KHX18C10T3K4-16 [ETC]
DDR3-1866 CL10 240-Pin DIMM Kit;
| 型号： | KHX18C10T3K4-16 |
| 厂家： | 
ETC |
| 描述： | DDR3-1866 CL10 240-Pin DIMM Kit 双倍数据速率 |
| 文件： | 总2页 (文件大小：686K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
KHX18C10T3K2/8
8GB (4GB 512M x 64-Bit x 2 pcs.)
DDR3-1866 CL10 240-Pin DIMM Kit
SPECIFICATIONS
CL(IDD)
11 cycles
Row Cycle Time (tRCmin)
48.125ns (min.)
260ns (min.)
Refresh to Active/Refresh
Command Time (tRFCmin)
Row Active Time (tRASmin)
Maximum Operating Power
UL Rating
35ns (min.)
3.480 W* (per module)
94 V - 0
Operating Temperature
Storage Temperature
0o C to 85o C
-55o C to +100o C
*Power will vary depending on the SDRAM used.
DESCRIPTION
FEATURES
Kingston's KHX18C10T3K2/8 is a kit of two 512M x 64-bit
(4GB) DDR3-1866 CL10 SDRAM (Synchronous DRAM) 1Rx8
memory modules, based on eight 512M x 8-bit DDR3 FBGA
components per module. Each module kit supports Intel® XMP
(Extreme Memory Profiles). Total kit capacity is 8GB. Each
module kit has been tested to run at DDR3-1866 at a low
latency timing of 10-11-10 at 1.5V. The SPDs are programmed
to JEDEC standard latency DDR3-1600 timing of 11-11-11 at
1.5V. Each 240-pin DIMM uses gold contact fingers and
requires +1.5V. The JEDEC standard electrical and mechanical
specifications are as follows:
• JEDEC standard 1.5V (1.425V ~1.575V) Power Supply
• VDDQ = 1.5V (1.425V ~ 1.575V)
• 800MHz fCK for 1600Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 11, 10, 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
XMP TIMING PARAMETERS
• JEDEC: DDR3-1600 CL11-11-11 @1.5V
• XMP Profile #1: D3-1866 CL10-11-10 @1.5V
• XMP Profile #2: D3-1600 CL9-9-9 @1.5V
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.827” (46.41mm) w/ heatsink, single sided
component
Continued >>
kingston.com/hyperx
Document No. 4806975-001.A00 02/14/14 Page 1
continued
HyperX
MODULE DIMENSIONS
T
E C H N O L O G Y
133.35
Units: millimeters
30.00
18.80
15.80
11.00
8.00
0.00
MODULE WITH HEAT SPREADER
FOR MORE INFORMATION, GO TO WWW.KINGSTON.COM/HYPERX
All Kingston products are tested to meet our published specifications. Some motherboards or system configurations may not operate at
the published HyperX memory speeds and timing settings. Kingston does not recommend that any user attempt to run their computers
faster than the published speed. Overclocking or modifying your system timing may result in damage to computer components.
kingston.com/hyperx
Document No. 4806975-001.A00
Page 2
相关型号：
©2020 ICPDF网 联系我们和版权申明