FF-47 [ETC]
Analog Miscellaneous ; 模拟杂项\nATTENUATORS, PIN DIODE
SERIES DF & FF
“PHASE-FREE” 0.25–18 GHz
GENERAL INFORMATION:
KDI/Triangle’s phase free Pin diode attenuators change the amplitude of
a microwave signal with matched (low) VSWR over the full attenuation
range, and with minimum phase shift change. The units are supplied with
either an analog or with a digital control input, with a dynamic attenuation
range of 32 dB minimum. Standard digital units are supplied with 8 TTL
logic inputs (bits) and therefore can produce 256 discrete values of atten-
uation. Units with 10 or 12 bits can be provided as specials.
GENERAL SPECIFICATIONS:
Frequenc y Range:
RF Impedance:
D.C. Voltage:
0.25 to 18.0 GHz
50 OHMS
± 15 volts at ± 50 mA
Logic: (DF Series)
No. of Bits:
TTL compatible
8 L.S.B. = 0.125 dB.
Attentuation:
31.875 dB
Control Rang e: (FF Series)
0-10 volts produces 0-32 dB. Other control
voltages can be provided on request.
10 K Ohms, 20 pf
Notes:
Control Input Impedance
1. Harmonic Distortion: Approximately –50 dBc for Pin ≤ 0 dBm at a frequen-
cy of 1.0 GHz for most units. This value improves by approximately 10 dB
per octave as the frequency increases; however, since this value is depen-
dent on bandwidth of the unit, power input, and switching speed required,
the factory should be consulted if harmonic content is an important system
requirement.
2. The phase shift over the center half of the frequency range is 1/2 of the
value listed, e.g.: the phase shift of the FF-47 is ±5° from 2.5 to 3.5 GHz
(0–20 dB). See Fig. 2
Accurac y/Frequenc y Flatness
For octave models, the frequency sensi-
tivity including digital settability is typically ±
0.8 dB to 20 dB; ± 1.25 dB to 32 dB over
the frequency range. Narrow band units are
proportionally more accurate.
100 mW CW 60 watts peak operational.
Units will not be damaged by application of
1 watt CW 100 watts peak.
Operating temperature from -55°C to +85°C
A) Standard: ±0.3 dB from + 10°C to +40°C
B) ± 0.5 dB to 20 dB and ±0.75 dB to 32 dB
can be provided from -54°C to +85°C. If this
stability is desired, add a suffix TT to model
number.for example, if the DF-74 is desired
with temperature compensation, it is
ordered as DF-74-TT.
RF Power:
Temperature Inf ormation:
Temperature Stability:
3. Other configurations (up to 12 Bits) or units with different attenuation
values can be quoted on request.
.32
.38
[8,2]
[9,7]
TYP
A/2
TYP
F
Connector s:
SMA standard. A mating multipin connector
can be supplied with each unit upon request.
ITT Cannon MDB-1-15SSL or equivilent.
Response time of all models is 10
microsec. Faster models (to 150
nanosec.) can be quoted on request.
Any of the models “FF” can be supplied
with a linearizer by adding a prefix 2. For
example, if the FF-47 is desired with a
linearizer, it is ordered as a 2-FF-47.The
overall accuracy including linearity and
frequency sensitivity is then ±0.75 dB to
20 dB and ±1.25 dB to 32 dB.
PIN #1
REF
B
D
Switching Speed:
Linearization:
E
.56
[14,2]
.20
[5,0]
C
.10
[2,5]
A
ITT CANNON
MDB1-15PSP
OR EQUIV.
