OV8610
更新时间：2024-09-18 02:48:41
品牌：ETC
描述：COLOR | SVGA | 800 x 600 | DIGITAL | CameraChip | APPLICATION NOTE
概述
数据手册OV8610 概述
COLOR | SVGA | 800 x 600 | DIGITAL | CameraChip | APPLICATION NOTE
COLOR | SVGA | 800 ×600 |数码|的CameraChip |应用说明\n
OV8610 数据手册
通过下载OV8610数据手册来全面了解它。这个PDF文档包含了所有必要的细节，如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载mni isionTM
O
APPLICATION NOTE
OmniVision Serial Camera Control Bus (SCCB)
Functional Specification
Last Modified: 26 February 2003
Document Version: 2.1
Revision Number
Date
Revision
1.0
06/07/00
Initial Release
Nomenclature change entire document - SIO1 changed to SIO_C, SIO0
changed to SIO_D, SCS_ changed to SCCB_E
1.01
06/08/00
Inclusion of Section 3.5 documenting the 2-wire master/slave
2.0
2.1
03/08/02
02/26/03
TM
implementation where SCCB_E is not available in the CAMERACHIP
Incorporated into new template
This document is provided "as is" with no warranties whatsoever, including any warranty of merchantability, non-in-
fringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification, or
sample.
OmniVision Technologies, Inc. disclaims all liability, including liability for infringement of any proprietary
rights, relating to the use of information in this document. No license, expressed or implied, by estoppel
or otherwise, to any intellectual property rights is granted herein.
* Third-party brands, names, and trademarks are the property of their respective owners.
Note:
The information contained in this document is considered proprietary to OmniVision Technologies, Inc. This
information may be distributed only to individuals or organizations authorized by OmniVision Technologies, Inc. to
receive said information. Individuals and/or organizations are not allowed to re-distribute said information
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
00Table of Contents
Section 1, Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 2-Wire SCCB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 2, Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1
2.2
2.3
SCCB_E Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SIO_C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SIO_D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Section 3, Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1
3.2
3.3
3-Wire Data Transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmission Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Section 4, SCCB Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.1
4.2
4.3
4.4
Master Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Slave Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Conflict-Protection Resistors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Suspend Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Section 5, Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Section 6, Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
mni ision
O
00List of Figures
Figure 1-1
Figure 1-2
Figure 3-1
Figure 3-2
Figure 3-3
Figure 3-4
Figure 3-5
Figure 3-6
Figure 3-7
Figure 3-8
Figure 3-9
Figure 3-10
Figure 3-11
Figure 3-12
Figure 3-13
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
SCCB Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-Wire SCCB Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3-WIre Data Transmission Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3-Wire Start of Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3-Wire Stop of Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Transmission Phases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-Phase Write Transmission Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2-Phase Write Transmission Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2-Phase Read Transmission Cycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Phase 1 — ID Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Phase 2 — Sub-address (3-Phase Write Transmission) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Phase 2 — Read Data (2-Phase Read Transmission). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Phase 2 Sub-address Write Transmission/Phase 3 Write Data Transmission . . . . . . . . . . . . . . 13
Don’t-Care Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Suspend Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Block Diagram of the Master and Slaves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Conflict-Protection Resistor Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Conflict-Protection Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Suspend Circuit - PWDN Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Suspend Circuit - Switch Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
3
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
00List of Tables
Table 2-1
Table 2-2
Table 5-1
Master Device Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Slave Device Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SCCB Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Overview
mni ision
O
1 Overview
OmniVision Technologies, Inc. has defined and deployed the Serial Camera Control Bus (SCCB),
TM
a 3-wire serial bus, for control of most of the functions in OmniVision’s family of CAMERACHIPS
In reduced pin package parts, the SCCB operates in a modified 2-wire serial mode.
.
OmniVision CAMERACHIPS will only operate as slave devices and the companion back-end interface
must assert as the master. One SCCB master device can be connected to the SCCB to control at
least one SCCB slave device. An optional suspend-control signal provides the capability for the
SCCB master device to power down the SCCB system. Refer to Figure 1-1 for the SCCB functional
diagram illustrating the 3-wire connection.
