ST62E40BG1 [ETC]
8-Bit Microcontroller ; 8位微控制器\n
| 型号： | ST62E40BG1 |
| 厂家： | 
ETC |
| 描述： | 8-Bit Microcontroller
|
| 文件： | 总74页 (文件大小：445K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ST62T40B/E40B
8-BIT OTP/EPROM MCU WITH LCD DRIVER,
EEPROM AND A/D CONVERTER
■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +85°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
User selectable size
■ Data RAM: 192 bytes
■ Data EEPROM: 128 bytes
■ User Programmable Options
■ 24 I/O pins, fully programmable as:
– Input with pull-up resistor
PQFP80
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
– LCD segments (8 combiport lines)
■ 4 I/O lines can sink up to 20mA to drive LEDs or
TRIACs directly
■ Two
8-bit
Timer/Counter
with
7-bit
programmable prescaler
■ Digital Watchdog
■ 8-bit A/D Converter with 12 analog inputs
■ 8-bit Synchronous Peripheral Interface (SPI)
■ LCD driver with 45 segment outputs, 4
backplane outputs and selectable multiplexing
ratio.
CQFP80W
■ 32kHz oscillator for stand-by LCD operation
■ Power Supply Supervisor (PSS)
■ On-chip Clockoscillator canbe driven by Quartz
(See end of Datasheet for Ordering Information)
Crystal or Ceramic resonator
■ One external Non-Maskable Interrupt
■ ST6240-EMU2 Emulation and Development
System (connects to an MS-DOS PC via a
parallel port).
DEVICE SUMMARY
OTP
(Bytes)
EPROM EEPROM
DEVICE
I/O Pins
(Bytes)
(Bytes)
ST62T40B 7948
ST62E40B
-
128
16 to 24
16 to 24
7948
128
Rev. 2.7
July 2001
1/74
1
Table of Contents
Document
Page
ST62T40B/E40B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3 MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.2 Program Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.3 Data Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3.4 Stack Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.3.5 Data Window Register (DWR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.3.6 Data RAM/EEPROM Bank Register (DRBR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.3.7 EEPROM Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.4 PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4.1 Option Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4.2 Program Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4.3 EEPROM Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.4.4 EPROM Erasing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . 18
3.1 CLOCK SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.1 Main Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.1.2 32 KHz STAND-BY OSCILLATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2 RESETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 RESET Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.2 Power-on Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.3 Watchdog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.4 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2.5 MCU Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3 DIGITAL WATCHDOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.3.1 Digital Watchdog Register (DWDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3.2 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.4 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.4.1 Interrupt request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.4.2 Interrupt Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4.3 Interrupt Option Register (IOR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.4.4 Interrupt sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.5 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5.1 WAIT Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5.2 STOP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5.3 Exit from WAIT and STOP Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.1 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
74
4.1.1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.1.2 Safe I/O State Switching Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2/74
2
Table of Contents
Document
Page
4.1.3 LCD alternate functions (combiports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.1.4 SPI alternate functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.1.5 I/O Port Option Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.1.6 I/O Port Data Direction Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.1.7 I/O Port Data Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.2 TIMER 1 & 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.2.1 TIMER 1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2.2 TIMER 2 Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2.3 Timer Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2.4 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2.5 TIMER 1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.6 TIMER 2 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.3 A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.3.1 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.4 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.5 LCD CONTROLLER-DRIVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.5.1 Multiplexing ratio and frame frequency setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.5.2 Segment and common plates driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.5.3 LCD RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.5.4 Stand by or STOP operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.5.5 LCD Mode Control Register (LCDCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.6 POWERSUPPLY SUPERVISOR DEVICE (PSS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.6.1 PSS Operating Mode Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.6.2 PSS Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5 SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.1 ST6 ARCHITECTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.2 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5.3 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.1 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.2 RECOMMENDED OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3 DC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.4 AC ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.5 A/D CONVERTER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.6 TIMER CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.7 SPI CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.8 LCD ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.9 PSS ELECTRICAL CHARACTERISTICS (WHEN AVAILABLE) . . . . . . . . . . . . . . . . . . . . 65
7 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
7.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
7.2 PACKAGE THERMAL CHARACTERISTIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.3 .ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
3/74
3
Table of Contents
Document
Page
ST6240B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
1.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
1.2 ROM READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
1.3 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
1.3.1 Transfer of Customer Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
1.3.2 Listing Generation and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
2 SUMMARY OF CHANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
74
4/74
4
ST62T40B/E40B
1 GENERAL DESCRIPTION
1.1 INTRODUCTION
The ST62T40B and ST62E40B devices are low
cost members of the ST62xx 8-bit HCMOS family
of microcontrollers, which are targeted at low to
medium complexity applications. All ST62xx de-
vices are based on a building block approach: a
common core is surrounded by a number of on-
chip peripherals.
The ST62E40B is the erasable EPROM version of
the ST62T40B device, which may be used to em-
ulate the ST62T40B device, as well as the respec-
tive ST6240B ROM devices.
Figure 1. Block Diagram
PORT A
PORT B
PA0..PA7/Ain
8-BIT
A/D CONVERTER
TEST/V
PB0..PB3/Ain
PB4/20mA Sink
PP
TEST
PB5/Scl/20mA Sink
PB6/Sin/20mA Sink
PB7/Sout/20mA Sink
NMI
INTERRUPT
DATA ROM
USER
PORT C
PC0..PC7/S33..S40
SELECTABLE
S4..S32, S41..S48
COM1..COM4
PROGRAM
Memory
LCD DRIVER
DATA RAM
192 Bytes
VLCD
VLCD1/3
VLCD2/3
7948 bytes
OSC32in
DATA EEPROM
128 Bytes
OSC 32kHz
OSC32out
TIMER 2
TIMER 1
TIMER
WDON
PC
DIGITAL
WATCHDOG
STACK LEVEL 1
STACK LEVEL 2
STACK LEVEL 3
STACK LEVEL 4
STACK LEVEL 5
STACK LEVEL 6
SPI (SERIAL
PERIPHERAL
INTERFACE)
8 BIT CORE
POWER SUPPLY
SUPERVISOR
PSS
POWER
SUPPLY
RESET
RESET
OSCILLATOR
V
V
OSCin OSCout
DD SS
VA0479
(V on EPROM/OTP versions only)
PP
5/74
5
ST62T40B/E40B
INTRODUCTION (Cont’d)
OTP and EPROM devices are functionally identi-
cal. The ROM based versions offer the same func-
tionality selecting as ROM options the options de-
fined in the programmable option byte of the
OTP/EPROM versions.OTP devices offer all the
advantages of user programmability at low cost,
which make them the ideal choice in a wide range
of applications where frequent code changes, mul-
tiple code versions or last minute programmability
are required.
Figure 2. 80 Pin QFP Package
80
65
1
2
3
64
These compact low-cost devices feature two Tim-
ers comprising an 8-bit counter and a 7-bit pro-
grammable prescaler, EEPROM data capability, a
serial synchronous port interface (SPI), an 8-bit
A/D Converter with 12 analog inputs, a Digital
Watchdog timer, and a complete LCD controller
driver, making them well suited for a wide range of
automotive, appliance and industrial applications.
24
41
VR01649A
25
40
Table 1. ST6240 Pin Description
Pin
Pin
Pin
Pin
Pin
Pin
Pin
Pin
number
name
number
name
number
name
number
name
1
2
S43
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
RESET
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
PSS
65
S27
S44
OSCout
OSCin
S4
66
S28
3
S45
S5
67
S29
4
S46
WDON
S6
68
S30
5
S47
NMI
S7
69
S31
6
S48
TIMER
S8
70
S32
7
COM4
COM3
COM2
COM1
VLCD1/ 3
VLCD2/ 3
VLCD
PB7/ Sout *
PB6/ Sin*
PB5/ SCL *
PB4 *
S9
71
PC0/S33
PC1/S34
PC2/S35
PC3/S36
PC4/S37
PC5/S38
PC6/S39
PC7/S40
S41
8
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
72
9
73
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
74
PB3/ Ain
PB2/ Ain
PB1/ Ain
PB0/ Ain
OSC32out
OSC32in
75
76
77
PA7/ Ain
PA6/ Ain
PA5/ Ain
PA4/ Ain
TEST
78
79
80
S42
PA3/ Ain
PA2/ Ain
PA1/ Ain
PA0/ Ain
VDD
VSS
*Note: 20mA Sink
6/74
6
ST62T40B/E40B
1.2 PIN DESCRIPTIONS
and V . Power is supplied to the MCU via
V
TIMER. This is the TIMER 1 I/O pin. In input mode,
it is connected to the prescaler and acts as ex-
ternal timer clock or as control gate for the internal
timer clock. In output mode, the TIMER pin outputs
the data bit when a time-out occurs.The user can
select as option the availability of an on-chip pull-
up at this pin.
DD
SS
these two pins. V is the power connection and
DD
V
is the ground connection.
SS
OSCin and OSCout. These pins are internally
connected to the on-chip oscillator circuit. A quartz
crystal, a ceramic resonator or an external clock
signal can be connected between these two pins.
The OSCin pin is the input pin, the OSCout pin is
the output pin.
COM1-COM4. These four pins are the LCD pe-
ripheral common outputs. They are the outputs of
the on-chip backplane voltage generator which is
used for multiplexing the 45 LCD lines allowing up
to 180 segments to be driven.
RESET. The active-low RESET pin is used to re-
start the microcontroller.
TEST/VPP. The TEST must be held at VSS for nor-
mal operation (an internal pull-down resistor se-
lects normal operating mode if TEST pin is not
connected). If TEST pin is connected to a +12.5V
level during the reset phase, the EPROM/OTP
programming Mode is entered.
S4-S48. These pins are the 45 LCD peripheral
segment outputs. S33..S40 are alternate functions
of the Port C I/O pins. (Combiports feature)
VLCD. Display voltage supply. It determines the
high voltage level on COM1-COM4 and S4-S48
pins.
NMI. The NMI pin provides the capability for asyn-
chronous interruption, by applying an external non
maskable interrupt to the MCU. Schmitt trigger
characteristics. The user can select as option the
availability of an on-chip pull-up at this pin.
VLCD1/3, VLCD2/3. Display supply voltage inputs
for determining the display voltage levels on
COM1-COM4 and S4-S48 pins during multiplex
operation.
PA0-PA7. These 8 lines are organised as one I/O
port (A). Each line may be configured under soft-
ware control as input with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull output, or
as analog inputs for the A/D converter.
PSS. This is the Power Supply Supervisor sensing
pin. When the voltage applied to this pin is falling
below a software programmed value the highest
priority (NMI) interrupt can be generated. This pin
has to be connected to the voltage to be super-
vised.
PB0...PB7. These 8 lines are organised as one I/O
port (B). Each line may be configured under soft-
ware control as inputs with or without internal pull-
up resistors, input with interrupt generation and
pull-up resistor, open-drain or push-pull outputs,
analog inputs for the A/D converter. PB0..PB3 can
be used as analog inputs for the A/D converter ,
while PB7/Sout, PB6/Sin and PB5/Scl can be used
respectively as data out, data in and Clock pins for
the on-chip SPI. In addition, PB4..PB7 can sink
20mA for direct LED or TRIAC drive.
OSC32in and OSC32out. These pins are inter-
nally connected with the on-chip 32kHz oscillator
circuit. A 32.768kHz quartz crystal can be con-
nected between these two pins if it is necessary to
provide the LCD stand-by clock and real time inter-
rupt. OSC32in is the input pin, OSC32out is the
output pin.
WDON. This pin is an alternate and external
source of controlling the watchdog activation, in-
dependantly of the options set into the MCU by the
user. A low level selects the hardware activated
watchdog, while a high level selects the software
activated watchdog for low consumption modes.
This pin overcomes the option byte content. How-
ever if WDON pin state is different from option byte
content, extra consumption must be expected.
PC0-PC7. These 8 lines are organised as one I/O
port (C). Each line may be configured under soft-
ware control as input with or without internal pull-
up resistor, input with interrupt generation and
pull-up resistor, open-drain or push-pull output, or
as LCD segment output S33..S40.
7/74
7
ST62T40B/E40B
1.3 MEMORY MAP
1.3.1 Introduction
common (STATIC) 2K page is available all the
time for interrupt vectors and common subrou-
tines, independently of the PRPR register content.
This “STATIC” page is directly addressed in the
0800h-0FFFh by the MSB of the Program Counter
register PC 11. Note this page can also be ad-
dressed in the 000-7FFh range. It is two different
ways of addressing the same physical memory.
The MCU operates in three separate memory
spaces: Program space, Data space, and Stack
space. Operation in these three memory spaces is
described in the following paragraphs.
Briefly, Program space contains user program
code in Program memory and user vectors; Data
space contains user data in RAM and in Program
memory, and Stack space accommodates six lev-
els of stack for subroutine and interrupt service
routine nesting.
Jump from a dynamic page to another dynamic
page is achieved by jumping back to the static
page, changing contents of PRPR and then jump-
ing to the new dynamic page.
1.3.2 Program Space
Figure 3. 8Kbytes Program Space Addressing
Program Space comprises the instructions to be
executed, the data required for immediate ad-
dressing mode instructions, the reserved factory
test area and the user vectors. Program Space is
addressed via the 12-bit Program Counter register
(PC register).
ROM SPACE
PC
1FFFh
Page 3
SPACE
000h
0000h
Page 1
Static
Page
Page 0
Page 2
7FFh
800h
Program Space is organised in four 2K pages.
Three of them are addressed in the 000h-7FFh lo-
cations of the Program Space by the Program
Counter and by writing the appropriate code in the
Program ROM Page Register (PRPR register). A
Page 1
Static
Page
FFFh
Figure 4. Memory Addressing Diagram
PROGRAM SPACE
DATA SPACE
0000h
000h
RAM / EEPROM
BANKING AREA
0-63
03Fh
040h
DATA READ-ONLY
WINDOW
MEMORY
PROGRAM
MEMORY
07Fh
080h
081h
082h
083h
084h
X REGISTER
Y REGISTER
V REGISTER
W REGISTER
RAM
DATA READ-ONLY
MEMORY
WINDOW SELECT
0C0h
0FF0h
DATA RAM
INTERRUPT &
RESET VECTORS
0FFFh
BANK SELECT
ACCUMULATOR
0FFh
VR01568
8/74
8
ST62T40B/E40B
MEMORY MAP (Cont’d)
Table 2. ST62E40B/T40B Program MemoryMap
Program ROM Page Register (PRPR)
Address: CAh
7
— Write Only
ROM Page Device Address
Description
0000h-007Fh
Page 0
Reserved
User ROM
0
0080h-07FFh
-
-
-
-
-
-
PRPR1 PRPR0
0800h-0F9Fh
0FA0h-0FEFh
User ROM
Reserved
Page 1
“STATIC”
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Interrupt Vectors
Bits 7-2= Not used.
Reserved
NMI Vector
Reset Vector
Bits 1-0 = PRPR1-PRPR0: Program ROM Select.
These two bits select the corresponding page to
be addressed in the lower part of the 4K program
address space as specified in Table 3.
0000h-000Fh
0010h-07FFh
Reserved
User ROM
Page 2
Page 3
0000h-000Fh
0010h-07FFh
Reserved
User ROM
Caution: This register is undefined on Reset. Nei-
ther read nor single bit instructions may be used to
address this register.
Note: OTP/EPROM devices can be programmed
with thedevelopment toolsavailable fromSTMicro-
electronics (ST62E4X-EPB or ST6240-KIT).
Table 3. 8Kbytes Program ROM Page Register
Coding
PRPR1
PRPR0 PC bit 11
Memory Page
Static Page (Page 1)
Page 0
X
0
0
1
1
X
0
1
0
1
1
0
0
0
0
1.3.2.1 Program ROM Page Register (PRPR)
The PRPR register can be addressed like a RAM
location in the Data Space at the address CAh ;
nevertheless it is a write only register that cannot
be accessed with single-bit operations. This regis-
ter is used to select the 2-Kbyte ROM bank of the
Program Space that will be addressed. The
number of the page has to be loaded in the PRPR
register. Refer to the Program Space description
for additional information concerning the use of
this register. The PRPR register is not modified
when an interrupt or a subroutine occurs.
