FT24C16A-UPG-T [ETC]
Two-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide);型号: | FT24C16A-UPG-T |
厂家: | ETC |
描述: | Two-Wire Serial EEPROM 4K, 8K and 16K (8-bit wide) 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 |
文件: | 总20页 (文件大小:322K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
24C04A, 24C08A, 24C16A
Two-Wire Serial EEPROM
4K, 8K and 16K (8-bit wide)
FEATURES
Low voltage and low power operations:
FT24C04A/08A/16A: VCC = 1.8V to 5.5V
Maximum Standby current < 1µA (typically 0.02µA and 0.06µA @ 1.8V and 5.5V respectively).
16 bytes page write mode.
Partial page write operation allowed.
Internally organized: 512 8 (4K), 1024 8 (8K), 2048 8 (16K).
Standard 2-wire bi-directional serial interface.
Schmitt trigger, filtered inputs for noise protection.
Self-timed Write Cycle (5ms maximum).
1 MHz (5V), 400 kHz (1.8V, 2.5V, 2.7V) Compatibility.
Automatic erase before write operation.
Write protect pin for hardware data protection.
High reliability: typically 1, 000,000 cycles endurance.
100 years data retention.
Industrial temperature range (-40o C to 85o C).
Standard 8-pin DIP/SOP/TSSOP/DFN/MSOP and 5-pin SOT-23/TSOT-23 Pb-free packages.
DESCRIPTION
The FT24C04A/08A/16A series are 4096/8192/16384 bits of serial Electrical Erasable and Programmable Read Only
Memory, commonly known as EEPROM. They are organized as 512/1024/2048 words of 8 bits (1 byte) each. The
devices are fabricated with proprietary advanced CMOS process for low power and low voltage applications. These
devices are available in standard 8-lead DIP, 8-lead SOP, 8-lead TSSOP, 8-lead DFN, 8-lead MSOP, and 5-lead SOT-
23/TSOT-23 packages. A standard 2-wire serial interface is used to address all read and write functions. Our
extended VCC range (1.8V to 5.5V) devices enables wide spectrum of applications.
PIN CONFIGURATION
Pin Name
A2, A1, A0
SDA
Pin Function
Device Address Inputs
Serial Data Input / Open Drain Output
Serial Clock Input
SCL
WP
Write Protect
NC
No-Connect
© 2009 Fremont Micro Devices Inc.
DS3001M-page1
24C04A, 24C08A, 24C16A
All these packaging types come in conventional or Pb-free certified.
FT24C04A/08A/16A
FT24C04A/08A/16A
1
2
3
4
8
7
6
5
A0
A1
VCC
WP
1
2
3
5
4
WP
SCL
GND
SDA
A2
SCL
SDA
VCC
GND
8L DIP
SOT-23-5
8L SOP
TSOT-23-5
8L TSSOP
8L DFN
8L MSOP
ABSOLUTE MAXIMUM RATINGS
Industrial operating temperature:
Storage temperature:
-40oC to 85oC
-50oC to 125oC
Input voltage on any pin relative to ground:
Maximum voltage:
-0.3V to VCC + 0.3V
8V
ESD protection on all pins:
>2000V
* Stresses exceed those listed under “Absolute Maximum Rating” may cause permanent damage to the device.
Functional operation of the device at conditions beyond those listed in the specification is not guaranteed. Prolonged
exposure to extreme conditions may affect device reliability or functionality.
DS3001M-page2
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
PIN DESCRIPTIONS
(A) SERIAL CLOCK (SCL)
The rising edge of this SCL input is to latch data into the EEPROM device while the falling edge of this clock is to
clock data out of the EEPROM device.
(B) DEVICE / CHIP SELECT ADDRESSES (A2, A1, A0)
These are the chip select input signals for the serial EEPROM devices. Typically, these signals are hardwired to
either VIH or VIL. If left unconnected, they are internally recognized as VIL. FT24C04A has A0 pin as no-connect.
FT24C08A has both A0 and A1 pins as no-connect. For FT24C16A, all device address pins (A0-A2) are no-
connect.
(C) SERIAL DATA LINE (SDA)
SDA data line is a bi-directional signal for the serial devices. It is an open drain output signal and can be wired-
OR with other open-drain output devices.
