltage (Vcc): 5.0V ± 0.1V
Load:
Cload
1 FAST-TTL Gate
5pf ± 10%
:
Input Pulse:
High = 3.0V ± 0.1V
Threshold: 1.5V (Rising & Falling)
Low = 0.0V ± 0.1V
Source Impedance:
Rise/Fall Time:
50W Max.
3.0 ns Max. (measured
between 0.6V and 2.4V )
PWIN = 1.5 x Total Delay
PERIN = 10 x Total Delay
Pulse Width:
Period:
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
PRINTER
COMPUTER
SYSTEM
REF
PULSE
GENERATOR
OUT
IN
T1
T2
T3
T4
T5
IN
TIME INTERVAL
COUNTER
DEVICE UNDER
TEST (DUT)
TRIG
TRIG
Test Setup
PERIN
PWIN
VIH
TRISE
TFALL
INPUT
SIGNAL
2.4V
1.5V
0.6V
2.4V
1.5V
0.6V
VIL
TRISE
TFALL
OUTPUT
SIGNAL
VOH
1.5V
1.5V
VOL
Timing Diagram For Testing
Doc #97020
2/5/97
DATA DELAY DEVICES, INC.
Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
4
相关型号:
©2020 ICPDF网 联系我们和版权申明