Figure 1-1
SCCB Functional Block Diagram
SCCB_E
SIO_C
Master Device
Slave Device
Slave Device
SIO_D
Slave Device
1.1 2-Wire SCCB Interface
The modified 2-wire implementation allows for a SCCB master device to interface with only one
slave device. This 2-wire application is implemented in the CAMERACHIP reduced pin package
products where the SCCB_E signal is not available externally. Refer to Figure 1-2 for the functional
diagram of the 2-wire implementation for the SCCB interface.
Figure 1-2
2-Wire SCCB Functional Block Diagram
SIO_C
Master Device
SIO_D
Slave Device
The 2-wire implementation requires one of the following two master control methods in order to
facilitate the SCCB communication.
1. In the first instance, the master device must be able to support and maintain the data line of the
bus in a tri-state mode.
2. The alternate method if the master cannot maintain a tri-state condition of the data line is to
drive the data line either high or low and to note the transition there to assert communications
with the slave CAMERACHIP.
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
5
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
2 Pin Functions
Refer to Table 2-1 and Table 2-2 for pin descriptions of the master and slave devices, respectively,
used in SCCB communications.
Table 2-1.
Master Device Pin Descriptions
Signal Name
Signal Type
Description
Serial Chip Select Output - master drives SCCB_E at logical 1
when the bus is idle. Drives at logical 0 when the master asserts
transmissions or the system is in Suspend mode.
Serial I/O Signal 1 Output - master drives SIO_C at logical 1 when
the bus is idle. Drives at logical 0 and 1 when SCCB_E is driven
at 0. Drives at logical 0 when the system is Suspend mode.
a
Output
SCCB_E
SIO_C
Output
Serial I/O Signal 0 Input and Output - remains floating when the
bus is idle and drives to logical 0 when the system is in Suspend
mode.
I/O
SIO_D
PWDN
Output
Power down output
a. Where SCCB_E is not present on the CAMERACHIP, this signal is by default enabled and held high.
Table 2-2.
Slave Device Pin Descriptions
Signal Name
Signal Type
Description
Serial Chip Select Input - input pad can be shut down when the
a
SCCB_E
SIO_C
Input
system is in Suspend mode.
Serial I/O Signal 1 Input - input pad can be shut down when the
system is in Suspend mode.
Input
Serial I/O Signal 0 Input and Output - input pad can be shut down
when the system is in Suspend mode.
Power down input
I/O
SIO_D
PWDN
Input
a. Where SCCB_E is not present on the CAMERACHIP, this signal is by default enabled and held high.
2.1 SCCB_E Signal
The SCCB_E signal is a single-directional, active-low, control signal that must be driven by the
master device. It indicates the start or stop of the data transmission. A high-to-low transition of the
SCCB_E indicates a start of a transmission, while the low-to-high transition of the SCCB_E
indicates a stop of a transmission. SCCB_E must remain at logical 0 during a data transmission. A
logical 1 of SCCB_E indicates that the bus is idle.
2.2 SIO_C
The SIO_C signal is a single-directional, active-high, control signal that must be driven by the
master device. It indicates each transmitted bit. The master must drive SIO_C at logical 1 when the
bus is idle. A data transmission starts when SIO_C is driven at logical 0 after the start of
transmission. A logical 1 of SIO_C during a data transmission indicates a single transmitted bit.
Thus, SIO_D can occur only when SIO_C is driven at 0. The period of a single transmitted bit is
defined as tCYC as shown in Figure 3-8. The minimum of tCYC is 10 µs.
6
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Data Transmission
mni ision
O
2.3 SIO_D
The SIO_D signal is a bi-directional data signal that can be driven by either master or slave devices.
It remains floating, or tri-state, when the bus is idle. Maintenance of the signal is the responsibility
of both the master and slave devices in order to avoid propagating an unknown bus state.
Bus float and contention are allowed during transmissions of Don’t-Care or NA bits. The definition
of the Don’t-Care bit is described in Section 3.2.3. The master must avoid propagating an unknown
bus state condition when the bus is floating or conflicting. A conflict-protection resistor is required
to reduce static current when the bus conflicts. The connection of the conflict-protection resistor is
shown in Figure 4-2.
