ST6262BB1/XXX [ETC]
MICROCONTROLLER|8-BIT|ST6200 CPU|CMOS|DIP|16PIN|PLASTIC ; 微控制器| 8位| ST6200 CPU | CMOS | DIP | 16PIN |塑料\n
| 型号： | ST6262BB1/XXX |
| 厂家： | 
ETC |
| 描述： | MICROCONTROLLER|8-BIT|ST6200 CPU|CMOS|DIP|16PIN|PLASTIC
|
| 文件： | 总78页 (文件大小：519K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ST62T52C
ST62T62C/E62C
8-BIT OTP/EPROM MCUs WITH A/D CONVERTER,
SAFE RESET, AUTO-RELOAD TIMER AND EEPROM
■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +125°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
User selectable size
■ Data RAM: 128 bytes
■ Data EEPROM: 64 bytes (none on ST62T52C)
■ User Programmable Options
PDIP16
■ 9 I/O pins, fully programmable as:
– Input with pull-up resistor
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
PSO16
■ 5 I/O lines can sink up to 30mA to drive LEDs or
TRIACs directly
■ 8-bit Timer/Counter with 7-bit programmable
prescaler
■ 8-bit Auto-reload Timer with7-bit programmable
prescaler (AR Timer)
SSOP16
■ Digital Watchdog
■ Oscillator Safe Guard
■ Low Voltage Detector for Safe Reset
■ 8-bit A/D Converter with 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
Crystal Ceramic resonator or RC network
■ User configurable Power-on Reset
■ One external Non-Maskable Interrupt
■ ST626x-EMU2 Emulation and Development
System (connects to an MS-DOS PC via a
parallel port)
CDIP16W
(See end of Datasheet for Ordering Information)
DEVICE SUMMARY
EPROM
(Bytes)
OTP
(Bytes)
DEVICE
EEPROM
ST62T52C
ST62T62C
ST62E62C
1836
1836
-
64
64
1836
Rev. 3.0
February 2002
1/78
Table of Contents
Document
Page
ST62T52C
ST62T62C/E62C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3.2 Program Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.3 Data Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.4 Stack Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.3.5 Data Window Register (DWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3.6 Data RAM/EEPROM Bank Register (DRBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.3.7 EEPROM Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.4 PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.4.1 Option Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.4.2 Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.4.3 . EEPROM Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . 18
3.1 CLOCK SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.1 Main Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.2 Low Frequency Auxiliary Oscillator (LFAO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.1.3 Oscillator Safe Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.1 RESET Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.2 Power-on Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2.3 Watchdog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.4 LVD Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.5 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2.6 MCU Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3 DIGITAL WATCHDOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.3.1 Digital Watchdog Register (DWDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.3.2 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4.1 Interrupt request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4.2 Interrupt Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4.3 Interrupt Option Register (IOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.4.4 Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.5 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.5.1 WAIT Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.5.2 STOP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
78
3.5.3 Exit from WAIT and STOP Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2/78
Table of Contents
Document
Page
4 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1.1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.1.2 Safe I/O State Switching Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.1.3 ARTimer alternate functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2 TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2.1 Timer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.2 Timer Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.3 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.4 Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3 AUTO-RELOAD TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3.1 AR Timer Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3.2 Timer Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3.3 AR Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.4 A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.4.1 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5 SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.1 ST6 ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.2 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.3 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.1 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.2 RECOMMENDED OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
6.3 DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.4 AC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.5 A/D CONVERTER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.6 TIMER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.7 SPI CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.8 ARTIMER ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
7 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.2 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
ST62P52C
ST62P62C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
1 GENERAL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
1.2 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
1.2.1 Transfer of Customer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
1.2.2 Listing Generation and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
3/78
Table of Contents
Document
Page
ST6252C
ST6262B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
1 GENERAL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
1.2 ROM READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
1.3 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
1.3.1 Transfer of Customer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
1.3.2 Listing Generation and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2 SUMMARY OF CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
78
4/78
ST62T52C ST62T62C/E62C
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
The ST62T52C and ST62T62C devices is low cost
members of the ST62xx 8-bit HCMOS family of mi-
crocontrollers, which is targeted at low to medium
complexity applications. All ST62xx devices are
based on a building block approach: a common
core is surrounded by a number of on-chip periph-
erals.
fined in the programmable option byte of the
OTP/EPROM versions.
OTP devices offer all the advantages of user pro-
grammability at low cost, which make them the
ideal choice in a wide range of applications where
frequent code changes, multiple code versions or
last minute programmability are required.
The ST62E62C is the erasable EPROM version of
the ST62T62C device, which may be used to em-
ulate the ST62T52C and ST62T62C devices as
well as the ST6252C and ST6262B ROM devices.
These compact low-cost devices feature a Timer
comprising an 8-bit counter and a 7-bit program-
mable prescaler, an 8-bit Auto-Reload Timer,
EEPROM data capability (except ST62T52C), an
8-bit A/D Converter with4 analog inputs and a Dig-
ital Watchdog timer, making them well suited for a
wide range of automotive, appliance and industrial
applications.
OTP and EPROM devices are functionally identi-
cal. The ROM based versions offer the same func-
tionality selecting as ROM options the options de-
Figure 1. Block Diagram
8-BIT
PA4..PA5 / Ain
PORT A
PORT B
A/D CONVERTER
TEST/V
PP
TEST
PB0, PB2..PB3 / 30 mA Sink
PB6 / ARTimin / 20 mA Sink
PB7 / ARTimout / 20 mA Sink
NMI
INTERRUPT
DATA ROM
USER
SELECTABLE
PORT C
PC2..PC3 / Ain
PROGRAM
MEMORY
DATA RAM
128 Bytes
AUTORELOAD
TIMER
1836 bytes OTP
(ST62T52C, T62C)
1836 bytes EPROM
(ST62E62C)
DATA EEPROM
64 Bytes
TIMER
(ST62T62C/E62C)
PC
STACK LEVEL 1
STACK LEVEL 2
STACK LEVEL 3
STACK LEVEL 4
STACK LEVEL 5
STACK LEVEL 6
DIGITAL
WATCHDOG
8 BIT CORE
POWER
RESET
RESET
OSCILLATOR
SUPPLY
V
V
OSCin OSCout
DD SS
5/78
ST62T52C ST62T62C/E62C
1.2 PIN DESCRIPTIONS
V
and V . Power is supplied to the MCU via
Mout are either Port B I/O bits or the Input and
Output pins of the ARTimer.
DD
SS
these two pins. V
is the power connection and
DD
V
is the ground connection.
Reset state of PB2-PB3 pins can be defined by op-
tion either with pull-up or high impedance.
SS
OSCin and OSCout. These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
PB0, PB2-PB3, PB6-PB7 scan also sink 30mA for
direct LED driving.
PC2-PC3. These 2 lines are organized as one I/O
port (C). Each line may be configured under soft-
ware control as input with or without internal pull-
up resistor, interrupt generating input with pull-up
resistor, analog input for the A/D converter, open-
drain or push-pull output.
RESET. The active-low RESET pin is used to re-
start the microcontroller.
TEST/VPP. The TEST must be held at VSS for nor-
mal operation. If TEST pin is connected to a
+12.5V level during the reset phase, the
EPROM/OTP programming Mode is entered.
Figure 2. ST62T52C, E62C and T62C Pin
Configuration
NMI. The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. The NMI input is
falling edge sensitive. It is provided with an on-chip
pullup resistor (if option has been enabled), and
Schmitt trigger characteristics.
PB0
PC2/Ain
PC3/Ain
1
2
3
4
5
6
7
8
16
15
V
/TEST
PB2
PP
14
13
NMI
PB3
RESET
PA4-PA5. These 2 lines are organized as one I/O
port (A). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, interrupt generating inputs with pull-
up resistors, open-drain or push-pull outputs, ana-
log inputs for the A/D converter.
12
11
ARTIMin/PB6
ARTIMout/PB7
OSCout
OSCin
V
DD
PA5/Ain
PA4/Ain
10
9
PB0, PB2-PB3, PB6-PB7. These 5 lines are or-
ganized as one I/O port (B). Each line may be con-
figured under software control as inputs with or
without internal pull-up resistors, interrupt generat-
ing inputs with pull-up resistors, open-drain or
push-pull outputs. PB6/ARTIMin and PB7/ARTI-
V
SS
6/78
ST62T52C ST62T62C/E62C
1.3 MEMORY MAP
1.3.1 Introduction
Briefly, Program space contains user program
code in OTP and user vectors; Data space con-
tains user data in RAM and in OTP, and Stack
space accommodates six levels of stack for sub-
routine and interrupt service routine nesting.
The MCU operates in three separate memory
spaces: Program space, Data space, and Stack
space. Operation in these three memory spaces is
described in the following paragraphs.
Figure 3. Memory Addressing Diagram
PROGRAM SPACE
DATA SPACE
0000h
000h
RAM / EEPROM
BANKING AREA
0-63
03Fh
040h
DATA READ-ONLY
WINDOW
MEMORY
PROGRAM
MEMORY
07Fh
080h
081h
082h
083h
084h
X REGISTER
Y REGISTER
V REGISTER
W REGISTER
RAM
DATA READ-ONLY
MEMORY
WINDOW SELECT
0C0h
0FF0h
DATA RAM
INTERRUPT &
RESET VECTORS
0FFFh
BANK SELECT
ACCUMULATOR
0FFh
7/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
1.3.2 Program Space
Program Space comprises the instructions to be
executed, the data required for immediate ad-
dressing mode instructions, the reserved factory
test area and the user vectors. Program Space is
addressed via the 12-bit Program Counter register
(PC register).
Figure 4. ST62T52C/T62C Program
Memory Map
0000h
1.3.2.1 Program Memory Protection
The Program Memory in OTP or EPROM devices
can be protected against external readout of mem-
ory by selecting the READOUT PROTECTION op-
tion in the option byte.
*
RESERVED
In the EPROM parts, READOUT PROTECTION
option can be disactivated only by U.V. erasure
that also results into the whole EPROM context
erasure.
Note: Once the Readout Protection is activated, it
is no longer possible, even for STMicroelectronics,
to gain access to the OTP contents. Returned
parts with a protection set can therefore not be ac-
cepted.
087Fh
0880h
USER
PROGRAM MEMORY
1836 BYTES
(OTP/EPROM)
0F9Fh
0FA0h
0FEFh
*
RESERVED
0FF0h
0FF7h
INTERRUPT VECTORS
0FF8h
0FFBh
RESERVED
0FFCh
0FFDh
NMI VECTOR
0FFEh
0FFFh
USER RESET VECTOR
(*) Reserved areas should be filled with 0FFh
8/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
1.3.3 Data Space
Table 2. ST62T52C, T62C and ST62E62C Data
Memory Space
Data Space accommodates all the data necessary
for processing the user program. This space com-
prises the RAM resource, the processor core and
peripheral registers, as well as read-only data
such as constants and look-up tables in
OTP/EPROM.
000h
RAM / EEPROM banks
03Fh
040h
DATA ROM WINDOW AREA
07Fh
1.3.3.1 Data ROM
X REGISTER
Y REGISTER
V REGISTER
W REGISTER
080h
081h
082h
083h
084h
All read-only data is physically stored in program
memory, which also accommodates the Program
Space. The program memory consequently con-
tains the program code to be executed, as well as
the constants and look-up tables required by the
application.
DATA RAM 60 BYTES
0BFh
0C0h
0C1h
0C2h
0C3h
0C4h
0C5h
0C6h
0C7h
0C8h*
0C9h*
0CAh
0CBh
0CCh
0CDh
0CEh
0CFh
0D0h
0D1h
0D2h
0D3h
0D4h
0D5h
0D6h
0D7h
0D8h
0D9h
0DAh
0DBh
0DCh
0DDh
0DEh
0E7h
0E8h*
0E9h
0EAh
0EBh
0FEh
0FFh
PORT A DATA REGISTER
PORT B DATA REGISTER
PORT C DATA REGISTER
RESERVED
The Data Space locations in which the different
constants and look-up tables are addressed by the
processor core may be thought of as a 64-byte
window through which it is possible to access the
read-only data stored in OTP/EPROM.
PORT A DIRECTION REGISTER
PORT B DIRECTION REGISTER
PORT C DIRECTION REGISTER
RESERVED
INTERRUPT OPTION REGISTER
DATA ROM WINDOW REGISTER
1.3.3.2 Data RAM/EEPROM
In ST62T52C, T62C and ST62E62C devices, the
data space includes 60 bytes of RAM, the accu-
mulator (A), the indirect registers (X), (Y), the short
direct registers (V), (W), the I/O port registers, the
peripheral data and control registers, the interrupt
option register and the Data ROM Window register
(DRW register).
RESERVED
PORT A OPTION REGISTER
PORT B OPTION REGISTER
PORT C OPTION REGISTER
RESERVED
A/D DATA REGISTER
A/D CONTROL REGISTER
Additional RAM and EEPROM pages can also be
addressed using banks of 64 bytes located be-
tween addresses 00h and 3Fh.
TIMER PRESCALER REGISTER
TIMER COUNTER REGISTER
TIMER STATUS CONTROL REGISTER
AR TIMER MODE CONTROL REGISTER
AR TIMER STATUS/CONTROLREGISTER1
AR TIMER STATUS/CONTROLREGISTER2
WATCHDOG REGISTER
AR TIMER RELOAD/CAPTURE REGISTER
AR TIMER COMPARE REGISTER
AR TIMER LOAD REGISTER
1.3.4 Stack Space
Stack space consists of six 12-bit registers which
are used to stack subroutine and interrupt return
addresses, as well as the current program counter
contents.
Table 1. Additional RAM / EEPROM Banks
Device
ST62T52C
ST62T62C
RAM
EEPROM
-
RESERVED
1 x 64 bytes
1 x 64 bytes
1 x 64 bytes
DATA RAM/EEPROM REGISTER
RESERVED
EEPROM CONTROL REGISTER
RESERVED
ACCUMULATOR
* WRITE ONLY REGISTER
9/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
1.3.5 Data Window Register (DWR)
Data Window Register (DWR)
Address: 0C9h
— Write Only
The Dataread-only memorywindow is located from
address 0040h to address 007Fh in Data space. It
allows direct reading of 64 consecutivebytes locat-
ed anywhere in program memory, between ad-
dress 0000h and 0FFFh (top memory address de-
pends on the specific device). All the program
memory can therefore be used to store either in-
structions or read-only data. Indeed, the window
can be moved in steps of 64 bytes along the pro-
gram memoryby writingthe appropriate code inthe
Data Window Register (DWR).
7
0
-
-
DWR5 DWR4 DWR3 DWR2 DWR1 DWR0
Bits 6, 7 = Not used.
Bit 5-0 = DWR5-DWR0: Data read-only memory
Window Register Bits. These are the Data read-
only memory Window bits that correspond to the
upper bits of the data read-only memory space.
The DWR can be addressed like any RAM location
in the Data Space, it is however a write-only regis-
ter and therefore cannot be accessed using single-
bit operations. This register is used to position the
64-byte read-only data window (from address 40h
to address 7Fh of the Data space) in program
memory in 64-byte steps. The effective address of
the byte to be read as data in program memory is
obtained by concatenating the 6 least significant
bits of the register address given in the instruction
(as least significant bits) and the content of the
DWR register (as most significant bits), as illustrat-
ed in Figure 5 below. For instance, when address-
ing location 0040h of the Data Space, with 0 load-
ed in the DWR register, the physical location ad-
dressed in program memory is 00h. The DWR reg-
ister is not cleared on reset, therefore it must be
written to prior to the first access to the Data read-
only memory window area.
Caution: This register is undefined on reset. Nei-
ther read nor single bit instructions may be used to
address this register.
Note: Care is required when handling the DWR
register as it is write only. For this reason, the
DWR contents should not be changed while exe-
cuting an interrupt service routine, as the service
routine cannot save and then restore the register’s
previous contents. If it is impossible to avoid writ-
ing to the DWR during the interrupt service routine,
an image of the register must be saved in a RAM
location, and each time the program writes to the
DWR, it must also write to the image register. The
image register must be written first so that, if an in-
terrupt occurs between the two instructions, the
DWR is not affected.
Figure 5. Data read-only memory Window Memory Addressing
13 12 11 10
9
3
8
2
7
1
6
0
5
5
4
4
3
3
2
2
1
1
0 PROGRAM SPACE ADDRESS
READ
DATA ROM
WINDOW REGISTER
CONTENTS
7
6
5
4
0
DATA SPACE ADDRESS
:
(DWR)
40h-7Fh
0
1
IN INSTRUCTION
Example:
1
0
0
1
1
0
0
0
0
0
1
DWR=28h
DATA SPACE ADDRESS
:
1
1
1
1
1
0
0
0
0
0
0
59h
ROM
ADDRESS:A19h
1
0
0
1
VR01573C
10/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
1.3.6 Data RAM/EEPROM Bank Register
(DRBR)
tion. The DRBR register is not modified when an
interrupt or a subroutine occurs.
Notes :
Address: E8h — Write only
Care is required when handling the DRBR register
as it is write only. For this reason, it is not allowed
to change the DRBR contents while executing in-
terrupt service routine, as the service routine can-
not save and then restore its previous content. If it
is impossible to avoid the writing of this register in
interrupt service routine, an image of this register
must be saved in a RAM location, and each time
the program writes to DRBR it must write also to
the image register. The image register must be
written first, so if an interrupt occurs between the
two instructions the DRBR is not affected.
7
-
0
DRBR
4
DRBR
0
-
-
-
-
-
Bit 7-5 = These bits are not used
Bit 4 - DRBR4. This bit, when set, selects RAM
Page 2.
Bit 3-1. Not used
Bit 0. DRBR0. This bit, when set, selects EEP-
ROM page 0.
In DRBR Register, only 1 bit must be set. Other-
wise two or more pages are enabled in parallel,
producing errors.
The selection of the bank is made by programming
the Data RAM Bank Switch register (DRBR regis-
ter) located at address E8h of the Data Space ac-
cording to Table 1. No more than one bank should
be set at a time.
Care must also be taken not to change the
E
PROM page (when available) when the parallel
writing mode is set for the
EECTL register.
E PROM, as defined in
The DRBR register can be addressed like a RAM
Data Space at the address E8h; nevertheless it is
a write only register that cannot be accessed with
single-bit operations. This register is used to select
the desired 64-byte RAM bank of the Data Space.
The bank number has to be loaded in the DRBR
register and the instruction has to point to the se-
lected location as if it was in bank 0 (from 00h ad-
dress to 3Fh address).
Table 3. Data RAM Bank Register Set-up
DRBR
00
ST62T52C
None
ST62T62C
None
01
Not available
Not Available
Not available
RAM Page 2
Reserved
EEPROM page 0
Not Available
Not available
RAM Page 2
Reserved
02
08
This register is not cleared during the MCU initiali-
zation, therefore it must be written before the first
access to the Data Space bank region. Refer to
the Data Space description for additional informa-
10h
other
11/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
1.3.7 EEPROM Description
(PMODE). In BMODE, one byte is accessed at a
time, while in PMODE up to 8 bytes in the same
row are programmed simultaneously (with conse-
quent speed and power consumption advantages,
the latter being particularly important in battery
powered circuits).
EEPROM memory is located in 64-byte pages in
data space. This memory may be used by the user
program for non-volatile data storage.
Data space from 00h to 3Fh is paged as described
in Table 4 . EEPROM locations are accessed di-
rectly by addressing these paged sections of data
space.
General Notes:
Data should be written directly to the intended ad-
dress in EEPROM space. There is no buffer mem-
ory between data RAM and the EEPROM space.
The EEPROM does not require dedicated instruc-
tions forreador writeaccess. Onceselected viathe
Data RAM Bank Register, the active EEPROM
page is controlled by the EEPROM Control Regis-
ter (EECTL), which is described below.
