LP2986ILDX-3.0 [ETC]
Fixed & Adjustable Voltage Regulator ; 固定和可调电压稳压器\n型号: | LP2986ILDX-3.0 |
厂家: | ETC |
描述: | Fixed & Adjustable Voltage Regulator
|
文件: | 总17页 (文件大小:441K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
January 2002
LP2986
Micropower, 200 mA Ultra Low-Dropout Fixed or
Adjustable Voltage Regulator
General Description
The LP2986 is a 200 mA precision LDO voltage regulator
which offers the designer a higher performance version of
the industry standard LP2951.
Features
n Ultra low dropout voltage
n Guaranteed 200 mA output current
n SO-8 and mini-SO8 surface mount packages
™
<
1 µA quiescent current when shutdown
n Low ground pin current at all loads
Using an optimized VIP (Vertically Integrated PNP) pro-
n
cess, the LP2986 delivers superior performance:
@
Dropout Voltage: Typically 180 mV 200 mA load, and 1
n 0.5% output voltage accuracy (“A” grade)
n High peak current capability (400 mA typical)
n Wide supply voltage range (16V max)
n Overtemperature/overcurrent protection
n −40˚C to +125˚C junction temperature range
@
mV 1 mA load.
@
Ground Pin Current: Typically 1 mA 200 mA load, and
@
200 µA 10 mA load.
Sleep Mode: The LP2986 draws less than 1 µA quiescent
current when shutdown pin is pulled low.
Error Flag: The built-in error flag goes low when the output
drops approximately 5% below nominal.
Applications
n Cellular Phone
Precision Output: The standard product versions available
can be pin-strapped (using the internal resistive divider) to
provide output voltages of 5.0V, 3.3V, or 3.0V with guaran-
teed accuracy of 0.5% (“A” grade) and 1% (standard grade)
at room temperature.
n Palmtop/Laptop Computer
n Camcorder, Personal Stereo, Camera
Block Diagram
01293501
™
VIP is a trademark of National Semiconductor Corporation.
© 2002 National Semiconductor Corporation
DS012935
www.national.com
Connection Diagrams and Ordering Information
Surface Mount Packages:
8-Lead LLP Surface Mount Package
01293502
SO-8/Mini SO-8 Package
See NS Package Drawing Number M08A/MUA08A
01293543
Top View
See NS Package Drawing Number LDC08A
Basic Application Circuits
Application Using Internal Resistive Divider
01293503
www.national.com
2
Basic Application Circuits (Continued)
Application Using External Divider
01293504
Ordering Information
TABLE 1. Package Marking and Ordering Information
Output Voltage
Mini SO-8
Grade
Order Information
LP2986AIMMX-5.0
LP2986AIMM-5.0
LP2986IMMX-5.0
LP2986IMM-5.0
Package Marking
Supplied as:
5
A
A
L41A
L41A
L41B
L41B
L40A
L40A
L40B
L40B
L39A
L39A
L39B
L39B
3500 Units on Tape and
Reel
5
1000 Units on Tape and
Reel
5
STD
STD
A
3500 Units on Tape and
Reel
5
1000 Units on Tape and
Reel
3.3
3.3
3.3
3.3
3.0
3.0
3.0
3.0
LP2986AIMMX-3.3
LP2986AIMM-3.3
LP2986IMMX-3.3
LP2986IMM-3.3
3500 Units on Tape and
Reel
A
1000 Units on Tape and
Reel
STD
STD
A
3500 Units on Tape and
Reel
1000 Units on Tape and
Reel
LP2986AIMMX-3.0
LP2986AIMM-3.0
LP2986IMMX-3.0
LP2986IMM-3.0
3500 Units on Tape and
Reel
A
1000 Units on Tape and
Reel
STD
STD
3500 Units on Tape and
Reel
1000 Units on Tape and
Reel
3
www.national.com
Ordering Information (Continued)
TABLE 1. Package Marking and Ordering Information (Continued)
Output Voltage
SO-8
Grade
A
Order Information
LP2986AIMX-5.0
LP2986AIM-5.0
LP2986IMX-5.0
LP2986IM-5.0
Package Marking
2986AIM5.0
2986AIM5.0
2986IM5.0
Supplied as:
5
2500 Units on Tape and
Reel
Shipped in Anti-Static
Rails
5
A
5