A single-bit transmission is indicated by a logical 1 of SIO_C. SIO_D can occur only when SIO_C
is driven at logical 0. However, an exception is allowed at the beginning and the end of a
transmission. During the period that SCCB_E is asserted and before SIO_C goes to 0, SIO_D can
be driven at 0. During the period that SIO_C goes to 1 and before SCCB_E is de-asserted, SIO_D
can also be driven at 0.
3 Data Transmission
3.1 3-Wire Data Transmission
A graphic overview of the SCCB 3-wire data transmission is shown in Figure 3-1. The SCCB
protocol allows for bus float and contention during data transmissions. Writing data to slaves is
defined as a write transmission, while reading data from slaves is defined as a read transmission.
Figure 3-1
3-WIre Data Transmission Timing Diagram
Start of
Stop of
Transmission
Transmission
SCCB_E
SIO_C
SIO_D
D7
D6
D5
D4
D3
D2
D1
D0
X
3.1.1 Start of Data Transmission
The start of data transmission in the 3-wire implementation is indicated by a high-to-low transition
of SCCB_E. Before asserting SCCB_E, the master must drive SIO_D at logical 1. This will avoid
propagating an unknown bus state before the transmission of data. After de-asserting SCCB_E, the
master must drive SIO_D at 1 for a defined period again to avoid unknown bus state propagation.
This period, tPSA, is defined as the post-active time of SCCB_E and has a minimum value of 0 µs.
Two timing parameters are defined for the start of transmission, tPRC and tPRA. The tPRC is defined
as the pre-charge time of SIO_D. This indicates the period that SIO_D must be driven at logical 1
prior to assertion of SCCB_E. The minimum value of tPRC is 15 ns. The tPRA is defined as the
pre-active time of SCCB_E. This indicates the period that SCCB_E must be asserted before SIO_D
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
7
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
is driven at logical 0. The minimum value of tPRA is 1.25 µs. The 3-wire start of transmission is
shown in Figure 3-2.
Figure 3-2
3-Wire Start of Data Transmission
Start of
Transmission
tPRA
SCCB_E
SIO_C
SIO_D
tPRC
3.1.2 Stop of Data Transmission
A stop of data transmission is indicated by a low-to-high transmission of SCCB_E. Two timing
parameters are defined for the stop of transmission, tPSC and tPSA. The tPSC is defined as
post-charge time of SIO_D. It indicates the period that SIO_D must remain at logical 1 after
SCCB_E is de-asserted. The minimum value of tPSC is 15 ns. The tPSA is defined as the post-active
time of SCCB_E. It indicates the period that SCCB_E must remain at logical 0 after SIO_D is
de-asserted. The minimum value of tPSA is 0 ns. The 3-wire stop of transmission is shown in
Figure 3-3.
Figure 3-3
3-Wire Stop of Data Transmission
Stop of
Transmission
tPSA
SCCB_E
SIO_C
tPSC
SIO_D
8
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Data Transmission
mni ision
O
3.2 Transmission Cycles
A basic element of a data transmission is called a phase. This section describes the three kinds of
transmissions:
•
•
•
3-Phase Write Transmission Cycle
2-Phase Write Transmission Cycle
2-Phase Read Transmission Cycle
3.2.1 Transmission Phases
A phase contains a total of 9 bits. The 9 bits consist of an 8-bit sequential data transmission followed
by a ninth bit (see Figure 3-4). The ninth bit is a Don’t-Care bit or an NA bit, depending on whether
the data transmission is a write or read. The maximum number of phases that can be included in a
transmission is three. The Most Significant Bit (MSB) is always asserted first for each phase.
Figure 3-4
Transmission Phases
7
6
5
4
3
2
1
0
X
7
6
5
4
3
2
1
0
X
7
6
5
4
3
2
1
0
X
Phase 1
Phase 2
Phase 3
Phase 1: ID Address
Phase 2: Sub-address / Read Data
Phase 3: Write Data
3.2.1.1 3-Phase Write Transmission Cycle
The 3-phase write transmission cycle (see Figure 3-5) is a full write cycle such that the master can
write one byte of data to a specific slave(s). The ID address identifies the specific slave that the
master intends to access. The sub-address identifies the register location of the specified slave.