When the EEPROM is busy (E2BUSY = “1”)
EECTL cannot be accessed in write mode, it is
only possible to read the status of E2BUSY. This
implies that as long as the EEPROM is busy, it is
not possible to change the status of the EEPROM
Control Register. EECTL bits 4 and 5 are reserved
and must never be set.
Bit E20FF ofthe EECTLregister must be reset prior
to any write or read access to the EEPROM. If no
bank has beenselected, or if E2OFF is set, any ac-
cess is meaningless.
Care is required when dealing with the EECTL reg-
ister, as some bits are write only. For this reason,
the EECTL contents must not be altered while ex-
ecuting an interrupt service routine.
Programming must be enabled by setting the
E2ENA bit of the EECTL register.
The E2BUSY bit of the EECTL register is set when
the EEPROM is performing a programming cycle.
Any access to the EEPROM when E2BUSY is set
is meaningless.
If it is impossible to avoid writing to this register
within an interrupt service routine, an image of the
register must be saved in a RAM location, and
each time the program writes to EECTL it must
also write to the image register. The image register
must be written to first so that, if an interrupt oc-
curs between the two instructions, the EECTL will
not be affected.
Provided E2OFF and E2BUSY are reset, an EEP-
ROM location is read just like any other data loca-
tion, also in terms of access time.
Writing to the EEPROM may be carried out in two
modes: Byte Mode (BMODE) and Parallel Mode
Table 4. Row Arrangement for Parallel Writing of EEPROM Locations
Dataspace
addresses.
Banks 0 and 1.
Byte
0
1
2
3
4
5
6
7
ROW7
ROW6
ROW5
ROW4
ROW3
ROW2
ROW1
ROW0
38h-3Fh
30h-37h
28h-2Fh
20h-27h
18h-1Fh
10h-17h
08h-0Fh
00h-07h
Up to 8 bytes in each row may be programmed simultaneously in Parallel Write mode.
The number of available 64-byte banks (1 or 2) is device dependent.
Note: The EEPROM is disabled as soon as STOP instruction is executed in order to achieve the lowest
power-consumption.
12/78
ST62T52C ST62T62C/E62C
MEMORY MAP (Cont’d)
Additional Notes on Parallel Mode:
EEPROM Control Register (EECTL)
Address: EAh Read/Write
If the user wishes to perform parallel program-
ming, the first step should be to set the E2PAR2
bit. From this time on, the EEPROM will be ad-
dressed in write mode, the ROW address and the
data will be latched and it will be possible to
change them only at the end of the programming
cycle or by resetting E2PAR2 without program-
ming the EEPROM. After the ROW address is
latched, the MCU can only “see” the selected
EEPROM row and any attempt to write or read
other rows will produce errors.
—
Reset status: 00h
7
0
E2O
FF
E2PA E2PA E2BU E2E
R1 R2 SY NA
D7
D5
D4
Bit 7 = D7: Unused.
Bit 6= E2OFF: Stand-by EnableBit.WRITE ONLY.
If thisbit is setthe EEPROMisdisabled (anyaccess
will be meaningless) andthe power consumption of
the EEPROM is reduced to its lowest value.
The EEPROM should not be read while E2PAR2
is set.
Bit 5-4 = D5-D4: Reserved. MUST be kept reset.
As soon as the E2PAR2 bit is set, the 8 volatile
ROW latches are cleared. From this moment on,
the user can load data in all or in part of the ROW.
Setting E2PAR1 will modify the EEPROM regis-
ters corresponding to the ROW latches accessed
after E2PAR2. For example, if the software sets
E2PAR2 and accesses the EEPROM by writing to
addresses 18h, 1Ah and 1Bh, and then sets
E2PAR1, these three registers will be modified si-
multaneously; the remaining bytes in the row will
be unaffected.
Bit 3 = E2PAR1: Parallel Start Bit. WRITE ONLY.
Once inParallelMode,as soonas theusersoftware
sets the E2PAR1 bit, parallel writing of the 8 adja-
cent registers will start. This bit is internally reset at
the end of the programming procedure. Note that
less than 8 bytes can be written if required, the un-
defined bytes being unaffected by the parallel pro-
gramming cycle; thisis explained ingreater detail in
the Additional Notes on Parallel Mode overleaf.
Bit 2 = E2PAR2: Parallel Mode En. Bit. WRITE
ONLY. This bit must be set by the user program in
order to perform parallel programming. If E2PAR2
is set and the parallel start bit (E2PAR1) is reset,
up to 8 adjacent bytes can be written simultane-
ously. These 8 adjacent bytes are considered as a
row, whose address lines A7, A6, A5, A4, A3 are
fixed while A2, A1 and A0 are the changing bits, as
illustrated in Table 4. E2PAR2 is automatically re-
set at the end of any parallel programming proce-
dure. It can be reset by the user software before
starting the programming procedure, thus leaving
the EEPROM registers unchanged.
Note that E2PAR2 is internally reset at the end of
the programming cycle. This implies that the user
must set the E2PAR2 bit between two parallel pro-
gramming cycles. Note that if the user tries to set
E2PAR1 while E2PAR2 is not set, there will be no
programming cycle and the E2PAR1 bit will be un-
affected. Consequently, the E2PAR1 bit cannot be
set if E2ENA is low. The E2PAR1 bit can be set by
the user, only if the E2ENA and E2PAR2 bits are
also set.
Notes: The EEPROM page shall not be changed
through the DRBR register when the E2PAR2 bit
is set.
Bit 1 = E2BUSY: EEPROM Busy Bit. READ ON-
LY. This bit is automatically set by the EEPROM
control logic when the EEPROM is in program-
ming mode. The user program should test it before
any EEPROM read or write operation; any attempt
to access the EEPROM while the busy bit is set
will be aborted and the writing procedure in
progress will be completed.
Bit 0 = E2ENA: EEPROM Enable Bit. WRITE ON-
LY. Thisbit enables programming of the EEPROM
cells. It must be set before any write to the EEP-
ROM register. Any attempt to write to the EEP-
ROM when E2ENA is low is meaningless and will
not trigger a write cycle.
13/78
ST62T52C ST62T62C/E62C
1.4 PROGRAMMING MODES
1.4.1 Option Bytes
EXTCNTL is low, STOP mode is not available with
the watchdog active.
The two Option Bytes allow configuration capabili-
ty to the MCUs. Option byte’s content is automati-
cally read, and the selected options enabled, when
the chip reset is activated.
PB2-3 PULL. When set this bit removes pull-up at
reset on PB2-PB3 pins. When cleared PB2-PB3
pins have an internal pull-up resistor at reset.
It can only be accessed during the programming
mode. This access is made either automatically
(copy from a master device) or by selecting the
OPTION BYTE PROGRAMMING mode of the pro-
grammer.
D4. Reserved. Must be cleared to 0.
WDACT. This bit controls the watchdog activation.
When it is high, hardware activation is selected.
The software activation is selected when WDACT
is low.
The option bytes are located in a non-user map.
No address has to be specified.
DELAY. This bit enables the selection of the delay
internally generated after the internal reset (exter-
nal pin, LVD, or watchdog activated) is released.
When DELAY is low, the delay is 2048 cycles of
the oscillator, it is of 32768 cycles when DELAY is
high.
EPROM Code Option Byte (LSB)
7
0
OSCIL. Oscillator selection. When this bit is low,
the oscillator must be controlled by a quartz crys-
tal, a ceramic resonator or an external frequency.
When it is high, the oscillator must be controlled by
an RC network, with only the resistor having to be
externally provided.
PRO-
TECT
EXTC- PB2-3
NTL PULL
DE-
LAY
-
WDACT
OSCIL OSGEN
EPROM Code Option Byte (MSB)
15
8
OSGEN. Oscillator Safe Guard. This bit must be
set high to enable the Oscillator Safe Guard.
When this bit is low, the OSG is disabled.
ADC
SYNCHRO
NMI
LVD
-
-
-
-
-
PULL
The Option byte is written during programming ei-
ther by using the PC menu (PC driven Mode) or
automatically (stand-alone mode).
D15-D13. Reserved. Must be cleared.
ADC SYNCHRO. When set, an A/D conversion is
started upon WAIT instruction execution, in order
to reduce supply noise. When this bit is low, an
A/D conversion is started as soon as the STA bit of
the A/D Converter Control Register is set.
1.4.2 Program Memory
EPROM/OTP programming mode is set by a
+12.5V voltage applied to the TEST/V pin. The
PP
programming flow of the ST62T62C is described
in the User Manual of the EPROM Programming
Board.
D11. Reserved, must be cleared.
D10. Reserved, must be set to one.
NMI PULL. NMI Pull-Up. This bit must be set high
to configure the NMI pin with a pull-up resistor.
When it is low, no pull-up is provided.
The MCUs can be programmed with the
ST62E6xB EPROM programming tools available
from STMicroelectronics.
LVD. LVD RESET enable.When this bit is set, safe
RESET is performed by MCU when the supply
voltage is too low. When this bit is cleared, only
power-on reset or external RESET are active.
Table 5. ST62T52C/T62C Program Memory Map
Device Address
Description
0000h-087Fh
0880h-0F9Fh
0FA0h-0FEFh
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Reserved
User ROM
Reserved
PROTECT. Readout Protection. This bit allows the
protection of the software contents against piracy.
When the bit PROTECT is set high, readout of the
OTP contents is prevented by hardware.. When
this bit is low, the user program can be read.
Interrupt Vectors
Reserved
NMI Interrupt Vector
Reset Vector
EXTCNTL. External STOP MODE control.. When
EXTCNTL is high, STOP mode is available with
watchdog active by setting NMI pin to one. When
Note: OTP/EPROM devices can be programmed
with the development tools available from STMi-
croelectronics (ST62E6X-EPB or ST626X-KIT).
14/78
ST62T52C ST62T62C/E62C
PROGRAMMING MODES (Cont’d)
1.4.3 . EEPROM Data Memory
ternal programmer. Any STMicroelectronics tool
used for the program memory (OTP/EPROM) can
also be used to program the EEPROM data mem-
ory.
EEPROM data pages are supplied in the virgin
state FFh. Partial or total programming of EEP-
ROM data memory can be performed either
through the application software or through an ex-
15/78
ST62T52C ST62T62C/E62C
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPUCoreof ST6 devicesis independent of the
I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses. In-core communication is arranged as
shown in Figure 6; the controller being externally
linked to both the Reset and Oscillator circuits,
while thecore is linked to the dedicated on-chip pe-
ripherals via the serial data bus and indirectly, for
interrupt purposes, through the control registers.
Indirect Registers (X, Y). These two indirect reg-
isters are used as pointers to memory locations in
Data space. They are used in the register-indirect
addressing mode. These registers can be ad-
dressed in the data space as RAM locations at ad-
dresses 80h (X) and 81h (Y). They can also be ac-
cessed with the direct, short direct, or bit direct ad-
dressing modes. Accordingly, the ST6 instruction
set can use the indirect registers as any other reg-
ister of the data space.
Short Direct Registers (V, W). These two regis-
ters are used to save a byte in short direct ad-
dressing mode. They can be addressed in Data
space as RAM locations at addresses 82h (V) and
83h (W). They can also be accessed using the di-
rect and bit direct addressing modes. Thus, the
ST6 instruction set can use the short direct regis-
ters as any other register of the data space.
2.2 CPU REGISTERS
The ST6Family CPUcorefeaturessixregistersand
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A). The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
tions. The accumulator can be addressed in Data
space as a RAM location at address FFh. Thus the
ST6 can manipulate the accumulator just like any
other register in Data space.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next ROM location to be processed by the core.
This ROM location may be an opcode, an oper-
and, or the address of an operand. The 12-bit
length allows the direct addressing of 4096 bytes
in Program space.
Figure 6ST6 Core Block Diagram
0,01 TO 8MHz
RESET
OSCin
OSCout
INTERRUPTS
CONTROLLER
DATA SPACE
DATA
CONTROL
SIGNALS
FLAG
VALUES
OPCODE
ADDRESS/READ LINE
ADDRESS
2
RAM/EEPROM
PROGRAM
DATA
ROM/EPROM
256
ROM/EPROM
DECODER
B-DATA
A-DATA
DEDICATIONS
ACCUMULATOR
Program Counter
and
12
FLAGS
6 LAYER STACK
ALU
RESULTS TO DATA SPACE (WRITE LINE)
VR01811
16/78
ST62T52C ST62T62C/E62C
CPU REGISTERS (Cont’d)
However, if the program space contains more than
4096 bytes, the additional memory in program
space can be addressed by using the Program
Bank Switch register.
a RETI instructions occurs. As the NMI mode is
automatically selected after the reset of the MCU,
the ST6 core uses at first the NMI flags.
Stack. The ST6 CPU includes a true LIFO hard-
ware stack which eliminates the need for a stack
pointer. The stack consists of six separate 12-bit
RAM locations that do not belong to the data
space RAM area. When a subroutine call (or inter-
rupt request) occurs, the contents of each level are
shifted into the next higher level, while the content
of the PC is shifted into the first level (the original
contents of the sixth stack level are lost). When a
subroutine or interrupt return occurs (RET or RETI
instructions), the first level register is shifted back
into the PC and the value of each level is popped
back into the previous level. Since the accumula-
tor, in common with all other data space registers,
is not stored in this stack, management of these
registers should be performed within the subrou-
tine. The stack will remain in its “deepest” position
if more than 6 nested calls or interrupts are execut-
ed, and consequently the last return address will
be lost. It will also remain in its highest position if
the stack is empty and a RET or RETI is executed.
In this case the next instruction will be executed.
The PC value is incremented after reading the ad-
dress of the current instruction. To execute relative
jumps, the PC and the offset are shifted through
the ALU, where they are added; the result is then
shifted back into the PC. The program counter can
be changed in the following ways:
- JP (Jump) instructionPC=Jump address
- CALL instructionPC= Call address
- Relative Branch Instruction.PC= PC +/- offset
- Interrupt PC=Interrupt vector
- ResetPC= Reset vector
- RET & RETI instructionsPC= Pop (stack)
- Normal instructionPC= PC + 1
Flags (C, Z). The ST6 CPU includes three pairs of
flags (Carry and Zero), each pair being associated
with one of the three normal modes of operation:
Normal mode, Interrupt mode and Non Maskable
Interrupt mode. Each pair consists of a CARRY
flag and a ZERO flag. One pair (CN, ZN) is used
during Normal operation, another pair is used dur-
ing Interrupt mode (CI, ZI), and a third pair is used
in the Non Maskable Interrupt mode (CNMI, ZN-
MI).
Figure 7ST6 CPU Programming Mode
l
b7 X REG. POINTER b0
INDEX
REGISTER
SHORT
DIRECT
ADDRESSING
MODE
b7 Y REG. POINTER b0
The ST6 CPU uses the pair of flags associated
with the current mode: as soon as an interrupt (or
a Non Maskable Interrupt) is generated, the ST6
CPU uses the Interrupt flags (resp. the NMI flags)
instead of the Normal flags. When the RETI in-
struction is executed, the previously used set of
flags is restored. It should be noted that each flag
set can only be addressed in its own context (Non
Maskable Interrupt, Normal Interrupt or Main rou-
tine). The flags are not cleared during context
switching and thus retain their status.
V REGISTER
W REGISTER
b7
b7
b0
b0
b0
b0
b7 ACCUMULATOR
PROGRAM COUNTER
b11
SIX LEVELS
STACK REGISTER
The Carry flag is set when a carry or a borrow oc-
curs during arithmetic operations; otherwise it is
cleared. The Carry flag is also set to the value of
the bit tested in a bit test instruction; it also partici-
pates in the rotate left instruction.
NORMAL FLAGS
INTERRUPTFLAGS
NMI FLAGS
C
C
C
Z
Z
Z
The Zero flag is set if the result of the last arithme-
tic or logical operation was equal to zero; other-
wise it is cleared.
Switching between the three sets of flags is per-
formed automatically when an NMI, an interrupt or
VA000423
17/78
ST62T52C ST62T62C/E62C
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES
3.1 CLOCK SYSTEM
The MCU features a Main Oscillator which can be
driven by an external clock, or used in conjunction
with an AT-cut parallel resonant crystal or a suita-
ble ceramic resonator, or with an external resistor
Figure 8. Oscillator Configurations
CRYSTAL/RESONATOR CLOCK
CRYSTAL/RESONATOR option
(R
). In addition, a Low Frequency Auxiliary Os-
NET
cillator (LFAO) can be switched in for security rea-
sons, to reduce power consumption, or to offer the
benefits of a back-up clock system.
ST6xxx
The Oscillator Safeguard (OSG) option filters
spikes from the oscillator lines, provides access to
the LFAO to provide a backup oscillator in the
event of main oscillator failure and also automati-
OSC
OSC
out
in
cally limits the internal clock frequency (f ) as a
INT
function of V , inorder to guarantee correct oper-
ation. These functions are illustrated in Figure 9.,
Figure 10., Figure 11. and Figure 12..
C
DD
C
L1n
L2
Figure 8. illustrates various possible oscillator con-
figurations using an external crystal or ceramic res-
onator, an external clock input, an external resistor
EXTERNAL CLOCK
CRYSTAL/RESONATOR option
(R
), or the lowest cost solution using only the
NET
ST6xxx
LFAO. C anC should have a capacitance inthe
L1
L2
range 12 tST6_CLK1o 22 pF for an oscillator fre-
quency in the 4-8 MHz range.
OSC
OSC
out
in
The internal MCU clock frequency (f ) is divided
INT
NC
by 12 to drive the Timer, the A/D converter and the
Watchdog timer, and by 13 to drive the CPU core,
as may be seen in Figure 11..
RC NETWORK
RC NETWORK option
With an 8MHz oscillator frequency, the fastest ma-
chine cycle is therefore 1.625µs.
A machine cycle is the smallest unit of time needed
to execute anyoperation (for instance, to increment
the Program Counter). An instruction may require
two, four, or five machine cycles for execution.
ST6xxx
OSC
NC
OSC
in
out
3.1.1 Main Oscillator
The oscillatorconfiguration maybe specified by se-
lecting the appropriate option. When the CRYS-
TAL/RESONATOR option is selected, it must be
used withaquartzcrystal, aceramicresonator oran
external signalprovided ontheOSCinpin.Whenthe
RC NETWORK optionisselected, thesystem clock
is generated by an external resistor.
R
NET
INTEGRATED CLOCK
CRYSTAL/RESONATOR option
OSG ENABLED option
The main oscillator can be turned off (when the
OSG ENABLED option is selected) by setting the
OSCOFF bit of the ADC Control Register. The
Low Frequency Auxiliary Oscillator is automatical-
ly started.
ST6xxx
OSC
OSC
NC
in
out
18/78
ST62T52C ST62T62C/E62C
CLOCK SYSTEM (Cont’d)
Turning on the main oscillator is achieved by re-
setting the OSCOFF bit of the A/D Converter Con-
trol Register or by resetting the MCU. Restarting
the main oscillator implies a delay comprising the
oscillator start up delay period plus the duration of
tions: it filters spikes from the oscillator lines which
would result in over frequency to the ST62 CPU; it
gives access to the Low Frequency Auxiliary Os-
cillator (LFAO), used to ensure minimum process-
ing in case of main oscillator failure, to offer re-
duced powerconsumption or to provide a fixed fre-
quency low cost oscillator; finally, it automatically
limits the internal clock frequency as a function of
supply voltage, in order to ensure correct opera-
tion even if the power supply should drop.
the software instruction at f
clock frequency.
LFAO
3.1.2 Low Frequency Auxiliary Oscillator
(LFAO)
The Low Frequency Auxiliary Oscillator has three
main purposes. Firstly, it can be used to reduce
power consumption in non timing critical routines.
Secondly, it offers a fully integrated system clock,
without any external components. Lastly, it acts as
a safety oscillator in case of main oscillator failure.
