LQ295T3LZ31_技术文档

TECHNICAL LITERATURE

Liquid Crystal Display Group

®

LQ295T3LZ31

TFT LCD Module

(Model No.: LQ295T3LZ31)

Issue Date: June 24, 2002

No.

LD – 14350B

JUN．24．2002

DATE

TECHNICAL

LITERATURE

FOR

TFT - LCD module

LQ295T3LZ31

MODEL No.

The technical literature is subject to change without notice.

So, please contact SHARP or its representative before designing

your product based on this literature.

DEVELOPMENT ENGINEERING DEPARTMENT 2

AVC LIQUID CRYSTAL DISPLAY DIVISION

ꢀ

AVC LIQUID CRYSTAL DISPLAY GROUP

ꢀ

SHARP CORPORATION

sharp

RECORDS OF REVISION

LQ295T3LZ31

SPEC No.

DATE

SUMMARY

NOTE

REVISED

No.

PAGE

LD-14350

Mar. 04. 2002

-

1

-

1 st Issue

LD-14350A Apr. 12. 2002 ▲1

I/F signal 24bit -> LVDS

Pixel configuration R,G,B -> B,G,R

▲2

▲3

▲4

10 Pixel configuration R,G,B -> B,G,R

2

1

2

5

Change the I/F Connector

LD-14350B

JUN.24.2002

▲1

▲2

▲3

▲4

▲5

Addition of O/S driving

Correction of Unit outline dimensions

Change of LVDS receiver

Correction of Pull up/down value

Addition of I/F connector CN2

(for O/S driving)

▲6

▲7

6

8

Correction of I/Fconector CN1->CN3

(for Inverter control)

Correction of I/Fconector CN2->CN1,CN2

(for Inverter power)

▲8

▲9

Correction of data table

12 Correction of data table

13 Change of Handling precaution of the

Module

▲10

▲11

15 Change of Others

sharp

LD-14350B 1/16

1. Application

This technical literature applies to the color 29.5” Wide XGA TFT-LCD module LQ295T3LZ31.

* These specification sheets are proprietary products of SHARP CORPORATION (“SHARP”) and include materials

protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by

any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of

SHARP.

* The device listed in these technical literature sheets was designed and manufactured for use in AV equipment.

* In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains,

automobiles, etc.), rescue and security equipment and various safety related equipment which require higher

reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant

system design should be taken.

* Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,

telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for

life support.

* SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with

the instructions and the precautions specified in these technical literature sheets.

* Contact and consult with a SHARP sales representative for any questions about this device.

2. Overview

This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is

composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, inverter circuit and back light

system etc. Graphics and texts can be displayed on a 1280×RGB×768 dots panel with 16,777,216 colors by

using LVDS (Low Voltage Differential Signaling) to interface, +5V of DC supply voltages and supply voltage for

back light.

This module also includes the DC/AC inverter to drive the CCFT .

And in order to improve the response time of LCD, this module have decided to apply the O/S (over shoot)driving

technology for the control circuit.In the O/S driving technology,signals are being applied to the Liquid Crystal

according to a pre-fixed process as an image signal of the present frame in case a difference is found between image

signal of the previous frame and that of the current frame after comparing them.

▲１

By using the captioned process,the image signals of this LCD module are being set so that image response can be

completed within one frame,as a result,image blur can be improved and clear image performance can be realized.

3. Mechanical Specifications

Parameter

Display size

Specifications

75 （Diagonal）

Unit

cm

inch

mm

pixel

29.5 （Diagonal）

643.20 (H) x 384.77 (V)

1280 (H) x 768 (V)

Active area

Pixel Format

（1pixel = R + G + B dot）

0.5025(H) x 0.501 (V)

B, G, R vertical stripe

Normally black

Pixel pitch

Pixel configuration

Display mode

Unit Outline Dimensions *1

Mass

Surface treatment

mm

▲2

(707)(W) x (422.5)(H) x (51.3)(D)

(10800)

Anti glare, low reflection coating

Hard coating: 2H

mm

ｇ

Haze: 23 +/- 5%

(*1)Outline dimensions are shown in Fig.1

sharp

LD-14350B 2/16

4. Input Terminals

4-1. TFT panel driving

(Shown in Fig.1)

CN1 (Interface signals and +5VDC power supply)

Using connector ：FI-X30S-HF (Japan Aviation Electronics Ind., Ltd.)