(D) WRITE PROTECT (WP)
The FT24C04A/08A/16A devices have a WP pin to protect the whole EEPROM array from programming.
Programming operations are allowed if WP pin is left un-connected or input to VIL. Conversely all programming
functions are disabled if WP pin is connected to VIH or VCC. Read operations is not affected by the WP pin’s input
level.
Table A
Chip Select/Device
Address Pins Used
Max number of similar
devices on the same bus
Device
No-Connect Pins
FT24C04A
FT24C08A
FT24C16A
A2, A1
A2,
A0
4
2
1
A1, A0
(None)
A2, A1, A0
MEMORY ORGANIZATION
The FT24C04A/08A/16A devices have 32/64/128 pages respectively. Since each page has 16 bytes, random word
addressing to FT24C04A/08A/16A will require 9/10/11 bits data word addresses respectively.
DEVICE OPERATION
(A) SERIAL CLOCK AND DATA TRANSITIONS
The SDA pin is typically pulled to high by an external resistor. Data is allowed to change only when Serial clock
SCL is at VIL. Any SDA signal transition may interpret as either a START or STOP condition as described below.
(B) START CONDITION
With SCL VIH, a SDA transition from high to low is interpreted as a START condition. All valid commands
must begin with a START condition.
© 2009 Fremont Micro Devices Inc.
DS3001M-page3
24C04A, 24C08A, 24C16A
(C) STOP CONDITION
With SCL VIH, a SDA transition from low to high is interpreted as a STOP condition. All valid read or write
commands end with a STOP condition. The device goes into the STANDBY mode if it is after a read command.
A STOP condition after page or byte write command will trigger the chip into the STANDBY mode after the self-
timed internal programming finish.
(D) ACKNOWLEDGE
The 2-wire protocol transmits address and data to and from the EEPROM in 8 bit words. The EEPROM
acknowledges the data or address by outputting a "0" after receiving each word. The ACKNOWLEDGE signal
occurs on the 9th serial clock after each word.
(E) STANDBY MODE
The EEPROM goes into low power STANDBY mode after a fresh power up, after receiving a STOP bit in read
mode, or after completing a self-time internal programming operation.
Figure 1: Timing diagram for START and STOP conditions
SCL
SDA
START
Data
Data
STOP
Condition
Condition
Valid Transition
Figure 2: Timing diagram for output ACKNOWLEDGE
START Condition
SCL
Data in
Data out
ACK
DS3001M-page4
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
DEVICE ADDRESSING
The 2-wire serial bus protocol mandates an 8 bits device address word after a START bit condition to invoke valid read
or write command. The first four most significant bits of the device address must be 1010, which is common to all
serial EEPROM devices. The next three bits are device address bits. These three device address bits (5th, 6th and 7th) are
to match with the external chip select/address pin states. If a match is made, the EEPROM device outputs an
ACKNOWLEDGE signal after the 8th read/write bit, otherwise the chip will go into STANDBY mode. However,
matching may not be needed for some or all device address bits (5th, 6th and 7th) as noted below. The last or 8th bit is a
read/write command bit. If the 8th bit is at VIH then the chip goes into read mode. If a “0” is detected, the device enters
programming mode.
FT24C04A uses A2 (5th) and A1 (6th) device address bits. Only four FT24C04A devices can be wired-OR on the same
2-wire bus. Their corresponding chip select address pins A2 and A1 must be hard wired and coded from 00 (b) to 11
(b). Chip select address pin A0 is not used.
FT24C08A uses only A2 (5th) device address bit. Only two FT24C08A devices can be wired-OR on the same 2-wire
bus. Their corresponding chip select address pin A2 must be hard-wired and coded from 0 (b) to 1 (b). Chip select
address pins A1 and A0 are not used.
FT24C16A does not use any device address bit. Only one FT24C16A device can be used on the on 2-wire bus. Chip
Select address pins A2, A1, and A0 are not used.
WRITE OPERATIONS
(A) BYTE WRITE
A byte write operation starts when a micro-controller sends a START bit condition, follows by a proper EEPROM
device address and then a write command. If the device address bits match the chip select address, the EEPROM
device will acknowledge at the 9th clock cycle. The micro-controller will then send the rest of the lower 8 bits word
address. At the 18th cycle, the EEPROM will acknowledge the 8-bit address word. The micro-controller will then
transmit the 8 bit data. Following an ACKNOWLDEGE signal from the EEPROM at the 27th clock cycle, the
micro-controller will issue a STOP bit. After receiving the STOP bit, the EEPROM will go into a self-timed
programming mode during which all external inputs will be disabled. After a programming time of TWC, the byte
programming will finish and the EEPROM device will return to the STANDBY mode.