Page 1 (Static Page)
Page 2
Page 3
1.3.2.2 Program Memory Protection
The Program Memory in OTP or EPROM devices
can be protected against external readout of mem-
ory by selecting the READOUT PROTECTION op-
tion in the option byte.
In the EPROM parts, READOUT PROTECTION
option can be disactivated only by U.V. erasure
that also results into the whole EPROM context
erasure.
Care is required when handling the PRPR register
as it is write only. For this reason, it is not allowed
to change the PRPR contents while executing in-
terrupt service routine, as the service routine
cannot save and then restore its previous content.
This operation may be necessary if common rou-
tines and interrupt service routines take more than
2K bytes ; in this case it could be necessary to di-
vide the interrupt service routine into a (minor) part
in the static page (start and end) and to a second
(major) part in one of the dynamic pages. If it is im-
possible to avoid the writing of this register in inter-
rupt service routines, an image of this register
must be saved in a RAM location, and each time
the program writes to the PRPR it must write also
to the image register. The image register must be
written before PRPR, so if an interrupt occurs be-
tween the two instructions the PRPR is not af-
fected.
Note: Once the Readout Protection is activated, it
is no longer possible, even for STMicroelectronics,
to gain access to the Program memory contents.
Returned parts with a protection set can therefore
not be accepted.
9/74
9
ST62T40B/E40B
MEMORY MAP (Cont’d)
1.3.3 Data Space
Table 5. ST62T40B/E40B Data Memory Space
000h
03Fh
040h
DATA and EEPROM
Data Space accommodates all the data necessary
for processing the user program. This space com-
prises the RAM resource, the processor core and
peripheral registers, as well as read-only data
such as constants and look-up tables in Program
memory.
DATAROM WINDOW AREA
07Fh
X REGISTER
Y REGISTER
V REGISTER
W REGISTER
080h
081h
082h
083h
084h
1.3.3.1 Data ROM
DATA RAM
0BFh
0C0h
0C1h
0C2h
0C3h
0C4h
0C5h
0C6h
0C7h
0C8h*
0C9h*
0CAh*
0CBh*
0CCh
0CDh
0CEh
0CFh
0D0h
0D1h
0D2h
0D3h
0D4h
0D5h
0D6h
0D7h
0D8h
0D9h
0DAh
0DBh
0DCh
0DDh
0DEh
0DFh
0E0h
All read-only data is physically stored in program
memory, which also accommodates the Program
Space. The program memory consequently con-
tains the program code to be executed, as well as
the constants and look-up tables required by the
application.
PORT A DATA REGISTER
PORT B DATA REGISTER
SPI INTERRUPT DISABLE REGISTER
PORT C DATAREGISTER
PORT A DIRECTION REGISTER
PORT B DIRECTION REGISTER
PORT C DIRECTION REGISTER
RESERVED
INTERRUPT OPTION REGISTER
DATA ROM WINDOW REGISTER
ROM BANK SELECT REGISTER
RAM/EEPROM BANK SELECT REGISTER
PORT A OPTION REGISTER
RESERVED
The Data Space locations in which the different
constants and look-up tables are addressed by the
processor core may be thought of as a 64-byte
window through which it is possible to access the
read-only data stored in Program memory.
1.3.3.2 Data RAM/EEPROM
In ST62T40B and ST62E40B devices, the data
space includes 60 bytes of RAM, the accumulator
(A), the indirect registers (X), (Y), the short direct
registers (V), (W), the I/O port registers, the pe-
ripheral data and control registers, the interrupt
option register and the Data ROM Window Regis-
ter (DRW register).
PORT B OPTION REGISTER
PORT C OPTION REGISTER
A/D DATA REGISTER
A/D CONTROL REGISTER
TIMER 1 PRESCALER REGISTER
TIMER 1 COUNTER REGISTER
TIMER 1 STATUS/CONTROL REGISTER
TIMER 2 PRESCALER REGISTER
TIMER 2 COUNTER REGISTER
TIMER 2 STATUS/CONTROL REGISTER
WATCHDOG REGISTER
Additional RAM and EEPROM pages can also be
addressed using banks of 64 bytes located be-
tween addresses 00h and 3Fh.
1.3.4 Stack Space
RESERVED
PSS STATUS/CONTROL REGISTER
32kHz OSCILLATOR CONTROL REGISTER
LCD MODE CONTROL REGISTER
SPI DATAREGISTER
Stack space consists of six 12-bit registers which
are used to stack subroutine and interrupt return
addresses, as well as the current program counter
contents.
RESERVED
EEPROM CONTROL REGISTER
Table 4. Additional RAM/EEPROM Banks.
LCD RAM
0F7h
0F8h
0FEh
OFFh
Device
RAM
EEPROM
DATA RAM
ST62T40B/E40B
2 x 64 bytes
2 x 64 bytes
ACCUMULATOR
* WRITE ONLY REGISTER
10/74
10
ST62T40B/E40B
MEMORY MAP (Cont’d)
1.3.5 Data Window Register (DWR)
Data Window Register (DWR)
Address: 0C9h
— Write Only
The Data Read-Only Memory window is located
from address 0040h to address 007Fh in Data
space. It allows direct reading of 64 consecutive
bytes located anywhere in program memory, be-
tween address 0000h and 1FFFh (top memory ad-
dress depends on the specific device). All the pro-
gram memory can therefore be used to store either
instructions or read-only data. Indeed, the window
can be moved in steps of 64 bytes along the pro-
gram memoryby writing theappropriate code in the
Data Window Register (DWR).
7
0
-
-
DWR5 DWR4 DWR3 DWR2 DWR1 DWR0
Bits 6, 7 = Not used.
Bit 5-0 = DWR5-DWR0: Data read-only memory
Window Register Bits. These are the Data read-
only memory Window bits that correspond to the
upper bits of the data read-only memory space.
The DWR can beaddressed like any RAM location
in the Data Space, it is however a write-only regis-
ter and therefore cannot be accessed using single-
bit operations. This register is used to position the
64-byte read-only data window (from address 40h
to address 7Fh of the Data space) in program
memory in 64-byte steps. The effective address of
the byte to be read as data in program memory is
obtained by concatenating the 6 least significant
bits of the register address given in the instruction
(as least significant bits) and the content of the
DWR register (as most significant bits), as illustrat-
ed in Figure 5 below. For instance, when address-
ing location 0040h of the Data Space, with 0 load-
ed in the DWR register, the physical location ad-
dressed inprogram memory is 00h. The DWR reg-
ister is not cleared on reset, therefore it must be
written to prior to the first access to the Data read-
only memory window area.
Caution: This register is undefined on reset. Nei-
ther read nor single bit instructions may be used to
address this register.
Note: Care is required when handling the DWR
register as it is write only. For this reason, the
DWR contents should not be changed while exe-
cuting an interrupt service routine, as the service
routine cannot save and then restore the register’s
previous contents. If it is impossible to avoid writ-
ing to the DWR during the interrupt service routine,
an image of the register must be saved in a RAM
location, and each time the program writes to the
DWR, it must also write to the image register. The
image register must be written first so that, if an in-
terrupt occurs between the two instructions, the
DWR is not affected.
Figure 5. Data read-only memory Window Memory Addressing
13 12 11 10
9
3
8
2
7
1
6
0
5
4
3
2
1
1
0 PROGRAM SPACE ADDRESS
READ
DATA ROM
WINDOW REGISTER
CONTENTS
7
6
5
4
5
4
3
2
0
DATA SPACE ADDRESS
40h-7Fh
(DWR)
0
1
IN INSTRUCTION
Example:
DWR=28h
0
0
1
0
0
1
0
0
0
0
0
1
DATA SPACE ADDRESS
59h
0
0
1
1
1
0
0
0
0
1
ROM
ADDRESS:A19h
0
0
1
1
1
1
VR01573A
11/74
11
ST62T40B/E40B
MEMORY MAP (Cont’d)
1.3.6 Data RAM/EEPROM Bank Register
(DRBR)
This register is not cleared during the MCU initiali-
zation, therefore it must be written before the first
access to the Data Space bank region. Refer to
the Data Space description for additional informa-
tion. The DRBR register is not modified when an
interrupt or a subroutine occurs.
Address: CBh — Write only
7
-
0
-
-
DRBR4 DRBR3
-
DRBR1 DRBR0
Notes :
Care is required when handling the DRBR register
as it is write only. For this reason, it is not allowed
to change the DRBR contents while executing in-
terrupt service routine, as the service routine can-
not save and then restore its previous content. If it
is impossible to avoid the writing of this register in
interrupt service routine, an image of this register
must be saved in a RAM location, and each time
the program writes to DRBR it must write also to
the image register. The image register must be
written first, so if an interrupt occurs between the
two instructions the DRBR is not affected.
Bit 7-5 = These bits are not used
Bit 4 - DRBR4. This bit, when set, selects RAM
Page 2.
Bit 3 - DRBR3. This bit, when set, selects RAM
Page 1.
Bit2. These bits are not used.
Bit 1 - DRBR1. This bit, when set, selects
EEPROM Page 1.
Bit 0 - DRBR0. This bit, when set, selects
EEPROM Page 0.
In DRBR Register, only 1 bit must be set. Other-
wise two or more pages are enabled in parallel,
producing errors.
The selection of the bank is made by programming
the Data RAM Bank Switch register (DRBR regis-
ter) located at address CBh of the Data Space ac-
cording to Table 1. No more than one bank should
be set at a time.
Table 6. Data RAM Bank Register Set-up
DRBR
00h
ST62T40B/E40B
None
The DRBR register can be addressed like a RAM
Data Space at the address CBh; nevertheless it is
a write only register that cannot be accessed with
single-bit operations. This register is used to select
the desired 64-byte RAM/EEPROM bank of the
Data Space. The number of banks has to be load-
ed in the DRBR register and the instruction has to
point to the selected location as if it was in bank 0
(from 00h address to 3Fh address).
01h
EEPROM Page 0
EEPROM Page 1
RAM Page 1
RAM Page 2
Reserved
02h
08h
10h
other
12/74
12
ST62T40B/E40B
MEMORY MAP (Cont’d)
1.3.7 EEPROM Description
(PMODE). In BMODE, one byte is accessed at a
time, while in PMODE up to 8 bytes in the same
row are programmed simultaneously (with conse-
quent speed and power consumption advantages,
the latter being particularly important in battery
powered circuits).
EEPROM memory is located in 64-byte pages in
data space. This memory may be used by the user
program for non-volatile data storage.
Data space from 00h to 3Fh is paged as described
in Table 7. EEPROM locations are accessed di-
rectly by addressing these paged sections of data
space.
General Notes:
Data should be written directly to the intended ad-
dress in EEPROM space. There is no buffer mem-
ory between data RAM and the EEPROM space.
The EEPROM does not require dedicated instruc-
tions forreadorwrite access. Onceselectedvia the
Data RAM Bank Register, the active EEPROM
page is controlled by the EEPROM Control Regis-
ter (EECTL), which is described below.
When the EEPROM is busy (E2BUSY = “1”)
EECTL cannot be accessed in write mode, it is
only possible to read the status of E2BUSY. This
implies that as long as the EEPROM is busy, it is
not possible to change the status of the EEPROM
Control Register. EECTL bits 4 and 5 are reserved
and must never be set.
Bit E20FFof the EECTL registermust beresetprior
to any write or read access to the EEPROM. If no
bank hasbeen selected, orif E2OFF is set, any ac-
cess is meaningless.
Care is required when dealing withthe EECTL reg-
ister, as some bits are write only. For this reason,
the EECTL contents must not be altered while ex-
ecuting an interrupt service routine.
Programming must be enabled by setting the
E2ENA bit of the EECTL register.
The E2BUSY bit of the EECTL register is set when
the EEPROM is performing a programming cycle.
Any access to the EEPROM when E2BUSY is set
is meaningless.
If it is impossible to avoid writing to this register
within an interrupt service routine, an image of the
register must be saved in a RAM location, and
each time the program writes to EECTL it must
also write to the image register. The image register
must be written to first so that, if an interrupt oc-
curs between the two instructions, the EECTL will
not be affected.
Provided E2OFF and E2BUSY are reset, an EEP-
ROM location is read just like any other data loca-
tion, also in terms of access time.
Writing to the EEPROM may be carried out in two
modes: Byte Mode (BMODE) and Parallel Mode
Table 7. Row Arrangement for Parallel Writing of EEPROM Locations
Dataspace
addresses.
Banks 0 and 1.
Byte
0
1
2
3
4
5
6
7
ROW7
ROW6
ROW5
ROW4
ROW3
ROW2
ROW1
ROW0
38h-3Fh
30h-37h
28h-2Fh
20h-27h
18h-1Fh
10h-17h
08h-0Fh
00h-07h
Up to 8 bytes in each row may be programmed simultaneously in Parallel Write mode.
The number of available 64-byte banks (1 or 2) is device dependent.
13/74
13
ST62T40B/E40B
MEMORY MAP (Cont’d)
Additional Notes on Parallel Mode:
Bit 6= E2OFF: Stand-by EnableBit. WRITE ONLY.
If thisbit is settheEEPROM isdisabled(anyaccess
will bemeaningless) and the power consumption of
the EEPROM is reduced to its lowest value.
If the user wishes to perform parallel program-
ming, the first step should be to set the E2PAR2
bit. From this time on, the EEPROM will be ad-
dressed in write mode, the ROW address will be
latched and it will be possible to change it only at
the end of the programming cycle, or by resetting
E2PAR2 without programming the EEPROM. Af-
ter the ROW address is latched, the MCU can only
“see” the selected EEPROM row and any attempt
to write or read other rows will produce errors.
Bit 5-4 = D5-D4: Reserved. MUST be kept reset.
Bit 3 = E2PAR1: Parallel Start Bit. WRITE ONLY.
Once inParallelMode,as soonas theuser software
sets the E2PAR1 bit, parallel writing of the 8 adja-
cent registers will start. This bit is internally reset at
the end of the programming procedure. Note that
less than 8 bytes can be written if required, the un-
defined bytes being unaffected by the parallel pro-
gramming cycle;this is explained in greater detail in
the Additional Notes on Parallel Mode overleaf.
The EEPROM should not be read while E2PAR2
is set.
As soon as the E2PAR2 bit is set, the 8 volatile
ROW latches are cleared. From this moment on,
the user can load data in all or in part of the ROW.
Setting E2PAR1 will modify the EEPROM regis-
ters corresponding to the ROW latches accessed
after E2PAR2. For example, if the software sets
E2PAR2 and accesses the EEPROM by writing to
addresses 18h, 1Ah and 1Bh, and then sets
E2PAR1, these three registers will be modified si-
multaneously; the remaining bytes in the row will
be unaffected.
Bit 2 = E2PAR2: Parallel Mode En. Bit. WRITE
ONLY. This bit must be set by the user program in
order to perform parallel programming. If E2PAR2
is set and the parallel start bit (E2PAR1) is reset,
up to 8 adjacent bytes can be written simultane-
ously. These 8 adjacent bytes are considered as a
row, whose address lines A7, A6, A5, A4, A3 are
fixed while A2, A1 and A0 are the changing bits, as
illustrated in Table 7. E2PAR2 is automatically re-
set at the end of any parallel programming proce-
dure. It can be reset by the user software before
starting the programming procedure, thus leaving
the EEPROM registers unchanged.
Note that E2PAR2 is internally reset at the end of
the programming cycle. This implies that the user
must set the E2PAR2 bit between two parallel pro-
gramming cycles. Note that if the user tries to set
E2PAR1 while E2PAR2 is not set, there will be no
programming cycle and the E2PAR1 bit will be un-
affected. Consequently, the E2PAR1 bit cannot be
set if E2ENA is low. The E2PAR1 bit can be set by
the user, only if the E2ENA and E2PAR2 bits are
also set.