STD
STD
A
2500 Units on Tape and
Reel
5
2986IM5.0
Shipped in Anti-Static
Rails
3.3
3.3
3.3
3.3
3.0
3.0
3.0
3.0
LP2986AIMX-3.3
LP2986AIM-3.3
LP2986IMX-3.3
LP2986IM-3.3
2986AIM3.3
2986AIM3.3
2986IM3.3
2500 Units on Tape and
Reel
A
Shipped in Anti-Static
Rails
STD
STD
A
2500 Units on Tape and
Reel
2986IM3.3
Shipped in Anti-Static
Rails
LP2986AIMX-3.0
LP2986AIM-3.0
LP2986IMX-3.0
LP2986IM-3.0
2986AIM3.0
2986AIM3.0
2986IM3.0
2500 Units on Tape and
Reel
A
Shipped in Anti-Static
Rails
STD
STD
2500 Units on Tape and
Reel
2986IM3.0
Shipped in Anti-Static
Rails
8-Lead LLP
5
A
A
LP2986AILD-5
LP2986AILDX-5
LP2986ILD-5
L006A
L006A
1000 Units on Tape and
Reel
5
4500 Units on Tape and
Reel
5
STD
STD
A
L006AB
L006AB
L005A
1000 Units on Tape and
Reel
5
LP2986ILDX-5
LP2986AILD-3.3
LP2986AILDX-3.3
LP2986ILD-3.3
LP2986ILDX-3.3
LP2986AILD-3.0
LP2986AILDX-3.0
LP2986ILD-3.0
LP2986ILDX-3.0
4500 Units on Tape and
Reel
3.3
3.3
3.3
3.3
3.0
3.0
3.0
3.0
1000 Units on Tape and
Reel
A
L005A
4500 Units on Tape and
Reel
STD
STD
A
L005AB
L005AB
L004A
1000 Units on Tape and
Reel
4500 Units on Tape and
Reel
1000 Units on Tape and
Reel
A
L004A
4500 Units on Tape and
Reel
STD
STD
L004AB
L004AB
1000 Units on Tape and
Reel
4500 Units on Tape and
Reel
www.national.com
4
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Supply Voltage
(Operating)
2.1V to +16V
−0.3V to +16V
−0.3V to +5V
Shutdown Pin
Feedback Pin
Storage Temperature Range
Operating Junction
Temperature Range
Lead Temperature
−65˚C to +150˚C
Output Voltage
(Survival) (Note 4)
−0.3V to +16V
−40˚C to +125˚C
I
OUT (Survival)
Short Circuit Protected
Input-Output Voltage
(Survival) (Note 5)
(Soldering, 5 seconds)
ESD Rating (Note 2)
Power Dissipation (Note 3)
Input Supply Voltage
(Survival)
260˚C
2 kV
−0.3V to +16V
Internally Limited
−0.3V to +16V
Electrical Characteristics
Limits in standard typeface are for T = 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
J
less otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VS/D = 2V.
LM2986AI-X.X
LM2986I-X.X
(Note 6)
(Note 6)
Symbol
VO
Parameter
Output Voltage
Conditions
Typical
Units
Min
Max
Min
Max
5.0
5.0
3.3
3.3
3.0
3.0
4.975
4.960
4.910
3.283
3.274
3.241
2.985
2.976
2.946
5.025
5.040
5.090
3.317
3.326
3.359
3.015
3.024
3.054
0.014
4.950
4.920
4.860
3.267
3.247
3.208
2.970
2.952
2.916
5.050
5.080
5.140
3.333
3.353
3.392
3.030
3.048
3.084
0.014
(5.0V Versions)
<
<
0.1 mA IL 200 mA
Output Voltage
(3.3V Versions)
<
<
0.1 mA IL 200 mA
V
Output Voltage
(3.0V Versions)
<
<
0.1 mA IL 200 mA
Output Voltage Line
Regulation
VO(NOM) + 1V ≤ VIN ≤
0.007
%/V
mV
16V
0.032
0.032
VIN–VO
Dropout Voltage
(Note 7)
IL = 100 µA
IL = 75 mA
IL = 200 mA
IL = 100 µA
IL = 75 mA
IL = 200 mA
2.0
3.5
2.0
3.5
1
120
170
230
350
120
150
800
1400
2.1
120
170
230
350
120
150
800
1400
2.1
90
180
100
500
1
IGND
Ground Pin Current
µA
mA
µA
3.7
3.7
<
VS/D 0.3V
0.05
400
1.5
1.5
IO(PK)
Peak Output Current
Short Circuit Current
VOUT ≥ VO(NOM) − 5%
RL = 0 (Steady State)
(Note 11)
250
250
mA
IO(MAX)
400
160
en
Output Noise Voltage
(RMS)
BW = 300 Hz to 50 kHz,
COUT = 10 µF
µV(RMS)
dB
Ripple Rejection
f = 1 kHz, COUT = 10 µF
65
5
www.national.com
Electrical Characteristics (Continued)
Limits in standard typeface are for T = 25˚C, and limits in boldface type apply over the full operating temperature range. Un-
J
less otherwise specified: VIN = VO(NOM) + 1V, IL = 1 mA, COUT = 4.7 µF, CIN = 2.2 µF, VS/D = 2V.