(B) PAGE WRITE
A page write is similar to a byte write with the exception that one to sixteen bytes can be programmed along the
same page or memory row. All FT24C04A/08A/16A are organized to have 16 bytes per memory row or page.
With the same write command as the byte write, the micro-controller does not issue a STOP bit after sending the
1st byte data and receiving the ACKNOWLEDGE signal from the EEPROM on the 27th clock cycle. Instead it
sends out a second 8-bit data word, with the EEPROM acknowledging at the 36th cycle. This data sending and
EEPROM acknowledging cycle repeats until the micro-controller sends a STOP bit after the n 9th clock cycle.
After which the EEPROM device will go into a self-timed partial or full page programming mode. After the page
programming completes after a time of TWC, the devices will return to the STANDBY mode.
© 2009 Fremont Micro Devices Inc.
DS3001M-page5
24C04A, 24C08A, 24C16A
The least significant 4 bits of the word address (column address) increments internally by one after receiving each
data word. The rest of the word address bits (row address) do not change internally, but pointing to a specific
memory row or page to be programmed. The first page write data word can be of any column address. Up to 16
data words can be loaded into a page. If more then 16 data words are loaded, the 17th data word will be loaded to
the 1st data word column address. The 18th data word will be loaded to the 2nd data word column address and so on.
In other word, data word address (column address) will “roll” over the previously loaded data.
(C) ACKNOWLEDGE POLLING
ACKNOWLEDGE polling may be used to poll the programming status during a self-timed internal programming.
By issuing a valid read or write address command, the EEPROM will not acknowledge at the 9th clock cycle if the
device is still in the self-timed programming mode. However, if the programming completes and the chip has
returned to the STANDBY mode, the device will return a valid ACKNOWLEDGE signal at the 9th clock cycle.
READ OPERATIONS
The read command is similar to the write command except the 8th read/write bit in address word is set to “1”. The three
read operation modes are described as follows:
(A) CURRENT ADDRESS READ
The EEPROM internal address word counter maintains the last read or write address plus one if the power supply
to the device has not been cut off. To initiate a current address read operation, the micro-controller issues a
START bit and a valid device address word with the read/write bit (8th) set to “1”. The EEPROM will response
with an ACKNOWLEDGE signal on the 9th serial clock cycle. An 8-bit data word will then be serially clocked out.
The internal address word counter will then automatically increase by one. For current address read the micro-
controller will not issue an ACKNOWLEDGE signal on the 18th clock cycle. The micro-controller issues a valid
STOP bit after the 18th clock cycle to terminate the read operation. The device then returns to STANDBY mode.
(B) SEQUENTIAL READ
The sequential read is very similar to current address read. The micro-controller issues a START bit and a valid
device address word with read/write bit (8th) set to “1”. The EEPROM will response with an ACKNOWLEDGE
signal on the 9th serial clock cycle. An 8-bit data word will then be serially clocked out. Meanwhile the internally
address word counter will then automatically increase by one. Unlike current address read, the micro-controller
sends an ACKNOWLEDGE signal on the 18th clock cycle signaling the EEPROM device that it wants another byte
of data. Upon receiving the ACKNOWLEDGE signal, the EEPROM will serially clocked out an 8-bit data word
based on the incremented internal address counter. If the micro-controller needs another data, it sends out an
ACKNOWLEDGE signal on the 27th clock cycle. Another 8-bit data word will then be serially clocked out. This
sequential read continues as long as the micro-controller sends an ACKNOWLEDGE signal after receiving a new
data word. When the internal address counter reaches its maximum valid address, it rolls over to the beginning of
the memory array address. Similar to current address read, the micro-controller can terminate the sequential read
by not acknowledging the last data word received, but sending a STOP bit afterwards instead.
(C) RANDOM READ
Random read is a two-steps process. The first step is to initialize the internal address counter with a target read
address using a “dummy write” instruction. The second step is a current address read.
To initialize the internal address counter with a target read address, the micro-controller issues a START bit first,
follows by a valid device address with the read/write bit (8th) set to “0”. The EEPROM will then acknowledge.
