PI5C32X2383A [ETC]

Bus Exchanger ; 总线交换器\n
PI5C32X2383A
型号: PI5C32X2383A
厂家: ETC    ETC
描述:

Bus Exchanger
总线交换器\n

文件: 总4页 (文件大小:216K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
PI5C32X383/PI5C32X2383  
20-Bit Bus Switch/Exchange  
Product Features  
• Near-zero propagation delay  
Product Description  
PericomSemiconductor’sPI5Cseriesoflogiccircuitsarepro-duced  
in the Company’s advanced submicron CMOS technology,  
achieving industry leading performance.  
• Lownoise,25ohmversion(PI5C32X2383)  
• 5 ohm switches connect inputs to outputs (PI5C32X383)  
•
•
Direct bus connection when switches are ON  
The PI5C32X383 and PI5C32X2383 are 20-bit bus switches with  
exchange designed with a low ON resistance allowing inputs to be  
connected directly to outputs. The bus switch creates no additional  
propagationaldelayoradditionalgroundbouncenoise.Theswitches  
are turned ON by the Bus Enable (BE) input signal, and the Bus  
Exchange (BX) input signal offers nibble swapping of the AB and  
CD pairs of signals. This exchange configuration allows byte  
swapping of buses in systems. It can also be used as a quad  
2-to-1 multiplexer and to create low delay barrel shifters, etc. The  
PI5C32X2383isdesignedwithaninternal25ohmresistorreducing  
noise reflection in high-speed applications.  
Ultra-lowquiescentpower(0.2µAtypical)  
– Ideally suited for notebook applications  
• Packagesavailable:  
–48-pin240-milwidethinplasticTSSOP(A)  
–48-pin150-milwideplasticQSOP(B)  
Product Pin Configuration  
48  
47  
46  
45  
44  
43  
42  
41  
40  
39  
38  
37  
BE1  
C0  
A0  
B0  
D0  
C1  
A1  
B1  
D1  
1
2
3
4
5
6
7
8
9
VCC  
D4  
B4  
Applications  
10-wide 2:1 MUX, Byte Swapping, and Hot Insertion.  
A4  
C4  
D3  
B3  
Truth Table(1)  
Function  
Disconnect  
Connect  
BEN  
H
BXn  
X
A0-A9  
Hi-Z  
B0-B9  
Hi-Z  
A3  
C3  
D2  
B2  
C2 10  
A2 11  
GND 12  
BE2 13  
C5 14  
A5 15  
B5 16  
D5 17  
C6 18  
A6 19  
B6 20  
D6 21  
C7 22  
A7 23  
GND 24  
L
L
C0-C9  
D0-D9  
D0-D9  
C0-C9  
48-Pin  
Exchange  
L
H
BX1  
Note: 1. H = High Voltage Level, X = Don’t Care,  
L = Low Voltage Level, Hi-Z = High Impedance  
36 VCC  
35 D9  
34 B9  
33 A9  
32 C9  
31 D8  
30 B8  
Logic Block Diagram  
A5  
B5  
C5  
D5  
A0  
C0  
D0  
A8  
29  
28  
27  
26  
25  
C8  
D7  
B7  
B0  
BX2  
A9  
B9  
C9  
D9  
A4  
B4  
C4  
D4  
Product Pin Description  
Pin Name  
BEn  
BXn  
Ax  
Description  
Bus Enable Input (Active LOW)  
Bus Exchange Input  
Bus A  
Bx  
Bus B  
BX1  
Cx  
Bus C  
BE1  
BX2  
Dx  
Bus D  
GND  
VCC  
Ground  
BE2  
Power  
PS8100  
07/10/97  
1
PI5C32X383/PI5C32X2383  
20-Bit Bus Switch/Exchange  
Maximum Ratings  
(Above which the useful life may be impaired. For user guidelines, not tested.)  
Note:  
Storage Temperature ....................................................................–65°C to +150°C  
Ambient Temperature with Power Applied .................................. –40°C to +85°C  
Supply Voltage to Ground Potential (Inputs & Vcc Only) .......... –0.5V to +7.0V  
Supply Voltage to Ground Potential (Outputs & D/O Only) ....... –0.5V to +7.0V  
DC Input Voltage ........................................................................... –0.5V to +7.0V  
DC Output Current....................................................................................... 120mA  
Power Dissipation ........................................................................................... 0.5W  
Stresses greater than those listed under MAXIMUM  
RATINGS may cause permanent damage to the  
device. This is a stress rating only and functional  
operation of the device at these or any other condi-  
tions above those indicated in the operational sec-  
tions of this specification is not implied. Exposure to  
absolute maximum rating conditions for extended  
periods may affect reliability.  
DC Electrical Characteristics (Over the Operating Range, TA = –40°C to +85°C, VCC = 5V ±5%)  
Parameters Description  
TestConditions(1)  
Min.  
2.0  
–0.5  
—
Typ(2) Max.  
Units  
V
VIH  
VIL  
IIH  
InputHIGHVoltage  
GuaranteedLogicHIGHLevel  
GuaranteedLogicLOWLevel  
VCC =Max.,VIN =VCC  
—
—
—
0.8  
±1  
Input LOW Voltage  
V
InputHIGHCurrent  
—
µA  
µA  
µA  
V
IIL  
Input LOW Current  
VCC =Max.,VIN =GND  
AB, CD­VCC  
—
—
±1  
IOZH  