Mating connector ：FI-X30H,FI-X30C or FI-X30M (Japan Aviation Electronics Ind., Ltd.)

Using LVDS receiver ：THC63LVDF84B (Thine) ▲3

Mating LVDS transmitter：THC63LVDM83A or interchangeable device

Pin No.

Symbol

VCC

GND

Function

Remark

1

2

3

4

5

6

7

8

+5VꢀPower Supply

GND

▲4

SELLVDS

9

Select LVDS data order 【Note1】

3.3V 10kΩ Pull Up

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

NC

GND

RIN0-

RIN0+

GND

RIN1-

RIN1+

GND

RIN2-

RIN2+

GND

CLKIN-

CLKIN+

GND

RIN3-

RIN3+

GND

Ground

Negative (-) LVDS differential data input

Positive (+) LVDS differential clock input

Ground

Negative (-) LVDS differential data input

Positive (+) LVDS differential clock input

Ground

Negative (-) LVDS differential data input

Positive (+) LVDS differential clock input

Ground

LVDS

Clock Signal(-)

ꢀ

LVDS

Clock Signal(+)

ꢀ

Ground

Negative (-) LVDS differential data input

Positive (+) LVDS differential clock input

Ground

LVDS

R▲/L4

Horizontal shift direction【Note 3】

Vertical shift direction【Note 3】

3.3V 10kΩ Pull down

ꢀ

▲4

U/D

ꢀ

Reserved

* Shield case contacts GND(Ground) of LCD module.

sharp

LD-14350B 3/16

Note1 SELLVDS

【

】

Transmitter

Pin No

SELLVDS

=H(3.3V) or Open

=L(GND)

R0(LSB)

R1

Data

TA0

TA1

TA2

TA3

TA4

TA5

TA6

TB0

TB1

TB2

TB3

TB4

TB5

TB6

TC0

TC1

TC2

TC3

TC4

TC5

TC6

TD0

TD1

TD2

TD3

TD4

TD5

TD6

51

52

54

55

56

3

4

6

7

11

12

14

15

19

20

22

23

24

27

28

30

50

2

R2

R3

R4

R5

R6

R2

R3

R4

R5

R7(MSB)

G2

G0(LSB)

G1

G3

G4

G5

G6

G2

G3

G4

G5

G7(MSB)

B2

B0(LSB)

B1

B3

B4

B5

B6

B2

B3

B4

B5

B7(MSB)

NC

(RSV1)

DE

R0(LSB)

R1

G0(LSB)

G1

NC

(RSV1)

DE

R6

R7(MSB)

G6

G7(MSB)

B6

B7(MSB)

(NA)

8

10

16

18

25

B0(LSB)

B1

(NA)

sharp

LD-14350B 4/16

SELLVDS= Low(GND)

1 cycle

CKAIN+

CKAIN-

RIN0+

RIN0-

R1

G2

B3

R7

R0

G1

B2

R6

G0

R5

B0

NA

B7

R4

G5

NA

B6

R3

G4

B5

G7

R2

G3

B4

G6

R1

G2

B3

R7

R0

G1

B2

R6

G0

B1

RIN1+

RIN1-

RIN2+

RIN2-

DE

NA

DE

NA

RIN3+

RIN3

SELLVDS= High(3.3V) or Open

1 cycle

CKIN+

CKIN-

RIN0+

RIN0-

R3

G4

B5

R1

R2

G3

B4

R0

G2

R7

B2

NA

B1

R6

G7

NA

B0

R5

G6

B7

G1

R4

G5

B6

G0

R3

G4

B5

R1

R2

G3

B4

R0

G2

RIN1+

RIN1-

B3

RIN2+

RIN2-

DE

NA

DE

NA

RIN3+

RIN3-

DE: Display Enable

NA: Not Available (Fixed Low)

sharp

LD-14350B 5/16

【Note 2】The horizontal display start timing is settled in accordance with a rising timing of DE signal.