.125/[3,20] DIA THRU
3 MTG HOLES
DIGITAL MODELS (DF SERIES)
Out-
Line
A
B
C
D
E
F
G
POWER LOGIC PIN CONNECTIONS
in[mm]
in[mm]
in[mm]
in[mm]
in[mm]
in[mm]
in[mm]
1
2
3
4
5
6
4.00[101,6] 4.00[10,1]
3.00[76,2] 2.00[50,8]
4.00[101,6] 2.00[50,8]
3.600[91,4]
2.600[66,04]
3.600[91,4]
3.375[85,72] 0.38[9,65] 0.39[9,90] 0.32[8,12]
PIN
1-12
13
14
15
FUNCTION
Logic inputs
+15 VDC
-15 VDC
GND
1.375[34,92] 0.35[8,9]
3.375[85,72] 0.45[11,4]
0.25[6,4] 0.32[8,12]
0.25[6,4] 0.34[8,6]
4.50[114,3] 4.00[101,6] 4.100[104,14] 3.375[85,72] 0.31[7,87] 0.31[7,87]
3.50[88,9] 2.00[50,8] 3.100[78,74] 1.375[34,92] 0.40[10,2] 0.28[7,11]
4.50[114,3] 2.00[50,8] 4.100[104,14] 1.375[34,92] 0.45[11,4] 0.25[6,4]
—
—
—
KEY: Inches[Millimeters] .XX .03 .XXX .010 [.X 0.8 .XX 0.25]
60 South Jefferson Road, Whippany, NJ 07981
Tel: 973-887-8100 • Fax: 973-884-0445
E-Mail: kdisales@aol.com
TRIANGLE
An MCE Company
C O R P O R A T I O N
10/98
See us on the web @ www.kditriangle.com
ATTENUATORS, PIN DIODE
SERIES DF & FF
“PHASE-FREE” 0.25–18 GHz
SPECIFICATIONS
DF Series
Least
Significant
Bit dB
Note 3
.125
VSWR
Insertion
Loss
Maximum
dB
For All
Values of
Atten.
Maximum Phase
Digital
Model*
No.
Analog
Model
No.
Frequency
Range
GHz
Atten.
Range
Maximum dB
Shift
Deg.
FF
Outline
1
DF
Outline
4
Maximum
0–20 dB
10
20–32 dB
FF-18
DF-18
0.25–0.5
32
4.5
1.5
15
FF-32
FF-36
FF-45
FF-47
FF-62
FF-73
FF-74
DF-32
DF-36
DF-45
DF-47
DF-62
DF-73
DF-74
0.95–1.25
1.0–2.0
1.7–2.4
2.0–4.0
4.0–8.0
7.0–12.4
8.0–18.0
1
3
3
3
2
2
2
4
6
6
6
5
5
5
.125
.125
.125
.125
.125
.125
.125
32
32
32
32
32
32
32
3.0
4.0
1.5
1.5
1.5
1.5
1.75
1.8
2.2
5
7.5
15
10
15
15
15
20
10
6
3.5
3.0
10
12
12
15
3.75
4.25
5.5
* Add Prefix “2” for Linearization
Add Suffix “TT” for Temp Comp; -55 to +85Њc
0.38
[09,7]
TYP.
TYPICAL CURVE OF ATTENUATION
VS CONTROL VOLTAGE
A/2
G
FIG. 1
32
30
0.125[3,18] DIA THRU
3 MTG. HOLES
F
0.5 dB
NON
LINEARIZED
GND
NOTE:EITHER
RF CONNECTOR
MAY BE USED
FOR INPUT
-15V
+15V
25
20
15
10
5
B
D
CON-
TROL
SMA
FEMALE
TYP.
E
LINEARIZED
.56[14,22]
C
A
0.10[2,5]
0.20[5,1]
BEST FIT
STRAIGHT
LINE
ANALOG MODELS (FF SERIES)
+15
TYPICAL CURVE OF FF-18 OR DF-18
AT MAX. ATTENUATION (32 dB)
0
+12
+9
0
2
5
8
10
CONTROL VOLTAGE
(V)
TYPICAL CURVE OF FF-45 OR DF-45
AT MAX. ATTENUATION (32 dB)
+6
+3
TYPICAL CURVE OF FF-18 OR DF-18
AT 20 dB ATTENUATION
0
-3
TYPICAL CURVE OF FF-45 OR DF-45
AT 20 dB ATTENUATION
-6
-9
REF. PHASE AT ZERO ATTENUATION
FOR FF-18 OR DF-18 AND FF-45 OR DF-45
-12
-15
F0
Fmax
Fmin
FREQUENCY
PHASE SHIFT VS FREQUENCY
AT VARIOUS ATTENUATION LEVELS
KEY: Inches[Millimeters] .XX .03 .XXX .010 [.X 0.8 .XX 0.25]
60 South Jefferson Road, Whippany, NJ 07981
Tel: 973-887-8100 • Fax: 973-884-0445
E-Mail: kdisales@aol.com
TRIANGLE
An MCE Company
C O R P O R A T I O N
10/98
See us on the web @ www.kditriangle.com
相关型号:
©2020 ICPDF网 联系我们和版权申明