VIK  
IOS  
VH  
High Impedance Output Current  
—
—
±1  
ClampDiodeVoltage  
VCC =Min., IIN = –18mA  
AB(CD)=0V,CD(AB)=VCC  
—
–0.7  
—
–1.2  
—
Short Circuit Current(3)  
Input Hysteresis at Control Pins  
Switch On Resistance(4)  
100  
—
mA  
mV  
ohm  
150  
—
RON  
VCC =Min.,VIN = 0.0V,  
ION =48mA  
PI5C3383  
PI5C32383  
—
18  
5
7
28  
40  
VCC =Min.,VIN = 2.4V,  
ION =15mA  
PI5C3383  
PI5C32383  
—
18  
10  
35  
15  
48  
ohm  
Capacitance (TA = 25°C, f = 1 MHz)  
Parameters(5)  
Description  
Test Conditions  
Typ  
Max.  
Units  
CIN  
Input Capacitance  
VIN = 0V  
VIN = 0V  
—
—
6
6
pF  
pF  
COFF  
AB/CD Capacitance, Switch Off  
CON  
AB/CD Capacitance, Switch On  
VIN = 0V  
—
8
pF  
Notes:  
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.  
2. Typical values are at Vcc = 5.0V, TA = 25°C ambient and maximum loading.  
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.  
4. Measured by the voltage drop between AB and CD pin at indicated current through the switch. ON resistance is determined by  
the lower of the voltages on the two (A or B, C or D) pins.  
5. This parameter is determined by device characterization but is not production tested.  
PS8100  
07/10/97  
2
PI5C32X383/PI5C32X2383  
20-Bit Bus Switch/Exchange  
Power Supply Characteristics  
Parameters Description  
Test Conditions(1)  
Min. Typ(2) Max. Units  
ICC  
Quiescent Power  
Supply Current  
VCC = Max.  
VIN = GND or VCC  
—
—
—
0.1  
—
—
3.0  
µA  
ICC  
ICCD  
Supply Current per  
Input @ TTL HIGH  
VCC = Max.  
VIN = 3.4V(3)  
2.5  
mA  
Supply Current per  
Input per MHz(4)  
VCC = Max.,  
AB and CD Pins Open  
BE = GND  
0.25  
mA/  
MHz  
Control Input Toggling  
50% Duty Cycle  
Notes:  
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.  
2. Typical values are at Vcc = 5.0V, +25°C ambient.  
3. Per TTL driven input (VIN = 3.4V, control inputs only); A, B, C, and D pins do not contribute to Icc.  
4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified  
frequency. The A, B, C, and D inputs generate no significant AC or DC currents as they transition. This parameter is not tested,  
but is guaranteed by design.  
PI5C32X383 Switching Characteristics over Operating Range  
PI5C32X383  
Com  
Parameters Description  
Conditions(1)  
Min.  
Typ  
Max.  
Units  
tPLH  
tPHL  
tPZH  
tPZL  
tPHZ  
tPLZ  
tBX  
Propagation Delay(2,3)  
AxtoCx,BxtoDx  
BusEnableTime  
BEtoCxorDx  
Bus Disable Time  
BE to Cx or Dx  
Bus Exchange Time  
BX to Cx or Dx  
CL = 50pF  
RL = 500ohm  
—
0.25  
—
1.5  
1.5  
1.5  
—
—
—
6.5  
5.5  
6.5  
ns  
Notes:  
1. See test circuit and waveforms.  
2. This parameter is guaranteed but not tested on Propagation Delays.  
3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch  
and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since  
this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little  
propagational delay to the system. Propagational delay of the bus switch when used in a system is determined  
by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.  
PS8100  
07/10/97  
3
PI5C32X383/PI5C32X2383  
20-Bit Bus Switch/Exchange  
PI5C32X2383 Switching Characteristics over Operating Range  
PI5C32X2383  
Com  
Parameters Description  
Conditions(1)  
Min.  
Typ  
Max.  
Units  
tPLH  
tPHL  
tPZH  
tPZL  
tPHZ  
tPLZ  
tBX  
Propagation Delay(2,3)  
AxtoCx,BxtoDx  
BusEnableTime  
BEtoCxorDx  
Bus Disable Time  
BE to Cx or Dx  
Bus Exchange Time  
BX to Cx or Dx  
CL = 50 pF  
RL =500ohm  
—
1.25  
—
1.5  
1.5  
1.5  
—
—
—
6.5  
5.5  
6.5  
ns  
Notes:  
1. See test circuit and waveforms.  
2. This parameter is guaranteed but not tested on Propagation Delays.  
3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance  
of the switch and the load capacitance. The time constant for the switch alone is of the order of  
0.25 ns for 50 pF load. Since this time constant is much smaller than the rise/fall times of typical  
driving signals, it adds very little propagational delay to the system. Propagational delay of the  
bus switch when used in a system is determined by the driving circuit on the driving side of the  
switch and its interaction with the load on the driven side.  
Pericom Semiconductor Corporation  
2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com  
PS8100  
07/10/97  
4