The micro-controller will then send the address word. Again the EEPROM will acknowledge. Instead of
sending a valid written data to the EEPROM, the micro-controller performs a current address read instruction to
read the data. Note that once a START bit is issued, the EEPROM will reset the internal programming process and
continue to execute the new instruction - which is to read the current address.
DS3001M-page6
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
© 2009 Fremont Micro Devices Inc.
DS3001M-page7
24C04A, 24C08A, 24C16A
Figure 8: SCL and SDA Bus Timing
AC CHARACTERISTICS
1.8 V
Min
2.5-5.0 V
Symbol
Parameter
Unit
Max
Min
Max
Clock frequency, SCL
Clock pulse width low
Clock pulse width high
Noise suppression time(1)
Clock low to data out valid
400
1000
kHz
µs
fSCL
tLOW
tHIGH
tI
1.3
0.6
0.4
0.4
µs
ns
µs
180
0.9
120
0.3
1.3
0.2
0.5
0.55
tAA
Time the bus must be free before a
new transmission can start(1)
µs
tBUF
START hold time
START set-up time
Data in hold time
Data in set-up time
Input rise time(1)
Input fall time(1)
0.6
0.6
0
0.25
0.25
0
µs
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tR
µs
µs
100
100
ns
0.3
0.3
µs
300
100
ns
tF
STOP set-up time
Date out hold time
Write cycle time
0.6
50
0.25
50
µs
tSU.STO
tDH
ns
ms
WR
5
5
Endurance(1) 25oC, Page Mode, 3.3V
1,000,000
Write Cycles
Notes: 1. This Parameter is expected by characterization but are not fully screened by test.
2. AC Measurement conditions:
RL (Connects to Vcc): 1.3KΩ
Input Pulse Voltages: 0.3Vcc to 0.7Vcc
Input and output timing reference Voltages: 0.5Vcc
DS3001M-page8
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
DC CHARACTERISTICS
Symbol
Parameter
Test Conditions
Min
Typical
Max
Units
VCC1
ICC
1.8
5.5
1.0
V
mA
mA
µA
µA
µA
µA
µA
V
24CA supply VCC
Supply read current
Supply write current
Supply current
V
V
V
V
V
CC @ 5.0V SCL = 400 kHz
CC @ 5.0V SCL = 400 kHz
CC @ 1.8V, VIN = VCC or VSS
CC @ 2.5V, VIN = VCC or VSS
CC @ 5.0V, VIN = VCC or VSS
0.5
2.0
ICC
3.0
ISB1
ISB2
ISB3
IIL
1.0
Supply current
1.0
Supply current
0.07
1.0
Input leakage current
VIN = VCC or VSS
3.0
ILO
Output leakage current VIN = VCC or VSS
Input low level
3.0
VIL
VIH
VOL1
VOL2
-0.6
VCC 0.3
VCC + 0.5
0.2
Input high level
VCC0.7
V
Output low level
Output low level
V
CC @ 1.8V, IOL = 0.15 mA
CC @ 3.0V, IOL = 2.1 mA
V
V
0.4
V
© 2009 Fremont Micro Devices Inc.