Don’t keep DE “ High “ during operation.

【Note 3】

Source Connector

R/L : L

ꢀꢀꢀꢀ

R/L : H

U/D : L

Gate connector

Source connector

Gate connector

ꢀꢀꢀꢀU/D : Lꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

Source connector

R/L : Lꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

ꢀꢀꢀ U/D : Hꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ U/D : H

R/L : H

Gate connector

CN2(O/S control)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ▲５

Using connector: SM07B-SRSS-TB-A (JST)

Pin No.

Function

Remark

1

2

3

4

5

6

7

Change of flame frequencyꢀꢀꢀ

Change of O/S operation

Reserved

0:50Hz, 1:60Hz

0:off, 1:on

Pull down

Reserved

Data2 of panel surface temperature

Data1 of panel surface temperature

Gnd

【Note 1】CN2

Pin no.

Without

With O/S driving

O/S driving

Frame frequency 50Hz

Panel surface temperature degree C

Frame frequency 60Hz

Panel surface temperature degree C

0-15

15-25

25-40

Over 40

0-15

15-25

25-40

Over 40

1

2

3

4

5

6

7

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

Gnd

0

Gnd

1

Gnd

0

Gnd

1

Gnd

0

Gnd

1

Gnd

0

Gnd

1

Gnd

sharp

LD-14350B 6/16

Detect temperature on PWB in users side. Check correlation between temperature on PWB and panel surface,

and input temperature data.

Value of upper or lower temperature area is setting result of clear image performance.

4-2. Backlight driving

CN3 (Inverter control)

Using connector: S3B-PH-SM3-TB(JST)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ▲６

Pin No.

Symbol

Function

Remark

1

2

3

VON

ON/OFF

Brightness Control

GND

【Note 1】

【Note 2】

VBRT

GND

【Note 1】 ON/OFF Function

Input voltage

Function

5V

0V

Inverter: ON

Inverter: OFF

【Note 2】 Brightness control function

Brightness control is available for 0 – 5 V analog input voltage.

Input voltage

Function

5V

0V

Brightness Control (15%) : (Dark)

Brightness Control (100%) : (Bright)

CN1,CN2 (Inverter Power) Using connector: S6B-PH-SM3-TB (JST)ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ▲７

Pin No.

Function

1

2

3

4

5

6

12V

GND

4-3. Lamp characteristics

The back light system is under-lighting type with 12 CCFTs(Cold Cathode Fluorescent Tube).

The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of

one CCFT.

ꢀItem

Life time

Symbol

Min.

TBD

Typ.

-

Max.

-

Unit

hour

Remarks

【Note 1】

TL

【Note 1】Lamp life time is defined as the time when the situation 1 occurs in the continuous

operation under the condition of Ta=25 degree and brightness control(100%).

1. Brightness becomes 50% of the original value under standard condition.

5. Absolute Maximum Ratings

Parameter

Input voltage

(for Control)

Symbol

Condition

Ta=25 degree

Ratings

-0.3 ~ 3.6

Unit

V

Remark

【Note 1】

VI

5V supply voltage

(for Control)

Input voltage

(for Inverter)

12V supply voltage

(for Inverter)

VCC

Ta=25 degree

0 ~ + 6

0 ~ +14

V

VBRT

VON

V_INV

V

Storage temperature

Operation temperature

(Ambient)

Tstg

Topa

-

-25 ~ +60

0 ~ +50

Degree

Degree 【Note 2】

【Note 1】SELLVDS, R/L, U/D

【Note 2】Humidity 95%RH Max.(Ta≦40 degree)

Maximum wet-bulb temperature at 39 degree or less.(Ta>40 degree)

No condensation.

sharp

LD-14350B 7/16

Ta=25 degree

6. Electrical Characteristics

6-1. Control circuit driving

Parameter

Symbol Min.