Bit 1 = E2BUSY: EEPROM Busy Bit. READ ON-
LY. This bit is automatically set by the EEPROM
control logic when the EEPROM is in program-
ming mode. The user program should test it before
any EEPROM read or write operation; any attempt
to access the EEPROM while the busy bit is set
will be aborted and the writing procedure in
progress will be completed.
EEPROM Control Register (EECTL)
Bit 0 = E2ENA: EEPROM Enable Bit. WRITE ON-
LY. This bit enables programming of the EEPROM
cells. It must be set before any write to the EEP-
ROM register. Any attempt to write to the EEP-
ROM when E2ENA is low is meaningless and will
not trigger a write cycle.
Address: DFh
—
Read/Write
Reset status: 00h
7
0
D7 E2OFF D5
D4 E2PAR1 E2PAR2 E2BUSY E2ENA
Caution: This register is undefined on reset. Nei-
ther read nor single bit instructions may be used to
address this register.
Bit 7 = D7: Unused.
14/74
14
ST62T40B/E40B
1.4 PROGRAMMING MODES
1.4.1 Option Byte
The Option byte is written during programming ei-
ther by using the PC menu (PC driven Mode) or
automatically (stand-alone mode)
The Option Byte allows configuration capability to
the MCUs. Option byte’s content is automatically
read, and the selected options enabled, when the
chip reset is activated.
1.4.2 Program Memory
EPROM/OTP programming mode is set by a
+12.5V voltage applied to the TEST/V pin. The
PP
It can only be accessed during the programming
mode. This access is made either automatically
(copy from a master device) or by selecting the
OPTION BYTE PROGRAMMING modeof the pro-
grammer.
programming flow of the ST62T40B/E40B is de-
scribed in the User Manual of the EPROM Pro-
gramming Board.
The MCUs can be programmed with the
ST62E4xB EPROM programming tools available
from STMicroelectronics.
The option byte is located in a non-user map. No
address has to be specified.
1.4.3 EEPROM Data Memory
EPROM Code Option Byte
EEPROM data pages are supplied in the virgin
state FFh. Partial or total programming of EEP-
ROM data memory can be performed either
through the application software, or through an ex-
ternal programmer. Any STMicroelectronics tool
used for the program memory (OTP/EPROM) can
also be used to program the EEPROM data mem-
ory.
7
-
0
-
NMI
PULL TECT
PRO-
TIM
PULL
-
WDACT
-
Bit 7. Reserved.
Bit 6 = NMI PULL. . This bit must be set high to re-
move the NMI pin pull up resistor. When it is low, a
pull up is provided.
1.4.4 EPROM Erasing
The EPROM of the windowed package of the
MCUs may be erased by exposure to Ultra Violet
light. The erasure characteristic of the MCUs is
such that erasure begins when the memory is ex-
posed to light with a wave lengths shorter than ap-
proximately 4000Å. It should be noted that sun-
lights and some types of fluorescent lamps have
wavelengths in the range 3000-4000Å.
Bit 5 = PROTECT. This bit allows the protection of
the software contents against piracy. When the bit
PROTECT is set high, readout of the OTP con-
tents is prevented by hardware. No programming
equipment is able to gain access to the user pro-
gram. When this bit is low, the user program can
be read.
It is thus recommended that the window of the
MCUs packages be covered by an opaque label to
prevent unintentional erasure problems when test-
ing the application in such an environment.
Bit 4. Reserved.
Bit 3 = WDACT. This bit controls the watchdog ac-
tivation. When it is high, hardware activation is se-
lected. The software activation is selected when
WDACT is low.
The recommended erasure procedure of the
MCUs EPROM is the exposure to short wave ul-
traviolet light which have a wave-length 2537A.
The integrated dose (i.e. U.V. intensity x exposure
time) for erasure should be a minimum of 15W-
Bit 2 = TIM PULL. This bit must be set high to con-
figure the TIM pin with a pull up resistor when it is
low, no pull up is provided.
2
sec/cm . The erasure time with this dosage is ap-
Bit 1-0 = Reserved.
proximately 15 to 20 minutes using an ultraviolet
2
lamp with 12000µW/cm power rating. The
ST62E40B should be placed within 2.5cm (1Inch)
of the lamp tubes during erasure.
15/74
15
ST62T40B/E40B
2 CENTRAL PROCESSING UNIT
2.1 INTRODUCTION
The CPUCoreof ST6 devicesis independent of the
I/O or Memory configuration. As such, it may be
thought of as an independent central processor
communicating with on-chip I/O, Memory and Pe-
ripherals via internal address, data, and control
buses. In-core communication is arranged as
shown in Figure 6; the controller being externally
linked to both the Reset and Oscillator circuits,
while thecore is linked to the dedicated on-chip pe-
ripherals via the serial data bus and indirectly, for
interrupt purposes, through the control registers.
Indirect Registers (X, Y). These two indirect reg-
isters are used as pointers to memory locations in
Data space. They are used in the register-indirect
addressing mode. These registers can be ad-
dressed in the data space as RAM locations at ad-
dresses 80h (X) and 81h (Y). They can also be ac-
cessed with the direct, short direct, or bit direct ad-
dressing modes. Accordingly, the ST6 instruction
set can use the indirect registers as any other reg-
ister of the data space.
Short Direct Registers (V, W). These two regis-
ters are used to save a byte in short direct ad-
dressing mode. They can be addressed in Data
space as RAM locations at addresses 82h (V) and
83h (W). They can also be accessed using the di-
rect and bit direct addressing modes. Thus, the
ST6 instruction set can use the short direct regis-
ters as any other register of the data space.
2.2 CPU REGISTERS
The ST6Family CPUcorefeatures sixregistersand
three pairs of flags available to the programmer.
These are described in the following paragraphs.
Accumulator (A). The accumulator is an 8-bit
general purpose register used in all arithmetic cal-
culations, logical operations, and data manipula-
tions. The accumulator can be addressed in Data
space as a RAM location at address FFh. Thus the
ST6 can manipulate the accumulator just like any
other register in Data space.
Program Counter (PC). The program counter is a
12-bit register which contains the address of the
next ROM location to be processed by the core.
This ROM location may be an opcode, an oper-
and, or the address of an operand. The 12-bit
length allows the direct addressing of 4096 bytes
in Program space.
Figure 6. ST6 Core Block Diagram
0,01 TO 8MHz
RESET
OSCin
OSCout
INTERRUPTS
CONTROLLER
DATA SPACE
DATA
CONTROL
SIGNALS
FLAG
VALUES
OPCODE
ADDRESS/READ LINE
ADDRESS
2
RAM/EEPROM
PROGRAM
DATA
ROM/EPROM
256
ROM/EPROM
DECODER
B-DATA
A-DATA
DEDICATIONS
ACCUMULATOR
Program Counter
and
12
FLAGS
6 LAYER STACK
ALU
RESULTS TO DATA SPACE (WRITE LINE)
VR01811
16/74
16
ST62T40B/E40B
CPU REGISTERS (Cont’d)
However, if the program space contains more than
4096 bytes, the additional memory in program
space can be addressed by using the Program
Bank Switch register.
automatically selected after the reset of the MCU,
the ST6 core uses at first the NMI flags.
Stack. The ST6 CPU includes a true LIFO hard-
ware stack which eliminates the need for a stack
pointer. The stack consists of six separate 12-bit
RAM locations that do not belong to the data
space RAM area. When a subroutine call (or inter-
rupt request) occurs, the contents of each level are
shifted into the next higher level, while the content
of the PC is shifted into the first level (the original
contents of the sixth stack level are lost). When a
subroutine or interrupt return occurs (RET or RETI
instructions), the first level register is shifted back
into the PC and the value of each level is popped
back into the previous level. Since the accumula-
tor, in common with all other data space registers,
is not stored in this stack, management of these
registers should be performed within the subrou-
tine. The stack will remain in its “deepest” position
if more than 6 nested calls orinterrupts are execut-
ed, and consequently the last return address will
be lost. It will also remain in its highest position if
the stack is empty and a RET or RETI is executed.
In this case the next instruction will be executed.
The PC value is incremented after reading the ad-
dress of the current instruction. To execute relative
jumps, the PC and the offset are shifted through
the ALU, where they are added; the result is then
shifted back into the PC. The program counter can
be changed in the following ways:
- JP (Jump) instructionPC=Jump address
- CALL instructionPC= Call address
- Relative Branch Instruction.PC= PC +/- offset
- Interrupt
- Reset
PC=Interrupt vector
PC= Reset vector
- RET & RETI instructionsPC= Pop (stack)
- Normal instructionPC= PC + 1
Flags (C, Z). The ST6 CPU includes three pairs of
flags (Carry and Zero), each pair being associated
with one of the three normal modes of operation:
Normal mode, Interrupt mode and Non Maskable
Interrupt mode. Each pair consists of a CARRY
flag and a ZERO flag. One pair (CN, ZN) is used
during Normal operation, another pair is used dur-
ing Interrupt mode (CI, ZI), and a third pair is used
in the Non Maskable Interrupt mode (CNMI, ZN-
MI).
Figure 7. ST6 CPU Programming Mode
l
b7 X REG. POINTER b0
INDEX
REGISTER
SHORT
DIRECT
ADDRESSING
b7 Y REG. POINTER b0
The ST6 CPU uses the pair of flags associated
with the current mode: as soon as an interrupt (or
a Non Maskable Interrupt) is generated, the ST6
CPU uses the Interrupt flags (resp. the NMI flags)
instead of the Normal flags. When the RETI in-
struction is executed, the previously used set of
flags is restored. It should be noted that each flag
set can only be addressed in its own context (Non
Maskable Interrupt, Normal Interrupt or Main rou-
tine). The flags are not cleared during context
switching and thus retain their status.
MODE
V REGISTER
W REGISTER
b7
b7
b0
b0
b7 ACCUMULATOR
PROGRAMCOUNTER
b0
b0
b11
SIX LEVELS
STACKREGISTER
The Carry flag is set when a carry or a borrow oc-
curs during arithmetic operations; otherwise it is
cleared. The Carry flag is also set to the value of
the bit tested in a bit test instruction; it also partici-
pates in the rotate left instruction.
NORMAL FLAGS
INTERRUPT FLAGS
NMI FLAGS
C
C
C
Z
Z
Z
The Zero flag is set if the result of the last arithme-
tic or logical operation was equal to zero; other-
wise it is cleared.
Switching between the three sets of flags is per-
formed automatically when an NMI, an interrupt or
a RETI instructions occurs. As the NMI mode is
VA000423
17/74
17
ST62T40B/E40B
3 CLOCKS, RESET, INTERRUPTS AND POWER SAVING MODES
3.1 CLOCK SYSTEM
3.1.1 Main Oscillator
Figure 8. Oscillator Configurations
The MCU features a Main Oscillator which can be
driven by an external clock, or used in conjunction
with an AT-cut parallel resonant crystal or a suita-
ble ceramic resonator.
CRYSTAL/RESONATOR CLOCK
ST6xxx
Figure 8 illustrates various possible oscillator con-
figurations using anexternal crystal or ceramic res-
OSC
OSC
out
in
onator, an external clock input. C an C should
L1
L2
have a capacitance in the range 12 to 22 pF for an
oscillator frequency in the 4-8 MHz range.
The internal MCU clock Frequency (F ) is divid-
INT
C
ed by 13 to drive the CPU core and by 12 to drive
the A/D converter and the watchdog timer, while
clock used to drive on-chip peripherals depends
on the peripheral as shown in the clock circuit
block diagram.
C
L1n
L2
VA0016
EXTERNAL CLOCK
ST6xxx
With an 8MHz oscillator frequency, the fastest ma-
chine cycle is therefore 1.625µs.
A machine cycle is the smallest unit of time needed
to execute anyoperation (for instance, to increment
the Program Counter). An instruction may require
two, four, or five machine cycles for execution.
OSC
OSC
NC
out
in
VA0015A
Figure 9. Clock Circuit Block Diagram
POR
f
OSC
OSCin
Core
: 13
: 12
f
INT
Timer 1 & 2
f
MAIN
OSCILLATOR
INT
Watchdog
ADC
OSCout
LCD
MUX
CONTROLLER
DRIVER
OSC32in
EOCR bit 5
(START/STOP )
32kHz
OSCILLATOR
OSC32out
18/74
18
ST62T40B/E40B
CLOCK SYSTEM (Cont’d)
3.1.2 32 KHz STAND-BY OSCILLATOR
32KHz Oscillator Register (32OCR)
An additional32KHz stand-by on chip oscillator al-
lows to generate real time interrupts and to supply
the clock to the LCD driver with the main oscillator
stopped. This enables the MCU to perform real
time functions with the LCD display running while
keeping advantages of low power consumption.
Figure 10 shows the 32KHz oscillator block dia-
gram.
Address: DBh - Read/Write
7
0
EOSCI OSCEOC S/S
D4
D3
D2
D1
D0
Bit 7= EOSCI. Enable Oscillator Interrupt. This bit,
when set, enables the 32KHz oscillator interrupt
request.
A 32.768KHz quartz crystal must be connected to
the OSC32in and OSC32out pins to perform the
real time clock operation. Two external capacitors
of 15-22pF each must be connected between the
oscillator pins and ground. The 32KHz oscillator is
managed by the dedicated status/control register
32OCR.
Bit 6 = OSCEOC. Oscillator Interrupt Flag. This bit
indicates when the 32KHz oscillator has measured
a
500ms
elapsed
time
(providing
a
32.768KHzquartz crystal is connected to the
32KHz oscillator dedicated pins). An interrupt re-
quest can be generated in relation to the state of
EOSCI bit. This bit must be cleared by the user
program before leaving the interrupt service rou-
tine.
As long as the 32KHz stand-by oscillator is ena-
bled, 32KHz internal clock is available to drive
14
LCD controller driver. This clock is divide by 2 to
Bit 5 = START/STOP. Oscillator Start/Stop bit.
This bit, when set, enables the 32KHz stand-by
oscillator and the free running divider chain is sup-
plied by the 32KHz oscillator signal. When this bit
is cleared to zero the divider chain is supplied with
generate interrupt request every 500ms . The peri-
odic interrupt request serves as reference time-
base for real time functions.
Note: When the 32KHz stand-by oscillator is
stopped (bit 5 of the Status/Control register
cleared) the divider chain is supplied with a clock
f
/13.
INT
This register is cleared during reset.
signal synchronous with machine cycle (f /13),
INT
14
this produces an interrupt request every 13x2
Note:
clock cycle (i.e. 26.624ms) with an 8MHz quartz
crystal.
To achieve minimum power consumption in STOP
mode (no system clock), the stand-by oscillator
must be switched off (real time function not availa-
ble) by clearing the Start/Stop bit in the oscillator
status/control register.
Figure 10. 32KHz Oscillator Block Diagram
OSC32KHz
2x15...22pF
OSC32IN
1
14
OSC32KHz
MUX
DIV 2
0
32.768KHz
Crystal
OSC32OUT
f
/13
INT
START
STOP
EOSCI OSCEOC
X
X
X
X
X
INT
19/74
19
ST62T40B/E40B
3.2 RESETS
The MCU can be reset in three ways:
– by the external Reset input being pulled low;
– by Power-on Reset;
The internaldelay is generated by an on-chipcoun-
ter. The internal reset line is released 2048 internal
clock cycles after release of the external reset.
Notes:
– by the digital Watchdog peripheral timing out.
