LC700_技术文档

Installation

Instructions

LC700

LC750

Patient Care Unit with

Standard Laminate or

Optional Terreon®

Lavatory Top

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . .2

Installation Instructions

WARNING

Unpacking the Patient Care Unit . . . . . . . . . .3

Installing the Anchors . . . . . . . . . . . . . . . . . . .4

Water Closet and Waste Connections . . . . . . .5

Installing the Inline Backflow Preventer . . . .6

Installing the Cabinet . . . . . . . . . . . . . . . . . . .6

Installing the Terreon® Lav Top . . . . . . . . . . .6

Installing the Faucet and Water Supply . . . . .7

Completing Connections . . . . . . . . . . . . . . . . .8

Installing the Cabinet Floor and Back Panel .8

Installing the Door Linkage . . . . . . . . . . . . . .9

Cleaning and Maintenance . . . . . . . . . . . . . . . .10

Before beginning installation, all supply,

drain and waste piping to the unit must

be completed according to the rough-ins

received prior to receiving the unit. If

you have not received rough-ins, contact

your Bradley representative.

All mounting hardware provided is

essential for proper anchoring. Bradley

Corporation cannot assume any

responsibility for personal injury or

damage to equipment due to an

improperly installed unit.

Flush all water supply lines before

beginning installation.

This installation manual covers all

instructions for the LC700 or LC750

series including those with Terreon® Lav

tops. Omit any steps that do not apply to

the model you are installing.

Figures shown in this manual illustrate a

right-hand model. A left-hand model

would be opposite to what is shown.

Product warranties may be found under

“Product Information” on our web site at

www.bradleycorp.com.

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY FAX: (262) 251-5817

http://www.bradleycorp.com

215-1171 Rev. D; EN 04-1037

Page 1 of 10 8/16/04

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Pre-Installation Information

Overview

The Bradley LC700 and LC750 Patient Care Units are all-in-one units containing a water closet and

®

lavatory. The units come with either a laminate or Terreon lavatory top and may include an

optional flexible bedpan washer, inline backflow preventer and/or dialysis box.

Check contents

Separate all parts from packaging and make sure all parts are accounted for before discarding any

packaging material. If any parts are missing, do not attempt to install your Bradley Patient Care Unit

until you obtain the missing parts.

NOTE: The LC700 and LC750 Patient Care Units are shipped assembled (except for faucet-mount

option) and secured to a false plywood floor like it will be installed at your location. DO NOT

DISCARD PLYWOOD FLOOR! The plywood floor will serve as your anchor hole location

template.

NOTE: Before beginning installation, all supply, drain and waste piping to your Bradley Patient

Care Unit must be completed according to rough-ins received prior to receiving the unit. If you have

not received rough-ins, contact your Bradley representative.

Supplies required for installation:

• Steel angles and hardware for anchoring the water closet (if concrete is lightweight or less

than 4" thick)

• Hardware for waste outlet connections

• Shims (for water closet or cabinet installation, if necessary)

• Supply piping (including 1/2" NPT flexible hoses) to water closet, faucet or foot valve,

and bedpan washer

• Waste outlet piping to water closet

• P-trap and drain piping

• Silicone caulk

2

8/16/04

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

LINKAGE

BRACKET

Step 1: Unpack the Patient Care Unit

1. Remove the packaging around the Patient Care Unit.

2. Remove the door linkage by removing the nut fastened

on the linkage bracket (see Figure 1). Note the location

of the rod on the linkage bracket.

3. Lift out the trim piece around the water closet on the

cabinet floor (see Figure 2).

4. Unfasten the two panel clips and slide the sliding back

panel so that the panel lips unlock (see Figure 2). Bring

the panel out of the front of the cabinet.

DOOR

LINKAGE

ARM

Figure 1

5. Remove the cabinet floor by removing the two screws

holding the floor in place and sliding the

cabinet floor out.

SLIDING BACK

6. Remove the flexible hose, hose clamp,

inlet nut and pipe from the water closet

(see Figure 3).

PANEL

CLIP

STATIONARY

BACK PLATE

7. Unbolt the water closet and cabinet

assembly from the floor/template. Discard

the shipping hardware for the water closet

and cabinet, but DO NOT discard the

plywood floor/template.

