PE7XXX03 [ETC]
RFI Filter Module Combines IEC Connector, Fusing;型号: | PE7XXX03 |
厂家: | ETC |
描述: | RFI Filter Module Combines IEC Connector, Fusing |
文件: | 总4页 (文件大小:166K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
PE7/PE8 Series
Specifications:
Rated Voltage: 250VAC Maximum - 50/60 Hz
Rated Current:
115VAC
3A
250VAC
3A
6A
6A
Current Overload: 6X for 8 Seconds
Hi-Pot Test (1 min):
Line to Ground
Line to Line
1500VAC
1768VDC
Insulation Resistance: 9 x 109 Ω at 100VDC
Ambient Temperature: 40°C Max. at Rated Current
Humidity Range: 0% to 95% R.H.
Termination:
• IEC Receptacle
• Wire Wrap/Solder
Maximum Leakage Current:
Each Line to Ground
115VAC, 60Hz:
PE7, PE 8
0.25mA
250VAC, 50Hz:
0.40mA
Voltage Select Card: Installed in 120VAC position
unless otherwise specified
Agency Approvals:
Refer to Page 55 for Ordering Instructions
Features:
• RFI Filter Module Combines IEC Connector, Fusing,
and Voltage Select Features in One Unit
• PE7 Series Filters Provide 20% More Differential Mode
Attenuation Than Comparable Units
• Accepts Either U.S. or European Standard Fuse Sizes
PE7 Series Simplified Schematic
110-220-
240 V
VOLTAGE
SELECTOR
SERIES-SERIES
FUSING
1-POLE
LINE
FOR TRANSFORMERS WITH TAP
LOAD
G
B
240V
220V
A
L
a
b
c
A
C
C
G
D
D
Voltage Contacts
d
e
110V
220V
240V
b,e
b,c
a
H
110V
E
N
E
F
F
2-POLE
2a
G
MINIMUM INSERTION LOSS - dB (50 ohm Circuit)
Frequency - MHz
Nominal
Current
Rating
Part
Number
Termination
Line/Load
MODE
.15
.50
1.0
5.0
10
30
PE7XXX03
PE8XXX03
IEC/Solder
Tabs
Common
Differential
18
8
24
18
30
24
45
46
45
50
50
40
3A
6A
PE7XXX06
PE8XXX06
IEC/Solder
Tabs
Common
Differential
10
8
19
18
24
24
39
39
44
40
50
40
Specifications subject to change.
Dimensions are shown for
reference purposes only.
52
www.curtisind.com
Curtis Industries
A Division of Powers Holdings, Inc.
PE7 Series Simplified Schematic
SERIES-PARALLEL
100-120-
220-240 V
VOLTAGE
SELECTOR
FUSING
1-POLE
FOR TRANSFORMERS WITH TWO SEPARATE
WINDINGS
LINE
LOAD
G
B
120V
100V
A
L
a
b
c
A
C
C
G
D
D
Voltage Contacts
d
e
120V
100V
120V
220V
240V
a,c,e
b,c,e
a,d
H
E
N
E
F
F
2-POLE
b,d
G
B
A
C
G
B
115V
A
L
a
b
c
C
G
D
D
Voltage Contacts
d
e
115V
115V
230V
a,b d,e
c
H
E
N
E
F
F
2-POLE
G
PE8 Series Simplified Schematic
ROCKER
FUSING
SWITCH
1-POLE
LOAD
LINE
1-POLE
1
1a
G
L
L
G
2
H
2a
N
N
2-POLE
2-POLE
G
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
53
Curtis Industries
1-800-657-0853
A Division of Powers Holdings, Inc.
PE7/PE8 Series(continued)
PE7/PE8
Snap-Mount Series
(3 and 6Amp) Dimensions
Refer to Page 55
2.266
(57,55)
for Standard
Mounting Cutouts
1.260
(32,0)
1.051
(26,70)
.22
(5,5)
2.283
(58,0)
.100
LOAD
LINE
(2,7) Q.C. Terminals All Locations
1.091
(27,71)
PE7/PE8
Screw-Mount Series
(3 and 6Amp) Dimensions
Refer to Page 55
for Standard
1.969
(50,0)
2.266
(57,55)
Mounting Cutouts
1.575
(40,0)
.22
(5,5)
1.051
(26,70)
1.142
(29,0)
2.283
(58,0)
.126
(3,20)
LINE
LOAD
Dia. Holes
.100
(2,7) Terminals Except Switch
1.091
(27,71)
Specifications subject to change.
Dimensions are shown for
reference purposes only.
54
www.curtisind.com
Curtis Industries
A Division of Powers Holdings, Inc.
How to Order
PE7
PE8
X
X
X
X
X
SERIES
PE = Power Entry
CURRENT RATING
3 = 3 AMP
6 = 6 AMP
OPTIONS
MOUNTING
(Consult Factory)
METHOD & FUSING
0 = Standard Units
0 = Snap Mount Metric Fuse
1 = Snap Mount U.S. Fuse
SWITCH
0 = No Switch
1 = SPST Rocker Switch
w/Q.C.
2 = DPST Rocker Switch
w/Q.C.
INSTALLATION INSTRUCTION
IMPORTANT – CHANGING
FUSE/VOLTAGE
2 = Snap Mount 2 Metric Fuse
3 = Snap Mount 2 U.S. Fuses
6 = Screw Mount Metric Fuse
7 = Screw Mount U.S. Fuse
8 = Screw Mount 2 Metric Fuses
9 = Screw Mount 2 U.S. Fuses
PE7/PE8
To change fuse, remove power cord
and open the front cover on the module.
Remove fuse holder and replace fuse.
Reinsert fuse holder and close cover.
To change the operating voltage on the
PE7 Series, remove the power cord and
open front cover. Rotate voltage select
wheel until desired voltage appears in
window of cover.
VOLTAGE SELECTOR
0 = No Selector (PE80 Series)
1 = 110-220-240 VAC
2 = 100-120-220-240 VAC
3 = 115-230 VAC
• Filter shipped without fuse.
Always use caution when selecting
and changing fuses and voltage
requirements. Curtis Industries is not
responsible for malfunction due to
improper installation/selection of fuse
and/or voltage select.
PE7/PE8 Screw Mount Series
PE7/PE8 Snap-Mount Series
2.20
(55,9)
.08
(2,0)
1.10
(27,9)
*See Below
2.20
(55,9)
R
1.575
(40,0)
1.122
(28,50)
1.122
(28,50)
*Panel Thickness
.031" - .079" use 2.20"
.080" - .125" use 2.22"
Cutout
.08
(2,0)
4-40
(M3)
R
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
55
Curtis Industries
1-800-657-0853
A Division of Powers Holdings, Inc.
相关型号:
PE80
SINGLE-PHASE FULL WAVE BRIDGE 1.5AMPERES THROUGH 5.0 AMPERES FOR P.C. BOARD AND POWER TERMINAL MOUNTING
EDI
PE8001
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 500 MHz to 1,000 MHz
PASTERNACK
PE8001-P
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 500 MHz to 1,000 MHz
PASTERNACK
PE8002
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 1 GHz to 2 GHz
PASTERNACK
PE8002-P
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 1 GHz to 2 GHz
PASTERNACK
PE8003
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 2 GHz to 4 GHz
PASTERNACK
PE8003-P
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 2 GHz to 4 GHz
PASTERNACK
PE8004
Biased Detector With 50 Ohm SMA Male to SMA Female Video Out Operating From 4 GHz to 8 GHz
PASTERNACK
©2020 ICPDF网 联系我们和版权申明