3.2.1 RESET Input
To ensure correct start-up, the user should take
care that the reset signal is not released before the
The RESET pin may be connected to a device of
the application board in order to reset the MCU if
required. The RESET pin may be pulled low in
RUN, WAIT or STOP mode. This input can be
used to reset the MCU internal state and ensure a
correct start-up procedure. The pin is active low
and features a Schmitt trigger input. The internal
Reset signal is generated by adding a delay to the
external signal. Therefore even short pulses on
V
level is sufficient to allow MCU operation at
DD
the chosen frequency (see Recommended Oper-
ating Conditions).
A proper reset signal for a slow rising V supply
can generally be provided by an external RC net-
work connected to the RESET pin.
DD
Figure 11. Reset and Interrupt Processing
the RESET pin are acceptable, provided V has
DD
RESET
completed its rising phase and that the oscillator is
running correctly (normal RUN or WAIT modes).
The MCU is kept in the Reset state as long as the
RESET pin is held low.
NMI MASK SET
INT LATCH CLEARED
( IF PRESENT )
If RESET activation occurs in the RUN or WAIT
modes, processing of the user program is stopped
(RUN mode only), the Inputs and Outputs are con-
figured as inputs with pull-up resistors and the
main Oscillator is restarted. When the level on the
RESET pin then goes high, the initialization se-
quence is executed following expiry of the internal
delay period.
SELECT
NMI MODE FLAGS
PUT FFEH
If RESET pin activation occurs in the STOP mode,
the oscillator starts up and all Inputs and Outputs
are configured as inputs with pull-up resistors.
When the level of the RESET pin then goes high,
the initialization sequence is executed following
expiry of the internal delay period.
ON ADDRESS BUS
YES
IS RESET STILL
PRESENT?
3.2.2 Power-on Reset
The function of the POR circuit consists in waking
up the MCU at an appropriate stage during the
power-on sequence. At the beginning of this se-
quence, the MCU is configured in the Reset state:
all I/O ports are configured as inputs with pull-up
resistors and no instruction is executed. When the
power supply voltage rises to a sufficient level, the
oscillator starts to operate, whereupon an internal
delay is initiated, in order to allow the oscillator to
fully stabilize before executing the first instruction.
The initialization sequence is executed immediate-
ly following the internal delay.
NO
LOAD PC
FROM RESET LOCATIONS
FFE/FFF
FETCH INSTRUCTION
VA000427
20/74
20
ST62T40B/E40B
RESETS (Cont’d)
3.2.3 Watchdog Reset
initialisation routine from being interrupted. The in-
itialisation routine should therefore be terminated
by a RETI instruction, in order to revert to normal
mode and enable interrupts. If no pending interrupt
is presentat the end of the initialisation routine, the
MCU will continue by processing the instruction
immediately following the RETI instruction. If, how-
ever, a pending interrupt is present, it will be serv-
iced.
The MCU provides a Watchdog timer function in
order to ensure graceful recovery from software
upsets. If the Watchdog register is not refreshed
before an end-of-count condition is reached, the
internal reset will be activated. This, amongst oth-
er things, resets the watchdog counter.
The MCU restarts just as though the Reset had
been generated by the RESET pin, including the
built-in stabilisation delay period.
Figure 12. Reset and Interrupt Processing
3.2.4 Application Notes
RESET
No external resistor is required between V and
DD
the Reset pin, thanks to the built-in pull-up device.
The POR circuit operates dynamically, in that it
triggers MCU initialization on detecting the rising
JP:2 BYTES/4 CYCLES
JP
RESET
VECTOR
edge of V . The typical threshold is in the region
DD
of 2 volts, but the actual value of the detected
threshold depends on the way in which V rises.
DD
The POR circuit is NOT designed to supervise
static, or slowly rising or falling V
.
DD
INITIALIZATION
ROUTINE
3.2.5 MCU Initialization Sequence
RETI: 1 BYTE/2 CYCLES
When a reset occurs the stack is reset, the PC is
loaded with the address of the Reset Vector (locat-
ed in program ROM starting at address 0FFEh). A
jump to the beginning of the user program must be
coded at this address. Following a Reset, the In-
terrupt flag is automatically set, so that the CPU is
in Non Maskable Interrupt mode; this prevents the
RETI
VA00181
Figure 13. Reset Block Diagram
V
DD
ST6
INTERNAL
RESET
f
CK
OSC
300kΩ
COUNTER
RESET
RESET
RESET
2.8kΩ
ON RESET
POWER
WATCHDOG RESET
VA0200B
21/74
21
ST62T40B/E40B
RESETS (Cont’d)
Table 8. Register Reset Status
Register
Address(es)
0DFh
Status
Comment
EEPROM enabled
EEPROM Control Register
Port Data Registers
0C0h, 0C2h, 0C3h
0C4h to 0C5h
0CCh, 0CEh
0C8h
Port A,B Direction Register
Port A,B Option Register
Interrupt Option Register
I/O are Input with pull-up
Interrupt disabled
00h
SPI Registers
0C2h to 0DDh
0DCh
SPI disabled
LCD Mode Control Register
32kHz Oscillator Register
LCD display off
Interrupt disabled
0DBh
Port C Direction Register
Port C Option Register
0C6h
0CFh
FFh
LCD Output
X, Y,V, W, Register
Accumulator
080H TO083H
0FFh
Data RAM
084h to 0BFh
0CBh
Data RAM Page REgister
Data ROM Window Register
EEPROM
Undefined
As written if programmed
0C9h
00h to 03Fh
0D0h
A/D Result Register
TIMER 1 Status/Control
TIMER 1 Counter Register
TIMER 1 Prescaler Register
0D4h
0D3h
0D2h
00h
FFh
7Fh
TIMER 1 disabled/Max count loaded
TIMER 2 disabled/Max count loaded
A/D in Standby
TIMER 2 Status/Control
TIMER 2 Counter Register
TIMER 2 Prescaler Register
0D7h
0D5h
0D6h
00h
FFh
7Fh
Watchdog Counter Register
A/D Control Register
0D8h
0D1h
FEh
40h
22/74
22
ST62T40B/E40B
3.3 DIGITAL WATCHDOG
The digital Watchdog consists of a reloadable
downcounter timer which can be used to provide
controlled recovery from software upsets.
Watchdog behaviour is governed by one option,
known as “WATCHDOG ACTIVATION” (i.e.
HARDWARE or SOFTWARE) (See Table 9).
The Watchdog circuit generates a Reset when the
downcounter reaches zero. User software can
prevent this reset by reloading the counter, and
should therefore be written so that the counter is
regularly reloaded while the user program runs
correctly. In the event of a software mishap (usual-
ly caused by externally generated interference),
the user program will no longer behave in its usual
fashion and the timer register will thus not be re-
loaded periodically. Consequently the timer will
decrement down to 00h and reset the MCU. In or-
der to maximise the effectiveness of the Watchdog
function, user software must be written with this
concept in mind.
In the SOFTWARE option, the Watchdog is disa-
bled until bit C of the DWDR register has been set.
When the Watchdog is disabled, low power Stop
mode is available. Once activated, the Watchdog
cannot be disabled, except by resetting the MCU.
In the HARDWARE option, the Watchdog is per-
manently enabled. Since the oscillator will run con-
tinuously, low power mode is not available. The
STOP instruction is interpreted as a WAIT instruc-
tion, and the Watchdog continues to countdown.
When the MCU exits STOP mode (i.e. when an in-
terrupt is generated), the Watchdog resumes its
activity.
Table 9. Recommended Option Choices
Functions Required
Stop Mode
Recommended Options
“SOFTWARE WATCHDOG”
“HARDWARE WATCHDOG”
Watchdog
23/74
23
ST62T40B/E40B
DIGITAL WATCHDOG (Cont’d)
The Watchdog is associated with a Data space
register (Digital WatchDog Register, DWDR, loca-
tion 0D8h) which is described in greater detail in
Section 3.3.1 Digital Watchdog Register (DWDR).
This register is set to 0FEh on Reset: bit C is
cleared to “0”, which disables the Watchdog; the
timer downcounter bits, T0 to T5, and the SR bit
are all set to “1”, thus selecting the longest Watch-
dog timer period. This time period can be set to the
user’s requirements by setting the appropriate val-
ue for bits T0 to T5 in the DWDR register. The SR
bit must be set to “1”, since it is this bit which gen-
erates the Reset signal when it changes to “0”;
clearing this bit would generate an immediate Re-
set.
Figure 14. Watchdog Counter Control
D0
C
D1
SR
RESET
D2
D3
D4
D5
D6
D7
T5
T4
T3
T2
T1
T0
It should be noted that the order of the bits in the
DWDR register is inverted with respect to the as-
sociated bits in the down counter: bit 7 of the
DWDR register corresponds, in fact, to T0 and bit
2 to T5. The user should bear in mind the fact that
these bits are inverted and shifted with respect to
the physical counter bits when writing to this regis-
ter. The relationship between the DWDR register
bits and the physical implementation of the Watch-
dog timer downcounter is illustrated in Figure 14.
Only the 6 most significant bits may be used to de-
fine the time period, since it is bit 6 which triggers
the Reset when it changes to “0”. This offers the
user a choice of 64 timed periods ranging from
3,072 to 196,608 clock cycles (with an oscillator
frequency of 8MHz, this is equivalent to timer peri-
ods ranging from 384µs to 24.576ms).
8
÷2
OSC ÷12
VR02068A
24/74
24
ST62T40B/E40B
DIGITAL WATCHDOG (Cont’d)
3.3.1 Digital Watchdog Register (DWDR)
It should be noted that the register bits are re-
versed and shifted with respect to the physical
counter: bit-7 (T0) is the LSB of the Watchdog
downcounter and bit-2 (T5) is the MSB.
Address: 0D8h
— Read/Write
Reset status: 1111 1110b
These bits are set to “1” on Reset.
7
0
3.3.2 Application Notes
T0
T1
T2
T3
T4
T5
SR
C
The Watchdog plays an important supporting role
in the high noise immunity of ST62xx devices, and
should be used wherever possible. Watchdog re-
lated options should be selected on the basis of a
trade-off between application security and STOP
mode availability.
Bit 0 = C: Watchdog Control bit
If the hardware option is selected, this bit is forced
high and the user cannot change it (the Watchdog
is always active). When the software option is se-
lected, the Watchdog function is activated by set-
ting bit C to 1, and cannot then be disabled (save
by resetting the MCU).
When STOP mode is not required, hardware acti-
vation should be preferred, as it provides maxi-
mum security, especially during power-on.
When C is kept low the counter can be used as a
7-bit timer.
When software activation is selected and the
Watchdog is not activated, the downcounter may
be used as a simple 7-bit timer (remember that the
bits are in reverse order).
This bit is cleared to “0” on Reset.
Bit 1 = SR: Software Reset bit
This bit triggers a Reset when cleared.
The software activation option should be chosen
only when the Watchdog counter is to be used as
a timer. To ensure the Watchdog has not been un-
expectedly activated, the following instructions
should be executed within the first 27 instructions:
When C = “0” (Watchdog disabled) it is the MSB of
the 7-bit timer.
This bit is set to “1” on Reset.
Bits 2-7 = T5-T0: Downcounter bits
jrr 0, WD, #+3
25/74
25
ST62T40B/E40B
DIGITAL WATCHDOG (Cont’d)
These instructions test the C bit and Reset the
MCU (i.e. disable the Watchdog) if the bit is set
(i.e. if the Watchdog is active), thus disabling the
Watchdog.
should load the watchdog counter within the first
27 instructions following Watchdog activation
(software mode), or within the first 27 instructions
executed following a Reset (hardware activation).
In all modes, a minimum of 28 instructions are ex-
ecuted after activation, before the Watchdog can
generate a Reset. Consequently, user software
It should be noted that when the GEN bit is low (in-
terrupts disabled), the NMI interrupt is active but
cannot cause a wake up from STOP/WAIT modes.
Figure 15. Digital Watchdog Block Diagram
RESET
Q
RSFF
7
8
-2
-2
-12
R
DB1.7 LOAD SET
SET
S
OSCILLATOR
CLOCK
8
DB0
WRITE
RESET
DATA BUS
VA00010
26/74
26
ST62T40B/E40B
3.4 INTERRUPTS
The CPU can manage four Maskable Interrupt
sources, in addition to a Non Maskable Interrupt
source (top priority interrupt). Each source is asso-
ciated with a specific Interrupt Vector which con-
tains a Jump instruction to the associated interrupt
service routine. These vectors are located in Pro-
gram space (see Table 10).
ically reset by the core at the beginning of the non-
maskable interrupt service routine.
Interrupt request from source #1 can be config-
ured either as edge or level sensitive by setting ac-
cordingly the LES bit of the Interrupt Option Regis-
ter (IOR).
Interrupt request from source #2 are always edge
sensitive. The edge polarity can be configured by
setting accordingly the ESB bit of the Interrupt Op-
tion Register (IOR).
When an interrupt source generates an interrupt
request, and interrupt processing is enabled, the
PC register is loaded with the address of the inter-
rupt vector (i.e. of the Jump instruction), which
then causes a Jump to the relevant interrupt serv-
ice routine, thus servicing the interrupt.
Interrupt request from sources #3 & #4 are level
sensitive.
In edge sensitive mode, a latch is set when a edge
occurs on the interrupt source line and is cleared
when the associated interrupt routine is started.
So, the occurrence of an interrupt can be stored,
until completion of the running interrupt routine be-
fore being processed. If several interrupt requests
occurs before completion of the running interrupt
routine, only the first request is stored.
Interrupt sources are linked to events either on ex-
ternal pins, or on chip peripherals. Several events
can be ORed on the same interrupt source, and
relevant flags are available to determine which
event triggered the interrupt.
The Non Maskable Interrupt request has the high-
est priority and can interrupt any interrupt routine
at any time; the other four interrupts cannot inter-
rupt each other. If more than one interrupt request
is pending, these are processed by the processor
core according to their priority level: source #1 has
the higher priority while source #4 the lower. The
priority of each interrupt source is fixed.
Storage of interrupt requests is not available in lev-
el sensitive mode. To be taken into account, the
low level must be present on the interrupt pin when
the MCU samples the line after instruction execu-
tion.
At the end of every instruction, the MCU tests the
interrupt lines: if there is an interrupt request the
next instruction is not executed and the appropri-
ate interrupt service routine is executed instead.
Table 10. Interrupt Vector Map
Interrupt Source
Interrupt source #0
Interrupt source #1
Interrupt source #2
Interrupt source #3
Interrupt source #4
Priority
Vector Address
(FFCh-FFDh)
(FF6h-FF7h)
(FF4h-FF5h)
(FF2h-FF3h)
(FF0h-FF1h)
1
2
3
4
5
Table 11. Interrupt Option Register Description
SET
Enable all interrupts
Disable all interrupts
GEN
CLEARED
Rising edge mode on inter-
rupt source #2
SET
ESB
3.4.1 Interrupt request
Falling edge mode on inter-
rupt source #2
CLEARED
SET
All interrupt sources but the Non Maskable Inter-
rupt source can be disabled by setting accordingly
the GEN bit of the Interrupt Option Register (IOR).
This GEN bit also defines if an interrupt source, in-
cluding the Non Maskable Interrupt source, can re-
start the MCU from STOP/WAIT modes.
Level-sensitive mode on in-
terrupt source #1
LES
Falling edge mode on inter-
rupt source #1
CLEARED
OTHERS
NOT USED
Interrupt request from the Non Maskable Interrupt
source #0 is latched by a flip flop which is automat-
27/74
27
ST62T40B/E40B
INTERRUPTS (Cont’d)
3.4.2 Interrupt Procedure
MCU
– Automatically the MCU switches back to the nor-
mal flag set (or the interrupt flag set) and pops
the previous PC value from the stack.
The interrupt procedure is very similar to a call pro-
cedure, indeed the user can consider the interrupt
as an asynchronous call procedure. As this is an
asynchronous event, the user cannot know the
context and the time at which it occurred. As a re-
sult, the user should save all Data space registers
which may be used within the interrupt routines.
There are separate sets of processor flags for nor-
mal, interrupt and non-maskable interrupt modes,
which are automatically switched and so do not
need to be saved.