DS3001M-page9
24C04A, 24C08A, 24C16A
ORDER CODE:
FT24CXXA – XXX - X
Packaging
B: Tube
T: Tape and Reel
Temperature Range
U: -40 to 85 oC
Package
D: DIP
S: SOP
Option
M: MSOP
T: TSSOP
L: SOT23
P: TSOT23
N: DFN
G: Green Package RoHS Compliant
R: RoHS Compliant
ORDER INFORMATION
Order code
Temperature
Range
Vcc
Package
Option
Packaging
FT24C04A-UDG-B
FT24C04A-UDR-B
FT24C04A-USG-B
FT24C04A-USG-T
FT24C04A-USR-B
FT24C04A-USR-T
FT24C04A-UTG-B
Green Package
RoHS
Tube
Tube
Tube
T/R
DIP8
Green Package
Green Package
RoHS
SOP8
Tube
T/R
RoHS
Green Package
Green Package
RoHS
Tube
T/R
1.8v-5.5v
-40-850C
FT24C04A-UTG-T
FT24C04A-UTR-B
FT24C04A-UTR-T
FT24C04A-ULG-T
FT24C04A-ULR-T
FT24C04A-UPG-T
FT24C04A-UPR-T
TSSOP8
Tube
T/R
RoHS
Green Package
RoHS
T/R
SOT23-5
T/R
Green Package
RoHS
T/R
TSOT23-5
T/R
DS3001M-page10
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
ORDER INFORMATION(CONTINUED)
Temperature
Order code
Vcc
Package
Option
Packaging
Range
FT24C08A-UDG-B
FT24C08A-UDR-B
FT24C08A-USG-B
FT24C08A-USG-T
FT24C08A-USR-B
FT24C08A-USR-T
FT24C08A-UTG-B
FT24C08A-UTG-T
FT24C08A-UTR-B
FT24C08A-UTR-T
FT24C08A-ULG-T
FT24C08A-ULR-T
FT24C08A-UPG-T
FT24C08A-UPR-T
FT24C16A-UDG-B
FT24C16A-UDR-B
FT24C16A-USG-B
FT24C16A-USG-T
FT24C16A-USR-B
FT24C16A-USR-T
FT24C16A-UTG-B
FT24C16A-UTG-T
FT24C16A-UTR-B
FT24C16A-UTR-T
FT24C16A-ULG-T
FT24C16A-ULR-T
FT24C16A-UPG-T
FT24C16A-UPR-T
Green Package
RoHS
Tube
Tube
Tube
T/R
DIP8
Green Package
Green Package
RoHS
SOP8
Tube
T/R
RoHS
Green Package
Green Package
RoHS
Tube
T/R
TSSOP8
Tube
T/R
RoHS
Green Package
RoHS
T/R
SOT23-5
TSOT23-5
DIP8
T/R
Green Package
RoHS
T/R
1.8v-5.5v
-40-850C
T/R
Green Package
RoHS
Tube
Tube
Tube
T/R
Green Package
Green Package
RoHS
SOP8
Tube
T/R
RoHS
Green Package
Green Package
RoHS
Tube
T/R
TSSOP8
Tube
T/R
RoHS
Green Package
RoHS
T/R
SOT23-5
T/R
Green Package
RoHS
T/R
TSOT23-5
T/R
© 2009 Fremont Micro Devices Inc.
DS3001M-page11
24C04A, 24C08A, 24C16A
DIP8 PACKAGE OUTLINE DIMENSIONS
Dimensions In Millimeters
Symbol
Dimensions In Inches
Min
3.710
0.510
3.200
0.380
Max
Min
0.146
0.020
0.126
0.015
Max
A
A1
A2
B
4.310
0.170
3.600
0.570
0.142
0.022
B1
C
1.524(BSC)
0.060(BSC)
0.100(BSC)
0.204
9.000
6.200
7.320
0.360
9.400
6.600
7.920
0.008
0.354
0.244
0.288
0.014
0.370
0.260
0.312
D
E
E1
e
2.540 (BSC)
L
3.000
8.400
3.600
9.000
0.118
0.331
0.142
0.354
E2
DS3001M-page12
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
SOP8 PACKAGE OUTLINE DIMENSIONS
Dimensions In Millimeters
Dimensions In Inches
Min
Max
Min
Max
Symbol
A
A1
A2
b
1.350
0.100
1.350
0.330
0.170
4.700
3.800
5.800
1.750
0.250
1.550
0.510
0.250
5.100
4.000
6.200
0.053
0.004
0.053
0.013
0.006
0.185
0.150
0.228
0.069
0.010
0.061
0.020
0.010
0.200
0.157
0.244
c
D
E
E1
e
1.270 (BSC)
0.050 (BSC)
L
0.400
0°
1.270
8°
0.016
0°
0.050
8°
θ
© 2009 Fremont Micro Devices Inc.