HOSE CLAMP

PIPE

TRIM

PIECE

FLEXIBLE

HOSE

CABINET

FLOOR

CABINET FLOOR

SCREWS

INLET NUT

Figure 2

Figure 3

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

8/16/04

3

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

Step 2: Install the anchors

NOTE FOR OPTIONAL FOOT

VALVE: It is recommended that

floor anchors be used to secure the

foot valve to the floor (anchors and

appropriate hardware supplied by

installer).

1. Select the location where the

patient care unit is to be

installed. Using the supplied

template, lay out the hole

pattern for the water closet

and cabinet anchor locations

(see Figure 4).

NOTE FOR OPTIONAL FOOT

VALVE: Use the foot valve as a

template and lay out the anchor

locations on the floor. Drill

Figure 4

appropriate holes for two anchors.

2. Using a 5/8" concrete drill bit, drill four 2-1/8"

deep holes into the water closet support

anchoring locations using the template (see

Figure 4). Holes must be clean and free of

debris.

3. Using a 3/8" concrete drill bit, drill four 1-1/8"

deep holes into the cabinet anchoring locations

using the template (see Figure 4). Holes must be

clean and free of debris.

NOTE: If the floor concrete is lightweight or less

than 4" thick, Bradley recommends through-bolting

to steel angles under the floor (hardware supplied by

installer) (see Figure 7 on page 5).

Figure 5

NOTE FOR OPTIONAL FOOT VALVE: Install

appropriate anchors into the floor for foot valve

anchoring.

4. Remove the template. Drive the four 2-1/8"

anchors provided into the drilled holes for the

water closet using a hammer and the setting tool

supplied. The anchor should be driven in flush

with the floor (see Figure 5).

5. Drive the four 1/8" anchors provided into the

drilled holes for the cabinet using a hammer and

the setting tool. Make sure the anchors are

driven in flush with the floor (see Figure 6).

Figure 6

4

8/16/04

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

Step 3: Install the water closet and waste connections

1. Place the water closet over the water closet support

anchors installed in Step 2 on page 4.

2. Using the gasket supplied, connect the water closet to

the floor waste outlet (gaskets supplied by installer)

(see Figure 8).

NOTE: If the waste outlet is through the back or side

wall, use a no-hub type connector (available as an option)

but DO NOT tighten the connector (see Figure 9).

3. Square the water closet to the back wall. Level and

support the water closet solidly at the four corners

using shims (supplied by installer) if necessary.

4. Secure the water closet to the four floor anchors

using the 1/2" hex screws and washers supplied and

tighten securely (see Figure 8).

Figure 7

5. On patient care units with a back waste connection,

tighten the connector clamps at this time.

Figure 8

Figure 9

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

8/16/04

5

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

Step 4: Install the inline backflow preventer (for volume control or foot control)

1. Install the supplied inline backflow preventer to the wall

per local code.

2. Connect the water supply to the inlet of the foot valve (or

volume control valve, based on option supplied).

NOTE The foot valve inlet is located on the backside of the

valve.

3. Connect the outlet of the foot valve (or volume control

valve, based on option supplied) to the inlet of the

backflow preventer.

NOTE The foot valve outlet is located on the topside of the

valve.

4. Connect the outlet of the backflow preventer to the inlet of

Figure 10

the flexible hose.

Step 5: Install the cabinet

1. Install the supplied mounting studs into the

cabinet anchors installed in Step 2 on page 4.

2. Over each mounting stud, screw on a leveling

nut and place a washer over the nut (see Figure

10).

3. With the cabinet floor removed, locate the

cabinet in place over the mounting studs (see

Figure 10).

4. Add a flat washer and securing nut to each

cabinet mounting stud. Level the cabinet and

tighten the nuts.

NOTE FOR OPTIONAL FOOT VALVE: Install the

foot valve with the screws provided to the foot valve

anchors (installed in Step 2 on page 4) and tighten.

Figure 11

5. Connect the flexible hose, hose clamp, pipe and inlet nut to the water closet as shown in Figure 3

on page 3. Hand-tighten the inlet nut.