Typ.

+5.0

TBD

Max.

+5.5

TBD

Uniit

V

mA

Remark

【Note 1】

【Note 2】

Supply voltage Vcc

Current Icc

dissipation

Permissive input ripple voltage VRP

+4.5

-

+5V supply

voltage

-

100

(100)

-

(1.0)

-

mVP-P

mV

V

Vcc = +5.0V

V^CM= +1.2V

【Note 8】

Differential input

threshold voltage

High

Low

VTH

V^TL

VIL

VIH

-

(-100)

-

Input Low voltage

Input High voltage

【Note 3】

(2.3)

V

V^I= 0V

【Note 4】

V^I= 0V

【Note 5】

V^I=Vcc

IIL1

IIL2

IIH1

-

TBD

µA

Input leak current (Low)

【Note 6】

V^I=Vcc

Input leak current (High)

Terminal resistor

I^IH2

-

TBD

-

µA

【Note 7】

Differential input

RT

100

Ω

【Note】VCM: Common mode voltage of LVDS driver.

【Note 1】

1) Input voltage sequences

Vcc

4.5V

2.7V

data

0 < t1 ≦ 10ms, 0 < t2 ≦ 10ms

0 < t3 ≦ 1s, t4 ≧ 1s

t3

t4

t1

t2

2) Dip conditions for supply voltage

a) 2.7V ≦ Vcc < 4.5V

td ≦ 10ms

Vcc

．

b) Vcc < 2.7V

．

td

Condition of Dip conditions for supply voltage is

based on input voltage sequence.

【Note 2】Typical current situation: 16 gray-bar pattern (Vcc = +5.0V)

The explanation of RGB gray scale is seen in section 8.

RGB

RGB RGB

....

GS0 GS16 GS32

GS224 GS240

【Note 3】R/L, U/D, SELLVDS

【Note 4】R/L, U/D

【Note 5】SELLVDS

【Note 6】R/L, U/D

【Note 7】SELLVDS

【Note 8】CKIN, RIN1, RIN2, RIN3

sharp

LD-14350B 8/16

6-2. Inverter driving for back light ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ ▲８

The back light system is under-lighting type with 12 CCFTs (Cold Cathode Fluorescent Tube).

Ta=25℃

Parameter

Symbol

Min.

Typ.

Max.

Unit

Remark

Current dissipation

IINV

TBD

(6.5)

TBD

A

VBRT = 0V

＋12V

Supply voltage

Permissive input ripple

voltage

VINV

VRF

11

-

12

-

13

100

V

mVp-p

【Note 1】

VINV = +12V

Input voltage (Low)

Input voltage (High)

Brightness control

voltage(100%)

VONL

VONH

VBRT

-

3

0

-

0.5

5.0

0.3

V

【Note 2】

impedance=24.7kΩ

【Note 3】【Note 4】

impedance=20.6kΩ

Brightness control voltage

VBRT

0.7

5.0

V

【Note 1】1)VINV-turn-on condition

12V

11V

0V

Ｖ_INV

0～5V

T5

T7

0V

Ｖ_BRT

5V

T6

0V

Ｖ_ON

※ T5＞100μs

※ T6＞1ms

※ T7＞1ms

2) V^INV-turn-off condition

12V

Ｖ_INV

T8

0V

0～5V

Ｖ_BRT

T9

5V

Ｖ_ON

0V

※ T8＞1ms

※ T9＞1ms

【Note 2】VON

【Note 3】VBRT

【Note 4】Refrain from using the device under the condition of V_BRT=0.5±0.2Ｖbecause of the possibility of flicker

on display. In case of V_BRT>5.0V,the protective circuit may stop driving the inverter.

sharp

LD-14350B 9/16

7. Timing characteristics of input signals

7-1. Timing characteristics

Timing diagrams of input signal are shown in Fig.3.

Parameter

Frequency

Symbol

1/Tc

TH

Min.

TBD

1280

TBD

768

Typ.

82

1696

20.67

1280

806

Max.