The OSG is enabled or disabled by choosing the
relevant OSG option. It may be viewed as a filter
whose cross-over frequency is device dependent.
Spikes on the oscillator lines result in an effectively
increased internal clock frequency. In the absence
of an OSG circuit, this may lead to an over fre-
quency for a given power supply voltage. The
OSG filters out such spikes (as illustrated in Figure
9.). In all cases, when the OSG is active, the max-
This oscillator is available when the OSG ENA-
BLED option is selected. In this case, it automati-
cally starts one of its periods after the first missing
edge from the main oscillator, whatever the reason
(main oscillator defective, no clock circuitry provid-
ed, main oscillator switched off...).
imum internal clock frequency, f , is limited to
INT
f
, which is supply voltage dependent. This re-
OSG
User code, normal interrupts, WAIT and STOP in-
structions, are processed as normal, at the re-
lationship is illustrated in Figure 12..
When the OSG is enabled, the Low Frequency
Auxiliary Oscillator may be accessed. This oscilla-
tor starts operating after the first missing edge of
the main oscillator (see Figure 10.).
duced f
frequency. The A/D converter accura-
LFAO
cy is decreased, since the internal frequency is be-
low 1MHz.
At power on, the Low Frequency Auxiliary Oscilla-
tor starts faster than the Main Oscillator. It there-
fore feeds the on-chip counter generating the POR
delay until the Main Oscillator runs.
Over-frequency, at a given power supply level, is
seen by the OSG as spikes; it therefore filters out
some cycles in order that the internal clock fre-
quency of the device is kept within the range the
The Low Frequency Auxiliary Oscillator is auto-
matically switched off as soon as the main oscilla-
tor starts.
particular device can stand (depending on V ),
DD
and below f
cy with OSG enabled.
: the maximum authorised frequen-
OSG
ADCR
Note. The OSG should be used wherever possible
as it provides maximum safety. Care must be tak-
en, however, as it can increase power consump-
tion and reduce the maximum operating frequency
Address: 0D1h — Read/Write
7
0
to f
.
OSG
ADCR ADCR ADCR ADCR ADCR OSC ADCR ADCR
OFF
7
6
5
4
3
1
0
Warning: Care has to be taken when using the
OSG, as the internal frequency is defined between
a minimum and a maximum value and is not accu-
rate.
Bit 7-3, 1-0= ADCR7-ADCR3, ADCR1-ADCR0:
ADC Control Register. These bits are not used.
Bit 2 = OSCOFF. When low, this bit enables main
oscillator to run. The main oscillator is switched off
when OSCOFF is high.
For precise timing measurements, it is not recom-
mended to use the OSG and it should not be ena-
bled in applications that use the SPI or the UART.
3.1.3 Oscillator Safe Guard
It should also be noted that power consumption in
Stop mode is higher when the OSG is enabled
(around 50µA at nominal conditions and room
temperature).
The Oscillator Safe Guard (OSG) affords drastical-
ly increased operational integrity in ST62xx devic-
es. The OSG circuit provides three basic func-
19/78
ST62T52C ST62T62C/E62C
CLOCK SYSTEM (Cont’d)
Figure 9. OSG Filtering Principle
(1)
(2)
(3)
(4)
(1) Maximum Frequency for the device to work correctly
(2)
Actual Quartz Crystal Frequency at OSCin pin
(3)
(4)
Noise from OSCin
VR001932
Resulting Internal Frequency
Figure 10. OSG Emergency Oscillator Principle
Main
Oscillator
Emergency
Oscillator
Internal
Frequency
VR001933
20/78
ST62T52C ST62T62C/E62C
CLOCK SYSTEM (Cont’d)
Figure 11. Clock Circuit Block Diagram
POR
Core
: 13
OSG
TIMER 1
M
U
X
f
MAIN
OSCILLATOR
INT
Watchdog
: 12
LFAO
: 1
Main Oscillator off
Figure 12. Maximum Operating Frequency (f
) versus Supply Voltage (V
)
MAX
DD
Maximum FREQUENCY (MHz)
8
4
7
6
5
4
3
2
1
3
2
1
f
OSG
f
Min (at 85°C)
OSG
f
Min (at 125°C)
OSG
2.5
3
3.6
4
4.5
5
5.5
6
SUPPLY VOLTAGE (V
)
DD
VR01807J
Notes:
1. In this area, operation is guaranteed at the
quartz crystal frequency.
area is guaranteed at the quartz crystal frequency.
When the OSG is enabled, access to this area is
prevented. The internal frequency is kept a f
OSG.
2. When the OSG is disabled, operation in this
area is guaranteed at the crystal frequency. When
the OSG is enabled, operation in this area is guar-
4. When the OSG is disabled, operation in this
area is not guaranteed
anteed at a frequency of at least f
When the OSG is enabled, access to this area is
OSG Min.
prevented. The internal frequency is kept at f
OSG.
3. When the OSG is disabled, operation in this
21/78
ST62T52C ST62T62C/E62C
3.2 RESETS
The MCU can be reset in four ways:
– by the external Reset input being pulled low;
– by Power-on Reset;
is executed immediately following the internal de-
lay.
To ensure correct start-up, the user should take
care that the VDD Supply is stabilized at a suffi-
cient level for the chosen frequency (see recom-
mended operation) before the reset signal is re-
leased. In addition, supply rising must start from
0V.
– by the digital Watchdog peripheral timing out.
– by Low Voltage Detection (LVD)
3.2.1 RESET Input
The RESET pin may be connected to a device of
the application board in order to reset the MCU if
required. The RESET pin may be pulled low in
RUN, WAIT or STOP mode. This input can be
used to reset the MCU internal state and ensure a
correct start-up procedure. The pin is active low
and features a Schmitt trigger input. The internal
Reset signal is generated by adding a delay to the
external signal. Therefore even short pulses on
As a consequence, the POR does not allow to su-
pervise static, slowly rising, or falling, or noisy
(presenting oscillation) VDD supplies.
An external RC network connected to the RESET
pin, or the LVD reset can be used instead to get
the best performances.
Figure 13. Reset and Interrupt Processing
the RESET pin are acceptable, provided V has
DD
completed its rising phase and that the oscillator is
running correctly (normal RUN or WAIT modes).
The MCU is kept in the Reset state as long as the
RESET pin is held low.
RESET
NMI MASK SET
INT LATCH CLEARED
( IF PRESENT )
If RESET activation occurs in the RUN or WAIT
modes, processing of the user program is stopped
(RUN modeonly), the Inputs and Outputs are con-
figured as inputs with pull-up resistors and the
main Oscillator is restarted. When the level on the
RESET pin then goes high, the initialization se-
quence is executed following expiry of the internal
delay period.
SELECT
NMI MODE FLAGS
If RESET pin activation occurs in the STOP mode,
the oscillator starts up and all Inputs and Outputs
are configured as inputs with pull-up resistors.
When the level of the RESET pin then goes high,
the initialization sequence is executed following
expiry of the internal delay period.
PUT FFEH
ON ADDRESS BUS
YES
IS RESET STILL
3.2.2 Power-on Reset
PRESENT?
The function of the POR circuit consists in waking
up the MCU by detecting around 2V a dynamic
(rising edge) variation of the VDD Supply. At the
beginning of this sequence, the MCU is configured
in the Reset state: all I/O ports are configured as
inputs with pull-up resistors and no instruction is
executed. When the power supply voltage rises to
a sufficient level, the oscillator starts to operate,
whereupon an internal delay is initiated, in order to
allow the oscillator to fully stabilize before execut-
ing the first instruction. The initialization sequence
NO
LOAD PC
FROM RESET LOCATIONS
FFE/FFF
FETCH INSTRUCTION
VA000427
22/78
ST62T52C ST62T62C/E62C
RESETS (Cont’d)
3.2.3 Watchdog Reset
ues, allowing hysteresis effect. Reference value in
case of voltage drop has been set lower than the
reference value for power-on in order to avoid any
parasitic Reset when MCU start’s running and
sinking current on the supply.
The MCU provides a Watchdog timer function in
order to ensure graceful recovery from software
upsets. If the Watchdog register is not refreshed
before an end-of-count condition is reached, the
internal reset will be activated. This, amongst oth-
er things, resets the watchdog counter.
As long as the supply voltage is below the refer-
ence value, there is a internal and static RESET
command. The MCU can start only when the sup-
ply voltage rises over the reference value. There-
fore, only two operating mode exist for the MCU:
RESET active below the voltage reference, and
running mode over the voltage reference as
shown on the Figure 14., that represents a power-
up, power-down sequence.
The MCU restarts just as though the Reset had
been generated by the RESET pin, including the
built-in stabilisation delay period.
3.2.4 LVD Reset
The on-chip Low Voltage Detector, selectable as
user option, features static Reset when supply
voltage is below a reference value. Thanks to this
feature, external reset circuit can be removed
while keeping the application safety. This SAFE
RESET is effective as well in Power-on phase as
in power supply drop with different reference val-
Note: When the RESET state is controlled by one
of the internal RESET sources (Low Voltage De-
tector, Watchdog, Power on Reset), the RESET
pin is tied to low logic level.
Figure 14. LVD Reset on Power-on and Power-down (Brown-out)
V
DD
V
Up
V
dn
RESET
RESET
time
VR02106A
3.2.5 Application Notes
No external resistor is required between V and
Direct external connection of the pin RESET to
V must be avoided in order to ensure safe be-
DD
DD
the Reset pin, thanks to the built-in pull-up device.
haviour of the internal reset sources (AND.Wired
structure).
23/78
ST62T52C ST62T62C/E62C
RESETS (Cont’d)
3.2.6 MCU Initialization Sequence
Figure 15. Reset and Interrupt Processing
When a reset occurs the stack is reset, the PC is
loaded with the address of the Reset Vector (locat-
ed in program ROM starting at address 0FFEh). A
jump to the beginning of the user program must be
coded at this address. Following a Reset, the In-
terrupt flag is automatically set, so that the CPU is
in Non Maskable Interrupt mode; this prevents the
initialisation routine from being interrupted. The in-
itialisation routine should therefore be terminated
by a RETI instruction, in order to revert to normal
mode and enable interrupts. If no pending interrupt
is presentat the end of the initialisation routine, the
MCU will continue by processing the instruction
immediately following the RETI instruction. If, how-
ever, a pending interrupt is present, it will be serv-
iced.
RESET
JP:2 BYTES/4 CYCLES
JP
RESET
VECTOR
INITIALIZATION
ROUTINE
RETI: 1 BYTE/2 CYCLES
RETI
VA00181
Figure 16. Reset Block Diagram
V
DD
ST6
INTERNAL
RESET
f
CK
OSC
COUNTER
R
PU
AND. Wired
1)
ESD
R
RESET
RESET
RESET
ON RESET
POWER
WATCHDOG RESET
LVD RESET
VR02107A
1) Resistive ESD protection. Value not guaranteed.
24/78
ST62T52C ST62T62C/E62C
RESETS (Cont’d)
Table 6. Register Reset Status
Register
EEPROM Control Register
Port Data Registers
Address(es)
0EAh
Status
Comment
EEPROM enabled (if available)
I/O are Input with pull-up
I/O are Input with pull-up
I/O are Input with pull-up
Interrupt disabled
0C0h to 0C2h
0C4h to 0C6h
0CCh to 0CEh
0C8h
Port Direction Register
Port Option Register
Interrupt Option Register
TIMER Status/Control
0D4h
00h
TIMER disabled
AR TIMER Mode Control Register
0D5h
AR TIMER stopped
AR TIMER Status/Control 1 Register 0D6h
AR TIMER Status/Control 2Register
AR TIMER Compare Register
X, Y, V, W, Register
Accumulator
0D7h
0DAh
080H TO 083H
0FFh
Data RAM
084h to 0BFh
0E8h
Data RAM Page REgister
Data ROM Window Register
EEPROM
0C9h
Undefined
00h to F3h
0D0h
As written if programmed
A/D Result Register
AR TIMER Load Register
0DBh
AR TIMER Reload/Capture Register 0D9h
TIMER Counter Register
TIMER Prescaler Register
Watchdog Counter Register
A/D Control Register
0D3h
0D2h
0D8h
0D1h
FFh
7Fh
FEh
40h
Max count loaded
A/D in Standby
25/78
ST62T52C ST62T62C/E62C
3.3 DIGITAL WATCHDOG
The digital Watchdog consists of a reloadable
downcounter timer which can be used to provide
controlled recovery from software upsets.
When the Watchdog is disabled, low power Stop
mode is available. Once activated, the Watchdog
cannot be disabled, except by resetting the MCU.
The Watchdog circuit generates a Reset when the
downcounter reaches zero. User software can
prevent this reset by reloading the counter, and
should therefore be written so that the counter is
regularly reloaded while the user program runs
correctly. In the event of a software mishap (usual-
ly caused by externally generated interference),
the user program will no longer behave in its usual
fashion and the timer register will thus not be re-
loaded periodically. Consequently the timer will
decrement down to 00h and reset the MCU. In or-
der to maximise the effectiveness of the Watchdog
function, user software must be written with this
concept in mind.
In the HARDWARE option, the Watchdog is per-
manently enabled. Since the oscillatorwill run con-
tinuously, low power mode is not available. The
STOP instruction is interpreted as a WAIT instruc-
tion, and the Watchdog continues to countdown.
However, when the EXTERNAL STOP MODE
CONTROL option has been selected low power
consumption may be achieved in Stop Mode.
Execution of the STOP instruction is then gov-
erned by a secondary function associated with the
NMI pin. If a STOP instruction is encountered
when the NMI pin is low, it is interpreted as WAIT,
as described above. If, however, the STOP in-
struction is encountered when the NMI pin is high,
the Watchdog counter is frozen and the CPU en-
ters STOP mode.
Watchdog behaviour is governed by two options,
known as “WATCHDOG ACTIVATION” (i.e.
HARDWARE or SOFTWARE) and “EXTERNAL
STOP MODE CONTROL” (see Table 7 ).
When the MCU exits STOP mode (i.e. when an in-
terrupt is generated), the Watchdog resumes its
activity.
In the SOFTWARE option, the Watchdog is disa-
bled until bit C of the DWDR register has been set.
Table 7. Recommended Option Choices
Functions Required
Stop Mode & Watchdog
Stop Mode
Recommended Options
“EXTERNAL STOP MODE” & “HARDWARE WATCHDOG”
“SOFTWARE WATCHDOG”
Watchdog
“HARDWARE WATCHDOG”
26/78
ST62T52C ST62T62C/E62C
DIGITAL WATCHDOG (Cont’d)
The Watchdog is associated with a Data space
register (Digital WatchDog Register, DWDR, loca-
tion 0D8h) which is described in greater detail in
Section 3.3.1 Digital Watchdog Register (DWDR).
This register is set to 0FEh on Reset: bit C is
cleared to “0”, which disables the Watchdog; the
timer downcounter bits, T0 to T5, and the SR bit
are all set to “1”, thus selecting the longest Watch-
dog timer period. This time period can be set to the
user’s requirements by setting the appropriate val-
ue for bits T0 to T5 in the DWDR register. The SR
bit must be set to “1”, since it is this bit which gen-
erates the Reset signal when it changes to “0”;
clearing this bit would generate an immediate Re-
set.
Figure 17. Watchdog Counter Control
D0
D1
D2
D3
D4
D5
D6
D7
C
SR
T5
T4
T3
T2
T1
T0
RESET
It should be noted that the order of the bits in the
DWDR register is inverted with respect to the as-
sociated bits in the down counter: bit 7 of the
DWDR register corresponds, in fact, to T0 and bit
2 to T5. The user should bear in mind the fact that
these bits are inverted and shifted with respect to
the physical counter bits when writing to this regis-
ter. The relationship between the DWDR register
bits and the physical implementation of the Watch-
dog timer downcounter is illustrated in Figure 17..
Only the 6 most significant bits may be used to de-
fine the time period, since it is bit 6 which triggers
the Reset when it changes to “0”. This offers the
user a choice of 64 timed periods ranging from
3,072 to 196,608 clock cycles (with an oscillator
frequency of 8MHz, this is equivalent to timer peri-
ods ranging from 384µs to 24.576ms).
8
÷2
OSC ÷12
VR02068A
27/78
ST62T52C ST62T62C/E62C
DIGITAL WATCHDOG (Cont’d)
3.3.1 Digital Watchdog Register (DWDR)
Address: 0D8h — Read/Write
Reset status: 1111 1110b
3.3.2 Application Notes
The Watchdog plays an important supporting role
in the high noise immunity of ST62xx devices, and
should be used wherever possible. Watchdog re-
lated options should be selected on the basis of a
trade-off between application security and STOP
mode availability.
7
0
T0
T1
T2
T3
T4
T5
SR
C
When STOP mode is not required, hardware acti-
vation without EXTERNAL STOP MODE CON-
TROL should be preferred, as it provides maxi-
mum security, especially during power-on.
Bit 0 = C: Watchdog Control bit
If the hardware option is selected, this bit is forced
high and the user cannot change it (the Watchdog
is always active). When the software option is se-
lected, the Watchdog function is activated by set-
ting bit C to 1, and cannot then be disabled (save
by resetting the MCU).
When STOP mode is required, hardware activa-
tion and EXTERNAL STOP MODE CONTROL
should be chosen. NMI should be high by default,
to allow STOP mode to be entered when the MCU
is idle.
When C is kept low the counter can be used as a
7-bit timer.
The NMI pin can be connected to an I/O line (see
Figure 18.) to allow its state to be controlled by
software. The I/O line can then be used to keep
NMI low while Watchdog protection is required, or
to avoid noise or key bounce. When no more
processing is required, the I/O line is released and
the device placed in STOP mode for lowest power
consumption.
This bit is cleared to “0” on Reset.
Bit 1 = SR: Software Reset bit
This bit triggers a Reset when cleared.
When C = “0” (Watchdog disabled) it is the MSB of
the 7-bit timer.
This bit is set to “1” on Reset.
When software activation is selected and the
Watchdog is not activated, the downcounter may
be used as a simple 7-bit timer (remember that the
bits are in reverse order).
Bits 2-7 = T5-T0: Downcounter bits
It should be noted that the register bits are re-
versed and shifted with respect to the physical
counter: bit-7 (T0) is the LSB of the Watchdog
downcounter and bit-2 (T5) is the MSB.
The software activation option should be chosen
only when the Watchdog counter is to be used as
a timer. To ensure the Watchdog has not been un-
expectedly activated, the following instructions
should be executed within the first 27 instructions:
These bits are set to “1” on Reset.
jrr 0, WD, #+3
ldi WD, 0FDH
28/78
ST62T52C ST62T62C/E62C
DIGITAL WATCHDOG (Cont’d)
These instructions test the C bit and Reset the
MCU (i.e. disable the Watchdog) if the bit is set
(i.e. if the Watchdog is active), thus disabling the
Watchdog.
Figure 18. A typical circuit making use of the
EXERNAL STOP MODE CONTROL feature
In all modes, a minimum of 28 instructions are ex-
ecuted after activation, before the Watchdog can
generate a Reset. Consequently, user software
should load the watchdog counter within the first
27 instructions following Watchdog activation
(software mode), or within the first 27 instructions
executed following a Reset (hardware activation).
SWITCH
NMI
I/O
It should be noted that when the GEN bit is low (in-
terrupts disabled), the NMI interrupt is active but
cannot cause a wake up from STOP/WAIT modes.