LM2986AI-X.X
LM2986I-X.X
(Note 6)
(Note 6)
Symbol
Parameter
Conditions
(Note 9)
Typical
Units
Min
Max
Min
Max
Output Voltage
Temperature Coefficient
20
ppm/˚C
FEEDBACK PIN
VFB Feedback Pin Voltage
1.21
1.20
1.19
1.25
1.26
1.28
1.20
1.19
1.18
1.26
1.27
1.29
1.23
1.23
V
(Note 10)
(Note 9)
FB Pin Voltage
20
150
0.1
ppm/˚C
nA
Temperature Coefficient
IFB
Feedback Pin Bias
Current
IL = 200 mA
(Note 9)
330
330
760
760
FB Pin Bias Current
nA/˚C
Temperature Coefficient
SHUTDOWN INPUT
VS/D S/D Input Voltage
VH = O/P ON
VL = O/P OFF
VS/D = 0
1.4
0.55
0
1.6
1.6
V
(Note 8)
0.18
−1
0.18
−1
IS/D
S/D Input Current
µA
VS/D = 5V
5
15
15
ERROR COMPARATOR
IOH
Output “HIGH” Leakage
VOH = 16V
1
1
0.01
150
µA
2
2
VOL
Output “LOW” Voltage
Upper Threshold Voltage
Lower Threshold Voltage
Hysteresis
VIN = VO(NOM) − 0.5V,
IO(COMP) = 300 µA
220
350
−3.5
−2.5
−4.9
−3.3
220
350
−3.5
−2.5
−4.9
−3.3
mV
VTHR
−5.5
−7.7
−5.5
−7.7
−4.6
(MAX)
VTHR
(MIN)
−8.9
−8.9
%VOUT
−6.6
2.0
−13.0
−13.0
HYST
www.national.com
6
Electrical Characteristics (Continued)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the
device outside of its rated operating conditions.
Note 2: The ESD rating of the Feedback pin is 500V and the Tap pin is 1.5 kV.
Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, T (MAX), the junction-to-ambient thermal resistance, θ
,
J−A
J
and the ambient temperature, T . The maximum allowable power dissipation at any ambient temperature is calculated using:
A
The value of θ
for the SO-8 (M) package is 160˚C/W, and the mini SO-8 (MM) package is 200˚C/W. The value θ
for the LLP (LD) package is specifically
J−A
J−A
dependent on PCB trace area, trace material, and the number of layers and thermal vias. For improved thermal resistance and power dissipation for the LLP
package, refer to Application Note AN-1187. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into
thermal shutdown.
Note 4: If used in a dual-supply system where the regulator load is returned to a negative supply, the LM2986 output must be diode-clamped to ground.
Note 5: The output PNP structure contains a diode between the V and V
terminals that is normally reverse-biased. Forcing the output above the input will
OUT
IN
turn on this diode and may induce a latch-up mode which can damage the part (see Application Hints).
Note 6: Limits are 100% production tested at 25˚C. Limits over the operating temperature range are guaranteed through correlation using Statistical Quality Control
(SQC) methods. The limits are used to calculate National’s Average Outgoing Quality Level (AOQL).
Note 7: Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1V differential.
Note 8: To prevent mis-operation, the Shutdown input must be driven by a signal that swings above V and below V with a slew rate not less than 40 mV/µs (see
H
L
Application Hints).
Note 9: Temperature coefficient is defined as the maximum (worst-case) change divided by the total temperature range.
Note 10: V ≤ V ≤ (V − 1), 2.5V ≤ V ≤ 16V, 100 µA ≤ I ≤ 200 mA, T ≤ 125˚C.
FB
OUT
IN
IN
L
J
Note 11: See Typical Performance Characteristics curves.
7
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA.