85

TBD

-

1280

TBD

768

Unit

MHz

clock

µs

clock

line

Remark

Clock

Horizontal period

Data enable

signal

Horizontal period (High)

Vertical period

Vertical period (High)

THd

TV

TVd

【Note1】

768

line

【Note1】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.

【Note2】 In case of turn-off, turn-off may be after input signal for “black”.

TH

THd

DE

1

2

DATA

1280

Tc

1280

(R,G,B)

1

2

767 768

DE

TVd

TV

sharp

LD-14350B 10/16

7-2. Input data signal and display position on the screen

B1 G1 R1 B2 G2 R2

(１､１) (１,２)

１・１１・２１・３

２・１２・２

３・１

1･1280

B G R

768･1280

768･1

Display Position of Data (V,H)

sharp

LD-14350B 11/16

8. Input Signal, Basic Display Colors and Gray Scale of Each Color

Data signal

Colors &

Gray R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7

Scale

Gray scale

Black

Blue

－

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

Green

Cyan

Red

Magenta

Yellow

White

Black

×

GS0

GS1

GS2

È

0

1

0

1

0

Darker

×

È

Ø

È

Brighter GS253

1

0

1

0

1

0

Ø

GS254

GS255

Red

Black

×

GS0

GS1

GS2

È

0

1

0

1

0

Darker

×

È

Ø

È

Brighter GS253

GS254

Green GS255

0

1

0

1

0

1

0

Ø

Black

×

GS0

GS1

GS2

È

0

1

0

1

0

Darker

×

È

Ø

È

Brighter GS253

0

1

0

1

0

1

Ø

GS254

GS255

Blue

0 : Low level voltage,

1 : High level voltage.

Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of total

24 bit data signals, the 16-million-color display can be achieved on the screen.

sharp

LD-14350B 12/16

9. Optical characteristicsꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ▲９

Ta=25 degree, Vcc = +5V, V^INV= +12V

Parameter

Symbol

θ21,

θ22

θ11

θ12

CRn

Condition

Min.

TBD

Typ.

85

Max.

-

Unit

Deg.

Remark

Horizontal

Vertical

Viewing angle

CR≧10

【Note1,4】

VBRT=0V

range

TBD

-

85

-

Deg.

500

【Note2,4】

VBRT=0V

Contrast ratio

-

(10)

(15)

(0.308)

TBD

-

ms

-

Rise

Decay

τr

τd

X

【Note3,4】

VBRT=0V

Response time

θ=0 deg.

【Note 4】

VBRT=0V

【Note 4】

【Note 5】

Chromaticity of white

Y

Y^L1

-

(0.306)

(450)

-

Cd/m2

Luminance of white

-

(1.25)

Luminance uniformity

δ

Ｗ

*The measurement shall be executed 30 minutes after lighting at rating.

【Note 1】Definitions of viewing angle range :

Normal line

θ11

θ22

θ12

θ21

6 o’clock direction

【Note 2】Definition of contrast ratio :

The contrast ratio is defined as the following.

Luminance(brightness) with all pixels white

Luminance(brightness) with all pixels black

Contrast Ratio (CR) =

【Note 3】Definition of response time

The response time is defined as the following figure and shall be measured by switching the input signal for

“black” and “white”.

White

black

white

100%

90%

10%

0%

τ

r

τ

d

time

sharp

LD-14350B 13/16

【Note 4】This shall be measured at center of the screen.

【Note 5】Definition of white uniformity ;

White uniformity is defined as the following with five measurements.(A～E)

maximum Luminance of five points(brightness)

minimum Luminance of five points(brightness)

pixel

320 640 960

^Ｗ＝

δ

A

B

D

E

192

384

C

576

pixel

10. Display Quality

The display quality of the color TFT-LCD module shall be

compliance with the incoming inspection standard.

▲１０

11. Handling Precautions of the module

a) Be sure to turn off the power supply when inserting or disconnecting the cable.

b) Brightness control voltage is switched for “ON” and “OFF”, as shown in Fig.4. Voltage difference generated

by this switching, ΔVINV, may affect a sound output, etc. when the power supply is shared between the

inverter and its surrounding circuit. So, separate the power supply of the inverter circuit with the one of its

surrounding circuit.