VR02002
Figure 19. Digital Watchdog Block Diagram
RESET
Q
RSFF
7
8
-2
-2
-12
R
DB1.7 LOAD SET
SET
S
OSCILLATOR
CLOCK
8
DB0
WRITE
RESET
DATA BUS
VA00010
29/78
ST62T52C ST62T62C/E62C
3.4 INTERRUPTS
The CPU can manage four Maskable Interrupt
sources, in addition to a Non Maskable Interrupt
source (top priority interrupt). Each source is asso-
ciated with a specific Interrupt Vector which con-
tains a Jump instruction to the associated interrupt
service routine. These vectors are located in Pro-
gram space (see Table 8 ).
ically reset by the core at the beginning of the non-
maskable interrupt service routine.
Interrupt request from source #1 can be config-
ured either as edge or level sensitive by setting ac-
cordingly the LES bit of the Interrupt Option Regis-
ter (IOR).
Interrupt request from source #2 are always edge
sensitive. The edge polarity can be configured by
setting accordingly the ESB bit of the Interrupt Op-
tion Register (IOR).
When an interrupt source generates an interrupt
request, and interrupt processing is enabled, the
PC register is loaded with the address of the inter-
rupt vector (i.e. of the Jump instruction), which
then causes a Jump to the relevant interrupt serv-
ice routine, thus servicing the interrupt.
Interrupt request from sources #3 & #4 are level
sensitive.
In edge sensitive mode, a latch is set when a edge
occurs on the interrupt source line and is cleared
when the associated interrupt routine is started.
So, the occurrence of an interrupt can be stored,
until completion of the running interrupt routine be-
fore being processed. If several interrupt requests
occurs before completion of the running interrupt
routine, only the first request is stored.
Interrupt sources are linked to events either on ex-
ternal pins, or on chip peripherals. Several events
can be ORed on the same interrupt source, and
relevant flags are available to determine which
event triggered the interrupt.
The Non Maskable Interrupt request has the high-
est priority and can interrupt any interrupt routine
at any time; the other four interrupts cannot inter-
rupt each other. If more than one interrupt request
is pending, these are processed by the processor
core according to their priority level: source #1 has
the higher priority while source #4 the lower. The
priority of each interrupt source is fixed.
Storage of interrupt requests is not available in lev-
el sensitive mode. To be taken into account, the
low level must be present on the interrupt pin when
the MCU samples the line after instruction execu-
tion.
At the end of every instruction, the MCU tests the
interrupt lines: if there is an interrupt request the
next instruction is not executed and the appropri-
ate interrupt service routine is executed instead.
Table 8. Interrupt Vector Map
Interrupt Source
Interrupt source #0
Interrupt source #1
Interrupt source #2
Interrupt source #3
Interrupt source #4
Priority
Vector Address
(FFCh-FFDh)
(FF6h-FF7h)
(FF4h-FF5h)
(FF2h-FF3h)
(FF0h-FF1h)
1
2
3
4
5
Table 9. Interrupt Option Register Description
SET
Enable all interrupts
Disable all interrupts
GEN
CLEARED
Rising edge mode on inter-
rupt source #2
SET
ESB
3.4.1 Interrupt request
Falling edge mode on inter-
rupt source #2
CLEARED
SET
All interrupt sources but the Non Maskable Inter-
rupt source can be disabled by setting accordingly
the GEN bit of the Interrupt Option Register (IOR).
This GEN bit also defines if an interrupt source, in-
cluding theNon Maskable Interrupt source, can re-
start the MCU from STOP/WAIT modes.
Level-sensitive mode on in-
terrupt source #1
LES
Falling edge mode on inter-
rupt source #1
CLEARED
OTHERS
NOT USED
Interrupt request from the Non Maskable Interrupt
source #0 is latched by aflip flop which is automat-
30/78
ST62T52C ST62T62C/E62C
INTERRUPTS (Cont’d)
3.4.2 Interrupt Procedure
MCU
– Automatically the MCU switches back to the nor-
mal flag set (or the interrupt flag set) and pops
the previous PC value from the stack.
The interrupt procedure is very similar to a call pro-
cedure, indeed the user can consider the interrupt
as an asynchronous call procedure. As this is an
asynchronous event, the user cannot know the
context and the time at which it occurred. As a re-
sult, the user should save all Data space registers
which may be used within the interrupt routines.
There are separate sets of processor flags for nor-
mal, interrupt and non-maskable interrupt modes,
which are automatically switched and so do not
need to be saved.
The interrupt routine usually begins by the identify-
ing the device which generated the interrupt re-
quest (by polling). The user should save the regis-
ters which are used within the interrupt routine in a
software stack. After the RETI instruction is exe-
cuted, the MCU returns to the main routine.
Figure 20. Interrupt Processing Flow Chart
The following list summarizes the interrupt proce-
dure:
INSTRUCTION
MCU
FETCH
– The interrupt is detected.
INSTRUCTION
– The C and Z flags are replaced by the interrupt
flags (or by the NMI flags).
EXECUTE
– The PC contents are stored in the first level of
the stack.
INSTRUCTION
– The normal interrupt lines are inhibited (NMI still
active).
– The first internal latch is cleared.
LOAD PC FROM
NO
INTERRUPT VECTOR
WAS
(FFC/FFD)
THE INSTRUCTION
A RETI ?
– TheassociatedinterruptvectorisloadedinthePC.
YES
?
SET
IS THE CORE
ALREADY IN
WARNING: In some circumstances, when a
maskable interrupt occurs while the ST6 core is in
NORMAL mode and especially during the execu-
tion of an ”ldi IOR, 00h” instruction (disabling all
maskable interrupts): if the interrupt arrives during
the first 3 cycles of the ”ldi” instruction (which is a
4-cycle instruction) the core will switch to interrupt
mode BUT the flags CN and ZN will NOT switch to
the interrupt pair CI and ZI.
YES
INTERRUPT MASK
NORMAL MODE?
NO
CLEAR
INTERRUPT MASK
PUSH THE
PC INTO THE STACK
SELECT
PROGRAM FLAGS
SELECT
INTERNAL MODE FLAG
User
”POP”
– User selected registers are saved within the in-
terrupt service routine (normally on a software
stack).
THE STACKED PC
CHECK IF THERE IS
AN INTERRUPT REQUEST
AND INTERRUPT MASK
NO
– Thesource of the interrupt is found by polling the
interrupt flags (if more than one source is associ-
ated with the same vector).
?
YES
VA000014
– The interrupt is serviced.
– Return from interrupt (RETI)
31/78
ST62T52C ST62T62C/E62C
INTERRUPTS (Cont’d)
3.4.3 Interrupt Option Register (IOR)
Bit 5 = ESB: Edge Selection bit.
The Interrupt Option Register (IOR) is used to en-
able/disable the individual interrupt sources and to
select the operating mode of the external interrupt
inputs. This register is write-only and cannot be
accessed by single-bit operations.
The bit ESB selects the polarity of the interrupt
source #2.
Bit 4 = GEN: Global Enable Interrupt. When this bit
is set to one, all interrupts are enabled. When this
bit is cleared to zero all the interrupts (excluding
NMI) are disabled.
Address: 0C8h — Write Only
Reset status: 00h
When the GEN bit is low, the NMI interrupt is ac-
tive but cannot cause a wake up from STOP/WAIT
modes.
7
-
0
-
This register is cleared on reset.
LES ESB GEN
-
-
-
3.4.4 Interrupt Sources
Interrupt
sources
available
on
the
Bit 7, Bits 3-0 = Unused.
Bit 6 = LES: Level/Edge Selection bit.
ST62E62C/T62C are summarized in the Table 10
with associated mask bit to enable/disable the in-
terrupt request.
When this bit is set to one, the interrupt source #1
is level sensitive. When cleared to zero the edge
sensitive mode for interrupt request is selected.
Table 10. Interrupt Requests and Mask Bits
Address
Interrupt
vector
Peripheral
Register
Mask bit
GEN
Masked Interrupt Source
Register
GENERAL
TIMER
A/D CONVERTER ADCR
IOR
C8h
All Interrupts, excluding NMI
TMZ: TIMER Overflow
TSCR1
D4h
D1h
ETI
EAI
Vector 4
Vector 4
EOC: End of Conversion
OVIE
CPIE
EIE
OVF: AR TIMER Overflow
CPF: Successful compare
EF: Active edge on ARTIMin
AR TIMER
ARMC
D5h
Vector 3
Port PAn
Port PBn
Port PCn
ORPA-DRPA
ORPB-DRPB
ORPC-DRPC
C0h-C4h
C1h-C5h
C2h-C6h
ORPAn-DRPAn PAn pin
ORPBn-DRPBn PBn pin
ORPCn-DRPCn PCn pin
Vector 1
Vector 1
Vector 2
32/78
ST62T52C ST62T62C/E62C
INTERRUPTS (Cont’d)
Figure 21. Interrupt Block Diagram
FROM REGISTER PORT A,B,C
SINGLE BIT ENABLE
PBE
V
DD
FF
CLK
CLR
PORT A
Q
0
PBE
PORT B
Bits
INT #1 (FF6,7)
MUX
I Start
1
1
RESTART FROM
STOP/WAIT
IOR REG. C8H, bit 6
FF
PORT C
Bits
INT #2 (FF4,5)
PBE
CLK
Q
CLR
SPIDIV Register
I
Start
2
SPINT bit
SPIE bit
IOR REG. C8H, bit 5
OVF
SPIMOD Register
OVIE
CPF
CPIE
INT #3 (FF2,3)
AR TIMER
EF
EIE
TMZ
ETI
TIMER1
ADC
INT #4 (FF0,1)
NMI (FFC,D)
V
DD
EOC
EAI
FF
CLK
Q
NMI
CLR
I
Start
0
Bit GEN (IOR Register)
VA0426K
33/78
ST62T52C ST62T62C/E62C
3.5 POWER SAVING MODES
The WAIT and STOP modes have been imple-
mented in the ST62xx family of MCUs in order to
reduce the product’s electrical consumption during
idle periods. These two power saving modes are
described in the following paragraphs.
of the processor core prior to the WAIT instruction,
but also on the kind of interrupt request which is
generated. This is described in the following para-
graphs. The processor core does not generate a
delay following the occurrence of the interrupt, be-
cause the oscillator clock is still available and no
stabilisation period is necessary.
3.5.1 WAIT Mode
The MCU goes into WAIT mode as soon as the
WAIT instruction is executed. The microcontroller
can be considered as being in a “software frozen”
state where the core stops processing the pro-
gram instructions, the RAM contents and peripher-
al registers are preserved as long as the power
supply voltage is higher than the RAM retention
voltage. In this mode the peripherals are still ac-
tive.
3.5.2 STOP Mode
If the Watchdog is disabled, STOP mode is availa-
ble. When in STOP mode, the MCU is placed in
the lowest power consumption mode. In this oper-
ating mode, the microcontroller can be considered
as being “frozen”, no instruction is executed, the
oscillator is stopped, the RAM contents and pe-
ripheral registers are preserved as long as the
power supply voltage is higher than the RAM re-
tention voltage, and the ST62xx core waits for the
occurrence of an external interrupt request or a
Reset to exit the STOP state.
WAIT mode can be used when the user wants to
reduce the MCU power consumption during idle
periods, while not losing track of time or the capa-
bility of monitoring external events. The active os-
cillator is not stopped in order to provide a clock
signal to the peripherals. Timer counting may be
enabled as well as the Timer interrupt, before en-
tering the WAIT mode: this allows the WAIT mode
to be exited when a Timer interrupt occurs. The
same applies to other peripherals which use the
clock signal.
If the STOP state is exited due to a Reset (by acti-
vating the external pin) the MCU will enter a nor-
mal reset procedure. Behaviour in response to in-
terrupts depends on the state of the processor
core prior to issuing the STOP instruction, and
also on the kind of interrupt request that is gener-
ated.
If the WAIT mode is exited due to a Reset (either
by activating the external pin or generated by the
Watchdog), theMCU enters a normal reset proce-
dure. If an interrupt is generated during WAIT
mode, the MCU’s behaviour depends on the state
This case will be described in the following para-
graphs. The processor core generates a delay af-
ter occurrence of the interrupt request, in order to
wait for complete stabilisation of the oscillator, be-
fore executing the first instruction.
34/78
ST62T52C ST62T62C/E62C
POWER SAVING MODE (Cont’d)
3.5.3 Exit from WAIT and STOP Modes
tered will be completed, starting with the
execution of the instruction which follows the
STOP or the WAIT instruction, and the MCU is
still in the interrupt mode. At the end of this rou-
tine pending interrupts willbe serviced in accord-
ance with their priority.
The following paragraphs describe how the MCU
exits from WAIT and STOP modes, when an inter-
rupt occurs (not a Reset). It should be noted that
the restart sequence depends on the original state
of the MCU (normal, interrupt or non-maskable in-
terrupt mode) prior to entering WAIT or STOP
mode, as well as on the interrupt type.
– In the event of a non-maskable interrupt, the
non-maskable interrupt service routine is proc-
essed first, then the routine in which the WAIT or
STOP mode was entered will be completed by
executing the instruction following the STOP or
WAIT instruction. The MCU remains in normal
interrupt mode.
Interrupts do not affect the oscillator selection.
3.5.3.1 Normal Mode
If the MCU was in the main routine when the WAIT
or STOP instruction was executed, exit from Stop
or Wait mode will occur as soon as an interrupt oc-
curs; the related interrupt routine is executed and,
on completion, the instruction which follows the
STOP or WAIT instruction is then executed, pro-
viding no other interrupts are pending.
Notes:
To achieve the lowest power consumption during
RUN or WAIT modes, the user program must take
care of:
– configuring unused I/Os as inputs without pull-up
(these should be externally tied to well defined
logic levels);
3.5.3.2 Non Maskable Interrupt Mode
If the STOP or WAIT instruction has been execut-
ed during execution of the non-maskable interrupt
routine, theMCU exits from the Stop or Wait mode
as soon as an interrupt occurs: the instruction
which follows the STOP or WAIT instruction is ex-
ecuted, and the MCU remains in non-maskable in-
terrupt mode, even if another interrupt has been
generated.
– placing all peripherals in their power down
modes before entering STOP mode;
When the hardware activated Watchdog is select-
ed, or when the software Watchdog is enabled, the
STOP instruction is disabled and a WAIT instruc-
tion will be executed in its place.
3.5.3.3 Normal Interrupt Mode
If all interrupt sources are disabled (GEN low), the
MCU can only be restarted by a Reset. Although
setting GEN low does not mask the NMI as an in-
terrupt, it will stop it generating a wake-up signal.
If the MCU was in interrupt mode before the STOP
or WAIT instruction was executed, it exits from
STOP or WAIT mode as soon as an interrupt oc-
curs. Nevertheless, two cases must be consid-
ered:
The WAIT and STOP instructions are not execut-
ed if an enabled interrupt request is pending.
– If the interrupt is a normal one, the interrupt rou-
tine in which the WAIT or STOP mode was en-
35/78
ST62T52C ST62T62C/E62C
4 ON-CHIP PERIPHERALS
4.1 I/O PORTS
The MCU features Input/Output lines which may
be individually programmed as any of the following
input or output configurations:
be also written by user software, in conjunction
with the related option registers, to select the dif-
ferent input mode options.
– Input without pull-up or interrupt
– Input with pull-up and interrupt
– Input with pull-up, but without interrupt
– Analog input
Single-bit operations on I/O registers are possible
but care is necessary because reading in input
mode is done from I/O pins while writing will direct-
ly affect the Port data register causing an unde-
sired change of the input configuration.
The Data Direction registers (DDRx) allow the
data direction (input or output) of each pin to be
set.
– Push-pull output
– Open drain output
The lines are organised as bytewise Ports.
The Option registers (ORx) are used to select the
different port options available both in input and in
output mode.
Each port is associated with 3 registers in Data
space. Each bit of these registers is associated
with a particular line (for instance, bits 0 of Port A
Data, Direction and Option registers are associat-
ed with the PA0 line of Port A).
All I/O registers can be read or written to just as
any other RAM location in Data space, so no extra
RAM cells are needed for port data storage and
manipulation. During MCU initialization, all I/O reg-
isters are cleared and the input mode with pull-ups
and no interrupt generation is selected for all the
pins, thus avoiding pin conflicts.
The DATA registers (DRx), are used to read the
voltage level values of the lines which have been
configured as inputs, or to write the logic value of
the signal to be output on the lines configured as
outputs. The port data registers can be read to get
the effective logic levels of the pins, but they can
Figure 22. I/O Port Block Diagram
RESET
V
DD
S
CONTROLS
IN
DATA
DIRECTION
REGISTER
V
DD
INPUT/OUTPUT
DATA
REGISTER
SHIFT
REGISTER
OPTION
REGISTER
S
OUT
TO INTERRUPT
TO ADC
VA00413
36/78
ST62T52C ST62T62C/E62C
I/O PORTS (Cont’d)
4.1.1 Operating Modes
4.1.1.2 Interrupt Options
Each pin may be individually programmed as input
or output with various configurations.
All input lines can be individually connected by
software to the interrupt system by programming
the OR and DR registers accordingly. The inter-
rupt trigger modes (falling edge, rising edge and
low level) can be configured by software as de-
scribed in the Interrupt Chapter for each port.
This is achieved by writing the relevant bit in the
Data (DR), Data Direction (DDR) and Option reg-
isters (OR). Table 11 illustrates the various port
configurations which can be selected by user soft-
ware.
4.1.1.3 Analog Input Options
4.1.1.1 Input Options
Some pins can be configured as analog inputs by
programming the OR and DR registers according-
ly. These analog inputs are connected to the on-
chip 8-bit Analog to Digital Converter. ONLY ONE
pin should be programmed as an analog input at
any time, since by selecting more than one input
simultaneously their pins will be effectively short-
ed.
Pull-up, High Impedance Option. All input lines
can be individually programmed with or without an
internal pull-up by programming the OR and DR
registers accordingly. If the pull-up option is not
selected, the input pin will be in the high-imped-
ance state.
Table 11. I/O Port Option Selection
DDR
OR
0
DR
0
Mode
Input
Option
0
0
0
0
1
1
With pull-up, no interrupt
0
1
Input
No pull-up, no interrupt
1
0
Input
With pull-up and with interrupt
1
1
Input
Analog input (when available)
0
X
X
Output
Output
Open-drain output (20mA sink when available)
Push-pull output (20mA sink when available)
1
Note: X = Don’t care
37/78
ST62T52C ST62T62C/E62C
I/O PORTS (Cont’d)
4.1.2 Safe I/O State Switching Sequence
outputs, it is advisable to keep a copy of the data
register in RAM. Single bit instructions may then
be used on the RAM copy, after which the whole
copy register can be written to the port data regis-
ter:
Switching the I/O ports from one state to another
should be done in a sequence which ensures that
no unwanted side effects can occur. The recom-
mended safe transitions are illustrated in Figure
23.. All other transitions are potentially risky and
should be avoided when changing the I/O operat-
ing mode, as it is most likely that undesirable side-
effects will be experienced, such as spurious inter-
rupt generation or two pins shorted together by the
analog multiplexer.
SET bit, datacopy
LD a, datacopy
LD DRA, a
Warning: Care must also be taken to not use in-
structions that act on a whole port register (INC,
DEC, or read operations) when all 8 bits are not
available on the device. Unavailable bits must be
masked by software (AND instruction).
Single bit instructions (SET, RES, INC and DEC)
should be used with great caution on Ports Data
registers, since these instructions make an implicit
read and write back of the entire register. In port
input mode, however, the data register reads from
the input pins directly, and not from the data regis-
ter latches. Since data register information in input
mode is used to set the characteristics of the input
pin (interrupt, pull-up, analog input), these may be
unintentionally reprogrammed depending on the
state of the input pins. As a general rule, it is better
to limit the use of single bit instructions on data
registers to when the whole (8-bit) port is in output
mode. In the case of inputs or of mixed inputs and
The WAIT and STOP instructions allow the
ST62xx to be used in situations where low power
consumption is needed. The lowest power con-
sumption is achieved by configuring I/Os in input
mode with well-defined logic levels.