相关型号:

PI5C32X2383B

Bus Exchanger
ETC

PI5C32X2384

20-Bit Bus Switch with 25W Series Resistor
PERICOM

PI5C32X2384A

Bus Switch
ETC

PI5C32X2384B

Bus Switch
ETC

PI5C32X2384BX

Bus Driver, CBT/FST/QS/5C/B Series, 4-Func, 5-Bit, True Output, CMOS, PDSO48, 0.150 INCH, PLASTIC, BQSOP-48
PERICOM

PI5C32X245

16-Bit, 2-Port BusSwitch
PERICOM

PI5C32X245B

16-Bit, 2-Port BusSwitch
PERICOM

PI5C32X245BE

16-Bit, 2-Port BusSwitch
PERICOM

PI5C32X245BE

Bus Driver, CBT/FST/QS/5C/B Series, 2-Func, 8-Bit, True Output, CMOS, PDSO40, 0.150 INCH, GREEN, PLASTIC, BQSOP-40
DIODES

PI5C32X245BEX

Bus Driver, CBT/FST/QS/5C/B Series, 2-Func, 8-Bit, True Output, PDSO40, 0.150 INCH, GREEN, PLASTIC, BQSOP-40
DIODES

PI5C32X245BEX

Bus Driver, CBT/FST/QS/5C/B Series, 2-Func, 8-Bit, True Output, PDSO40, 0.150 INCH, GREEN, PLASTIC, BQSOP-40
PERICOM

PI5C32X245BX

Bus Driver, CBT/FST/QS/5C/B Series, 2-Func, 8-Bit, True Output, PDSO40, 0.150 INCH, PLASTIC, BQSOP-40
PERICOM