V

㰱

INV

V_INV

0V

0A

I

INV

ON

OFF

ON

Duty

0V

Fig.4 Brightness control voltage.

c) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or

twist.

d) Since the front polarizer is easily damaged, pay attention not to scratch it.

e) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.

f) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

g) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with

care.

h) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into

consideration when handling.

i) The module has some printed circuit boards (PCBs) on the back side, take care to keep them form any stress

or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs may be

damaged.

j) Observe all other precautionary requirements in handling components.

k) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity

sharp

LD-14350B 14/16

issue, functional defect, etc.. So, please avoid such design.

l) When giving a touch to the panel at power on supply, it may cause some kinds of degradation. In that case,

once turn off the power supply, and turn on after several seconds again, and that is disappear.

m) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in

the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent,

adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD

modules.

12. Packing form

a) Piling number of cartons: maximum TBD

b) Packing quantity in one carton: TBD

c) Carton size: TBD

d) Total mass of one carton filled with full modules: TBD

sharp

LD-14350B 15/16

13. Reliability test items

No.

1

2

Test item

High temperature storage test

Low temperature storage test

Conditions

Ta= 60℃

Ta= - 25℃ 240h

240h

3

High temperature and high humidity

operation test

℃

Ta= 40 ; 95%RH 240h

(No condensation)

4

5

6

High temperature operation test

Low temperature operation test

Ta= 50℃ 240h

Ta= 0℃

240h

Frequency : 10 ~ 57Hz/Vibration width(one side) : 0.075mm

: 58 ~ 500Hz/Acceleration: 9.8m/s2

Vibration test

(non-operation)

Sweep time: 11 minutes

Test period : 3 hours(1h for each direction of X, Y, Z)

7

Max. acceleration: 490m/s2

Pulse width : 11ms, sinusoidal half wave

Direction : +/-X, +/-Y, +/-Z, once for each direction.

Shock test

(non-operation)

【Note】Ta = Ambient temperature

【Result evaluation criteria】

Under the display quality test conditions with normal operation state, these shall be no change which may affect

practical display function.

▲１１

14. Others

1) Lot No. and indication Bar Code Label: (TBD)

SHARP

Model No.

LQ295T3LZ31

Bar Code(Lot No.)

Lot No.

2Y XXXXXXX

MADE IN JAPAN

How to express Lot No.

A production year (the last figures of the Christian Era)

Serial No.

A production month (1～9,X,Y,Z)

2) Packing Label

① Model No. (LQ295T3LZ31)

^{␠ౝຠ⇟㧦}（４Ｓ）LQ295T3LZ31

② Lot No. (Date)

ꢀ③ Quantity

Bar code（①）

^{㧸㨛㨠㧺㧻㧚ꢀ ꢀ 㧦}（１Ｔ）２００２．１１．1５

Bar code（②）

^{㧽㨡㨍㨚㨠㨕㨠㨥㧦}（Ｑ）１

Bar code（③）

ｐｃｓ

࡙

࡯

ࠩຠ⇟ꢀ ꢀ ꢀ 㧦

シャープ物流用ラベルです。

3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.

If adjusted value is changed, the specification may not be satisfied.

4) Disassembling the module can cause permanent damage and should be strictly avoided.

sharp

LD-14350B 16/16

5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.

6) The chemical compound, which causes the destruction of ozone layer, is not used.

ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ

7) Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury. Please follow local

ordinances or regulations for disposal. (put on the back of the module. )

COLD CATHODE FLUORESCENT LAMP IN LCD PANEL

CONTAINS

FOLLOW

A SMALL AMOUNT OF MERCURY, PLEASE

LOCAL ORDINANCES OR REGULATION FOR DISPOSAL

当該液晶

ディスプレイパネルは蛍光管が組み込まれていますので、地方自冶

体の条例、または、規則に従って廃棄ください。

8) When any question or issue occurs, it shall be solved by mutual discussion.