The user must take care not to switch outputs with
heavy loads during the conversion of one of the
analog inputs in order to avoid any disturbance to
the conversion.
Figure 23. Diagram showing Safe I/O State Transitions
Interrupt
pull-up
Input
Analog
010*
011
001
Input
pull-up (Reset
state)
000
Input
Output
Output
100
101
111
Open Drain
Open Drain
Output
Push-pull
Output
Push-pull
110
Note *. xxx = DDR, OR, DR Bits respectively
38/78
ST62T52C ST62T62C/E62C
I/O PORTS (Cont’d)
Table 12. I/O Port Option Selections
MODE
AVAILABLE ON(1)
SCHEMATIC
Input
PA4-PA5
Reset state(
PB0, PB6-PB7
PC2-PC3
Data in
Reset state if PULL-UP
option disabled
PB2-PB3,
Interrupt
PA4-PA5
Input
PB0,,PB6-PB7
PC2-PC3
Reset state
Data in
Reset state if PULL-UP
option enabled
PB2-PB3
Interrupt
Input
PA4-PA5
with pull up
with interrupt
PB0, PB2-PB3,PB6-PB7
PC2-PC3
Data in
Interrupt
PA4-PA5
PC2-PC3
Analog Input
ADC
PA4-PA5
PC2-PC3
Open drain output
5mA
Data out
Open drain output
30mA
PB0, PB2-PB3,PB6-PB7
PA4-PA5
PC2-PC3
Push-pull output
5mA
Data out
Push-pull output
30mA
PB0, PB2-PB3,PB6-PB7
Note 1. Provided the correct configuration has been selected.
39/78
ST62T52C ST62T62C/E62C
I/O PORTS (Cont’d)
4.1.3 ARTimer alternate functions
ARTIMin/PB6 is connected to the AR Timer input.
It is configured through the port registers as any
standard pin of port B. To use ARTIMin/PB6 as AR
Timer input, it must be configured as input through
DDRB.
When bit PWMOE of register ARMC is low, pin
ARTIMout/PB7 is configured as any standard pin
of port B through the port registers. When PW-
MOE is high, ARTMout/PB7 is the PWM output, in-
dependently of the port registers configuration.
Figure 24. Peripheral Interface Configuration of AR Timer
PID
ARTIMin
ARTIMin
DR
AR TIMER
PID
OR
PWMOE
ARTIMout
1
0
ARTIMout
MUX
DR
VR01661G
40/78
ST62T52C ST62T62C/E62C
4.2 TIMER
The MCU features an on-chip Timer peripheral,
consisting of an 8-bit counter with a 7-bit program-
mable prescaler, giving a maximum count of 2 .
The prescaler input is the internal frequency (f
)
INT
divided by 12. The prescaler decrements on the
rising edge. Depending on the division factor pro-
grammed by PS2, PS1 and PS0 bits in the TSCR
(see Table 13.), the clock input of the timer/coun-
ter register is multiplexed to different sources. For
division factor 1, the clock input of the prescaler is
also that of timer/counter; for factor 2, bit 0 of the
prescaler register is connected to the clock input of
TCR. This bit changes its state at half the frequen-
cy of the prescaler input clock. For factor 4, bit 1 of
the PSC is connected to the clock input of TCR,
and so forth. The prescaler initialize bit, PSI, in the
TSCR register must be set to allow the prescaler
(and hence the counter) to start. If it is cleared, all
the prescaler bits are set and the counter is inhib-
ited from counting. The prescaler can be loaded
with any value between 0 and 7Fh, if bit PSI is set.
The prescaler tap is selected by means of the
PS2/PS1/PS0 bits in the control register.
15
Figure 25. shows the Timer Block Diagram. The
content of the 8-bit counter can be read/written in
the Timer/Counter register, TCR, which can be ad-
dressed in Data space as a RAM location at ad-
dress 0D3h. The state of the 7-bit prescaler can be
read in the PSC register at address 0D2h. The
control logic device is managed in the TSCR reg-
ister as described in the following paragraphs.
The 8-bit counter is decrement by the output (ris-
ing edge) coming from the 7-bit prescaler and can
be loaded and read under program control. When
it decrements to zero then the TMZ (Timer Zero)bit
in the TSCR is set. If the ETI (Enable Timer Inter-
rupt) bit in the TSCR is also set, an interrupt re-
quest is generated. The Timer interrupt can be
used to exit the MCU from WAIT mode.
Figure 26. illustrates the Timer’s working principle.
Figure 25. Timer Block Diagram
DATA BUS
8
8
8
6
5
4
3
2
1
0
8-BIT
COUNTER
b7 b6 b5
b4 b3 b2 b1 b0
STATUS/CONTROL
REGISTER
SELECT
1 OF 7
PSC
f
TMZ ETI D5
D4 PSI PS2 PS1 PS0
INT
12
3
INTERRUPT
LINE
VR02070A
41/78
ST62T52C ST62T62C/E62C
TIMER (Cont’d)
4.2.1 Timer Operation
zero, the TMZ bit in the TSCR register is set to
one.
The Timer prescaler is clocked by the prescaler
clock input (f
÷ 12).
4.2.3 Application Notes
INT
The user can select the desired prescaler division
ratio through the PS2, PS1, PS0 bits. When the
TCR count reaches 0, it sets the TMZ bit in the
TSCR. The TMZ bit can be tested under program
control to perform a timer function whenever it
goes high.
TMZ is set when the counter reaches zero; howev-
er, it may also be set by writing 00h in the TCR
register or by setting bit 7 of the TSCR register.
The TMZ bit must be cleared by user software
when servicing the timer interrupt to avoid unde-
sired interrupts when leaving the interrupt service
routine. After reset, the 8-bit counter register is
loaded with 0FFh, while the 7-bit prescaler is load-
ed with 07Fh, and the TSCR register is cleared.
This means that the Timer is stopped (PSI=“0”)
and the timer interrupt is disabled.
4.2.2 Timer Interrupt
When the counter register decrements to zero with
the ETI (Enable Timer Interrupt) bit set to one, an
interrupt request associated with Interrupt Vector
#4 is generated. When the counter decrements to
Figure 26. Timer Working Principle
7-BIT PRESCALER
BIT0
BIT1
BIT2
BIT3
BIT4
BIT5
BIT6
CLOCK
PS0
PS1
PS2
0
1
2
3
4
6
7
5
8-1 MULTIPLEXER
BIT7
BIT0
BIT1
BIT2
BIT3
BIT4
BIT5
BIT6
8-BIT COUNTER
VA00186
42/78
ST62T52C ST62T62C/E62C
TIMER (Cont’d)
A write to the TCR register will predominate over
the 8-bit counter decrement to 00h function, i.e. if a
write and a TCR register decrement to 00h occur
simultaneously, the write will take precedence,
and the TMZ bit is not set until the 8-bit counter
reaches 00h again. The values of the TCR and the
PSC registers can be read accurately at any time.
PSI=“0” both counter and prescaler are not run-
ning.
Bit 2, 1, 0 = PS2, PS1, PS0: Prescaler Mux. Se-
lect. These bits select the division ratio of the pres-
caler register.
Table 13. Prescaler Division Factors
PS2
0
PS1
0
PS0
0
Divided by
4.2.4 Timer Registers
1
2
Timer Status Control Register (TSCR)
Address: 0D4h — Read/Write
0
0
1
0
1
0
4
0
1
1
8
7
0
1
0
0
16
32
64
128
1
0
1
TMZ
ETI
D5
D4
PSI
PS2
PS1
PS0
1
1
0
1
1
1
Bit 7 = TMZ: Timer Zero bit
A low-to-high transition indicates that the timer
count register has decrement to zero. This bit
must be cleared by user software before starting a
new count.
Timer Counter Register (TCR)
Address: 0D3h
— Read/Write
7
0
Bit 6 = ETI: Enable Timer Interrup
D7
D6
D5
D4
D3
D2
D1
D0
When set, enables the timer interrupt request
(vector #4). If ETI=0 the timer interrupt is disabled.
If ETI=1 and TMZ=1 an interrupt request is gener-
ated.
Bit 7-0 = D7-D0: Counter Bits.
Bit 5 = D5: Reserved
Must be set to “1”.
Bit 4 = D4
Prescaler Register PSC
Address: 0D2h
— Read/Write
Do not care.
7
0
Bit 3 = PSI: Prescaler Initialize Bit
D7
D6
D5
D4
D3
D2
D1
D0
Used to initialize the prescaler and inhibit its count-
ing. When PSI=“0” the prescaler is set to 7Fh and
the counteris inhibited. When PSI=“1” the prescal-
er is enabled to count downwards. As long as
Bit 7 = D7: Always read as ”0”.
Bit 6-0 = D6-D0: Prescaler Bits.
43/78
ST62T52C ST62T62C/E62C
4.3 AUTO-RELOAD TIMER
The Auto-Reload Timer (AR Timer) on-chip pe-
ripheral consists of an 8-bit timer/counter with
compare and capture/reload capabilities and of a
7-bit prescaler with a clock multiplexer, enabling
the prescaler and counter contents are frozen.
When TEN is set, the AR counter runs at the rate
of the selected clock source. The counter is
cleared on system reset.
the clock input to be selected as f , f
or an
INT INT/3
The AR counter may also be initialized by writing
to the ARLR load register, which also causes an
immediate copy of the value to be placed in the AR
counter, regardless of whether the counter is run-
ning or not. Initialization of the counter, by either
method, will also clear the ARPSC register, where-
upon counting will start from a known value.
external clock source. A Mode Control Register,
ARMC, two Status Control Registers, ARSC0 and
ARSC1, an output pin, ARTIMout, and an input
pin, ARTIMin, allow the Auto-Reload Timer to be
used in 4 modes:
– Auto-reload (PWM generation),
– Output compare and reload on external event
(PLL),
4.3.2 Timer Operating Modes
Four different operating modes are available for
the AR Timer:
– Input capture and output compare for time meas-
urement.
Auto-reload Mode with PWM Generation. This
mode allows a Pulse Width Modulated signal to be
generated on the ARTIMout pin with minimum
Core processing overhead.
– Input capture and output compare for period
measurement.
The AR Timer can be used to wake the MCU from
WAIT mode either with an internal or with an exter-
nal clock. It also can be used to wake the MCU
from STOP mode, if used with an external clock
signal connected to the ARTIMin pin. A Load reg-
ister allows the program to read and write the
counter on the fly.
The free running 8-bit counter is fed by the pres-
caler’s output, and is incremented on every rising
edge of the clock signal.
When a counter overflow occurs, the counter is
automatically reloaded with the contents of the Re-
load/Capture Register, ARCC, and ARTIMout is
set. When the counter reaches the value con-
tained in the compare register (ARCP), ARTIMout
is reset.
4.3.1 AR Timer Description
The AR COUNTER is an 8-bit up-counter incre-
mented on the input clock’s rising edge. The coun-
ter is loaded from the ReLoad/Capture Register,
ARRC, for auto-reload or capture operations, as
well as for initialization. Direct access to the AR
counter is not possible; however, by reading or
writing the ARLR load register, it is possible to
read or write the counter’s contents on the fly.
On overflow, the OVF flag of the ARSC0 register is
set and an overflow interrupt request is generated
if the overflow interrupt enable bit, OVIE, in the
Mode Control Register (ARMC), is set. The OVF
flag must be reset by the user software.
When the counter reaches the compare value, the
CPF flag of the ARSC0 register is set and a com-
pare interrupt request is generated, if the Compare
Interrupt enable bit, CPIE, in the Mode Control
Register (ARMC), is set. The interrupt service rou-
tine may then adjust the PWM period by loading a
new value into ARCP. The CPF flag must be reset
by user software.
The AR Timer’s input clock can be either the inter-
nal clock (from the Oscillator Divider), the internal
clock divided by 3, or the clock signal connected to
the ARTIMin pin. Selection between these clock
sources is effected by suitably programming bits
CC0-CC1 of the ARSC1 register. The output of the
AR Multiplexer feeds the 7-bit programmable AR
Prescaler, ARPSC, which selects one of the 8
available taps of the prescaler, as defined by
PSC0-PSC2 in the AR Mode Control Register.
Thus the division factor of the prescaler can be set
to 2n (where n = 0, 1,..7).
The PWM signal is generated on the ARTIMout
pin (refer to the Block Diagram). The frequency of
this signal is controlled by the prescaler setting
and by the auto-reload value present in the Re-
load/Capture register, ARRC. The duty cycle of
the PWM signal is controlled by the Compare Reg-
ister, ARCP.
The clock input to the AR counter is enabled by the
TEN (Timer Enable) bit in the ARMC register.
When TEN is reset, the AR counter is stopped and
44/78
ST62T52C ST62T62C/E62C
AUTO-RELOAD TIMER (Cont’d)
Figure 27. AR Timer Block Diagram
DATA BUS
8
DDRB7
DRB7
AR COMPARE
REGISTER
8
PB7/
ARTIMout
CPF
COMPARE
8
R
S
PWMOE
OVF
OVF
f
INT
M
U
X
OVIE
8-Bit
7-Bit
f
/3
INT
AR PRESCALER
LOAD
AR COUNTER
TCLD
EIE
PS0-PS2
CC0-CC1
EF
AR TIMER
8
INTERRUPT
CPF
CPIE
8
8
PB6/
ARTIMin
SL0-SL1
AR
AR
EF
RELOAD/CAPTURE
REGISTER
LOAD
SYNCHRO
REGISTER
8
8
DATA BUS
VR01660A
45/78
ST62T52C ST62T62C/E62C
AUTO-RELOAD TIMER (Cont’d)
It should be noted that the reload values will also
affect thevalue and the resolution of the duty cycle
of PWM output signal. To obtain a signal on ARTI-
Mout, the contents of the ARCP register must be
greater than the contents of the ARRC register.
The ARTC counter is initialized by writing to the
ARRC register and by then setting the TCLD (Tim-
er Load) and the TEN (Timer Clock Enable) bits in
the Mode Control register, ARMC.
Enabling and selection of the clock source is con-
trolled by the CC0, CC1, SL0 and SL1 bits in the
Status Control Register, ARSC1. The prescaler di-
vision ratio is selected by the PS0, PS1 and PS2
bits in the ARSC1 register.
The maximum available resolution for the ARTI-
Mout duty cycle is:
Resolution = 1/[255-(ARRC)]
Where ARRC is the content of the Reload/Capture
register. The compare value loaded in the Com-
pare Register, ARCP, must be in the range from
(ARRC) to 255.
In Auto-reload Mode, any of the three available
clock sources can be selected: Internal Clock, In-
ternal Clock divided by 3 or the clock signal
present on the ARTIMin pin.
Figure 28. Auto-reload Timer PWM Function
COUNTER
255
COMPARE
VALUE
RELOAD
REGISTER
000
t
PWM OUTPUT
t
VR001852
46/78
ST62T52C ST62T62C/E62C
AUTO-RELOAD TIMER (Cont’d)
Capture Mode with PWM Generation. In this
mode, the AR counter operates as a free running
8-bit counter fed by the prescaler output. The
counter is incremented on every clock rising edge.
the count is incremented on every clock rising
edge.
Each counter overflow sets the ARTIMout pin. A
match between the counter and ARCP (Compare
Register) resets the ARTIMout pin and sets the
compare flag, CPF. A compare interrupt request is
generated if the related compare interrupt enable
bit, CPIE, is set. A PWM signal is generated on
ARTIMout. The CPF flag must be reset by user
software.
An 8-bit capture operation from the counter to the
ARRC register is performed on every active edge
on the ARTIMin pin, when enabled by Edge Con-
trol bits SL0, SL1 in the ARSC1 register. At the
same time, the External Flag, EF, in the ARSC0
register is set and an external interrupt request is
generated if the External Interrupt Enable bit, EIE,
in the ARMC register, is set. The EF flag must be
reset by user software.
Initialization of the counter is as described in the
previous paragraph. In addition, if the external AR-
TIMin input is enabled, an active edge on the input
pin willcopy the contents of the ARRC register into
the counter, whether the counter is running or not.
Each ARTC overflow sets ARTIMout, while a
match between the counter and ARCP (Compare
Register) resets ARTIMout and sets the compare
flag, CPF. A compare interrupt request is generat-
ed if the related compare interrupt enable bit,
CPIE, is set. A PWM signal is generated on ARTI-
Mout. The CPF flag must be reset by user soft-
ware.
Notes:
The allowed AR Timer clock sources are the fol-
lowing:
AR Timer Mode
Auto-reload mode
Capture mode
Clock Sources
, f , ARTIMin
f
f
f
f
INT INT/3
The frequency of the generated signal is deter-
mined by the prescaler setting. The duty cycle is
determined by the ARCP register.
, f
INT INT/3
Capture/Reset mode
External Load mode
, f
INT INT/3
, f
INT INT/3
Initialization and reading of the counter are identi-
cal to the auto-reload mode (see previous descrip-
tion).
The clock frequency should not be modified while
the counter is counting, since the counter may be
set to an unpredictable value. For instance, the
multiplexer setting should not be modified while
the counter is counting.
Enabling and selection of clock sources is control-
led by the CC0 and CC1 bits in the AR Status Con-
trol Register, ARSC1.
Loading of the counter by any means (by auto-re-
load, through ARLR, ARRC or by the Core) resets
the prescaler at the same time.
The prescaler division ratio is selected by pro-
gramming the PS0, PS1 and PS2 bits in the
ARSC1 Register.
Care should be taken when both the Capture inter-
rupt and the Overflow interrupt are used. Capture
and overflow are asynchronous. If the capture oc-
curs when the Overflow Interrupt Flag, OVF, is
high (between counter overflow and the flag being
reset by software, in the interrupt routine), the Ex-
ternal Interrupt Flag, EF, may be cleared simul-
taneusly without the interrupt being taken into ac-
count.
In Capture mode, the allowed clock sources are
the internal clock and the internal clock divided by
3; the external ARTIMin input pin should not be
used as a clock source.
Capture Mode with Reset of counter and pres-
caler, and PWM Generation. This mode is identi-
cal to the previous one, with the difference that a
capture condition also resets the counter and the
prescaler, thus allowing easy measurement of the
time between two captures (for input period meas-
urement on the ARTIMin pin).
The solution consists in resetting the OVF flag by
writing 06h in the ARSC0 register. The value of EF
is not affected by this operation. If an interrupt has
occured, it will be processed when the MCU exits
from the interrupt routine (the second interrupt is
latched).
Load on External Input. The counter operates as
a free running 8-bit counter fed by the prescaler.
47/78
ST62T52C ST62T62C/E62C
AUTO-RELOAD TIMER (Cont’d)
4.3.3 AR Timer Registers
ARSC0 register is also set, an interrupt request is
generated.
AR Mode Control Register (ARMC)
Bit 1-0 = ARMC1-ARMC0: Mode Control Bits 1-0.
These are the operating mode control bits. The fol-
lowing bit combinations will select the various op-
erating modes:
Address: D5h
— Read/Write
Reset status: 00h
7
0
ARMC1
ARMC0
Operating Mode
Auto-reload Mode
Capture Mode
TCLD
TEN PWMOE
EIE
CPIE OVIE ARMC1 ARMC0
0
0
0
1
The AR Mode Control Register ARMC is used to
program the different operating modes of the AR
Timer, to enable the clock and to initialize the
counter. It can be read and written to by the Core
and it is cleared on system reset (the AR Timer is
disabled).
Capture Mode with Reset
of ARTC and ARPSC
1
1
0
1
Load on External Edge
Mode
AR Timer Status/Control Registers ARSC0 &
ARSC1. These registers contain the AR Timer sta-
tus information bits and also allow the program-
ming of clock sources, active edge and prescaler
multiplexer setting.