The interrupt routine usually begins by the identify-
ing the device which generated the interrupt re-
quest (by polling). The user should save the regis-
ters which are used within the interrupt routine in a
software stack. After the RETI instruction is exe-
cuted, the MCU returns to the main routine.
Figure 16. Interrupt Processing Flow Chart
The following list summarizes the interrupt proce-
dure:
INSTRUCTION
MCU
FETCH
– The interrupt is detected.
INSTRUCTION
– The C and Z flags are replaced by the interrupt
flags (or by the NMI flags).
EXECUTE
– The PC contents are stored in the first level of
the stack.
INSTRUCTION
– The normal interrupt lines are inhibited (NMI still
active).
– The first internal latch is cleared.
LOAD PC FROM
INTERRUPT VECTOR
NO
WAS
(FFC/FFD)
THE INSTRUCTION
?
A RETI
– Theassociatedinterruptvectorisloaded inthePC.
YES
IS THE CORE
ALREADY IN
NORMAL MODE?
SET
WARNING: In some circumstances, when a
maskable interrupt occurs while the ST6 core is in
NORMAL mode and especially during the execu-
tion of an ”ldi IOR, 00h” instruction (disabling all
maskable interrupts): if the interrupt arrives during
the first 3 cycles of the ”ldi” instruction (which is a
4-cycle instruction) the core will switch to interrupt
mode BUT the flags CN and ZN will NOT switch to
the interrupt pair CI and ZI.
YES
INTERRUPT MASK
?
NO
CLEAR
INTERRUPT MASK
PUSH THE
PC INTO THE STACK
SELECT
PROGRAM FLAGS
SELECT
INTERNAL MODE FLAG
User
”POP”
– User selected registers are saved within the in-
terrupt service routine (normally on a software
stack).
THE STACKED PC
CHECK IF THERE IS
AN INTERRUPT REQUEST
AND INTERRUPTMASK
NO
– Thesource of the interrupt is found by polling the
interrupt flags (if more than one source is associ-
ated with the same vector).
?
YES
VA000014
– The interrupt is serviced.
– Return from interrupt (RETI)
28/74
28
ST62T40B/E40B
INTERRUPTS (Cont’d)
3.4.3 Interrupt Option Register (IOR)
Bit 5 = ESB: Edge Selection bit.
The Interrupt Option Register (IOR) is used to en-
able/disable the individual interrupt sources and to
select the operating mode of the external interrupt
inputs. This register is write-only and cannot be
accessed by single-bit operations.
The bit ESB selects the polarity of the interrupt
source #2.
Bit 4= GEN: Global Enable Interrupt. When this bit
is set to one, all interrupts are enabled. When this
bit is cleared to zero all the interrupts (excluding
NMI) are disabled.
Address: 0C8h
—
Write Only
Reset status: 00h
When the GEN bit is low, the NMI interrupt is ac-
tive but cannot cause a wake up from STOP/WAIT
modes.
7
-
0
-
This register is cleared on reset.
LES ESB GEN
-
-
-
3.4.4 Interrupt sources
Interrupt
sources
available
on
the
Bit 7, Bits 3-0 = Unused.
ST62E40B/T40B are summarized in the Table 12
with associated mask bit to enable/disable the in-
terrupt request.
Bit 6 = LES: Level/Edge Selection bit.
When this bit is set to one, the interrupt source #1
is level sensitive. When cleared to zero the edge
sensitive mode for interrupt request is selected.
Table 12. Interrupt Requests and Mask Bits
Address
Interrupt
source
Peripheral
Register
Mask bit
Masked Interrupt Source
Register
GENERAL
IOR
C8h
GEN
ETI
All Interrupts, excluding NMI All
TIMER 1
TIMER 2
TSCR1
TSCR2
D4h
D7h
TMZ: TIMER Overflow
source 3
A/D CONVERTER ADCR
D1h
EAI
EOC: End of Conversion
End of Transmission
source 4
source 1
source 2
source 2
source 2
source 0
source 3
SPI
SPI
C2h
ALL
Port PAn
Port PBn
Port PCn
PSS
ORPA-DRPA
ORPB-DRPB
C0h-C4h
C1h-C5h
ORPAn-DRPAn PAn pin
ORPBn-DRPBn PBn pin
ORPCn-DRPCn PCn pin
ORPC-DRPC C6h-CFh
PSSCR
32OCR
DAh
DBh
PEI
PIF:
32kHz OSC
EOSCI
OSCEOC
29/74
29
ST62T40B/E40B
INTERRUPTS (Cont’d)
Figure 17. Interrupt Block Diagram
PIF
PEI
PSS
FF
CLK
CLR
INT #0 NMI (FFC,D))
Q
NMI
I
Start
0
FF
CLK
CLR
Q
0
SPI
MUX
INT #1 (FF6,7)
FROM REGISTER PORT A,B,C
SINGLE BIT ENABLE
I
Start
1
1
PBE
IOR bit 6 (LES)
V
DD
RESTART
FROM
STOP/WAIT
PORT A
FF
CLK
CLR
PBE
PBE
PORT B
PORT C
INT #2 (FF4,5)
Q
Bits
I
Start
2
IOR bit 5 (ESB)
TMZ
ETI
TIMER1
TIMER2
TMZ
ETI
INT #3 (FF2,3)
OSCEOC
EOSCI
OSC32kHz
EAI
EOC
INT #4 (FF0,1)
A/D CONVERTER
IOR bit 4(GEN)
VR0426R
30/74
30
ST62T40B/E40B
3.5 POWER SAVING MODES
The WAIT and STOP modes have been imple-
mented in the ST62xx family of MCUs in order to
reduce the product’s electrical consumption during
idle periods. These two power saving modes are
described in the following paragraphs.
of the processor core prior to the WAIT instruction,
but also on the kind of interrupt request which is
generated. This is described in the following para-
graphs. The processor core does not generate a
delay following the occurrence of the interrupt, be-
cause the oscillator clock is still available and no
stabilisation period is necessary.
3.5.1 WAIT Mode
The MCU goes into WAIT mode as soon as the
WAIT instruction is executed. The microcontroller
can be considered as being in a “software frozen”
state where the core stops processing the pro-
gram instructions, the RAM contents and peripher-
al registers are preserved as long as the power
supply voltage is higher than the RAM retention
voltage. In this mode the peripherals are still ac-
tive.
3.5.2 STOP Mode
If the Watchdog is disabled, STOP mode is availa-
ble. When in STOP mode, the MCU is placed in
the lowest power consumption mode. In this oper-
ating mode, the microcontroller can be considered
as being “frozen”, no instruction is executed, the
oscillator is stopped, the RAM contents and pe-
ripheral registers are preserved as long as the
power supply voltage is higher than the RAM re-
tention voltage, and the ST62xx core waits for the
occurrence of an external interrupt request or a
Reset to exit the STOP state.
WAIT mode can be used when the user wants to
reduce the MCU power consumption during idle
periods, while not losing track of time or the capa-
bility of monitoring external events. The active os-
cillator is not stopped in order to provide a clock
signal to the peripherals. Timer counting may be
enabled as well as the Timer interrupt, before en-
tering the WAIT mode: this allows the WAIT mode
to be exited when a Timer interrupt occurs. The
same applies to other peripherals which use the
clock signal.
If the STOP state is exited due to a Reset (by acti-
vating the external pin) the MCU will enter a nor-
mal reset procedure. Behaviour in response to in-
terrupts depends on the state of the processor
core prior to issuing the STOP instruction, and
also on the kind of interrupt request that is gener-
ated.
If the WAIT mode is exited due to a Reset (either
by activating the external pin or generated by the
Watchdog), the MCU enters a normal reset proce-
dure. If an interrupt is generated during WAIT
mode, the MCU’s behaviour depends on the state
This case will be described in the following para-
graphs. The processor core generates a delay af-
ter occurrence of the interrupt request, in order to
wait for complete stabilisation of the oscillator, be-
fore executing the first instruction.
31/74
31
ST62T40B/E40B
POWER SAVING MODE (Cont’d)
3.5.3 Exit from WAIT and STOP Modes
tered will be completed, starting with the
execution of the instruction which follows the
STOP or the WAIT instruction, and the MCU is
still in the interrupt mode. At the end of this rou-
tine pendinginterrupts will be serviced in accord-
ance with their priority.
The following paragraphs describe how the MCU
exits from WAIT and STOP modes, when an inter-
rupt occurs (not a Reset). It should be noted that
the restart sequence depends on the original state
of the MCU (normal, interrupt or non-maskable in-
terrupt mode) prior to entering WAIT or STOP
mode, as well as on the interrupt type.
– In the event of a non-maskable interrupt, the
non-maskable interrupt service routine is proc-
essed first, then the routine in which the WAIT or
STOP mode was entered will be completed by
executing the instruction following the STOP or
WAIT instruction. The MCU remains in normal
interrupt mode.
Interrupts do not affect the oscillator selection.
3.5.3.1 Normal Mode
If the MCU was in the main routine when the WAIT
or STOP instruction was executed, exit from Stop
or Wait mode will occur as soon as an interrupt oc-
curs; the related interrupt routine is executed and,
on completion, the instruction which follows the
STOP or WAIT instruction is then executed, pro-
viding no other interrupts are pending.
Notes:
To achieve the lowest power consumption during
RUN or WAIT modes, the user program must take
care of:
– configuring unused I/Os as inputs without pull-up
(these should be externally tied to well defined
logic levels);
3.5.3.2 Non Maskable Interrupt Mode
If the STOP or WAIT instruction has been execut-
ed during execution of the non-maskable interrupt
routine, the MCU exits from the Stop or Wait mode
as soon as an interrupt occurs: the instruction
which follows the STOP or WAIT instruction is ex-
ecuted, and the MCU remains in non-maskable in-
terrupt mode, even if another interrupt has been
generated.
– placing all peripherals in their power down
modes before entering STOP mode;
When the hardware activated Watchdog is select-
ed, or when the software Watchdog is enabled, the
STOP instruction is disabled and a WAIT instruc-
tion will be executed in its place.
3.5.3.3 Normal Interrupt Mode
If all interrupt sources are disabled (GEN low), the
MCU can only be restarted by a Reset. Although
setting GEN low does not mask the NMI as an in-
terrupt, it will stop it generating a wake-up signal.
If the MCU was in interrupt mode before the STOP
or WAIT instruction was executed, it exits from
STOP or WAIT mode as soon as an interrupt oc-
curs. Nevertheless, two cases must be consid-
ered:
The WAIT and STOP instructions are not execut-
ed if an enabled interrupt request is pending.
– If the interrupt is a normal one, the interrupt rou-
tine in which the WAIT or STOP mode was en-
32/74
32
ST62T40B/E40B
4 ON-CHIP PERIPHERALS
4.1 I/O PORTS
The MCU features Input/Output lines which may
be individually programmed as any of the following
input or output configurations:
be also written by user software, in conjunction
with the related option registers, to select the dif-
ferent input mode options.
– Input without pull-up or interrupt
– Input with pull-up and interrupt
– Input with pull-up, but without interrupt
– Analog input
Single-bit operations on I/O registers are possible
but care is necessary because reading in input
mode is done from I/O pins while writing will direct-
ly affect the Port data register causing an unde-
sired change of the input configuration.
The Data Direction registers (DDRx) allow the
data direction (input or output) of each pin to be
set.
– Push-pull output
– Open drain output
The lines are organised as bytewise Ports.
The Option registers (ORx) are used to select the
different port options available both in input and in
output mode.
Each port is associated with 3 registers in Data
space. Each bit of these registers is associated
with a particular line (for instance, bits 0 of Port A
Data, Direction and Option registers are associat-
ed with the PA0 line of Port A).
All I/O registers can be read or written to just as
any other RAM location in Data space, so no extra
RAM cells are needed for port data storage and
manipulation. During MCU initialization, all I/O reg-
isters are cleared and the input mode with pull-ups
and no interrupt generation is selected for all the
pins, thus avoiding pin conflicts.
The DATA registers (DRx), are used to read the
voltage level values of the lines which have been
configured as inputs, or to write the logic value of
the signal to be output on the lines configured as
outputs. The port data registers can be read to get
the effective logic levels of the pins, but they can
Figure 18. I/O Port Block Diagram
RESET
V
DD
S
CONTROLS
IN
DATA
DIRECTION
REGISTER
V
DD
INPUT/OUTPUT
DATA
REGISTER
SHIFT
REGISTER
OPTION
REGISTER
S
OUT
TO INTERRUPT
TO ADC
VA00413
33/74
33
ST62T40B/E40B
I/O PORTS (Cont’d)
4.1.1 Operating Modes
4.1.1.2 Interrupt Options
Each pin may be individually programmed as input
or output with various configurations.
All input lines can be individually connected by
software to the interrupt system by programming
the OR and DR registers accordingly. The inter-
rupt trigger modes (falling edge, rising edge and
low level) can be configured by software as de-
scribed in the Interrupt Chapter for each port.
This is achieved by writing the relevant bit in the
Data (DR), Data Direction (DDR) and Option reg-
isters (OR). Table 13 illustrates the various port
configurations which can be selected by user soft-
ware.
4.1.1.3 Analog Input Options
4.1.1.1 Input Options
Some pins can be configured as analog inputs by
programming the OR and DR registers according-
ly. These analog inputs are connected to the on-
chip 8-bit Analog to Digital Converter. ONLY ONE
pin should be programmed as an analog input at
any time, since by selecting more than one input
simultaneously their pins will be effectively short-
ed.
Pull-up, High Impedance Option. All input lines
can be individually programmed with or without an
internal pull-up by programming the OR and DR
registers accordingly. If the pull-up option is not
selected, the input pin will be in the high-imped-
ance state.
Table 13. I/O Port Option Selection
DDR
OR
0
DR
0
Mode
Input
Option
0
0
0
0
1
1
With pull-up, no interrupt
0
1
Input
No pull-up, no interrupt
1
0
Input
With pull-up and with interrupt
1
1
Input
Analog input (when available)
0
X
X
Output
Output
Open-drain output (20mA sink when available)
Push-pull output (20mA sink when available)
1
Note: X = Don’t care
34/74
34
ST62T40B/E40B
I/O PORTS (Cont’d)
4.1.2 Safe I/O State Switching Sequence
outputs, it is advisable to keep a copy of the data
register in RAM. Single bit instructions may then
be used on the RAM copy, after which the whole
copy register can be written to the port data regis-
ter:
Switching the I/O ports from one state to another
should be done in a sequence which ensures that
no unwanted side effects can occur. The recom-
mended safe transitions are illustrated in Figure
19. All other transitions are potentially risky and
should be avoided when changing the I/O operat-
ing mode, as it is most likely that undesirable side-
effects will be experienced, such as spurious inter-
rupt generation or two pins shorted together by the
analog multiplexer.
SET bit, datacopy
LD a, datacopy
LD DRA, a
Warning: Care must also be taken to not use in-
structions that act on a whole port register (INC,
DEC, or read operations) when all 8 bits are not
available on the device. Unavailable bits must be
masked by software (AND instruction).
Single bit instructions (SET, RES, INC and DEC)
should be used with great caution on Ports Data
registers, since these instructions make an implicit
read and write back of the entire register. In port
input mode, however, the data register reads from
the input pins directly, and not from the data regis-
ter latches. Since data register information in input
mode is used to set the characteristics of the input
pin (interrupt, pull-up, analog input), these may be
unintentionally reprogrammed depending on the
state of the input pins. As a general rule, it is better
to limit the use of single bit instructions on data
registers to when the whole (8-bit) port is in output
mode. In the case of inputs or of mixed inputs and
The WAIT and STOP instructions allow the
ST62xx to be used in situations where low power
consumption is needed. The lowest power con-
sumption is achieved by configuring I/Os in input
mode with well-defined logic levels.