DS3001M-page13
24C04A, 24C08A, 24C16A
TSSOP8 PACKAGE OUTLINE DIMENSIONS
Dimensions In Millimeters
Symbol
Dimensions In Inches
Min
2.900
4.300
0.190
0.090
6.250
Max
3.100
4.500
0.300
0.200
6.550
1.100
1.000
0.150
Min
0.114
0.169
0.007
0.004
0.246
Max
0.122
0.177
0.012
0.008
0.258
0.043
0.039
0.006
D
E
b
c
E1
A
A2
A1
e
0.800
0.020
0.031
0.001
0.65 (BSC)
0.25 (TYP)
0.026 (BSC)
0.01 (TYP)
L
0.500
1°
0.700
0.020
1°
0.028
7°
H
θ
7°
MSOP8 PACKAGE OUTLINE DIMENSIONS
DS3001M-page14
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
Dimensions In Millimeters
Dimensions In Inches
Symbol
Min
0.820
0.020
0.750
0.250
0.090
2.900
Max
1.100
0.150
0.950
0.380
0.230
3.100
Min
Max
0.043
0.006
0.037
0.015
0.009
0.122
A
A1
A2
b
0.320
0.001
0.030
0.010
0.004
0.114
c
D
e
0.65 (BSC)
0.026 (BSC)
E
2.900
4.750
0.400
0°
3.100
5.050
0.800
6°
0.114
0.187
0.016
0°
0.122
0.199
0.031
6°
E1
L
θ
DFN8 PACKAGE OUTLINE DIMENSIONS
© 2009 Fremont Micro Devices Inc.
DS3001M-page15
24C04A, 24C08A, 24C16A
Dimensions In Millimeters
Symbol
Nom
0.75
0.02
0.25
0.20
2.00
Min
0.70
-
Max
0.80
0.05
0.03
0.25
2.10
A
A1
b
0.18
0.18
1.90
c
D
D2
1.50REF
0.50BSC
1.50BSC
3.00
e
Nd
E
2.90
3.10
E2
1.60REF
0.40
L
0.30
0.20
0.50
0.30
0.25
h
L/F Surface Electroplate
Dimension(mil)
NIPdAu (Nickel, Pd, Metal)
67*75
DS3001M-page16
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
SOT-23-5 PACKAGE OUTLINE DIMENSIONS
Dimensions In Millimeters
Symbol
Dimensions In Inches
Min
Max
1.250
0.100
1.150
0.500
0.200
3.020
1.700
2.950
Min
Max
0.049
0.004
0.045
0.020
0.008
0.119
0.067
0.116
A
A1
A2
b
1.050
0.000
1.050
0.300
0.100
2.820
1.500
2.650
0.041
0.000
0.041
0.012
0.004
0.111
0.059
0.104
c
D
E
E1
e
0.95 (BSC)
0.037 (BSC)
e1
L
1.800
0.300
0°
2.000
0.600
8°
0.071
0.012
0°
0.079
0.024
6°
© 2009 Fremont Micro Devices Inc.
DS3001M-page17
24C04A, 24C08A, 24C16A
TSOT-23-5 PACKAGE OUTLINE DIMENSIONS
Dimensions In Millimeters
Symbol
Dimensions In Inches
Min
Max
Min
Max
A
A1
A2
b
0.700
0.000
0.700
0.350
0.080
2.820
1.600
2.650
0.900
0.100
0.800
0.500
0.200
3.020
1.700
2.950
0.028
0.000
0.028
0.014
0.003
0.111
0.063
0.104
0.035
0.004
0.031
0.020
0.008
0.119
0.067
0.116
c
D
E
E1
e
0.95 (BSC)
1.90 (BSC)
0.037 (BSC)
0.075 (BSC)
e1
L
0.300
0°
0.600
8°
0.012
0°
0.024
8°
DS3001M-page18
© 2009 Fremont Micro Devices Inc.
24C04A, 24C08A, 24C16A
© 2009 Fremont Micro Devices Inc.
DS3001M-page19
24C04A, 24C08A, 24C16A
Information furnished is believed to be accurate and reliable. However, Fremont Micro
Devices.,Ltd.(FMD) assumes no responsibility for the consequences of use of such information or for
any infringement of patents of other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent rights of Fremont Micro Devices.,Ltd.(FMD).
Specifications mentioned in this publication are subject to change without notice. This publication
supersedes and replaces all information previously supplied. Fremont Micro Devices.,Ltd.(FMD)
products are not authorized for use as critical components in life support devices or systems without
express written approval of Fremont Micro Devices.,Ltd.(FMD).
The FMD logo is a registered trademark of Fremont Micro Devices.,Ltd.
All other names are the property of their respective owners
©2007Fremont Micro Devices.,Ltd.-All rights reserved
www.fremontmicro.com
DS3001M-page20
© 2009 Fremont Micro Devices Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明