The write data contains 8-bit data that the master intends to overwrite the content of this specific
address. The ninth bit of the three phases will be Don’t-Care bits.
Figure 3-5
3-Phase Write Transmission Cycle
ID Address
X
Sub-address
X
Write Data
X
Phase 1
Phase 2
Phase 3
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
9
OmniVision Serial Camera Control Bus (SCCB)
3.2.1.2 2-Phase Write Transmission Cycle
mni ision
O
The 2-phase write transmission cycle is followed by a 2-phase read transmission cycle. The
purpose of issuing a 2-phase write transmission cycle (see Figure 3-6) is to identify the sub-address
of some specific slave from which the master intends to read data for the following 2-phase read
transmission cycle. The ninth bit of the 2-phase write transmission will be Don’t-Care bits.
Figure 3-6
2-Phase Write Transmission Cycle
ID Address
X
Sub-address
X
Phase 1
Phase 2
3.2.1.3 2-Phase Read Transmission Cycle
There must be either a 3-phase or a 2-phase write transmission cycle asserted ahead of a 2-phase
read transmission cycle. The 2-phase read transmission cycle (see Figure 3-7) has no ability to
identify the sub-address. The 2-phase write transmission cycle contains read data of 8 bits and a
ninth Don’t-Care bit or NA bit. The master must drive the NA bit at logical 1.
Figure 3-7
2-Phase Read Transmission Cycle
ID Address
X
Read Data
NA
Phase 1
Phase 2
10
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Data Transmission
mni ision
O
3.2.2 Phase Descriptions
The following sections describe the individual phases found in the various transmission cycles.
3.2.2.1 Phase 1 — ID Address
Phase 1 is asserted by the master to identify the selected slave to which the data is read or written.
Each slave has a unique ID address. The ID address is comprised of seven bits, ordered from bit 7
to bit 1, and can identify up to 128 slaves. The eighth bit, bit 0, is the read/write selector bit that
specifies the transmission direction of the current cycle. A logical 0 represents a write cycle and a
logical 1 represents a read cycle.
The ninth bit of Phase 1 must be a Don’t-Care bit. SIO_D_OE_M_ and SIO_D_OE_S_ shown in
Figure 3-8 are internal active-low, I/O-enabled signals in the master and slave(s), respectively.
SIO_D_OE_S_ transaction occurs before the transition of SIO_D_OE_M_, as shown in Figure 3-8.
The master asserts the ID address, but de-asserts the ninth bit (Don’t-Care bit). The master must
mask the input of SIO_D during the period of the Don’t-Care bit and force the input to 0 to avoid
propagating an unknown bus state. The master continues asserting the following phases regardless
of the response to the Don’t-Care bit by the slave(s).
The SIO_OE_S is controlled by the slave(s) and may remain at logical 1 or be driven at logical 0.
The bus may be in a floating or conflicting status during the transmission of the Don’t-Care bit. In
this case, it is the slave’s responsibility to avoid propagating an unknown bus state.
A detailed description of the Don’t-Care bit is described in Section 3.2.3.
Figure 3-8
Phase 1 — ID Address
Phase 1
SCCB_E
tcyc
SIO_C
SIO_D
0: Write
1: Read
D7
D6
D5
D4
D3
D2
D1
R/W
X
D7
SIO0_OE_M_
SIO0_OE_S_
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
11
OmniVision Serial Camera Control Bus (SCCB)
3.2.2.2 Phase 2 — Sub-address/Read Data
mni ision
O
Either the master or the slave(s) may assert a phase 2 transmission. A phase 2 transmission
asserted by the master identifies the sub-address of the slave(s) the master intends to access. A
phase 2 transmission asserted by the slave(s) indicates the read data that the master will receive.
The slave(s) recognize the sub-address of this read data according to the previous 3-phase or
2-phase write transmission cycles.