The user must take care not to switch outputs with
heavy loads during the conversion of one of the
analog inputs in order to avoid any disturbance to
the conversion.
Figure 19. Diagram showing Safe I/O State Transitions
Interrupt
Input
010*
011
001
pull-up
Analog
Input
pull-up (Reset
state)
000
100
Input
Output
Open Drain
Output
Open Drain
101
111
Output
Push-pull
Output
Push-pull
110
Note *. xxx = DDR, OR, DR Bits respectively
35/74
35
ST62T40B/E40B
I/O PORTS (Cont’d)
Table 14. I/O Port configuration for the ST62T40B/E40B
MODE
AVAILABLE ON(1)
SCHEMATIC
PA0-PA7
Input
PB0-PB7
PC0-PC7
Data in
Interrupt
Input
PA0-PA7
PB0-PB7
PC0-PC7
with pull up
Data in
(Reset state except for
PC0-PC7)
Interrupt
Input
PA0-PA7
PB0-PB7
PC0-PC7
with pull up
with interrupt
Data in
Interrupt
PA0-PA7
PB0-PB3
Analog Input
ADC
Open drain output
5mA
PA0-PA7
PB0-PB7
PC0-PC7 (1mA)
Data out
Open drain output
20mA
PB4-PB7
Push-pull output
5mA
PA0-PA7
PB0-PB7
PC0-PC7 (1mA)
Data out
Push-pull output
20mA
PB4-PB7
Note 1. Provided the correct configuration has been selected.
36/74
36
ST62T40B/E40B
I/O PORTS (Cont’d)
4.1.3 LCD alternate functions (combiports)
4.1.4 SPI alternate functions
PC0 to PC7 can also be individually defined as 8
LCD segment output by setting DDRC, ORC and
DRC registers as shown in Table 15.
PB6/Sin and PB5/Scl pins must be configured as
input through the DDR and OR registers to be
used data in and data clock (Slave mode) for the
SPI. All input modes are available and I/O’s can be
read independantly of the SPI at any time.
On the contrary with other I/O lines, the reset state
is the LCD output mode. These 8 segment lines are
recognised as S33..S40 by the embedded LCD
controller drive.
PB7/Sout must be configured in open drain output
mode to be used as data out for the SPI. In output
mode, the value present on the pin is the port data
register content only if PB7 is defined as push pull
output, while serial transmission is possible only in
open drain mode.
Table 15. PC0-PC7 Combiport Option Selection
DDR
OR
0
DR
0
Mode
Input
Option
0
0
0
0
1
1
With pull-up, no interrupt
0
1
Input
No pull-up, no interrupt
With pull-up and with interrupt
LCD segment (Reset state)
Open-drain output
1
0
Input
1
1
Input
0
X
X
Output
Output
1
Push-pull output
Note: X = Don’t care
Figure 20. Peripheral Interface Configuration of SPI
PID
PP/OD
OPR
DR
1
0
PB7/Sout
PB6/Sin
PB5/Scl
MUX
OUT
IN
PID
PID
DR
SYNCHRONOUS
SERIAL I/O
CLOCK
DR
VR01661F
37/74
37
ST62T40B/E40B
I/O PORTS (Cont’d)
4.1.5 I/O Port Option Registers
4.1.7 I/O Port Data Registers
ORA/B/C (CCh PA, CEh PB, CFh PC)
Read/Write
DRA/B/C (C0h PA, C1h PB, C3h PC)
Read/Write
7
0
7
0
Px7 Px6 Px5 Px4 Px3 Px2 Px1 Px0
Px7 Px6 Px5 Px4 Px3 Px2 Px1 Px0
Bit 7-0 = Px7 - Px0: Port A, B, C Option Register
bits.
Bit 7-0 = Px7 - Px0: Port A, B, C Data Registers
bits.
4.1.6 I/O Port Data Direction Registers
DDRA/B/C (C4h PA, C5h PB, C6h PC)
Read/Write
7
0
Px7 Px6 Px5 Px4 Px3 Px2 Px1 Px0
Bit 7-0 = Px7 - Px0: Port A, B, C Data Direction
Registers bits.
38/74
38
ST62T40B/E40B
4.2 TIMER 1 & 2
The MCU features two on-chip Timer peripheral
named TIMER 1 & TIMER 2. Each of these timers
consist of an 8-bit counter with a 7-bit programma-
The prescaler input can be either the internal fre-
quency f
divided by 12 (TIMER 1 & 2) or an ex-
INT
ternal clock applied to the TIMER pin (TIMER 1).
The prescaler decrements on the rising edge. De-
pending on the division factor programmed by
PS2, PS1 and PS0 bits in the TSCR. The clock in-
put of the timer/counter register is multiplexed to
different sources. For division factor 1, the clock
input of the prescaler is also that of timer/counter;
for factor 2, bit 0 of the prescaler register is con-
nected to the clock input of TCR. This bit changes
its state at half the frequency of the prescaler input
clock. For factor 4, bit 1 of the PSC is connected to
the clock input of TCR, and so forth. The prescaler
initialize bit, PSI, in the TSCR register must be set
to “1” to allow the prescaler (and hence the coun-
ter) to start. If it is cleared to “0”, all the prescaler
bits are set to “1” and the counter is inhibited from
counting. The prescaler can be loaded with any
value between 0 and 7Fh, if bit PSI is set to “1”.
The prescaler tap is selected by means of the
PS2/PS1/PS0 bits in the control register.
15
ble prescaler, giving a maximum count of 2 .
Figure 22 and Figure 23 show the Timer Block Di-
agrams. An external TIMER pin is available to the
user on the TIMER 1 allowing external control of
the counting clock or signal generation.
The content of the 8-bit counter can be read/writ-
ten in the Timer/Counter register, TCR, while the
state of the 7-bit prescaler can be read in the PSC
register. The control logic device is managed in
the TSCR register as described in the following
paragraphs.
The 8-bit counter is decremented by the output
(rising edge) coming from the 7-bit prescaler and
can be loaded and read under program control.
When it decrements to zero then the TMZ (Timer
Zero) bit in the TSCR is set to “1”. If the ETI (Ena-
ble Timer Interrupt) bit in the TSCR is also set to
“1”, an interrupt request is generated as described
in the Interrupt Chapter. The Timer interrupt can
be used to exit the MCU from WAIT mode.
Figure 21 illustrates the Timer’s working principle.
Figure 21. Timer Working Principle
7-BIT PRESCALER
BIT3
BIT0
BIT1
BIT2
BIT4
BIT5
BIT6
CLOCK
PS0
PS1
PS2
0
1
2
4
7
3
5
6
8-1 MULTIPLEXER
BIT7
BIT0
BIT1
BIT2
BIT3
BIT4
BIT5
BIT6
8-BIT COUNTER
VA00186
39/74
39
ST62T40B/E40B
Figure 22. TIMER 1 Block Diagram
DATABUS 8
8
8
8
6
5
4
3
2
b5
b1
b0
b7
b6
b4
b3
b2
8-BIT
COUNTER
STATUS/CONTROL
REGISTER
SELECT
OF 8
PSC
1
TMZ ETI TOUT
PSI
PS1
PS0
DOUT
PS2
1
0
3
TIMER
INTERRUPT
LINE
LATCH
SYNCHRONIZATION
LOGIC
VA00009
Figure 23. TIMER 2 Block Diagram
DATA BUS
8
8
8
6
5
4
3
2
1
0
8-BIT
COUNTER
b7 b6 b5
b4 b3 b2 b1 b0
STATUS/CONTROL
REGISTER
SELECT
1 OF 7
PSC
f
TMZ ETI D5
D4 PSI PS2 PS1 PS0
INT
12
3
INTERRUPT
LINE
VR02070A
40/74
40
ST62T40B/E40B
TIMER 1& 2 (Cont’d)
4.2.1 TIMER 1 Operating Modes
4.2.2 TIMER 2 Operating Mode
The Timer prescaler is clocked by the prescaler
clock input (f ÷ 12).
There are three operating modes, which are se-
lected by the TOUT and DOUT bits (see TSCR
register). These three modes correspond to the
two clocks which can be connected to the 7-bit
INT
The user can select the desired prescaler division
ratio through the PS2, PS1, PS0 bits. When the
TCR count reaches 0, it sets the TMZ bit in the
TSCR. The TMZ bit can be tested under program
control to perform a timer function whenever it
goes high.
prescaler (f
the output mode.
÷ 12 or TIMER pin signal), and to
INT
4.2.1.1 Gated Mode
(TOUT = “0”, DOUT = “1”)
4.2.3 Timer Interrupt
In this mode the prescaler is decremented by the
Timer clock input (f
÷ 12), but ONLY when the
When one of the counter registers decrements to
zero with the associated ETI (Enable Timer Inter-
rupt) bit set to one, an interrupt request is generat-
ed as described in Interrupt Chapter. When the
counter decrements to zero, the associated TMZ
bit in the TSCR register is set to one.
INT
signal on the TIMER pin is held high (allowing
pulse width measurement). This mode is selected
by clearing the TOUT bit in the TSCR register to
“0” (i.e. as input) and setting the DOUT bit to “1”.
4.2.1.2 Event Counter Mode
4.2.4 Application Notes
(TOUT = “0”, DOUT = “0”)
The user can select the presence of an on-chip
pull-up on the TIMER pin as option.
In this mode, the TIMER pin is an input and the
prescaler is decremented on the rising edge.
TMZ is set when the counter reaches zero; howev-
er, it may also be set by writing 00h in the TCR
register or by setting bit 7 of the TSCR register.
The TMZ bit must be cleared by user software
when servicing the timer interrupt to avoid unde-
sired interrupts when leaving the interrupt service
routine. After reset, the 8-bit counter register is
loaded with 0FFh, while the 7-bit prescaler is load-
ed with 07Fh, and the TSCR register is cleared.
This means that the Timer is stopped (PSI=“0”)
and the timer interrupt is disabled.
4.2.1.3 Output Mode
(TOUT = “1”, DOUT = data out)
The TIMER pin is connected to the DOUT latch,
hence the Timer prescaler is clocked by the pres-
caler clock input (f
÷ 12).
INT
The user can select the desired prescaler division
ratio through the PS2, PS1, PS0 bits. When the
TCR count reaches 0, it sets the TMZ bit in the
TSCR. The TMZ bit can be tested under program
control to perform a timer function whenever it
goes high. The low-to-high TMZ bit transition is
used to latch the DOUT bit of the TSCR and trans-
fer it to the TIMER pin. This operating mode allows
external signal generation on the TIMER pin.
A write to the TCR register will predominate over
the 8-bit counter decrement to 00h function, i.e. if a
write and a TCR register decrement to 00h occur
simultaneously, the write will take precedence,
and the TMZ bit is not set until the 8-bit counter
reaches 00h again. The values of the TCR and the
PSC registers can be read accurately at any time.
Table 16. Timer Operating Modes
TOUT
DOUT
Timer Pin
Input
Timer Function
Event Counter
Gated Input
Output “0”
0
0
1
1
0
1
0
1
Input
Output
Output
Output “1”
41/74
41
ST62T40B/E40B
TIMER 1& 2 (Cont’d)
4.2.5 TIMER 1 Registers
Bit 2, 1, 0 = PS2, PS1, PS0: Prescaler Mux. Se-
lect. These bits select the division ratio of the pres-
caler register.
Timer Status Control Register (TSCR)
Address: 0D4h
—
Read/Write
Table 17. Prescaler Division Factors
7
0
PS2
0
PS1
0
PS0
0
Divided by
TMZ
ETI
TOUT DOUT PSI
PS2
PS1
PS0
1
2
0
0
1
Bit 7 = TMZ: Timer Zero bit
0
1
0
4
0
1
1
8
A low-to-high transition indicates that the timer
count register has decrement to zero. This bit
must be cleared by user software before starting a
new count.
1
0
0
16
32
64
128
1
0
1
1
1
0
Bit 6 = ETI: Enable Timer Interrup
1
1
1
When set, enables the timer interrupt request. If
ETI=0 the timer interrupt is disabled. If ETI=1 and
TMZ=1 an interrupt request is generated.
Timer Counter Register (TCR)
Address: 0D3h
— Read/Write
Bit 5 = TOUT: Timer Output Control.
7
0
When low, this bit select the input mode for the
TIMER pin. when high the output mode is select-
ed.
D7
D6
D5
D4
D3
D2
D1
D0
Bit 4 = DOUT: Data Ouput
Bit 7-0 = D7-D0: Counter Bits.
Data sent to the timer output when TMZ is set high
(output mode only). Input mode selection (input
mode only)
Prescaler Register PSC
Bit 3 = PSI: Prescaler Initialize Bit
Address: 0D2h
— Read/Write
Used to initialize the prescaler and inhibit its count-
ing. When PSI=“0” the prescaler is set to 7Fh and
the counter is inhibited. When PSI=“1” the prescal-
er is enabled to count downwards. As long as
PSI=“0” both counter and prescaler are not run-
ning.
7
0
D7
D6
D5
D4
D3
D2
D1
D0
Bit 7 = D7: Always read as ”0”.
Bit 6-0 = D6-D0: Prescaler Bits.
42/74
42
ST62T40B/E40B
TIMER 1& 2 (Cont’d)
4.2.6 TIMER 2 Registers
PS2
0
PS1
0
PS0
0
Divided by
1
2
Timer Status Control Register (TSCR)
0
0
1
Address: 0D7h
—
Read/Write
0
1
0
4
7
0
0
1
1
8
1
0
0
16
32
64
128
TMZ
ETI
D5
D4
PSI
PS2
PS1
PS0
1
0
1
1
1
0
Bit 7 = TMZ: Timer Zero bit
1
1
1
A low-to-high transition indicates that the timer
count register has decrement to zero. This bit
must be cleared by user software before starting a
new count.
Timer Counter Register (TCR)
Address: 0D6h
— Read/Write
Bit 6 = ETI: Enable Timer Interrup
When set, enables the timer interrupt request. If
ETI=0 the timer interrupt is disabled. If ETI=1 and
TMZ=1 an interrupt request is generated.
7
0
D7
D6
D5
D4
D3
D2
D1
D0
Bit 5 = D5: Reserved
Must be set to “1”.
Bit 4 = D4
Bit 7-0 = D7-D0: Counter Bits.
Prescaler Register PSC
Do not care.
Address: 0D5h
— Read/Write
Bit 3 = PSI: Prescaler Initialize Bit
Used to initialize the prescaler and inhibit its count-
ing. When PSI=“0” the prescaler is set to 7Fh and
the counter is inhibited. When PSI=“1” the prescal-
er is enabled to count downwards. As long as
PSI=“0” both counter and prescaler are not run-
ning.
7
0
D7
D6
D5
D4
D3
D2
D1
D0
Bit 7 = D7: Always read as ”0”.
Bit 6-0 = D6-D0: Prescaler Bits.
Bit 2, 1, 0 = PS2, PS1, PS0: Prescaler Mux. Se-
lect. These bits select the division ratio of the pres-
caler register.
43/74
43
ST62T40B/E40B
4.3 A/D CONVERTER (ADC)
The A/D converter peripheral is an 8-bit analog to
digital converter with analog inputs as alternate I/O
functions (the number of which is device depend-
ent), offering 8-bit resolution with a typical conver-
sion time of 70us (at an oscillator clock frequency
of 8MHz).
sion to allow stabilisation of the A/D converter.
This action is also needed before entering WAIT
mode, since the A/D comparator is not automati-
cally disabled in WAIT mode.
During Reset, any conversion in progress is
stopped, thecontrol register is reset to 40h and the
ADC interrupt is masked (EAI=0).
The ADC converts the input voltage by a process
of successive approximations, using a clock fre-
quency derived from the oscillator with a division
factor of twelve. With an oscillator clock frequency
less than 1.2MHz, conversion accuracy is de-
creased.