VOUT vs Temperature
Dropout Voltage vs Temperature
01293508
01293509
Dropout Voltage vs Load Current
Dropout Characteristics
01293510
01293513
Ground Pin Current vs Temperature and Load
Ground Pin Current vs Load Current
01293512
01293511
www.national.com
8
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued)
Input Current vs VIN
Input Current vs VIN
01293515
01293514
Load Transient Response
Load Transient Response
01293516
01293517
Line Transient Response
Line Transient Response
01293518
01293520
9
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued)
Turn-On Waveform
Turn-Off Waveform
01293523
01293521
Short Circuit Current
Short Circuit Current
01293524
01293525
Short Circuit Current vs Output Voltage
Instantaneous Short Circuit Current vs Temperature
01293527
01293526
www.national.com
10
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued)
DC Load Regulation
Feedback Bias Current vs Load
01293529
01293528
Feedback Bias Current vs Temperature
Shutdown Pin Current vs Shutdown Pin Voltage
01293531
01293530
Shutdown Voltage vs Temperature
Input to Output Leakage vs Temperature
01293532
01293537
11
www.national.com
Typical Performance Characteristics Unless otherwise specified: TA = 25˚C, COUT = 4.7 µF,
CIN = 2.2 µF, S/D is tied to VIN, VIN = VO(NOM) + 1V, IL = 1 mA. (Continued)
Output Noise Density
Output Impedance vs Frequency
01293535
01293534
Output Impedance vs Frequency
Ripple Rejection
01293536
01293533
Application Hints
LLP Package Devices
Curves are provided which show the allowable ESR range
as a function of load current for various output voltages and
capacitor values (see ESR curves below).
The LP2986 is offered in the 8 lead LLP surface mount
package to allow for increased power dissipation compared
to the SO-8 and Mini SO-8. For details on thermal perfor-
mance as well as mounting and soldering specifications,
refer to Application Note AN-1187.
ESR Curves For 5V Output
EXTERNAL CAPACITORS
Like any low-dropout regulator, external capacitors are re-
quired to assure stability. These capacitors must be correctly
selected for proper performance.
INPUT CAPACITOR: An input capacitor (≥ 2.2 µF) is re-
quired between the LP2986 input and ground (amount of
capacitance may be increased without limit).
This capacitor must be located a distance of not more than
0.5” from the input pin and returned to a clean analog
ground. Any good quality ceramic or tantalum may be used
for this capacitor.
OUTPUT CAPACITOR: The output capacitor must meet the
requirement for minimum amount of capacitance and also
have an appropriate E.S.R. (equivalent series resistance)
value.
01293506
www.national.com
12
ALUMINUM: The large physical size of aluminum electrolyt-
ics makes them unattractive for use with the LP2986. Their
ESR characteristics are also not well suited to the require-
ments of LDO regulators.
Application Hints (Continued)
ESR Curves For 2.5V Output
The ESR of an aluminum electrolytic is higher than a tanta-
lum, and it also varies greatly with temperature.
A typical aluminum electrolytic can exhibit an ESR increase
of 50X when going from 20˚C to −40˚C. Also, some alumi-
num electrolytics can not be used below −25˚C because the
electrolyte will freeze.
USING AN EXTERNAL RESISTIVE DIVIDER
The LP2986 output voltage can be programmed using an
external resistive divider (see Basic Application Circuits).
The resistor connected between the Feedback pin and
ground should be 51.1k. The value for the other resistor (R1)
connected between the Feedback pin and the regulated
output is found using the formula:
01293507
VOUT = 1.23 x (1 + R1/51.1k)
It should be noted that the 25 µA of current flowing through
the external divider is approximately equal to the current
saved by not connecting the internal divider, which means
the quiescent current is not increased by using external
resistors.
IMPORTANT: The output capacitor must maintain its ESR in
the stable region over the full operating temperature range of
the application to assure stability.
The minimum required amount of output capacitance is
4.7 µF. Output capacitor size can be increased without limit.
A lead compensation capacitor (CF) must also be used to
place a zero in the loop response at about 50 kHz. The value
It is important to remember that capacitor tolerance and
variation with temperature must be taken into consideration
when selecting an output capacitor so that the minimum
required amount of output capacitance is provided over the
full operating temperature range. A good Tantalum capacitor
will show very little variation with temperature, but a ceramic
may not be as good (see next section).
for C can be found using:
F
CF = 1/(2π x R1 x 50k)
A good quality capacitor must be used for CF to ensure that
the value is accurate and does not change significantly over
temperature. Mica or ceramic capacitors can be used, as-
±
suming a tolerance of 20% or better is selected.
CAPACITOR CHARACTERISTICS
If a ceramic is used, select one with a temperature coeffi-
cient of NPO, COG, Y5P, or X7R. Capacitor types Z5U, Y5V,
and Z4V can not be used because their value varies more
that 50% over the −25˚C to +85˚C temperature range.