The ninth bit is defined as a Don’t-Care bit when the master asserts phase 2. SIO_D_OE_M_ and
SIO_D_OE_S_ are the same as those defined under Section 3.2.2.1. The detailed timing is
illustrated in Figure 3-9.
Figure 3-9
Phase 2 — Sub-address (3-Phase Write Transmission)
Phase 2
SCCB_E
SIO_C
SIO_D
X
D7
D6
D5
D4
D3
D2
D1
D0
X
D7
SIO0_OE_M_
SIO0_OE_S_
The ninth bit is defined as an NA bit when the slave(s) assert the phase 2 transmission.
SIO_D_OE_M_ is de-asserted from the ninth bit of phase 1 and re-asserted for the NA bit. The
master is responsible for driving SIO_D at logical 1 during the period of the NA bit. Concurrently,
SIO_D_OE_S_ is asserted. The selected slave is responsible for driving SIO_D during the read
data period. Since SIO_D_OE_S_ is de-asserted before SIO_D_OE_M_ is asserted during the
period of the NA bit, bus float of SIO_D occurs when the master tries to drive the NA bit. The detailed
timing is shown in Figure 3-10.
Figure 3-10 Phase 2 — Read Data (2-Phase Read Transmission)
Phase 2
SCCB_E
SIO_C
SIO_D
SIO0_OE_M_
SIO0_OE_S_
X
D7
D6
D5
D4
D3
D2
D1
D0
12
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Data Transmission
mni ision
O
3.2.2.3 Phase 3 — Write Data
Only the master may assert the phase 3 transmission. The phase 3 transmission contains the actual
data the master intends to write to the slave(s). The timing diagram shown in Figure 3-11 applies to
both Phase 2 sub-address write transmissions and Phase 3 write data transmissions.
The ninth bit of the phase 3 transmission is defined as a Don’t-Care bit since the master is asserting
the transmission. SIO_D_OE_M_ and SIO_D_OE_S_ are the same as those defined for a phase 1
transmission.
Figure 3-11 Phase 2 Sub-address Write Transmission/Phase 3 Write Data Transmission
Phase 2/Phase 3
SCCB_E
SIO_C
X
D7
D6
D5
D4
D3
D2
D1
D0
X
SIO_D
SIO0_OE_M_
SIO0_OE_S_
3.2.3 Don’t-Care Bit
The Don’t-Care bit is the ninth bit of a master-issued transmission (ID address, sub-address, and
write data). The master will continue to assert transmission phases until the transmission cycle is
complete. The master also assumes that there is no transmission error during data transmissions.
The purpose of the Don’t-Care bit is to indicate the completion of the transmission.
When there is more than one slave on the bus, the slave(s) may respond to the Don’t-Care bit in
one of two ways. If slave 1 is selected and data is written to this specific slave, slave 1 will drive
SIO_D to logical 0 for the Don’t-Care bit. In this case, the SIO_D signal may conflict at the beginning
of the Don’t-Care bit, while it may be floating at the end of the Don’t-Care bit (see Figure 3-12).
Alternately, it is possible that the slave(s) do not respond to the Don’t-Care bit of the current phase.
In this situation, the SIO_D bus remains at float for the whole Don’t-Care bit.
The master does not check for transmission errors during data transmissions. There is a provision
for the slave(s) to record the status of the Don’t-Care bit in an internal register as shown in the
following example:
A slave(s) has defined a 1 byte register as the Don’t-Care Status register. The default value of the
Don’t-Care Status register is defined as 55. Assuming there are no errors during the data transmission,
this register value will remain unchanged. If the slave does not receive the Don’t-Care bit, the register
value will change to 54.
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
13
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
The master may query the Don’t-Care Status register to determine if there has been a transmission
of data. The master will issue an additional read transmission to the Don’t-Care Status register in
the target slave to check the value and, subsequently, determine if an error has occurred. This
scheme will not determine an error if the entire SCCB circuit has been corrupted.
SIO_D_OE_M_ can be de-asserted and re-asserted during the Don’t-Care bit transmission only
when SIO_C is driven to logical 0. The tmack is defined as the period of de-assertion of
SIO_D_OE_M_ prior to the low-to-high transition of SIO_C during the Don’t-Care bit transmission.