6. Connect the flexible hose to the flush valve (see Figure 11).

6

8/16/04

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

BEAD OF

CAULK

Step 5a: Install the optional

Terreon lavatory top

BEAD OF

CAULK

®

1. Apply a bead of silicone caulk around

the outer top edge of the cabinet and

between the lavatory top and the wall.

2. Set the lavatory top in place on the

cabinet making sure the back and wall

sides are flush with the edge of the

cabinet (see Figure 12).

3. Clean up any excess caulk.

Figure 12

Step 6: Install faucet and connect

water supply

FOOT VALVE MODELS (see Figures 13 and 14)

GOOSENECK

SPOUT

1. Place the faucet onto the countertop, gently inserting the faucet

supply shank through the hole provided in the lavatory bowl.

2. Using the washer and wingnut provided, mount the faucet to the

countertop by tightening the wingnut on the faucet's supply

shank.

LAVATORY

BOWL

3. Connect the flexible supply hose provided from the foot pedal

valve to the supply shank.

SUPPLY

SHANK

4. Connect the hot and cold water supply (piping supplied by

installer) to the 1/2” NPT inlet connectors on the foot valve (see

Figure 14).

SUPPLY

HOSE

Figure 13

FAUCET VALVE MODELS (see Figure 15)

1. Place the faucet onto the countertop, gently inserting the faucet supply shanks through the

holes provided in the lavatory bowl.

HOT

INLET

SUPPLY

2. Using the washers and wingnuts provided, mount

HOSE

the faucet to the countertop by tightening the

FOOT VALVE

COLD

INLET

wingnut on the faucet's supply shanks.

OUTLET

CONNECTION

3. Connect the hot and cold water supply (piping

supplied by installer) to the 1/2” NPT inlet

connectors on the foot valve.

Figure 15

FOOT VALVE

INLET

CONNECTORS

LAVATORY

BOWL

FOOT

VALVE

Figure 14

WASHER

WINGNUT

1/2” NPT

HOT INLET

1/2” NPT

COLD INLET

COUNTERTOP

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

8/16/04

7

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

Step 7: Completing Installation

1. Connect the flush valve water supply pipe to the flush valve 1" NPT inlet.

2. Install the strainer and tailpiece.

3. Install the P-trap (supplied by installer) to the sink drain, then connect the P-trap to the drain

pipe (piping supplied by installer).

Step 8: Reinstall the cabinet floor and back panel

1. Reinstall the cabinet floor and secure it to the cabinet frame with the two screws provided (see

Figure 16).

NOTE FOR OPTIONAL FOOT VALVE: The outlet hose must be positioned in the cabinet floor cutout

as shown in Figure 16.

2. Lay the trim piece around the base of the water closet on the cabinet floor (see Figure 16).

3. Using silicone caulk (supplied by installer), caulk between the trim piece and cabinet floor, and

caulk the gap between the pedestal and trim piece (see Figure 16).

4. Reinstall the back panel by bringing the sliding back panel in from the front of the module and

sliding the back panel into place.

5. Secure the back panel by sliding the back panel onto the frame corner (see Figure 17).

SLIDING BACK

PEDESTAL

TO SPOUT

PANEL

CLIP

STATIONARY

BACK PLATE

TRIM

PIECE

CAULK

TRIM

PIECE

CABINET FLOOR

SCREWS

CABINET

FLOOR

FOOT PEDAL

OUTLET HOSE

Figure 16

Figure 17

8

8/16/04

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Installation Instructions continued . . .

Step 9: Reinstall and adjust the door linkage

1. Reinstall the door linkage by loosely fastening the door linkage rod with the supplied nut onto

the linkage bracket (see Figure 18).

2. Close the door. If the water closet contacts the back wall before the door closes, adjust the door

linkage by turning the door linkage rod so that the door closes before the water closet comes in

contact with the back wall (see Figure 18). If no adjustment is needed, tighten the nut securely

on the linkage bracket.

NOTE: The linkage arm has a factory-set length. When the door linkage is fastened to the linkage

bracket, the door will open 110 degrees. If the PATIENT CARE UNIT is installed against a corner

wall, make sure the door does not come in contact with the wall, or the water closet does not come in

contact with the back wall when the door is opened or closed. Make adjustments, if necessary, and

refer to Figure 18 with inset.