Bit 7 = TLCD: Timer Load Bit. This bit, when set,
will cause the contents of ARRC register to be
loaded into the counter and the contents of the
prescaler register, ARPSC, are cleared in order to
initialize the timer before starting to count. This bit
is write-only and any attempt to read it will yield a
logical zero.
ARSC0 register bits 0,1 and 2 contain the interrupt
flags of the AR Timer. These bits are read normal-
ly. Each one may be reset by software. Writing a
one does not affect the bit value.
Bit 6 = TEN: Timer Clock Enable. This bit, when
set, allows the timer to count. When cleared, it will
stop the timer and freeze ARPSC and ARTSC.
AR Status Control Register 0 (ARSC0)
Address: D6h
— Read/Clear
Bit 5 = PWMOE: PWM Output Enable. This bit,
when set, enables the PWM output on the ARTI-
Mout pin. When reset, the PWM output is disabled.
7
0
D7
D6
D5
D4
D3
EF
CPF
OVF
Bit 4 = EIE: External Interrupt Enable. This bit,
when set, enables the external interrupt request.
When reset, the external interrupt request is
masked. If EIE is set and the related flag, EF, in
the ARSC0 register is also set, an interrupt re-
quest is generated.
Bits 7-3 = D7-D3: Unused
Bit 2 = EF: External Interrupt Flag. This bit is set by
any active edge on the external ARTIMin input pin.
The flag is cleared by writing a zero to the EF bit.
Bit 3 = CPIE: Compare Interrupt Enable. This bit,
when set, enables the compare interrupt request.
If CPIE is reset, the compare interrupt request is
masked. IfCPIE is set and the related flag, CPF, in
the ARSC0 register is also set, an interrupt re-
quest is generated.
Bit 1= CPF: Compare Interrupt Flag. This bit is set
if the contents of the counter and the ARCP regis-
ter are equal. The flag is cleared by writing a zero
to the CPF bit.
Bit 0= OVF: Overflow Interrupt Flag. This bit is set
by a transition of the counter from FFh to 00h
(overflow). The flag is cleared by writing a zero to
the OVF bit.
Bit 2 = OVIE: Overflow Interrupt. This bit, when
set, enables the overflow interrupt request. If OVIE
is reset, the compare interrupt request is masked.
If OVIE is set and the related flag, OVF in the
48/78
ST62T52C ST62T62C/E62C
AUTO-RELOAD TIMER (Cont’d)
AR Status Control Register 1(ARSC1)
AR Load Register ARLR. The ARLR load register
is used to read or write the ARTC counter register
“on the fly” (while it is counting). The ARLR regis-
ter is not affected by system reset.
Address: D7h
— Read/Write
7
0
AR Load Register (ARLR)
PS2
PS1
PS0
D4
SL1
SL0
CC1
CC0
Address: DBh
— Read/Write
Bist 7-5 = PS2-PS0: Prescaler Division Selection
Bits 2-0. These bits determine the Prescaler divi-
sion ratio. The prescaler itself is not affected by
these bits.The prescalerdivision ratiois listed inthe
following table:
7
0
D7
D6
D5
D4
D3
D2
D1
D0
Bit 7-0 = D7-D0: Load Register Data Bits. These
are the load register data bits.
Table 14. Prescaler Division Ratio Selection
PS2
0
PS1
0
PS0
0
ARPSC Division Ratio
AR Reload/Capture Register. The ARRC re-
load/capture register is used to hold the auto-re-
load value which is automatically loaded into the
counter when overflow occurs.
1
2
0
0
1
0
1
0
4
0
1
1
8
AR Reload/Capture (ARRC)
1
0
0
16
32
64
128
Address: D9h
— Read/Write
1
0
1
7
0
1
1
0
D7
D6
D5
D4
D3
D2
D1
D0
1
1
1
Bit 4 = D4: Reserved. Must be kept reset.
Bit 7-0 = D7-D0: Reload/Capture Data Bits. These
Bit 3-2= SL1-SL0: Timer InputEdge Control Bits 1-
0. These bits control theedge function of the Timer
input pinforexternal synchronization. Ifbit SL0isre-
set, edgedetectionis disabled; if setedge detection
is enabled.If bit SL1is reset, the AR Timerinput pin
is rising edge sensitive; if set, it is falling edge sen-
sitive.
are the Reload/Capture register data bits.
AR Compare Register. The CP compare register
is used to hold the compare value for the compare
function.
AR Compare Register (ARCP)
SL1
X
SL0
0
Edge Detection
Disabled
Address: DAh
— Read/Write
7
0
0
1
Rising Edge
Falling Edge
1
1
D7
D6
D5
D4
D3
D2
D1
D0
Bit 1-0 = CC1-CC0: Clock Source Select Bit 1-0.
These bits select the clock source for the AR Timer
through the AR Multiplexer. The programming of
the clocksources is explainedin the following Table
15 :
Bit 7-0 = D7-D0: Compare Data Bits. These are
the Compare register data bits.
Table 15. Clock Source Selection.
CC1
CC0
Clock Source
0
0
1
1
0
1
0
1
Fint
Fint Divided by 3
ARTIMin Input Clock
Reserved
49/78
ST62T52C ST62T62C/E62C
4.4 A/D CONVERTER (ADC)
The A/D converter peripheral is an 8-bit analog to
digital converter with analog inputs as alternate I/O
functions (the number of which is device depend-
ent), offering 8-bit resolution with a typical conver-
sion time of 70us (at an oscillator clock frequency
of 8MHz).
sion to allow stabilisation of the A/D converter.
This action is also needed before entering WAIT
mode, since the A/D comparator is not automati-
cally disabled in WAIT mode.
During Reset, any conversion in progress is
stopped, the control register is reset to 40h and the
ADC interrupt is masked (EAI=0).
The ADC converts the input voltage by a process
of successive approximations, using a clock fre-
quency derived from the oscillator with a division
factor of twelve. With an oscillator clock frequency
less than 1.2MHz, conversion accuracy is de-
creased.
Figure 29. ADC Block Diagram
INTERRUPT
CLOCK
Selection of the input pin is done by configuring
the related I/O line as an analog input via the Op-
tion and Data registers (refer to I/O ports descrip-
tion for additional information). Only one I/O line
must be configured as an analog input at any time.
The user must avoid any situation in which more
than one I/O pin is selected as an analog input si-
multaneously, to avoid device malfunction.
Ain
CONVERTER
RESET
AV
AV
DD
SS
RESULT REGISTER
8
CONTROL REGISTER
8
The ADC uses two registers in the data space: the
ADC data conversion register, ADR, which stores
the conversion result, and the ADC control regis-
ter, ADCR, used to program the ADC functions.
CORE
CORE
CONTROL SIGNALS
VA00418
A conversion is started by writing a “1” to the Start
bit (STA) in the ADC control register. This auto-
matically clears (resets to “0”) the End Of Conver-
sion Bit (EOC). When a conversion is complete,
the EOC bit is automatically set to “1”, in order to
flag that conversion is complete and that the data
in the ADC data conversion register is valid. Each
conversion has to be separately initiated by writing
to the STA bit.
4.4.1 Application Notes
The A/D converter does not feature a sample and
hold circuit. The analog voltage to be measured
should therefore be stable during the entire con-
version cycle. Voltage variation should not exceed
±1/2 LSB for the optimum conversion accuracy. A
low pass filter may be used at the analog input
pins to reduce input voltage variation during con-
version.
The STA bit is continuously scanned so that, if the
user sets it to “1” while a previous conversion is in
progress, a new conversion is started before com-
pleting the previous one. The start bit (STA) is a
write only bit, any attempt to read it will show a log-
ical “0”.
When selected as an analog channel, the input pin
is internally connected to a capacitor C of typi-
ad
cally 12pF. For maximum accuracy, this capacitor
must be fully charged at the beginning of conver-
sion. In the worst case, conversion starts one in-
struction (6.5 µs) after the channel has been se-
lected. In worst case conditions, the impedance,
ASI, of the analog voltage source is calculated us-
ing the following formula:
The A/D converter features a maskable interrupt
associated with the end of conversion. This inter-
rupt is associated with interrupt vector #4 and oc-
curs when the EOC bit is set (i.e. when a conver-
sion is completed). The interrupt is masked using
the EAI (interrupt mask) bit in the control register.
6.5µs = 9 x C x ASI
ad
(capacitor charged to over 99.9%), i.e. 30 kΩ in-
cluding a 50% guardband. ASI can be higher if C
has been charged for a longer period by adding in-
structions before the start of conversion (adding
more than 26 CPU cycles is pointless).
The power consumption of the device can be re-
duced by turning off the ADC peripheral. This is
done by setting the PDS bit in the ADC control reg-
ister to “0”. If PDS=“1”, the A/D is powered and en-
abled for conversion. This bit must be set at least
one instruction before the beginning of the conver-
ad
50/78
ST62T52C ST62T62C/E62C
A/D CONVERTER (Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
the noise during the conversion. But the first con-
version step is performed before the execution of
the WAIT when most of clocks signals are still en-
abled . The key is to synchronize the ADC start
with the effective execution of the WAIT. This is
achieved by setting ADC SYNC option. This way,
ADC conversion starts in effective WAIT for maxi-
mum accuracy.
The accuracy of the conversion depends on the
quality of the power supplies (V
and V ). The
DD
SS
user must take special care to ensure a well regu-
lated reference voltage is present on the V and
Note: With this extra option, it is mandatory to ex-
ecute WAIT instruction just after ADC start instruc-
tion. Insertion of any extra instruction may cause
spurious interrupt request at ADC interrupt vector.
DD
V
pins (power supply voltage variations must be
SS
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the V
DD
pin.
A/D Converter Control Register (ADCR)
The converter resolution is given by::
Address: 0D1h
— Read/Write
7
0
VDD VSS
----------------------------
256
EAI
EOC
STA
PDS
D3
D2
D1
D0
Bit 7= EAI: Enable A/D Interrupt. If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
The Input voltage (Ain) which is to be converted
must be constant for 1µs before conversion and
remain constant during conversion.
Bit 6 = EOC: End of conversion. Read Only. This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
Conversion resolution can be improved if the pow-
er supply voltage (V ) to the microcontroller is
DD
lowered.
In order to optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
Bit 5 = STA: Start of Conversion. Write Only. Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
instruction may cause a small variation of the V
DD
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
Bit 4 = PDS: Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
Bit 3-0 = D3-D0. Not used
A/D Converter Data Register (ADR)
Address: 0D0h
— Read only
7
0
D7
D6
D5
D4
D3
D2
D1
D0
One extra feature is available in the ADC to get a
better accuracy. In fact, each ADC conversion has
to be followed by a WAIT instruction to minimize
Bit 7-0 = D7-D0: 8 Bit A/D Conversion Result.
51/78
ST62T52C ST62T62C/E62C
5 SOFTWARE
5.1 ST6 ARCHITECTURE
The ST6 software has been designed to fully use
the hardware in the most efficient way possible
while keeping byte usage to a minimum; in short,
to provide byte efficient programming capability.
The ST6 core has the ability to set or clear any
register or RAM location bit of the Data space with
a single instruction. Furthermore, the program
may branch to a selected address depending on
the status of any bit of the Data space. The carry
bit is stored with the value of the bit when the SET
or RES instruction is processed.
bits of the opcode with the byte following the op-
code. The instructions (JP, CALL) which use the
extended addressing mode are able to branch to
any address of the 4K bytes Program space.
An extended addressing mode instruction is two-
byte long.
Program Counter Relative. The relative address-
ing mode is only used in conditional branch in-
structions. The instruction is used to perform a test
and, if the condition is true, a branch with a span of
-15 to +16 locations around the address of the rel-
ative instruction. If the condition is not true, the in-
struction which follows the relative instruction is
executed. The relative addressing mode instruc-
tion is one-byte long. The opcode is obtained in
adding the three most significant bits which char-
acterize the kind of the test, one bit which deter-
mines whether the branch is a forward (when it is
0) or backward (when it is 1) branch and the four
less significant bits which give the span of the
branch (0h to Fh) which must be added or sub-
tracted to the address of the relative instruction to
obtain the address of the branch.
5.2 ADDRESSING MODES
The ST6 core offers nine addressing modes,
which are described in the following paragraphs.
Three different address spaces are available: Pro-
gram space, Data space, and Stack space. Pro-
gram space contains the instructions which are to
be executed, plus the data for immediate mode in-
structions. Data space contains the Accumulator,
the X,Y,V and W registers, peripheral and In-
put/Output registers, the RAM locations and Data
ROM locations (for storage of tables and con-
stants). Stack space contains six 12-bit RAM cells
used to stack the return addresses for subroutines
and interrupts.
Bit Direct. In the bit direct addressing mode, the
bit to be set or cleared is part of the opcode, and
the byte following the opcode points to the ad-
dress of the byte in which the specified bit must be
set or cleared. Thus, any bit in the 256 locations of
Data space memory can be set or cleared.
Immediate. In the immediate addressing mode,
the operand of the instruction follows the opcode
location. Asthe operand is a ROM byte, the imme-
diate addressing mode is used to access con-
stants which do not change during program execu-
tion (e.g., a constant used to initialize a loop coun-
ter).
Bit Test & Branch. The bit test and branch ad-
dressing mode is a combination of direct address-
ing and relative addressing. The bit test and
branch instruction is three-byte long. The bit iden-
tification and the tested condition are included in
the opcode byte. The address of the byte to be
tested follows immediately the opcode in the Pro-
gram space. The third byte is the jump displace-
ment, which is in the range of -127 to +128. This
displacement can be determined using a label,
which is converted by the assembler.
Direct. In the direct addressing mode, the address
of the byte which is processed by the instruction is
stored in the location which follows the opcode. Di-
rect addressing allows the user to directly address
the 256 bytes in Data Space memory with a single
two-byte instruction.
Short Direct. The core can address the four RAM
registers X,Y,V,W (locations 80h, 81h, 82h, 83h) in
the short-direct addressing mode. In this case, the
instruction is only one byte and the selection of the
location to be processed is contained in the op-
code. Short direct addressing is a subset of the di-
rect addressing mode. (Note that 80h and 81h are
also indirect registers).
Indirect. In the indirect addressing mode, the byte
processed by the register-indirect instruction is at
the address pointed by the content of one of the in-
direct registers, X or Y (80h,81h). The indirect reg-
ister is selected by the bit 4 of the opcode. A regis-
ter indirect instruction is one byte long.
Inherent. In the inherent addressing mode, all the
information necessary to execute the instruction is
contained in the opcode. These instructions are
one byte long.
Extended. In the extended addressing mode, the
12-bit address needed to define the instruction is
obtained by concatenating the four less significant
52/78
ST62T52C ST62T62C/E62C
5.3 INSTRUCTION SET
The ST6 core offers a set of 40 basic instructions
which, when combined with nine addressing
modes, yield 244 usable opcodes. They can be di-
vided into six different types: load/store, arithme-
tic/logic, conditional branch, control instructions,
jump/call, and bit manipulation. The following par-
agraphs describe the different types.
Load & Store. These instructions use one, two or
three bytes in relation with the addressing mode.
One operand is the Accumulator for LOAD and the
other operand is obtained from data memory using
one of the addressing modes.
For Load Immediate one operand can be any of
the 256 data space bytes while the other is always
immediate data.
All the instructions belonging to a given type are
presented in individual tables.
Table 16. Load & Store Instructions
Flags
Instruction
LD A, X
Addressing Mode
Short Direct
Bytes
Cycles
Z
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
C
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
LD A, Y
LD A, V
LD A, W
LD X, A
LD Y, A
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Direct
LD V,A
LD W, A
LD A, rr
LD rr, A
Direct
LD A, (X)
LD A, (Y)
LD (X), A
LD (Y), A
LDI A, #N
LDI rr, #N
Indirect
Indirect
Indirect
Indirect
Immediate
Immediate
Notes:
X,Y. Indirect Register Pointers, V & W Short Direct Registers
# . Immediate data (stored in ROM memory)
rr. Data space register
∆. Affected
* . Not Affected
53/78
ST62T52C ST62T62C/E62C
INSTRUCTION SET (Cont’d)
Arithmetic and Logic. These instructions are
used to perform the arithmetic calculations and
logic operations. In AND, ADD, CP, SUB instruc-
tions one operand is always the accumulator while
the other can be either a data space memory con-
tent or an immediate value in relation with the ad-
dressing mode. In CLR, DEC, INC instructions the
operand can be any of the 256 data space ad-
dresses. In COM, RLC, SLA the operand is always
the accumulator.
Table 17. Arithmetic & Logic Instructions
Flags
Instruction
ADD A, (X)
Addressing Mode
Indirect
Bytes
Cycles
Z
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
C
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
1
1
2
2
1
1
2
2
2
3
1
1
1
2
2
1
1
1
1
2
2
1
1
1
1
1
1
2
2
1
1
1
2
1
1
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
ADD A, (Y)
ADD A, rr
ADDI A, #N
AND A, (X)
AND A, (Y)
AND A, rr
ANDI A, #N
CLR A
Indirect
Direct
Immediate
Indirect
Indirect
Direct
Immediate
Short Direct
Direct
CLR r
COM A
Inherent
Indirect
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
CP A, (X)
CP A, (Y)
CP A, rr
CPI A, #N
DEC X
Indirect
Direct
Immediate
Short Direct
Short Direct
Short Direct
Short Direct
Direct
DEC Y
*
DEC V
*
DEC W
*
DEC A
*
DEC rr
Direct
*
DEC (X)
DEC (Y)
INC X
Indirect
*
Indirect
*
Short Direct
Short Direct
Short Direct
Short Direct
Direct
*
INC Y
*
INC V
*
INC W
*
INC A
*
INC rr
Direct
*
INC (X)
Indirect
*
INC (Y)
Indirect
*
RLC A
Inherent
Inherent
Indirect
∆
∆
∆
∆
∆
∆
SLA A
SUB A, (X)
SUB A, (Y)
SUB A, rr
SUBI A, #N
Indirect
Direct
Immediate
Notes:
X,Y.Indirect Register Pointers, V & W Short Direct RegistersD. Affected
# . Immediate data (stored in ROM memory)* . Not Affected
rr. Data space register
54/78
ST62T52C ST62T62C/E62C
INSTRUCTION SET (Cont’d)
Conditional Branch. The branch instructions
achieve a branch in the program when the select-
ed condition is met.
Control Instructions. The control instructions
control the MCU operations during program exe-
cution.
Bit Manipulation Instructions. These instruc-
tions can handle any bit in data space memory.
One group either sets or clears. The other group
(see Conditional Branch) performs the bit test
branch operations.
Jump and Call. These two instructions are used
to perform long (12-bit) jumps or subroutines call
inside the whole program space.
Table 18. Conditional Branch Instructions
Flags
Instruction
Branch If
Bytes
Cycles
Z
*
*
*
*
*
*
C
*
JRC e
C = 1
1
1
1
1
3
3
2
2
2
2
5
5
JRNC e
C = 0
Z = 1
*
JRZ e
*
JRNZ e
Z = 0
*
JRR b, rr, ee
JRS b, rr, ee
Bit = 0
Bit = 1
∆
∆
Notes:
b.
e.
3-bit address
rr. Data space register
∆ . Affected. The tested bit is shifted into carry.
5 bit signed displacement in the range -15 to +16<F128M>
ee. 8 bit signed displacement in the range -126 to +129
* . Not Affected
Table 19. Bit Manipulation Instructions
Flags
Instruction
Addressing Mode
Bytes
Cycles
Z
C
*
SET b,rr
Bit Direct
Bit Direct
2
2
4
4
*
*
RES b,rr
*
Notes:
b.
3-bit address;
* . Not<M> Affected
rr. Data space register;
Table 20. Control Instructions
Flags
Instruction
Addressing Mode
Bytes
Cycles
Z
*
C
*
NOP
Inherent
Inherent
Inherent
Inherent
Inherent
1
1
1
1
1
2
2
2
2
2
RET
*
*
RETI
∆
*
∆
*
STOP (1)
WAIT
*
*
Notes:
1.