The period of re-assertion of SIO_D_OE_M_ after the high-to-low transmission is also defined as
t
mack. The minimum value of tmack is 1.25 µs.
If a slave intends to respond to the Don’t-Care bit, SIO_D_OE_S_ can be asserted and de-asserted
during the Don’t-Care bit transmission only when SIO_C is driven to logical 0. The tsack is defined
as the period of assertion of SIO_D_OE_S_ occurring after the high-to-low transition of SIO_C at
the beginning of the Don’t-Care bit transmission. The period of de-assertion of SIO_D_OE_S_
occurring after the high-to-low transition at the end of the Don’t-Care transmission is also defined
as tsack. The minimum value of tsack is 370 ns.
Figure 3-12 Don’t-Care Bit
SCCB_E
tmack
Conflict
Float
tmack
SIO_C
SIO_D
D0
X
D7
SIO0_OE_M_
SIO0_OE_S_
tsack
tsack
14
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Data Transmission
mni ision
O
3.3 Suspend Mode
Suspend mode (see Figure 3-13) is determined by the dedicated PWDN_ pin of the master. This is
achieved by the active-low output signal that specifies the suspension period as the master
attempts to power down the system. During the suspension period, SCCB_E, SIO_C, and SIO_D
are all driven to logical 0 by the master in order to avoid current leakage. There must be some time
for PWDN_ to be asserted prior to and be de-asserted after the assertion of SCCB_E, SIO_D, and
SIO_C. This parameter is defined as tsup. The minimum value of tsup is 50 ns. This scheme can
prevent logical errors from occurring in SCCB slaves.
The PWDN pin in slaves has the opposite polarity of the PWDN_ pin of the master. Two control
schemes for suspending the slave(s) are described in Section 4.4.
Figure 3-13 Suspend Mode
Suspend
PWDN_
SCCB_E
tsup
tsup
SIO_C
SIO_D
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
15
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
4 SCCB Structure
The structure of the SCCB system is shown in Figure 4-1. This diagram illustrates the connection
of one master with one slave. Multiple slaves may be connected on the same bus. A
conflict-protection resistor of SIO_D is required for each slave. Connection of conflict-protection
resistors for multiple slaves is illustrated in Figure 4-3.
Figure 4-1
Block Diagram of the Master and Slaves
PWDN_
PWDN
Master Device
SCCB_E
Slave Device
STBY
STBY
SIO_C
SCCB Master
SCCB Slave
SIO_D_OE_M_
SIO_D_OE_S_
SIO_D
STBY
4.1 Master Device
The master device drives both SCCB_E and SIO_C signals, while either the master or slave(s) can
drive the SIO_D signal. During the de-assertion of SCCB_E, the master must block the SIO_D input
to avoid propagating unknown bus conditions due to bus float. During the Don’t-Care bit
transmission, the master must ignore the status of SIO_D and keep asserting the subsequent
phases.
The PWDN_ is driven by the master to indicate the suspend mode cycle. As noted in Section 4.4,
there are two different ways to implement suspension circuits within the system.
4.2 Slave Devices
The slave(s) receive the SCCB_E and SIO_C signals from the master, while either the master or
the slave(s) can drive SIO_D. Input pads of the SCCB_E, SIO_C, and SIO_D signals contain the
standby (STBY) control terminal for reducing leakage current when the inputs are floating. Output
terminals of those input pads are driven at logical 1 when STBY is asserted. This can avoid logical
errors during suspend cycles.
16
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
SCCB Structure
mni ision
O
PWDN controls STBY of SCCB_E. This means the output terminal of the SCCB_E input pad is
driven at logical 1 during suspend mode cycles even though the master drives the input of SCCB_E
at 0.
The STBY control terminals of both SIO_C and SIO_D are controlled by PWDN and SCCB_E.
During suspend mode cycles and the de-assertion of SCCB_E, the output terminals of SIO_C and
SIO_D input pads are both driven at logical 1. During the Don’t-Care bit transmission, the slave(s)
must avoid propagating unknown bus conditions.