◎ Carton storage condition

Temperature

0℃ to 40℃

Humidity

95%RH or less

Reference condition : 20℃ to 35℃ , 85%RH or less (summer)

5℃ to 15℃ , 85%RH or less (winter)

:

・the total storage time (40℃,95%RH) : 240H or less

Be sure to shelter a product from the direct sunlight.

Harmful gas, such as acid and alkali which bites electronic components and/or

wires must not be detected.

Sunlight

Atmosphere

Notes

Be sure to put cartons on palette or base, don’t put it on floor, and store them with

removing from wall

Please take care of ventilation in storehouse and around cartons, and control

changing temperature is within limits of natural environment

1 year

Storage period

sharp

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited

Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND

FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,

for any incidental or consequential economic or property damage.

NORTH AMERICA

EUROPE

JAPAN

SHARP Corporation

SHARP Microelectronics of the Americas

5700 NW Pacific Rim Blvd.

Camas, WA 98607, U.S.A.

Phone: (1) 360-834-2500

Fax: (1) 360-834-8903

SHARP Microelectronics Europe

Division of Sharp Electronics (Europe) GmbH

Sonninstrasse 3

20097 Hamburg, Germany

Phone: (49) 40-2376-2286

Fax: (49) 40-2376-2232

Electronic Components & Devices

22-22 Nagaike-cho, Abeno-Ku

Osaka 545-8522, Japan

Phone: (81) 6-6621-1221

Fax: (81) 6117-725300/6117-725301

www.sharp-world.com

Fast Info: (1) 800-833-9437

www.sharpsma.com

www.sharpsme.com

TAIWAN

SINGAPORE

KOREA

SHARP Electronic Components

(Korea) Corporation

RM 501 Geosung B/D, 541

Dohwa-dong, Mapo-ku

Seoul 121-701, Korea

SHARP Electronic Components

(Taiwan) Corporation

8F-A, No. 16, Sec. 4, Nanking E. Rd.

Taipei, Taiwan, Republic of China

Phone: (886) 2-2577-7341

SHARP Electronics (Singapore) PTE., Ltd.

438A, Alexandra Road, #05-01/02

Alexandra Technopark,

Singapore 119967

Phone: (65) 271-3566

Phone: (82) 2-711-5813 ~ 8

Fax: (82) 2-711-5819

Fax: (886) 2-2577-7326/2-2577-7328

Fax: (65) 271-3855

CHINA

HONG KONG

SHARP Microelectronics of China

(Shanghai) Co., Ltd.

SHARP-ROXY (Hong Kong) Ltd.

3rd Business Division,

28 Xin Jin Qiao Road King Tower 16F

Pudong Shanghai, 201206 P.R. China

Phone: (86) 21-5854-7710/21-5834-6056

Fax: (86) 21-5854-4340/21-5834-6057

Head Office:

17/F, Admiralty Centre, Tower 1

18 Harcourt Road, Hong Kong

Phone: (852) 28229311

Fax: (852) 28660779

www.sharp.com.hk

No. 360, Bashen Road,

Xin Development Bldg. 22

Shenzhen Representative Office:

Room 13B1, Tower C,

Waigaoqiao Free Trade Zone Shanghai

200131 P.R. China

Electronics Science & Technology Building

Shen Nan Zhong Road

Email: smc@china.global.sharp.co.jp

Shenzhen, P.R. China

Phone: (86) 755-3273731

Fax: (86) 755-3273735


型号：	LQ295T3LZ31
厂家：	ETC
描述：	TFT Displays\|Product Specifications TFT显示器\|产品规格\n 显示器
文件：	总21页 (文件大小：582K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

LQ295T3LZ31 [ETC]

相关型号：

LQ310-14-.1-D

LQ310-14-.3-D

LQ310-16-.1-D

LQ310-16-.3-D

LQ310-18-.01-D

LQ310-18-.3-D

LQ310-20-.1-D

LQ315T3LZ49

LQ320

LQ325

LQ350

LQ370T3LZ39