This instruction is deactivated<N>and a WAIT is automatically executed instead of a STOP if the watchdog function is selected.
∆ . Affected
*.
Not Affected
Table 21. Jump & Call Instructions
Instruction
Flags
Addressing Mode
Bytes
Cycles
Z
*
C
*
CALL abc
JP abc
Extended
Extended
2
2
4
4
*
*
Notes:
abc. 12-bit address;
* . Not Affected
55/78
ST62T52C ST62T62C/E62C
Opcode Map Summary. The following table contains an opcode map for the instructions used by the ST6
LOW
LOW
0
0000
1
0001
2
0010
3
0011
4
0100
5
0101
6
0110
7
0111
HI
HI
2
JRNZ 4
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
JRNC
5
JRR
b0,rr,ee
bt
JRS
b0,rr,ee
bt
JRR
b4,rr,ee
bt
JRS
b4,rr,ee
bt
JRR
b2,rr,ee
bt
JRS
b2,rr,ee
bt
JRR
b6,rr,ee
bt
JRS
b6,rr,ee
bt
JRR
b1,rr,ee
bt
JRS
b1,rr,ee
bt
JRR
b5,rr,ee
bt
JRS
b5,rr,ee
bt
JRR
b3,rr,ee
bt
JRS
b3,rr,ee
bt
JRR
b7,rr,ee
bt
JRS
b7,rr,ee
2
JRZ
2
JRC
4
LD
0
0
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
#
x
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
a,(x)
0000
0000
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
4
ind
LDI
5
INC 2
1
0001
1
a,nn
0001
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
imm
CP
5
2
0010
2
#
a,(x)
0010
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
e
1
2
pcr
JRZ 4
1
prc
JRC
1
4
ind
CPI
5
LD 2
3
0011
3
a,x
#
a,nn
0011
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
imm
ADD
a,(x)
5
4
0100
4
e
e
e
e
e
e
e
e
e
e
e
e
0100
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
4
ind
ADDI
5
INC 2
5
0101
5
y
a,nn
0101
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
imm
INC
5
6
0110
6
#
(x)
#
0110
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
ind
5
LD 2
7
0111
7
a,y
#
0111
1
2
pcr 2
JRNZ 4
e
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
5
4
1
LD
ind
8
1000
8
(x),a
#
1000
1
2
pcr 2
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
RNZ
e
4
5
INC 2
9
1001
9
v
1001
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
5
4
AND
a,(x)
A
1010
A
1010
e
e
e
e
e
e
#
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
4
ind
ANDI
5
LD 2
B
1011
B
1011
a,v
#
a,nn
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
imm
SUB
5
C
1100
C
1100
a,(x)
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
4
ind
SUBI
5
INC 2
D
1101
D
1101
w
a,nn
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
imm
DEC
5
E
1110
E
1110
#
(x)
#
1
2
pcr 2
JRNZ 4
pcr 3
JRNC
1
2
pcr
JRZ 4
1
prc
JRC
1
ind
5
LD 2
F
1111
F
1111
a,w
1
pcr 2
ext 1
pcr 3
bt
1
pcr 1
sd 1
prc
Abbreviations for Addressing Modes: Legend:
dir
sd
Direct
Short Direct
#
e
b
rr
nn
Indicates Illegal Instructions
5 Bit Displacement
3 Bit Address
1byte dataspace address
1 byte immediate data
Cycle
Mnemonic
2
1
JRC
prc
Operand
imm Immediate
e
inh
ext
b.d
bt
Inherent
Extended
Bit Direct
Bit Test
Bytes
abc 12 bit address
ee 8 bit Displacement
Addressing Mode
pcr
Program Counter Relative
ind
Indirect
56/78
ST62T52C ST62T62C/E62C
Opcode Map Summary (Continued)
LOW
LOW
8
1000
9
1001
A
1010
B
1011
C
1100
D
1101
E
1110
F
1111
HI
HI
2
JRNZ 4
JP 2
JRNC
4
RES 2
b0,rr
b.d 1
SET 2
b0,rr
b.d 1
RES 2
b4,rr
JRZ 4
LDI
2
JRC
4
LD
0
0
e
e
e
e
e
e
e
e
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
rr,nn
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
a,(y)
a,rr
0000
0000
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 3
JRZ 4
imm 1
DEC 2
prc
JRC
1
4
ind
LD
4
1
0001
1
x
a
0001
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
sd 1
COM
prc
JRC
2
4
dir
CP
4
2
2
0010
2
a,(y)
a,rr
0010
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
b.d 1
SET 2
pcr
JRZ 4
1
prc
JRC
1
4
ind
CP
4
LD 2
sd 1
3
0011
3
b4,rr
e
b.d 1
x,a
0011
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 2
prc
JRC
2
4
dir
ADD
a,(y)
4
RES 2
b2,rr
b.d 1
SET 2
b2,rr
b.d 1
RES 2
b6,rr
b.d 1
SET 2
b6,rr
b.d 1
RES 2
b1,rr
b.d 1
SET 2
b1,rr
b.d 1
RES 2
b5,rr
b.d 1
SET 2
b5,rr
b.d 1
RES 2
b3,rr
b.d 1
SET 2
b3,rr
b.d 1
RES 2
b7,rr
b.d 1
SET 2
b7,rr
RETI 2
4
0100
4
e
e
e
e
e
e
e
e
e
e
e
e
0100
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
inh 1
DEC 2
prc
JRC
1
4
ind
ADD
4
5
0101
5
y
a,rr
(y)
rr
0101
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 2
sd 1
STOP 2
prc
JRC
2
4
dir
INC
4
6
0110
6
0110
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
inh 1
LD 2
prc
JRC
1
4
ind
INC
4
7
0111
7
y,a
0111
1
2
pcr 2
JRNZ 4
e
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ
sd 1
2
prc
JRC
2
4
dir
LD
4
8
1000
8
#
v
(y),a
rr,a
1000
1
2
pcr 2
ext 1
JP 2
pcr 2
JRNC
pcr
JRZ 4
1
prc
JRC
1
4
ind
LD
RNZ
e
4
4
DEC 2
9
1001
9
1001
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
sd 1
RCL
prc
JRC
2
4
dir
AND
a,(y)
4
2
A
1010
A
1010
e
e
e
e
e
e
a
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
inh 1
LD 2
prc
JRC
1
4
ind
AND
4
B
1011
B
1011
v,a
a,rr
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 2
sd 1
RET 2
prc
JRC
2
4
dir
SUB
4
C
1100
C
1100
a,(y)
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
inh 1
DEC 2
prc
JRC
1
4
ind
SUB
4
D
1101
D
1101
w
a,rr
(y)
rr
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 2
sd 1
WAIT 2
prc
JRC
2
4
dir
DEC
4
E
1110
E
1110
1
2
pcr 2
JRNZ 4
ext 1
JP 2
pcr 2
JRNC
pcr 1
JRZ 4
inh 1
LD 2
prc
JRC
1
4
ind
DEC
4
F
1111
F
1111
w,a
1
pcr 2
ext 1
pcr 2
b.d 1
pcr 1
sd 1
prc
2
dir
Abbreviations for Addressing Modes: Legend:
dir
sd
Direct
Short Direct
#
e
b
rr
nn
Indicates Illegal Instructions
5 Bit Displacement
3 Bit Address
1byte dataspace address
1 byte immediate data
Cycle
Mnemonic
2
1
JRC
prc
Operand
imm Immediate
e
inh
ext
b.d
bt
Inherent
Extended
Bit Direct
Bit Test
Bytes
abc 12 bit address
ee 8 bit Displacement
Addressing Mode
pcr
Program Counter Relative
ind
Indirect
57/78
ST62T52C ST62T62C/E62C
6 ELECTRICAL CHARACTERISTICS
6.1 ABSOLUTE MAXIMUM RATINGS
This product contains devices to protect the inputs
against damage due to high static voltages, how-
ever it is advisable to take normal precaution to
avoid application of any voltage higher than the
specified maximum rated voltages.
Power Considerations.The average chip-junc-
tion temperature, Tj, in Celsius can be obtained
from:
Tj=TA + PD x RthJA
Where:TA = Ambient Temperature.
For proper operation it is recommended that V
I
RthJA =Package thermal resistance (junc-
tion-to ambient).
and V be higher than V and lower than V .
O
SS
DD
Reliability is enhanced if unused inputs are con-
nected to an appropriate logic voltage level (V
PD = Pint + Pport.
DD
or V ).
SS
Pint =IDD x VDD (chip internal power).
Pport =Port power dissipation (determined
by the user).
Symbol
Parameter
Value
Unit
V
V
Supply Voltage
Input Voltage
Output Voltage
-0.3 to 7.0
DD
(1)
(1)
V
V
V
- 0.3 to V + 0.3
V
I
SS
SS
DD
V
- 0.3 to V + 0.3
V
O
DD
IV
Total Current into V (source)
80
100
mA
mA
°C
°C
DD
DD
IV
Total Current out of V (sink)
SS
SS
Tj
Junction Temperature
Storage Temperature
150
T
-60 to 150
STG
Notes:
-
Stresses above those listed as “absolute maximum ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
- (1) Within these limits, clamping diodes are guarantee to be not conductive. Voltages outside these limits are authorised aslong as injection
current is kept within the specification.
58/78
ST62T52C ST62T62C/E62C
6.2 RECOMMENDED OPERATING CONDITIONS
Value
Unit
Symbol
Parameter
Test Conditions
6 Suffix Version
1 Suffix Version
3 Suffix Version
Min.
Typ.
Max.
-40
0
-40
85
70
TA
Operating Temperature
°C
125
f
f
= 4MHz, 1 & 6 Suffix
= 4MHz, 3 Suffix
3.0
3.0
3.6
4.5
6.0
6.0
6.0
6.0
OSC
OSC
Operating Supply Voltage
V
(Except ST626xB ROM devices) fosc= 8MHz , 1 & 6 Suffix
fosc= 8MHz , 3 Suffix
VDD
f
f
= 4MHz, 1 & 6 Suffix
= 4MHz, 3 Suffix
3.0
3.0
4.0
4.5
6.0
6.0
6.0
6.0
OSC
OSC
Operating Supply Voltage
(ST626xB ROM devices)
V
fosc= 8MHz , 1 & 6 Suffix
fosc= 8MHz , 3 Suffix
V
V
V
V
= 3.0V, 1 & 6 Suffix
= 3.0V , 3 Suffix
= 3.6V , 1 & 6 Suffix
= 3.6V , 3 Suffix
0
0
0
0
4.0
4.0
8.0
4.0
DD
DD
DD
DD
2)
Oscillator Frequency
MHz
MHz
(Except ST626xB ROM devices)
f
OSC
V
V
V
V
= 3.0V, 1 & 6 Suffix
= 3.0V , 3 Suffix
= 4.0V , 1 & 6 Suffix
0
0
0
0
4.0
4.0
8.0
4.0
DD
DD
DD
DD
2)
Oscillator Frequency
(ST626xB ROM devices)
= 4.0V , 3 Suffix
IINJ+
IINJ-
Pin Injection Current (positive)
VDD = 4.5 to 5.5V
+5
-5
mA
mA
Pin Injection Current (negative) VDD = 4.5 to 5.5V
Notes:
1. Care must be taken in case of negative current injection, where adapted impedance must be respected on analog sources to not affect the
A/D conversion. For a -1mA injection, a maximum 10 KΩ is recommended.
2.An oscillator frequency above 1MHz is recommended for reliable A/D results
Figure 30. Maximum Operating FREQUENCY (Fmax) Versus SUPPLY VOLTAGE (VDD)
Maximum FREQUENCY (MHz)
1 & 6 Suffix version
8
FUNCTIONALITY IS NOT
3 Suffix version
1 & 6 Suffix
version
GUARANTEED IN
7
THIS AREA
6
5
4
3 Suffix version
3
2
1
3.6
2.5
3
4
4.5
5
5.5
6
SUPPLY VOLTAGE (VDD)
All devices except ST626xB ROM devices
ST626xB ROM devices
The shaded area is outside the recommended operating range; device functionality is not guaranteed under these conditions.
59/78
ST62T52C ST62T62C/E62C
6.3 DC ELECTRICAL CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
V
Min.
Max.
x 0.3
V
Input Low Level Voltage
All Input pins
IL
V
DD
V
Input High Level Voltage
All Input pins
IH
V
x 0.7
V
DD
(1)
Hysteresis Voltage
All Input pins
V
V
= 5V
= 3V
0.2
0.2
DD
DD
V
V
Hys
V
LVD Threshold in power-on
LVD threshold inpowerdown
4.1
3.8
4.3
up
V
3.5
dn
Low Level Output Voltage
All Output pins
V
V
= 5.0V; I = +10µA
0.1
0.8
DD
DD
OL
= 5.0V; I = + 3mA
OL
V
V
V
V
V
= 5.0V; I = +10µA
0.1
0.8
1.3
OL
DD
DD
DD
OL
Low Level Output Voltage
30 mA Sink I/O pins
= 5.0V; I = +7mA
OL
= 5.0V; I = +15mA
OL
High Level Output Voltage
All Output pins
V
V
= 5.0V; I = -10µA
4.9
3.5
DD
DD
OH
V
V
OH
= 5.0V; I = -3.0mA
OH
All Input pins
RESET pin
40
100
350
350
900
R
Pull-up Resistance
ΚΩ
PU
150
Input Leakage Current
All Input pins but RESET
V
V
= V (No Pull-Up configured)
IN
IN
SS
0.1
-16
1.0
= V
I
I
DD
IL
µA
Input Leakage Current
RESET pin
V
V
= V
-8
-30
10
IH
IN
IN
SS
= V
DD
Supply Current in RESET
Mode
V
=V
=8MHz
RESET
SS
7
7
mA
mA
mA
µA
f
OSC
Supply Current in
V
=5.0V f =8MHz
INT
(2)
DD
RUN Mode
Supply Current in WAIT
I
V
=5.0V
f =8MHz
INT
2.5
20
500
(3)
DD
DD
Mode
Supply Current in STOP
Mode, with LVD disabled
I
V
=0mA
=5.0V
LOAD
(3)
DD
Supply Current in STOP
Mode, with LVD enabled
I
V
=0mA
=5.0V
LOAD
(3)
DD
Retention EPROM Data Retention
TA = 55°C
10
years
Notes:
(1) Hysteresis voltage between switching levels
(2) All peripherals running
(3) All peripherals in stand-by
60/78
ST62T52C ST62T62C/E62C
DC ELECTRICAL CHARACTERISTICS (Cont’d)
(T = -40 to +85°C unless otherwise specified))
A
Value
Unit
Symbol
Parameter
Test Conditions
Min.
+50 mV 4.1
dn
Typ.
Max.
V
LVD Threshold in power-on
LVD threshold inpowerdown
V
4.3
V
V
up
V
3.6
3.8
V
-50 mV
dn
up
V
V
V
= 5.0V; I = +10µA
0.1
0.8
1.2
DD
DD
DD
OL
Low Level Output Voltage
All Output pins
= 5.0V; I = + 5mA
OL
= 5.0V; I = + 10mAv
OL
V
V
V
V
V
V
= 5.0V; I = +10µA
0.1
0.8
1.3
2.0
OL
DD
DD
DD
DD
OL
Low Level Output Voltage
30 mA Sink I/O pins
= 5.0V; I = +10mA
OL
= 5.0V; I = +20mA
OL
= 5.0V; I = +30mA
OL
High Level Output Voltage
All Output pins
V
V
= 5.0V; I = -10µA
4.9
3.5
DD
DD
OH
V
I
V
OH
= 5.0V; I = -5.0mA
OH
Supply Current in STOP
I
=0mA
=5.0V
LOAD
10
µA
(*)
DD
Mode, with LVD disabled
V
DD
Note:
(*) All Peripherals in stand-by.
6.4 AC ELECTRICAL CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
ms
Min.
100
Max.
(1)
t
Supply Recovery Time
REC
TA = 25°C
TA = 85°C
TA = 125°C
5
10
20
10
20
30
T
EEPROM Write Time
ms
WEE
Endurance
EEPROM WRITE/ERASE Cycle
Retention EEPROM Data Retention
QA LOT Acceptance (25°C)
TA = 55°C
300,000 1 million
10
cycles
(2)
years
kHz
f
Internal frequency with LFAO active
200
400
800
LFAO
V
= 3V
1
1
2
2
DD
Internal Frequency with OSG
enabled
V
V
V
= 3.6V
= 4.5V
= 6V
DD
DD
DD
f
f
MHz
2)
OSG
OSC
VDD=5.0V (Except 626xB ROM)
R=47kΩ
R=100kΩ
R=470kΩ
4
2.7
800
5
3.2
850
5.8
3.5
900
MHz
MHz
kHz
Internal frequency with RC oscilla-
tor and OSG disabled
f
2) 3)
VDD=5.0V (626xB ROM)
R=10kΩ
RC
6.3
4.7
2.8
2.2
8.2
5.9
3.6
2.8
9.8
7
4.3
3.4
MHz
MHz
MHz
MHz
R=27kΩ
R=67kΩ
R=100kΩ
C
Input Capacitance
Output Capacitance
All Inputs Pins
10
10
pF
pF
IN
C
All Outputs Pins
OUT
Notes:
1. Period for which V has to be connected at 0V to allow internal Reset function at next power-up.
DD
2 An oscillator frequency above 1MHz is recommended for reliable A/D results.
3. Measure performed with OSCin pin soldered on PCB, with an around 2pF equivalent capacitance.
61/78
ST62T52C ST62T62C/E62C
6.5 A/D CONVERTER CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Typ.
8
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
Res
Resolution
Total Accuracy
Bit
f
f
> 1.2MHz
> 32kHz
±2
±4
(1) (2)
OSC
OSC
A
LSB
TOT
f
f
= 8MHz (T < 85°C)
= 4 MHz
70
140
OSC
OSC
A
t
Conversion Time
Zero Input Reading
Full Scale Reading
µs
C
Conversion result when
= V
ZIR
00
Hex
Hex
V
IN
SS
Conversion result when
V
FSR
FF
= V
IN
DD
Analog Input Current During
Conversion
AD
V
= 4.5V
1.0
5
µA
I
DD
AC
Analog Input Capacitance
2
pF
IN
Notes:
1. Noise at VDD, VSS <10mV
2. With oscillator frequencies less than 1MHz, the A/D Converter accuracy is decreased.
6.6 TIMER CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
fINT
f
t
Input Frequency on TIMER Pin
Pulse Width at TIMER Pin
MHz
IN
W
V
V
= 3.0V
>4.5V
1
125
µs
ns
DD
DD
6.7 SPI CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Symbol
Parameter
Test Conditions
Unit
Min.
Typ.
Max.