TANTALUM: The best choice for size, cost, and perfor-
mance are solid tantalum capacitors. Available from many
sources, their typical ESR is very close to the ideal value
required on the output of many LDO regulators.
SHUTDOWN INPUT OPERATION
Tantalums also have good temperature stability: a 4.7 µF
was tested and showed only a 10% decline in capacitance
as the temperature was decreased from +125˚C to −40˚C.
The ESR increased only about 2:1 over the same range of
temperature.
The LP2986 is shut off by driving the Shutdown input low,
and turned on by pulling it high. If this feature is not to be
used, the Shutdown input should be tied to VIN to keep the
regulator output on at all times.
However, it should be noted that the increasing ESR at lower
temperatures present in all tantalums can cause oscillations
when marginal quality capacitors are used (where the ESR
of the capacitor is near the upper limit of the stability range at
room temperature).
To assure proper operation, the signal source used to drive
the Shutdown input must be able to swing above and below
the specified turn-on/turn-off voltage thresholds listed as VH
and VL, respectively (see Electrical Characteristics).
It is also important that the turn-on (and turn-off) voltage
signals applied to the Shutdown input have a slew rate which
is not less than 40 mV/µs.
CERAMIC: For a given amount of a capacitance, ceramics
are usually larger and more costly than tantalums.
Be warned that the ESR of a ceramic capacitor can be low
enough to cause instability: a 2.2 µF ceramic was measured
and found to have an ESR of about 15 mΩ.
CAUTION: the regulator output state can not be guaranteed
if a slow-moving AC (or DC) signal is applied that is in the
range between VH and VL.
If a ceramic capacitor is to be used on the LP2986 output, a
1Ω resistor should be placed in series with the capacitor to
provide a minimum ESR for the regulator.
REVERSE INPUT-OUTPUT VOLTAGE
The PNP power transistor used as the pass element in the
LP2986 has an inherent diode connected between the regu-
lator output and input.
Another disadvantage of ceramic capacitors is that their
capacitance varies a lot with temperature:
During normal operation (where the input voltage is higher
than the output) this diode is reverse-biased.
Large ceramic capacitors are typically manufactured with the
Z5U temperature characteristic, which results in the capaci-
tance dropping by a 50% as the temperature goes from 25˚C
to 80˚C.
However, if the output is pulled above the input, this diode
will turn ON and current will flow into the regulator output.
This means you have to buy a capacitor with twice the
minimum COUT to assure stable operation up to 80˚C.
13
www.national.com
VIN to VOUT (cathode on VIN, anode on VOUT), to limit the
reverse voltage across the LP2986 to 0.3V (see Absolute
Maximum Ratings).
Application Hints (Continued)
In such cases, a parasitic SCR can latch which will allow a
high current to flow into VIN (and out the ground pin), which
can damage the part.
In any application where the output may be pulled above the
input, an external Schottky diode must be connected from
www.national.com
14
Physical Dimensions inches (millimeters)
unless otherwise noted
8-Lead Mini-Small Outline Molded Package, JEDEC
NS Package Number MUA08A
15
www.national.com
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8-Lead (0.150” Wide) Molded Small Outline Package, JEDEC
NS Package Number M08A
www.national.com
16
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8-Lead LLP Surface Mount Package
NS Package Number LDC08A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: support@nsc.com
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
相关型号:
LP2986ILDX-3.0/NOPB
FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.35V DROPOUT, PDSO8, ROHS COMPLIANT, LLP-8
TI
LP2986ILDX-3.3/NOPB
Micropower, 200 mA Ultra Low-Dropout Fixed or Adjustable Voltage Regulator 8-WSON -40 to 125
TI
LP2986ILDX-5
IC VREG FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.35 V DROPOUT, PDSO8, LLP-8, Fixed/Adjustable Positive Single Output LDO Regulator
NSC
LP2986IM-3.0/NOPB
200-mA, 16-V, low-dropout voltage regulator with adjustable or fixed voltage configuration 8-SOIC -40 to 125
TI
LP2986IM-3.3/NOPB
IC VREG FIXED/ADJUSTABLE POSITIVE LDO REGULATOR, 0.35 V DROPOUT, PDSO8, ROHS COMPLIANT, 0.150 INCH, PLASTIC, SO-8, Fixed/Adjustable Positive Single Output LDO Regulator
NSC
©2020 ICPDF网 联系我们和版权申明