Figure 24. ADC Block Diagram
INTERRUPT
CLOCK
Selection of the input pin is done by configuring
the related I/O line as an analog input via the Op-
tion and Data registers (refer to I/O ports descrip-
tion for additional information). Only one I/O line
must be configured as an analog input at any time.
The user must avoid any situation in which more
than one I/O pin is selected as an analog input si-
multaneously, to avoid device malfunction.
Ain
CONVERTER
RESET
AV
AV
SS
DD
CONTROL REGISTER
8
RESULT REGISTER
8
The ADC uses two registers in the data space: the
ADC data conversion register, ADR, which stores
the conversion result, and the ADC control regis-
ter, ADCR, used to program the ADC functions.
CORE
CORE
CONTROL SIGNALS
VA00418
A conversion is started by writing a “1” to the Start
bit (STA) in the ADC control register. This auto-
matically clears (resets to “0”) the End Of Conver-
sion Bit (EOC). When a conversion is complete,
the EOC bit is automatically set to “1”, in order to
flag that conversion is complete and that the data
in the ADC data conversion register is valid. Each
conversion has to be separately initiated by writing
to the STA bit.
4.3.1 Application Notes
The A/D converter does not feature a sample and
hold circuit. The analog voltage to be measured
should therefore be stable during the entire con-
version cycle. Voltage variation should not exceed
±1/2 LSB for the optimum conversion accuracy. A
low pass filter may be used at the analog input
pins to reduce input voltage variation during con-
version.
The STA bit is continuously scanned so that, if the
user sets it to “1” while a previous conversion is in
progress, a new conversion is started before com-
pleting the previous one. The start bit (STA) is a
write only bit, any attempt to read it will show a log-
ical “0”.
When selected as an analog channel, the input pin
is internally connected to a capacitor C of typi-
ad
cally 12pF. For maximum accuracy, this capacitor
must be fully charged at the beginning of conver-
sion. In the worst case, conversion starts one in-
struction (6.5 µs) after the channel has been se-
lected. In worst case conditions, the impedance,
ASI, of the analog voltage source is calculated us-
ing the following formula:
The A/D converter features a maskable interrupt
associated with the end of conversion. This inter-
rupt is associated with interrupt vector #4 and oc-
curs when the EOC bit is set (i.e. when a conver-
sion is completed). The interrupt is masked using
the EAI (interrupt mask) bit in the control register.
6.5µs = 9 x C x ASI
ad
(capacitor charged to over 99.9%), i.e. 30 kΩ in-
cluding a 50% guardband. ASI can be higher if C
has been charged for a longer period by adding in-
structions before the start of conversion (adding
more than 26 CPU cycles is pointless).
The power consumption of the device can be re-
duced by turning off the ADC peripheral. This is
done by setting the PDS bit in the ADC control reg-
ister to “0”. If PDS=“1”, the A/D is powered and en-
abled for conversion. This bit must be set at least
one instruction before the beginning of the conver-
ad
44/74
44
ST62T40B/E40B
A/D CONVERTER (Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
A/D Converter Control Register (ADCR)
The accuracy of the conversion depends on the
Address: 0D1h
— Read/Write
quality of the power supplies (V
and V ). The
DD
SS
user must take special care to ensure a well regu-
lated reference voltage is present on the V and
7
0
DD
EAI
EOC
STA
PDS
D3
D2
D1
D0
V
pins (power supply voltage variations must be
SS
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the V
pin.
DD
Bit 7 = EAI: Enable A/D Interrupt. If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
The converter resolution is given by::
Bit 6 = EOC: End of conversion. Read Only. This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
V
DD – VSS
----------------------------
256
The Input voltage (Ain) which is to be converted
must be constant for 1µs before conversion and
remain constant during conversion.
Bit 5 = STA: Start of Conversion. Write Only. Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
Conversion resolution can be improved if the pow-
er supply voltage (V ) to the microcontroller is
DD
lowered.
In orderto optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
Bit 4 = PDS: Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
Bit 3-0 = D3-D0. Not used
instruction may cause a small variation of the V
DD
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
A/D Converter Data Register (ADR)
Address: 0D0h
— Read only
7
0
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
D7
D6
D5
D4
D3
D2
D1
D0
Bit 7-0 = D7-D0: 8 Bit A/D Conversion Result.
45/74
45
ST62T40B/E40B
4.4 SERIAL PERIPHERAL INTERFACE (SPI)
The on-chip SPI is an optimized serial synchro-
nous interface that supports a wide range of indus-
try standard SPI specifications. The on-chip SPI is
controlled by small and simple user software to
perform serial data exchange. The serial shift
clock can be implemented either by software (us-
ing the bit-set and bit-reset instructions), with the
on-chip Timer 1 by externally connecting the SPI
clock pin to the timer pin or by directly applying an
external clock to the Scl line.
operation Sout has to be programmed as open-
drain output.
The SCL, Sin and Sout SPI clock and data signals
are connected to 3 I/O lines on the same external
pins. With these 3 lines, the SPI can operate in the
following operating modes: Software SPI, S-BUS,
I C-bus and as a standard serial I/O (clock, data,
enable). An interrupt request can be generated af-
ter eight clock pulses. Figure 25 shows the SPI
block diagram.
The peripheral is composed by an 8-bit Data/shift
Register and a 4-bit binary counter while the Sin
pin is the serial shift input and Sout is the serial
shift output. These two lines can be tied together
to implement two wires protocols (I C-bus, etc).
When data is serialized, the MSB is thefirst bit. Sin
has to be programmed as input. For serial output
The SCL line clocks, on the falling edge, the shift
register and the counter. To allow SPI operation in
slave mode, the SCL pin must be programmed as
input and an external clock must be supplied to
this pin to drive the SPI peripheral.
In master mode, SCL is programmed as output, a
clock signal must be generated by software to set
and reset the port line.
Figure 25. SPI Block Diagram
SPI Interrupt Disable Register
Write
SPI Data Register
Read
CLK
RESET
SCL
I/O Port
Data Reg
Direction
Set Res
DIN
Q4
Q4
RESET
4-Bit Counter
CP
(Q4=High after Clock8)
Sin
I/O Port
Data Reg
Direction
Interrupt
Reset
Load
8-Bit Data
Shift Register
CP
DIN
DOUT
Output
Enable
8-Bit Tristate Data I/O
OPR Reg.
Sout
I/O Port
0
1
DOUT
D0.............. ......... .....D7
to Processor Data Bus
Data Reg
Direction
VR01504
46/74
46
ST62T40B/E40B
SERIAL PERIPHERAL INTERFACE (Cont’d)
After 8 clock pulses (D7..D0) the output Q4 of the
4-bit binary counter becomes low, disabling the
clock from the counter and the data/shift register.
Q4 enables the clock to generate an interrupt on
the 8th clock falling edge as long as no reset of the
counter (processor write into the 8-bit data/shift
register) takes place. After a processor reset the
interrupt is disabled. The interrupt is active when
writing data in the shift register and desactivated
when writing any data in the SPI Interrupt Disable
register.
As it is possible to directly read the Sin pin directly
through the port register, the software can detect a
difference between internal data and external data
(master mode). Similar condition can be applied to
the clock.
Three (Four) Wire Serial Bus
It is possible to use a single general purpose I/O
pin (with the corresponding interrupt enabled) as a
chip enable pin. SCL acts as active or passive
clock pin, Sin as data in and Sout as data out (four
wire bus). Sin and Sout can be connected together
externally to implement three wire bus.
The generation of an interrupt to the Core provides
information that new data is available (input mode)
or that transmission is completed (output mode),
allowing the Core to generate an acknowledge on
the 9th clock pulse (I C-bus).
Note:
When the SPI is not used, the three I/O lines (Sin,
SCL, Sout) can be used as normal I/O, with the fol-
lowing limitation: bit Sout cannot be used in open
drain mode as this enables the shift register output
to the port.
The interrupt is initiated by a high to low transition,
and therefore interrupt options must be set accord-
ingly as defined in the interrupt section.
It is recommended, in order to avoid spurious in-
terrupts from the SPI, to disable the SPI interrupt
(the default state after reset) i.e. no write must be
made to the 8-bit shift register. An explicit interrupt
disable may be made in software by a dummy
write to the SPI interrupt disable register.
After power on reset, or after writing the data/shift
register, the counter is reset to zero and the clock
is enabled. In this condition the data shift register
is ready for reception. No start condition has to be
detected. Through the user software the Core may
pull down the Sin line (Acknowledge) and slow
down the SCL, as long as it is needed to carry out
data from the shift register.
SPI Data/Shift Register
Address: DDh - Read/Write (SDSR)
I C-bus Master-Slave, Receiver-Transmitter
7
0
When pins Sin and Sout are externally connected
together it is possible to use the SPI as a receiver
as well as a transmitter. Through software routine
(by using bit-set and bit-reset on I/O line) a clock
can be generated allowing I C-bus to work in mas-
ter mode.
D7
D6
D5
D4
D3
D2
D1
D0
A write into this register enables SPI Interrupt after
8 clock pulses.
When implementing an I C-bus protocol, the start
condition can be detected by setting the processor
into a wait for start condition by enabling the inter-
rupt of the I/O port used for the Sin line. This frees
the processor from polling the Sin and SCL lines.
After the transmission/reception the processor has
to poll for the STOP condition.
SPI Interrupt Disable Register
Address: C2h - Read/Write (SIDR)
7
0
D7
D6
D5
D4
D3
D2
D1
D0
In slave mode the user software can slow down
the SCL clock frequency by simply putting the SCL
I/O line in output open-drain mode and writing a
zero into the corresponding data register bit.
A dummy write to this register disables SPI Inter-
rupt.
47/74
47
ST62T40B/E40B
4.5 LCD CONTROLLER-DRIVER
On-chip LCD driver includes all features required
for LCD driving, including multiplexing of the com-
mon plates. Multiplexing allows to increase display
capability without increasing the number of seg-
ment outputs. In that case, the display capability is
equal to the product of the number of common
plates with the number of segment outputs.
ment and common lines are switched to ground to
avoid any DC biasing of the LCD elements.
Table 19. Oscillator Selection Bits
MCU
Oscillator HF2 HF1 HF0
fOSC
Division Factor
A dedicated LCD RAM is used to store the pattern
to be displayed while control logic generates ac-
cordingly all the waveforms sent onto the segment
or common outputs. Segments voltage supply is
MCU supply independant, and included driving
stages allow direct connection to the LCD panel.
0
0
0
0
0
1
0
1
0
Clock disabled: Display off
Auxiliary 32KHz oscillator
Reserved
1.048MHz
2.097MHz
4.194MHz
8.388MHz
0
1
1
1
0
0
1
0
1
32
64
128
The multiplexing ratio (Number of common plates)
and the base LCD frame frequency is software
configurable to achieve the best trade-off con-
trast/display capability for each display panel.
1
1
1
1
0
1
256
Reserved
Notes:
The 32KHz clock used for the LCD controller is
derivated from the MCU’s internal clock and there-
fore does not require a dedicated oscillator. The
division factor is set by the three bits HF0..HF2 of
the LCD Mode Control Register LCDCR as sum-
marized in Table 19 for recommanded oscillator
quartz values. In case of oscillator failure, all seg-
1. The usage fOSC values different from those
defined in this table cause the LCD to operate at a
reference frequency different from 32.768KHz, ac-
cording to division factor of Table 19.
2. It is not recommended to select an internal
frequency lower than 32KHz as the clock supervi-
sor circuit may switch off the LCD peripheral if low-
er frequency is detected.
Figure 26. LCD Block Diagram
1/3
2/3
SEGMENTS
BACKPLANES
VLCD VLCD VLCD
VOLTAGE
DIVIDER
COMMON
DRIVER
SEGMENT
DRIVER
LCD
RAM
CONTROLLER
32KHz
CONTROL
REGISTER
f
int
CLOCK
SELECTION
OSC 32KHz
(When available)
DATA BUS
VR02099
48/74
48
ST62T40B/E40B
LCD CONTROLLER-DRIVER (Continued)
4.5.1 Multiplexing ratio and frame frequency
setting
nal connection of the 1/3VLCD and 2/3VLCD pins
(Figure 27).
Up to 4 common plates COM1..COM4 can be
used for multiplexing ratio ranging from 1/1 to 1/4.
The selection is made by the bits DS0 and DS1 of
the LCDCR as shown in the Table 20.
Figure 27. Bias Config for 1/2 Duty
LCDOFF
Table 20. Multiplexing ratio
V
V
LCD
DS1 DS0
Display Mode
1/4 mux.ratio
1/1 mux.ratio
1/2 mux.ratio
1/3 mux.ratio
Active backplanes
COM1, 2, 3, 4
COM1
0
0
1
1
0
1
0
1
R
R
R
H
H
H
LCD2/3
COM1, 2
COM1, 2, 3
If the 1/1 multiplexing ratio is chosen, LCD seg-
ments are refreshed with a frame frequency Flcd
derived from 32KHz clock with a division ratio de-
fined by the bits LF0..LF2 of the LCDCR.
V
LCD1/3
V
SS
When ahigher multiplexing ratiois set,refreshment
frequency is decreased accordingly (Table 21).
Table 21. LCD Frame Frequency Selection
Frame Frequency f (Hz)
F
Base
VR01367
1/1
1/2
1/3
1/4
f
LF2
LF1
LF0
LCD
mux. mux. mux. mux.
ratio ratio ratio ratio
(Hz)
Figure 28. Typical Current consumption on
VLCD Pin(25°C, noload,fLCD=512Hz, mux=1/3-
1/4)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
64
85
64
85
32
43
64
85
21
28
43
57
85
16
21
32
43
64
85
128 128
171 171
I
(µA)
LCD
256 256 128
70
60
341 341 171 114
512 512 256 171 128
Reserved
50
40
30
20
10
4.5.2 Segment and common plates driving
LCD panels physical structure requires precise
timings and stepped voltage values on common
and segment outputs. Timings are managed by
the LCD controller, while voltages are derivated
from the VLCD value through internal resistive di-
vision. This internal divider is disabled when the
LCD driver is OFF in order to avoid consumption
on VLCD pin.
3
4
5
6
7
8
9
10
V
(V)
LCD
VR01838
The 1/3 VLCD and 2/3 VLCD values used in 1/1,
1/3 and 1/4 multiplexing ratio modes are internally
generated and issued on external pins, while 1/2
VLCD value used in 1/2 mode is obtained by exter-
Note: For display voltages V
< 4.5V the resis-
LCD
tivity of the divider may be too high for some appli-
cations (especially using 1/3 or 1/4 duty display
mode). In that case an external resistive divider
must be used to achieve the desired resistivity.
49/74
49
ST62T40B/E40B
LCD CONTROLLER-DRIVER (Continued)
Figure 29. Typical Network to connect to V
Typical External resistances values are in the
range of 100 KΩ to 150 KΩ. External capacitances
LCD
pins if V
≤ 4.5V
LCD
in the range of 10 to 47 nF can be added to V
LCD
2/3 and V
1/3 pins and to V
if the V
con-
LCD
LCD
LCD
nection is highly impedant.
V
LCD
4.5.3 LCD RAM
R
R
R
LCD RAM is organised as a LCD panel with a ma-
trix architecture. Each bit of its content is logically
mapped to a physical element of the display panel
addressed by a couple (Segment;Common). If a
bit is set, the relevant element of the LCD matrix is
turned-on. On the contrary, an element remains
turned-off as long the associated bit within the
LCD RAM is kept cleared.
V
LCD2/3
LCD1/3
C
C
V
V
After a reset, the LCD RAM is not initialised and
contain arbitrary information.
SS
If the choosen multiplexing ratio does not use
some common plates, corresponding RAM ad-
dresses are free for general purpose data storage.
