SJ-A2872-FREQ [ETC]
CRYSTAL CLOCK OSCILLATORS; 晶体时钟振荡器
| 型号： | SJ-A2872-FREQ |
| 厂家： | 
ETC |
| 描述： | CRYSTAL CLOCK OSCILLATORS |
| 文件： | 总2页 (文件大小：263K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Data Sheet 9938A
CRYSTAL CLOCK OSCILLATORS
Rev. L
Differential Positive ECL (DPECL)
SJ-A2870 Series
Description
The SJ-A2870 Series of quartz crystal oscillators provide MECL 10K and 10KH series compatible signals in
a ceramic SMD package. Systems designers may now specify space-saving, cost-effective packaged
PECL oscillators to meet their timing requirements.
Features
• Wide frequency range–18.0MHz to 250.0MHz
• User specified tolerance available
• Low Jitter - Wavecrest jitter characterization
available
• Will withstand vapor phase temperatures of 253°C • High Reliability - NEL HALT/HASS qualified for
for 4 minutes maximum
• Space-saving alternative to discrete component
oscillators
crystal oscillator start-up conditions
• High Q Crystal actively tuned oscillator circuit
• Power supply decoupling internal
• High shock resistance, to 3000g
• 3.3 volt operation
• Metal lid electrically connected to ground to
reduce EMI
• No internal PLL avoids cascading PLL problems
• High frequencies due to proprietary design
• Gold plated leads - Solder dipped leads available
upon request
• MECL 10K and 10KH series compatible output on
Pin 3, complement on Pin 1
Electrical Connection
Pin
Connection
1
2
3
4
Output Complement
VEE /Ground
Output
VCC
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: nelsales@nelfc.com www.nelfc.com
Data Sheet 9938A
CRYSTAL CLOCK OSCILLATORS
Rev. L
SJ-A2870 Series Continued
Differential Positive ECL (DPECL)
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter
Frequency
Symbol
-----
-----
VOL
VOH
Conditions
-----
@ VCC-1.29V
-----
Min
Typical
Max
18.0MHz
45/55%
1.35V
2.28V
-----
-----
-----
-----
1.0 ns
-----
-----
-----
250.0MHz
55/45%
1.70V
2.56V
1.5 ns
+0.5 ns
3 psec
+100ppm
Duty Cycle
Logic 0 (2)
Logic 1(2)
-----
Rise & Fall Time
tr,tf 20-80%VO with 50 ohm load to VCC-2V -----
Tpd (4)
-----
-----
dF/F
-----
-----
-0.5 ns
-----
-100ppm
Jitter, RMS(3)
Frequency Stability (1)
Overall conditions including:
voltage, calibration, temp.,
10 yr aging, shock, vibration
General Characteristics
Parameter
Supply Voltage
Supply Current
Symbol
VCC
ICC
Conditions
-----
50 ohm termination
To 2.00V below VCC
Min
3.15V
0.0 mA
Typical
3.3V
-----
Max
3.45V
80 mA
Output current
IO
Low level Output Current 0.0 mA
-----
-----
-----
-----
-----
±50.0 mA
70°C
125°C
276 mW
300°C
Operating temperature
Storage temperature
Power Dissipation
Lead temperature
Load
TA
TS
PD
TL
------
-----
-----
0°C
-55°C
-----
Soldering, 10 sec.
-----
50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required
tS ----- -----
Start-up time
2 ms
10 ms
Environmental and Mechanical Characteristics
Mechanical Shock
Thermal Shock
Vibration
Soldering Condition
Hermetic Seal
ESD Sensitivity
Per MIL-STD-202, Method 213, Condition E
Per MIL-STD-833, Method 1011, Condition A
0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
300°C for 10 seconds
Leak rate less than 1 x 10 -8 atm.cc/sec of helium
Human Body Model per ON Semiconductor 10kH series ECL: 500V min.
Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) VOL, VOH, referenced to ground (VEE) with VCC = 3.3V
3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization.
4) Tpd is phase shift between the falling edge of pin 3 at VCC-1.29V and rising edge of pin 1 at VCC-1.29V.
Creating a Part Number
SJ - A287X - FREQ
Package Code
SJ 4 J Lead SMD
Tolerance/Performance
0 ±100ppm 0-70°C
1 ±50ppm 0-70°C
7 ±25ppm 0-70°C
Input Voltage
Code Specification
9 Customer Specific
A ±20ppm 0-70°C
A
3.3V
5V
B ±50ppm -40 to +85°C
C ±100ppm -40 to +85°C
357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: nelsales@nelfc.com www.nelfc.com
相关型号：
©2020 ICPDF网 联系我们和版权申明