4.3 Conflict-Protection Resistors
Incorporating series resistors between SIO_D output of the master and the SIO_D input of the
slave(s) can avoid short circuits when bus contention occurs.
Figure 4-2
Conflict-Protection Resistor Connections
SIO_D
SIO_D
SIO_D
Master
Device
Slave
Device
Slave
Device
SIO_D
Device
Slave
Figure 4-3
Conflict-Protection Resistors
Master
1
Slave
0
Master
0
Slave
1
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
17
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
4.4 Suspend Circuits
There are two methods of issuance of a bus suspend cycle:
•
PWDN Mode
•
Switch Mode
4.4.1 PWDN Mode
The power pads of the slave(s) are always connected to VDD. The PWDN_ signal from the master
device needs to be inverted prior to connection to the slave(s) and the slave(s) circuit has an
opposite polarity. During normal operations, PWDN_ of the master is driven at logical 1 and the NPN
transistor is ON. In normal operation, the PWDN of the slave(s) is driven at logical 0. During the
suspend mode cycle, PWDN_ is driven at 0 and the NPN transistor is OFF. During the suspend
mode operation, the PWDN of the slave(s) is driven at 1. There is no leakage current during the
suspend cycle.
Figure 4-4
Suspend Circuit - PWDN Mode
SCCB_E
SIO_C
VDD
PWDN_
PWDN
VDD
Master Device
Slave Device
SIO_D
18
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Electrical Characteristics
mni ision
O
4.4.2 Switch Mode
The PWDN circuit of the slave(s) is always connected to logical 0. A power switch circuit is required
for each slave. The power of each slave is OFF during suspend mode cycles. In suspend mode
operation, there is no leakage current present as no power is provided to the slave(s).
Figure 4-5
Suspend Circuit - Switch Mode
SCCB_E
SIO_C
VDD
PWDN_
PWDN
VDD
Master Device
Slave Device
SIO_D
5 Electrical Characteristics
Table 5-1.
SCCB Electrical Characteristics
Symbol
Parameter
Condition
Min
10
Max
Unit
µs
t
t
t
t
t
t
t
t
Single bit transmission cycle time
Pre-charge time of SIO_D
Pre-active time of SCCB_E
Post-charge time of SIO_D
Post-active time of SCCB_E
SIO_D_OE_M_ transition time
SIO_D_OE_S_ transition time
PWDN_ pre/post-charge time
cyc
15
ns
prc
1.25
15
µs
pra
µs
psc
psa
mack
sack
sup
0
µs
1.25
370
50
µs
ns
ns
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
19
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
6 Terminology
Don’t-Care Bit:
ID Address:
Ninth bit of a Write phase.
Unique address of each device on the bus. The master asserts
the slave ID address to identify transmissions destined for the
slave device(s).
NA Bit:
Ninth bit of a Read phase.
Phases:
A phase contains a total of 9 bits consisting of a sequential
transmission of 8 data bits followed by a ninth Don’t-Care or NA
bit, depending on writes or reads.
Read Phases:
Phases that read data from slave(s).
Read Transmissions:
Master-asserted transmissions which read data from slave
device(s).
SCCB Data Transmissions: Transmissions consist of phases. All transmissions are initiated
by the master device. Start and stop of a transmission in the
3-wire system are indicated by the signaling of SCCB_E. Start
and stop of a transmission in the 2-wire system are indicated by
signaling of the SIO_D.
SCCB_E:
Serial bus enable/disable signal, previously denoted as SCS_,
SCCBB, and IICB in older documentation.
SCCB Master Device:
SCCB Slave Device(s):
An SCCB device that can assert SCCB transmissions. Only one
master is allowed in the system.
SCCB device(s) that can respond to an asserted SCCB
transmission. At least one slave can be connected to the
system.
SCCB System:
System consists of one master and at least one slave.
Serial Camera Control Bus: Typically, a 3-wire serial bus with an optional suspend-control
(SCCB)
signal. May be implemented in a 2-wire mode where required.
SIO_C:
Serial bus clock signal, previously denoted as SIO1 and SCL in
older documentation.