500
F
Clock Frequency
Set-up Time
Hold Time
Applied on Scl
Applied on Sin
Applied onSin
kHz
ns
CL
t
250
50
SU
t
ns
h
6.8 ARTIMER ELECTRICAL CHARACTERISTICS
(T = -40 to +125°C unless otherwise specified)
A
Value
Typ
Symbol
Parameter
Test Conditions
Unit
Min
Max
RUN and WAIT Modes
STOP mode
f
Input Frequency on ARTIMin Pin
MHz
IN
2
62/78
ST62T52C ST62T62C/E62C
Figure 31. Vol versus Iol on all I/O port at Vdd=5V
8
6
T = -40°C
T = 25°C
T = 95°C
T = 125°C
4
2
0
0
10
20
30
40
Iol (mA)
This curves represents typical variations and is given for guidance only
Figure 32. Vol versus Iol on all I/O port at T=25°C
8
6
4
2
0
Vdd = 3.0V
Vdd = 4.0V
Vdd = 5.0V
Vdd = 6.0V
0
10
20
30
40
Iol (mA)
This curves represents typical variations and is given for guidance only
Figure 33. Vol versus Iol for High sink (30mA) I/Oports at T=25°C
5
4
3
2
1
0
Vdd = 3.0V
Vdd = 4.0V
Vdd = 5.0V
Vdd = 6.0V
0
10
20
30
40
Iol (mA)
This curves represents typical variations and is given for guidance only
63/78
ST62T52C ST62T62C/E62C
Figure 34. Vol versus Iol for High sink (30mA) I/O ports at Vdd=5V
5
4
3
2
1
0
T = -40°C
T = 25°C
T = 95°C
T = 125°C
0
10
20
30
40
Iol (mA)
This curves represents typical variations and is given for guidance only
Figure 35. Voh versus Ioh on all I/O port at 25°C
6
4
Vdd = 3.0V
Vdd = 4.0V
Vdd = 5.0V
Vdd = 6.0V
2
0
-2
0
10
20
30
40
Ioh (mA)
This curves represents typical variations and is given for guidance only
Figure 36. Voh versus Ioh on all I/O port at Vdd=5V
6
4
2
T = -40°C
T = 25°C
T = 95°C
T = 125°C
0
-2
0
10
20
30
40
Ioh (mA)
This curves represents typical variations and is given for guidance only
64/78
ST62T52C ST62T62C/E62C
Figure 37. Idd WAIT versus V at 8 Mhz for OTP devices
DD
2.5
2
T = -40°C
T = 25°C
T = 95°C
T = 125°C
1.5
1
0.5
0
3V
4V
5V
6V
Vdd
This curves represents typical variations and is given for guidance only
Figure 38. Idd STOP versus V for OTP devices
DD
8
6
T = -40°C
T = 25°C
T = 95°C
T = 125°C
4
2
0
-2
3V
4V
5V
6V
Vdd
This curves represents typical variations and is given for guidance only
Figure 39. Idd STOP versus V for ROM devices
DD
2
1.5
1
T = -40°C
T = 25°C
T = 95°C
T = 125°C
0.5
0
-0.5
3V
4V
5V
6V
Vdd
This curves represents typical variations and is given for guidance only
65/78
ST62T52C ST62T62C/E62C
Figure 40. Idd WAIT versus V at 8Mhz for ROM devices
DD
2.5
2
T = -40°C
T = 25°C
T = 95°C
T = 125°C
1.5
1
0.5
0
3V
4V
5V
6V
Vdd
This curves represents typical variations and is given for guidance only
Figure 41. Idd RUN versus V at 8 Mhz for ROM and OTP devices
DD
8
6
4
2
0
T = -40°C
T = 25°C
T = 95°C
T = 125°C
3V
4V
5V
6V
Vdd
This curves represents typical variations and is given for guidance only
Figure 42. LVD thresholds versus temperature
4.2
4.1
4
Vup
Vdn
3.9
3.8
3.7
-40°C
25°C
95°C
125°C
Temp
This curves represents typical variations and is given for guidance only
66/78
ST62T52C ST62T62C/E62C
Figure 43. RC frequency versus V for ROM ST626xB only
DD
10
R=1OK
R=27K
R=67K
R=100K
1
3
4
5
6
VDD (volts)]
This curves represents typical variations and is given for guidance only
Figure 44. RC frequency versus V (Except for ST626xB ROM devices)
DD
10
R=47K
R=100K
R=470K
1
0.1
3
3.5
4
4.5
5
5.5
6
VDD (volts)
This curves represents typical variations and is given for guidance only
67/78
ST62T52C ST62T62C/E62C
7 GENERAL INFORMATION
7.1 PACKAGE MECHANICAL DATA
Figure 45. 16-Pin Plastic Dual In-Line Package, 300-mil Width
mm
Min Typ Max Min Typ Max
5.33 0.210
inches
Dim.
E
A
A1 0.38
0.015
A2
A
A1
A2 2.92 3.30 4.95 0.115 0.130 0.195
0.36 0.46 0.56 0.014 0.018 0.022
b
L
c
E1
b2 1.14 1.52 1.78 0.045 0.060 0.070
b3 0.76 0.99 1.14 0.030 0.039 0.045
b2
b
eB
e
D1
b3
c
0.20 0.25 0.36 0.008 0.010 0.014
18.67 19.18 19.69 0.735 0.755 0.775
D
D
D1 0.13
0.005
e
2.54
7.62 7.87 8.26 0.300 0.310 0.325
E1 6.10 6.35 7.11 0.240 0.250 0.280
0.100
E
L
2.92 3.30 3.81 0.115 0.130 0.150
eB
10.92
0.430
Number of Pins
N
16
Figure 46. 16-Pin Ceramic Side-Brazed Dual In-Line Package
mm
Min Typ Max Min Typ Max
3.78 0.149
inches
Dim.
A
A1 0.38
0.015
B
0.36 0.46 0.56 0.014 0.018 0.022
B1 1.14 1.37 1.78 0.045 0.054 0.070
C
D
0.20 0.25 0.36 0.008 0.010 0.014
19.86 20.32 20.78 0.782 0.800 0.818
D1
17.78
0.700
E1 7.04 7.49 7.95 0.277 0.295 0.313
e
2.54
0.100
G
6.35 6.60 6.86 0.250 0.260 0.270
G1 9.47 9.73 9.98 0.373 0.383 0.393
G2
L
1.02
0.040
2.92 3.30 3.81 0.115 0.130 0.150
S
1.27
4.22
0.050
0.166
CDIP16W
Ø
Number of Pins
16
N
68/78
ST62T52C ST62T62C/E62C
PACKAGE MECHANICAL DATA (Cont’d)
Figure 47. 16-Pin Plastic Small Outline Package, 300-mil Width
D
mm
inches
h x 45×
Dim.
A
L
Min Typ Max Min Typ Max
A
2.35
2.65 0.093
0.30 0.004
0.51 0.013
0.32 0.009
10.50 0.398
7.60 0.291
10.65 0.394
0.104
0.012
0.020
0.013
0.413
0.299
0.419
C
A1
A1 0.10
a
B
C
D
E
H
e
0.33
0.23
e
B
10.10
7.40
10.00
1.27
0.050
h
α
0.25
0°
0.75 0.010
0.030
8°
H
E
8°
0°
L
0.40
1.27 0.016
0.050
Number of Pins
N
16
Figure 48. 16-Pin Plastic Shrink Small Outline Package
mm
Min Typ Max Min Typ Max
2.00 0.079
inches
D
Dim.
L
A
A2
A
c
A1
A1 0.05
0.002
A2 1.65 1.75 1.85 0.065 0.069 0.073
b
h
e
b
c
0.22
0.09
0.38 0.009
0.25 0.004
0.015
0.010
D
E
5.90 6.20 6.50 0.232 0.244 0.256
7.40 7.80 8.20 0.291 0.307 0.323
E1 5.00 5.30 5.60 0.197 0.209 0.220
e
θ
0.65
0.026
E
E1
0°
4°
8°
0°
4°
8°
L
0.55 0.75 0.95 0.022 0.030 0.037
Number of Pins
N
16
69/78
ST62T52C ST62T62C/E62C
THERMAL CHARACTERISTIC
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
55
PDIP16
PSO16
RthJA
Thermal Resistance
°C/W
75
7.2 ORDERING INFORMATION
Table 22. OTP/EPROM VERSION ORDERING INFORMATION
Program
Sales Type
EEPROM (Bytes)
Temperature Range
Package
Memory (Bytes)
ST62E62CF1
1836 EPROM
64
0 to +70°C
CDIP16W
PSO16
ST62T52CM6
ST62T52CM3
-40 to + 85°C
-40 to + 125°C
1836 OTP
1836 OTP
1836 OTP
1836 OTP
1836 OTP
1836 OTP
None
ST62T62CM6
ST62T62CM3
-40 to + 85°C
-40 to + 125°C
64
None
64
PSO16
PDIP16
PDIP16
SSOP16
SSOP16
ST62T52CB6
ST62T52CB3
-40 to + 85°C
-40 to + 125°C
ST62T62CB6
ST62T62CB3
-40 to + 85°C
-40 to + 125°C
ST62T52CN6
ST62T52CN3
-40 to + 85°C
-40 to + 125°C
None
64
ST62T62CN6
ST62T62CN3
-40 to + 85°C
-40 to + 125°C
70/78
ST62P52C
ST62P62C
8-BIT FASTROM MCUs WITH A/D CONVERTER,
SAFE RESET, AUTO-RELOAD TIMER AND EEPROM
■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +125°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
User selectable size
■ Data RAM: 128 bytes
■ Data EEPROM: 64 bytes (none on ST62T52C)
■ 9 I/O pins, fully programmable as:
– Input with pull-up resistor
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
PDIP16
■ 5 I/O lines can sink up to 30mA to drive LEDs or
TRIACs directly
■ 8-bit Timer/Counter with 7-bit programmable
prescaler
■ 8-bit Auto-reload Timer with7-bit programmable
PSO16
prescaler (AR Timer)
■ Digital Watchdog
■ Oscillator Safe Guard
■ Low Voltage Detector for Safe Reset
■ 8-bit A/D Converter with 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
Crystal Ceramic resonator or RC network
SSOP16
■ User configurable Power-on Reset
■ One external Non-Maskable Interrupt
(See end of Datasheet for Ordering Information)
■ ST626x-EMU2 Emulation and Development
System (connects to an MS-DOS PC via a
parallel port)
DEVICE SUMMARY
ROM
DEVICE
EEPROM
(Bytes)
ST62P52C
ST62P62C
1836
-
1836
64
Rev. 3.0
February 2002
71/78
ST62P52C ST62P62C
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
1.2.2 Listing Generation and Verification
The ST62P52C and ST62P62C are the Factory
Advanced Service Technique ROM (FASTROM)
version of ST62T52C and ST62T62C OTP devic-
es.
When STMicroelectronics receives the user’s
ROM contents, a computer listing is generated
from it. This listing refers exactly to the ROM con-
tents and options which will be used to produce
the specified MCU. The listing is then returned to
the customer who must thoroughly check, com-
plete, sign and return it to STMicroelectronics. The
signed listing forms a part of the contractual agree-
ment for the production of the specific customer
MCU.
They offer the same functionality as OTP devices,
selecting as FASTROM options the options de-
fined in the programmable option byte of the OTP
version.
1.2 ORDERING INFORMATION
The STMicroelectronics Sales Organization will be
pleased to provide detailed information on con-
tractual points.
The following section deals with the procedure for
transfer of customer codes to STMicroelectronics.
1.2.1 Transfer of Customer Code
Customer code is made up of the ROM contents
and the list of the selected FASTROM options.
The ROM contents are to be sent on diskette, or
by electronic means, with the hexadecimal file
generated by the development tool. All unused
bytes must be set to FFh.
Table 23. ROM Memory Map ST62P52C/P62C
Device Address
Description
0000h-087Fh
0880h-0F9Fh
0FA0h-0FEFh
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Reserved
User ROM
Reserved
The selected options are communicated to STMi-
croelectronics using the correctly filled OPTION
LIST appended. See page 76.
Interrupt Vectors
Reserved
NMI Interrupt Vector
Reset Vector
Table 24. FASTROM version Ordering Information
Sales Type
ROM
EEPROM (Bytes)
Temperature Range
Package
ST62P52CM1/XXX
ST62P52CM6/XXX
ST62P52CM3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
1836 Bytes
None
PSO16
ST62P62CM1/XXX
ST62P62CM6/XXX
ST62P62CM3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
1836 Bytes
1836 Bytes
1836 Bytes
1836 Bytes
1836 Bytes
64
None
64
ST62P52CB1/XXX
ST62P52CB6/XXX
ST62P52CB3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
PDIP16
ST62P62CB1/XXX
ST62P62CB6/XXX
ST62P62CB3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
ST62P52CN1/XXX
ST62P52CN6/XXX
ST62P52CN3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
None
64
SSOP16
ST62P62CN1/XXX
ST62P62CN6/XXX
ST62P62CN3/XXX (*)
0 to +70°C
-40 to + 85°C
-40 to + 125°C
(*) Advanced information
72/78
ST6252C
ST6262B
8-BIT ROM MCUs WITH A/D CONVERTER,
SAFE RESET AUTO-RELOAD TIMER, ROM AND EEPROM
■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +125°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
User selectable size
■ Data RAM: 128 bytes
■ Data EEPROM: 64 bytes (none on ST62T52C)
■ 9 I/O pins, fully programmable as:
PDIP16
– Input with pull-up resistor
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
■ 5 I/O lines can sink up to 30mA to drive LEDs or
TRIACs directly
■ 8-bit Timer/Counter with 7-bit programmable
prescaler
■ 8-bit Auto-reload Timer with7-bit programmable
PSO16
prescaler (AR Timer)
■ Digital Watchdog
■ Oscillator Safe Guard
■ Low Voltage Detector for Safe Reset
■ 8-bit A/D Converter with 4 analog inputs
■ On-chip Clock oscillator can be driven by Quartz
Crystal Ceramic resonator or RC network
SSOP16
■ User configurable Power-on Reset
■ One external Non-Maskable Interrupt
(See end of Datasheet for Ordering Information)
■ ST626x-EMU2 Emulation and Development
System (connects to an MS-DOS PC via a
parallel port)
DEVICE SUMMARY
ROM
DEVICE
EEPROM
LVD & OSG
(Bytes)
ST6252C
ST6262B
1836
-
Yes
No
1836
64
Rev. 3.0
February 2002
73/78
ST6252C ST6262B
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
They offer the same functionality as OTP devices,
selecting as ROM options the options defined in
the programmable option byte of the OTP version,
except the LVD & OSG options that are not availa-
ble on the ST6262B ROM device.
The ST6252C and ST6262B are mask pro-
grammed ROM version of ST62T52C and
ST62T62C OTP devices.
Figure 1. Programming Waveform
In case the user wants to blow this fuse, high volt-
age must be applied on the TEST pin.
0.5s min
TEST
Figure 2. Programming Circuit
15
14V typ
10
5
5V
47mF
100nF
TEST
150 µs typ
V
V
SS
100mA
max
DD
PROTECT
14V
TEST
4mA typ
t
100nF
ZPD15
15V
VR02001
VR02003
1.2 ROM READOUT PROTECTION
If the ROM READOUT PROTECTION option is
selected, a protection fuse can be blown to pre-
vent any access to the program memory content.
Note: ZPD15 is used for overvoltage protection
74/78
ST6252C ST6262B
1.3 ORDERING INFORMATION
from it. This listing refers exactly to the mask which
will be used to produce the specified MCU. The
listing is then returned to the customer who must
thoroughly check, complete, sign and return it to
STMicroelectronics. The signed listing forms a
part of the contractual agreement for the creation
of the specific customer mask.
The following section deals with the procedure for
transfer of customer codes to STMicroelectronics.
1.3.1 Transfer of Customer Code
Customer code is made up of the ROM contents
and the list of the selected mask options. The
ROM contents are to be sent on diskette, or by
electronic means, with the hexadecimal file gener-
ated by the development tool. All unused bytes
must be set to FFh.
The STMicroelectronics Sales Organization will be
pleased to provide detailed information on con-
tractual points.
Table 25. ROM Memory Map for ST6252C/62B
The selected mask options are communicated to
STMicroelectronics using the correctly filled OP-
TION LIST appended. See page 76.
Device Address
Description
0000h-087Fh
0880h-0F9Fh
0FA0h-0FEFh
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Reserved
User ROM
Reserved
1.3.2 Listing Generation and Verification
Interrupt Vectors
Reserved
NMI Interrupt Vector
Reset Vector
When STMicroelectronics receives the user’s
ROM contents, a computer listing is generated
Table 26. ROM version Ordering Information
Sales Type
ROM
EEPROM (Bytes)
Temperature Range
Package
ST6252CB1/XXX
ST6252CB6/XXX
ST6252CB3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
PDIP16
ST6252CM1/XXX
ST6252CM6/XXX
ST6252CM3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
1836 Bytes
None
PSO16
SSOP16
PDIP16
PSO16
ST6252CN1/XXX
ST6252CN6/XXX
ST6252CN3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
ST6262BB1/XXX
ST6262BB6/XXX
ST6262BB3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
ST6262BM1/XXX
ST6262BM6/XXX
ST6262BM3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
1836 Bytes
64
ST6262BN1/XXX
ST6262BN6/XXX
ST6262BN3/XXX
0 to +70°C
-40 to + 85°C
-40 to + 125°C
SSOP16
75/78
ST6252C ST6262B
ST6252C/62B/P52C/P62C MICROCONTROLLER OPTION LIST
Customer:
Address:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact:
Phone:
Reference:
STMicroelectronics references:
Device:
[ ] ST6252C (2 KB)
[ ] ST62P52C (2 KB)
[ ] ST6262B (2 KB)
[ ] ST62P62C (2 KB)
Package:
[ ] Dual in Line Plastic
[ ] Small Outline Plastic with conditioning
[ ] Shrink Small Outline Plastic with conditioning
Conditioning option:
Temperature Range:
[ ] Standard (Tube)
[ ] 0°C to + 70°C
[ ] - 40°C to + 125°C
[ ] Tape & Reel
[ ] - 40°C to + 85°C
Marking:
[ ] Standard marking
[ ] Special marking (ROM only):
PDIP16 (9 char. max): _ _ _ _ _ _ _ _ _
PSO16 (6 char. max): _ _ _ _ _ _
SSOP16 (10 char. max): _ _ _ _ _ _ _ _ _ _
Authorized characters are letters, digits, ’.’, ’-’, ’/’ and spaces only.
Oscillator Safeguard*:
Oscillator Selection:
[ ] Enabled
[ ] Quartz crystal / Ceramic resonator
[ ] RC network
[ ] Disabled
Reset Delay:
Watchdog Selection:
PB3:PB2 pull-up at RESET*:
External STOP Mode Control:
[ ] 32768 cycle delay
[ ] Software Activation
[ ] Enabled
[ ] 2048 cycle delay
[ ] Hardware Activation
[ ] Disabled
[ ] Enabled
[ ] Disabled
Readout Protection:
FASTROM:
[ ] Enabled
[ ] Disabled
ROM:
[ ] Enabled:
[ ] Fuse is blown by STMicroelectronics
[ ] Fuse can be blown by the customer
[ ] Disabled
Low Voltage Detector*:
NMI pull-up*:
ADC Synchro*:
[ ] Enabled
[ ] Enabled
[ ] Enabled
[ ] Disabled
[ ] Disabled
[ ] Disabled
*except on ST6262B
Comments:
Oscillator Frequency in the application:
Supply Operating Range in the application:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes:
Date:
Signature:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76/78
ST6252C ST6262B
2 SUMMARY OF CHANGES
Rev.
Main Changes
Modification of “Additional Notes for EEPROM Parallel Mode” (p.13)
Date
Changed f values in section 6.4 on page 61
RC
In section 4.2 on page 41: vector #4 instead of vector #3 for the timer interrupt request.
Changed Figure 43 on page 67.
Changed Figure 45. on page 68 and Figure 47.and Figure 48. on page 69.
Changed option list on page 76.
2.9
3.0
July 2001
Swapped D11 and D10 description on page 14:
D11. Reserved, must be cleared.
Feb 2002
D10. Reserved, must be set to one.
77/78
ST6252C ST6262B
Notes:
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2002 STMicroelectronics - All Rights Reserved.
Purchase of I2C Components by STMicroelectronics conveys a license under the Philips I2C Patent. Rights to use these components in an
I2C system is granted provided that the system conforms to the I2C Standard Specification as defined by Philips.
STMicroelectronics Group of Companies
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
78/78
相关型号：
ST6262BN1
8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, SAFE RESET, AUTO-RELOAD TIMER AND EEPROM
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明