3. After the adjustments are made, tighten the nut securely on the linkage arm.

DOOR

LINKAGE

BRACKET

2nd hole for 110 °

opening

3rd hole for 90 °

opening

DOOR

LINKAGE

ARM

Figure 18

Bradley Corporation • 215-1171 Rev. D; EN 04-1037

8/16/04

9

Patient Care Unit with Standard Laminate or Optional Terreon® Top

LC700, LC750

Installation Instructions

Patient Care Unit Cleaning and Maintenance

®

Regular cleaning greatly prolongs the service life of Terreon , stainless steel and laminate fixtures and, at

the same time, helps to maintain a pleasing surface appearance. The amount and frequency of cleaning

depends on the service conditions involved. For best results, fixtures should be cleaned as often as films or

deposits become apparent. This will remove built-up deposits which may eventually cause concentration

cells to set on the surface.

CAUTION: USING CLEANERS THAT CONTAIN HARSH CHEMICALS, ABRASIVES, ACIDS

OR DISINFECTANTS, OR CLEANING WITH STEEL WOOL OR BRUSHES, WILL RESULT IN

DAMAGE TO ALL SURFACES. IF THESE CHEMICALS COME IN CONTACT WITH ANY

SURFACE, WIPE OFF THE SURFACE IMMEDIATELY AND FLUSH WITH SOAPY WATER.

ALWAYS READ THE LABEL ON ANY CLEANING PRODUCT BEFORE APPLYING TO ANY

FIXTURE.

Terreon® cleaning

®

• Daily cleaning: Wipe the Terreon with a wet cloth, then rinse with clear water and wipe dry.

®

• Weekly cleaning: Give the Terreon surface a thorough cleaning with a damp cloth and a

household liquid detergent or ammonia-based cleaner. Most stains can be removed by cleaning the

®

Terreon surface with a mild abrasive cleaner, then rinsing and allowing to dry. Stubborn stains

can be cleaned as follows:

1. using a #7448 Scotch-Brite™ pad, scrub with an abrasive cleanser and water

2. clean thoroughly with clean soap and water and allow to dry

• Scorch marks: Although Terreon will not burn, a lit cigarette in contact with the Terreon

®

material could leave a scorch mark. Scorch marks can be removed with either an abrasive cleaner

or by buffing with a #7448 Scotch-Brite™ pad.

®

• Repair kit: A repair kit is available from Bradley to repair/patch Terreon . Contact your Modular

Services representative to order a repair kit and be sure to specify color when ordering.

Stainless steel and laminate cleaning

• Give the laminate surface a thorough cleaning with a non-abrasive liquid tub-and-tile cleaner to

remove soil and maintain the glossy finish.

You may safely use the following cleaners:

®

Formula 409

Spic and Span Powder

Liquid Comet

Glass Plus

Mr. Clean

®

Soft Scrub

Windex

DO NOT use the following:

®

Whitecap

Lysol Disinfectant Spray Lestoil

Pinesol

®

Dow Disinfectant Bathroom Cleaner

acetone, alcohol or steel wool/brushes

• Remove all material and deposits that tend to adhere to the laminate surface, taking special note of

crevices and corners

• Remove all material and deposits that tend to adhere to the stainless steel surface with stainless

steel polishing powder (always rub in the direction of the polishing lines)

• Check for rust spots or streaks on the stainless steel surface and look for the source of the rust (a

steel nail located in some iron or steel not actually a part of the stainless steel fixture may be the

cause). Rinse the laminate and stainless steel surfaces thoroughly and dry completely after

washing.

10

8/16/04

Bradley Corporation • 215-1171 Rev. D; EN 04-1037


型号：	LC700
厂家：	ETC
描述：	Patient Care Unit Standard Laminate or Optional Terreon?? Lavatory Top 病人护理单位标准强化或可选Terreon ？厕所顶部
文件：	总10页 (文件大小：197K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

LC700 [ETC]

相关型号：

LC700Z

LC701

LC7010

LC7020AK

LC7020AT

LC7020BK

LC7020BT

LC7030

LC70301LG/KLG/W

LC703200AW

LC703200AW-8C99-H

LC703831-300