SIO_D:
Serial bus data signal, previously denoted as SIO0 and SDA in
older documentation.
20
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
Terminology
mni ision
O
Sub-address:
The master asserts the sub-address to indicate the specific
slave function/location to be accessed.
Suspend Mode:
Master-asserted suspend periods of device and/or system
suspension.
Transmission Cycles:
Transmission cycles include 3-phase write transmission cycle,
2-phase write transmission cycle, and 2-phase read
transmission cycle.
Write Transmissions:
Master-asserted transmissions which write data to slave
device(s).
Version 2.1, February 26, 2003
Proprietary to OmniVision Technologies
21
OmniVision Serial Camera Control Bus (SCCB)
mni ision
O
Note:
• All information shown herein is current as of the revision and publication date. Please refer
to the OmniVision web site (http://www.ovt.com) to obtain the current versions of all
documentation.
• OmniVision Technologies, Inc. reserves the right to make changes to their products or to
discontinue any product or service without further notice (It is advisable to obtain current product
documentation prior to placing orders).
• Reproduction of information in OmniVision product documentation and specifications is
permissible only if reproduction is without alteration and is accompanied by all associated
warranties, conditions, limitations and notices. In such cases, OmniVision is not responsible
or liable for any information reproduced.
• This document is provided with no warranties whatsoever, including any warranty of
merchantability, non-infringement, fitness for any particular purpose, or any warranty
otherwise arising out of any proposal, specification or sample. Furthermore, OmniVision
Technologies Inc. disclaims all liability, including liability for infringement of any proprietary
rights, relating to use of information in this document. No license, expressed or implied, by
estoppels or otherwise, to any intellectual property rights is granted herein.
• ‘OmniVision’, ‘CameraChip’ are trademarks of OmniVision Technologies, Inc. All other trade,
product or service names referenced in this release may be trademarks or registered trademarks of
their respective holders. Third-party brands, names, and trademarks are the property of their
respective owners.
For further information, please feel free to contact OmniVision at info@ovt.com.
OmniVision Technologies, Inc.
Sunnyvale, CA USA
(408) 733-3030
22
Proprietary to OmniVision Technologies
Version 2.1, February 26, 2003
OV8610 相关器件
| 型号 | 制造商 | 描述 | 价格 | 文档 |
| OV9121 | ETC | OV9625 Color CMOS SXGA (1.3 MPixel) CAMERACHIP OV9121 B&W CMOS SXGA (1.3 MPixel) CAMERACHIP | 获取价格 |
|
| OV9281 | OMNIVISION | automatic black level calibration (ABLC) | 获取价格 |
|
| OV9282 | OMNIVISION | automatic black level calibration (ABLC) | 获取价格 |
|
| OV9620 | ETC | COLOR | SXGA | 1280 x 1024 | DIGITAL | CameraChip | APPLICATION NOTE | 获取价格 |
|
| OV9625 | ETC | OV9625 Color CMOS SXGA (1.3 MPixel) CAMERACHIP OV9121 B&W CMOS SXGA (1.3 MPixel) CAMERACHIP | 获取价格 |
|
| OV9630 | ETC | COLOR | SXGA | 1280 x 1024 | DIGITAL | CameraChip | TECHNICAL BULLETIN | 获取价格 |
|
| OV9655 | OMNIVISION | ultimate 1/4 inch camera-on-a-chip | 获取价格 |
|
| OV9710 | OMNIVISION | high definition (HD) video CameraChip image sensor | 获取价格 |
|
| OV9712 | ETC | 获取价格 |
|
|
| OV9715 | OMNIVISION | High-Performance Video for Automotive Vision Applications | 获取价格 |
|
OV8610 相关文章
Bourns 密封通孔金属陶瓷微调电位计产品选型手册(英文版)
- 2024-09-20
- 6
Bourns 精密环境传感器产品选型手册(英文版)
- 2024-09-20
- 9
Bourns POWrTher 负温度系数(NTC)热敏电阻手册 (英文版)
- 2024-09-20
- 8
Bourns GMOV 混合过压保护组件产品选型手册(英文版)
- 2024-09-20
- 6