R: 100kΩ
C: 47nF
VR01840
Figure 30. Addressing Map of the LCD RAM
RAM Address
MSB
S8
LSB
E0
E1
E2
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
S7
S6
S5
S4
NA
NA
NA
S16
S24
S32
S40
S48
S8
S15
S23
S31
S39
S47
S7
S14
S22
S30
S38
S46
S6
S13
S21
S29
S37
S45
S5
S12
S20
S28
S36
S44
S4
S11
S19
S27
S35
S43
NA
S10
S18
S26
S34
S42
NA
S9
S17
S25
S33
S41
NA
COM1
COM2
COM3
COM4
S16
S24
S32
S40
S48
S8
S15
S23
S31
S39
S47
S7
S14
S22
S30
S38
S46
S6
S13
S21
S29
S37
S45
S5
S12
S20
S28
S36
S44
S4
S11
S19
S27
S35
S43
NA
S10
S18
S26
S34
S42
NA
S9
S17
S25
S33
S41
NA
S16
S24
S32
S40
S48
S8
S15
S23
S31
S39
S47
S7
S14
S22
S30
S38
S46
S6
S13
S21
S29
S37
S45
S5
S12
S20
S28
S36
S44
S4
S11
S19
S27
S35
S43
NA
S10
S18
S26
S34
S42
NA
S9
S17
S25
S33
S41
NA
S16
S24
S32
S40
S48
S15
S23
S31
S39
S47
S14
S22
S30
S38
S46
S13
S21
S29
S37
S45
S12
S20
S28
S36
S44
S11
S19
S27
S35
S43
S10
S18
S26
S34
S42
S9
S17
S25
S33
S41
50/74
50
ST62T40B/E40B
LCD CONTROLLER-DRIVER (Continued)
4.5.4 Stand by or STOP operation mode
4.5.5 LCD Mode Control Register (LCDCR)
No clock from the main oscillator is available in
STOP mode for the LCD controller, and the con-
troller is switched off when the STOP instruction is
executed. All segment and common lines are then
switched to ground to avoid any DC biasing of the
LCD elements.
Address: DCh - Read/Write
7
0
DS1
DS0
HF2
HF1
HF0
LF2
LF1
LF0
Bits 7-6 = DS0, DS1. Multiplexing ratio select bits.
These bits select the number of common back-
planes used by the LCD control.
Operation in STOP mode remain possible by
switching to the OSC32KHz, by setting the
HF0..HF2 bit of LCDCR accordingly (Table 19).
Care must be taken for the oscillator switching that
LCD function change is only effective at the end of
a frame. Therefore it must be guaranteed that
enough clock pulses are delivered before entering
into STOP mode. Otherwise the LCD function is
switched off at STOP instruction execution.
Bits 5-3 = HF0, HF1, HF2. Oscillator select bits.
These bits allow the LCD controller to be supplied
with the correct frequency when different high
main oscillator frequencies are selected as system
clock. Table 19 shows the set-up for different clock
crystals.
Bits 2-0 = LF0, LF1, LF2. Base frame frequency
select bits. These bits control the LCD base oper-
ational frequency of the LCD common lines.
51/74
51
ST62T40B/E40B
4.6 POWERSUPPLY SUPERVISOR DEVICE (PSS)
The Power Supply Supervisor device, described in
the Figure 32, permits supervising the crossing of
the PSS pin voltage (VPSS) through a program-
Figure 31. PSS Device Operating Modes
Description
mable voltage (mxV /n), where n and m can be
DD
chosen by software. This device includes:
VPSS
– Aninternal comparator which is connected to the
internal INT line to make an interrupt request to
the Core.
nxVPSS/13
(m+1)x/V /13
DD
– 2resistive voltagedividers that are, respectively,
mx/V /13
DD
supplied by the PSS pin and the V pin. These
DD
two voltage dividers are both connected to the
two inputs of the internal comparator. They con-
sist of 13 identical resistors. It is possible to se-
lect by software 5 voltage rates on the PSS
divider (nxVPSS/13) and 4 voltage rates on the
t
PIF
V
divider(mxV /13). The nand m values can
DD
DD
be chosen by software. These two voltage divid-
ers are disconnected in STOP mode, and when
the PSS device is OFF.
1
0
– An internal device that allows the detection with
t
an hysteresis of V /13.
DD
VR02044A
The PSS device is supplied by an internal connec-
tion to V
supply. The following paragraphs de-
DD
scribe the operating mode of the PSS device and
the PSS register that permits control over the PSS
device. The PSS device is switched off as soon as
the Core executes the STOP instruction, but con-
tinues to work in the WAIT mode.
Figure 32. PSS Device Block Diagram
2k Ω (UP to 13 STEPS)
PSS
PSS ON
+
-
INTERRUPT LINE
SYNCHRO
PIF
SEQUENCER
& LOGIC
V
DD
2k Ω (UP to 13 STEPS)
VA0060
52/74
52
ST62T40B/E40B
POWER SUPPLY SUPERVISOR (Continued)
4.6.1 PSS Operating Mode Description
The resistive voltage divider connected to the PSS
pin provides the internal comparator with the
0.5V < nxV
/13 at detection < V -2V
PSS DD
0.5V < mxV /13 at detection < V -2V
DD
DD
nxV
/13 voltage. The resistive voltage divider
PSS
we must also have:
connected to the V
pin provides the internal
DD
DD
comparator with the mxV /13 voltage. The n and
m
n
m values are selected with the PSS register. It
must be observed that the n and m values must be
selected, taking into consideration the following
electrical constraints:
V
≤ V
≤ V
PSS DD
DD
---
The PIF bit is the interrupt request flag of the PSS
device. This bit follows PSS comparator output.
Figure 33. Typical application using the PSS
V
IN
L48xx
V
DD
P
SS
V
SS
VR01837
53/74
53
ST62T40B/E40B
POWER SUPPLY SUPERVISOR (Continued)
4.6.2 PSS Register
Table 22. V Voltage division rate selection
DD
bits
The PSS register permits control over the PSS de-
vice. The register can be addressed in the data
space as a RAM location at DAh. This register is
cleared after Reset.
PDV1 PDV0
mxV /13
DD
(m+ 1) xV /13
DD
0
0
1
1
0
1
0
1
3xV /13
4xV /13
DD
DD
5xV /13
6xV /13
DD
DD
PSS Status Control Register (PSSCR)
6xV /13
DD
7xV /13
DD
Address: DAh - Read/Write
7xV /13
DD
8xV /13
DD
7
0
Bits 3-1 = PDR2, PDR1, PDR0. Division rate se-
lection bit. The PDR2/1/0 bits are used to inhibit
the PSS device and to select the division rate of
PDV1 PDV0 PDR2 PDR1 PDR0
PSS PSS PSS PSS PSS
PIF
PEI
D0
the PSS voltage (nxV
/13).
PSS
Bit 7 = PIF. Interrupt flag bit. This bit is the interrupt
flag. This bit is set (resp. cleared) as soon as the
Bit 0 = D0. The PSS comparator output is valid 8
cycle times after the programming of the PDR2/1/0
bits. It is forced to zero in the meantime.
equality between nxV
and mxV /13 (resp.
PSS
DD
(m+1)xV /13) occurs.
DD
Bit 6 = PEI. Interrupt mask bit. This bit is the au-
thorization bit of the interrupt request: – If PEI is
set, the interrupt request can reach the Core. – If
PEI is cleared, the interrupt request cannot reach
the Core.
Table23.P Voltagedivisionrate selectionbits
SS
PDR2
PDR1 PDR0 PSS State
nxV /13
PSS
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
IDLE
BUSY
BUSY
BUSY
BUSY
BUSY
4xV
/13
PSS
PSS
PSS
PSS
Bits 5-4 = PDV1, PDV0. Division rate selection bit.
The PDV1/0 bits are used to select the rate of divi-
5xV
6xV
7xV
V
/13
/13
/13
sion of the
V
voltage (mxV /13 or
DD
DD
(m+1)xV /13, according to the hysteresis).
DD
PSS
54/74
54
ST62T40B/E40B
5 SOFTWARE
5.1 ST6 ARCHITECTURE
The ST6 software has been designed to fully use
the hardware in the most efficient way possible
while keeping byte usage to a minimum; in short,
to provide byte efficient programming capability.
The ST6 core has the ability to set or clear any
register or RAM location bit of the Data space with
a single instruction. Furthermore, the program
may branch to a selected address depending on
the status of any bit of the Data space. The carry
bit is stored with the value of the bit when the SET
or RES instruction is processed.
bits of the opcode with the byte following the op-
code. The instructions (JP, CALL) which use the
extended addressing mode are able to branch to
any address of the 4K bytes Program space.
An extended addressing mode instruction is two-
byte long.
Program Counter Relative. The relative address-
ing mode is only used in conditional branch in-
structions. The instruction is used to perform a test
and, if the condition is true, a branch with a span of
-15 to +16 locations around the address of the rel-
ative instruction. If the condition is not true, the in-
struction which follows the relative instruction is
executed. The relative addressing mode instruc-
tion is one-byte long. The opcode is obtained in
adding the three most significant bits which char-
acterize the kind of the test, one bit which deter-
mines whether the branch is a forward (when it is
0) or backward (when it is 1) branch and the four
less significant bits which give the span of the
branch (0h to Fh) which must be added or sub-
tracted to the address of the relative instruction to
obtain the address of the branch.
5.2 ADDRESSING MODES
The ST6 core offers nine addressing modes,
which are described in the following paragraphs.
Three different address spaces are available: Pro-
gram space, Data space, and Stack space. Pro-
gram space contains the instructions which are to
be executed, plus the data for immediate mode in-
structions. Data space contains the Accumulator,
the X,Y,V and W registers, peripheral and In-
put/Output registers, the RAM locations and Data
ROM locations (for storage of tables and con-
stants). Stack space contains six 12-bit RAM cells
used to stack the return addresses for subroutines
and interrupts.
Bit Direct. In the bit direct addressing mode, the
bit to be set or cleared is part of the opcode, and
the byte following the opcode points to the ad-
dress of the byte in which the specified bit must be
set or cleared. Thus, any bit in the 256 locations of
Data space memory can be set or cleared.
Immediate. In the immediate addressing mode,
the operand of the instruction follows the opcode
location. Asthe operand is a ROM byte, the imme-
diate addressing mode is used to access con-
stants which do not change during program execu-
tion (e.g., a constant used to initialize a loop coun-
ter).
Bit Test & Branch. The bit test and branch ad-
dressing mode is a combination of direct address-
ing and relative addressing. The bit test and
branch instruction is three-byte long. The bit iden-
tification and the tested condition are included in
the opcode byte. The address of the byte to be
tested follows immediately the opcode in the Pro-
gram space. The third byte is the jump displace-
ment, which is in the range of -127 to +128. This
displacement can be determined using a label,
which is converted by the assembler.
Direct. In the direct addressing mode, the address
of the byte which is processed by the instruction is
stored in the location which follows the opcode. Di-
rect addressing allows the user to directly address
the 256 bytes in Data Space memory with a single
two-byte instruction.
Short Direct. The core can address the four RAM
registers X,Y,V,W (locations 80h, 81h, 82h, 83h) in
the short-direct addressing mode. In this case, the
instruction is only one byte and the selection of the
location to be processed is contained in the op-
code. Short direct addressing is a subset of the di-
rect addressing mode. (Note that 80h and 81h are
also indirect registers).
Indirect. In the indirect addressing mode, the byte
processed by the register-indirect instruction is at
the address pointed by the content of one of the in-
direct registers, X or Y (80h,81h). The indirect reg-
ister is selected by the bit 4 of the opcode. A regis-
ter indirect instruction is one byte long.
Inherent. In the inherent addressing mode, all the
information necessary to execute the instruction is
contained in the opcode. These instructions are
one byte long.
Extended. In the extended addressing mode, the
12-bit address needed to define the instruction is
obtained by concatenating the four less significant
55/74
55
ST62T40B/E40B
5.3 INSTRUCTION SET
The ST6 core offers a set of 40 basic instructions
which, when combined with nine addressing
modes, yield 244 usable opcodes. They can be di-
vided into six different types: load/store, arithme-
tic/logic, conditional branch, control instructions,
jump/call, and bit manipulation. The following par-
agraphs describe the different types.
Load & Store. These instructions use one, two or
three bytes in relation with the addressing mode.
One operand is the Accumulator for LOAD and the
other operand is obtained from data memory using
one of the addressing modes.
For Load Immediate one operand can be any of
the 256 data space bytes while the other is always
immediate data.
All the instructions belonging to a given type are
presented in individual tables.
Table 24. Load & Store Instructions
Flags
Instruction
LD A, X
Addressing Mode
Short Direct
Bytes
Cycles
Z
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
C
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
1
1
1
1
1
1
1
1
2
2
1
1
1
1
2
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
LD A, Y
LD A, V
LD A, W
LD X, A
LD Y, A
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Short Direct
Direct
LD V, A
LD W, A
LD A, rr
LD rr, A
Direct
LD A, (X)
LD A, (Y)
LD (X), A
LD (Y), A
LDI A, #N
LDI rr, #N
Indirect
Indirect
Indirect
Indirect
Immediate
Immediate
Notes:
X,Y. Indirect Register Pointers, V & W Short Direct Registers
# . Immediate data (stored in ROM memory)
rr. Data space register
∆. Affected
* . Not Affected
56/74
56
ST62T40B/E40B
INSTRUCTION SET (Cont’d)
Arithmetic and Logic. These instructions are
used to perform the arithmetic calculations and
logic operations. In AND, ADD, CP, SUB instruc-
tions one operand is always the accumulator while
the other can be either a data space memory con-
tent or an immediate value in relation with the ad-
dressing mode. In CLR, DEC, INC instructions the
operand can be any of the 256 data space ad-
dresses. In COM, RLC, SLA the operand is always
the accumulator.
Table 25. Arithmetic & Logic Instructions
Flags
Instruction
ADD A, (X)
Addressing Mode
Indirect
Bytes
Cycles
Z
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
C
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
1
1
2
2
1
1
2
2
2
3
1
1
1
2
2
1
1
1
1
2
2
1
1
1
1
1
1
2
2
1
1
1
2
1
1
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
ADD A, (Y)
ADD A, rr
ADDI A, #N
AND A, (X)
AND A, (Y)
AND A, rr
ANDI A, #N
CLR A
Indirect
Direct
Immediate
Indirect
Indirect
Direct
Immediate
Short Direct
Direct
CLR r
COM A
Inherent
Indirect
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
∆
*
CP A, (X)
CP A, (Y)
CP A, rr
CPI A, #N
DEC X
Indirect
Direct
Immediate
Short Direct
Short Direct
Short Direct
Short Direct
Direct
DEC Y
*
DEC V
*
DEC W
*
DEC A
*
DEC rr
Direct
*
DEC (X)
DEC (Y)
INC X
Indirect
*
Indirect
*
Short Direct
Short Direct
Short Direct
Short Direct
Direct
*
INC Y
*
INC V
*
INC W
*
INC A
*
INC rr
Direct
*
INC (X)
Indirect
*
INC (Y)
Indirect
*
RLC A
Inherent
Inherent
Indirect
∆
∆
∆
∆
∆
∆
SLA A
SUB A, (X)
SUB A, (Y)
SUB A, rr
SUBI A, #N
Indirect
Direct
Immediate
Notes:
X,Y.Indirect Register Pointers, V & W Short Direct RegistersD. Affected
# . Immediate data (stored in ROM memory)* . Not Affected
rr. Data space register
57/74
57
ST62T40B/E40B
INSTRUCTION SET (Cont’d)
Conditional Branch. The branch instructions
achieve a branch in the program when the select-
ed condition is met.
Control Instructions. The control instructions
control the MCU operations during program exe-
cution.
Bit Manipulation Instructions. These instruc-
tions can handle any bit in data space memory.
One group either sets or clears. The other group
(see Conditional Branch) performs the bit test
branch operations.
Jump and Call. These two instructions are used
to perform long (12-bit) jumps or subroutines call
inside the whole program space.
Table 26. Conditional Branch Instructions
Flags
Instruction
Branch If
Bytes
Cycles
Z
*
*
*
*
*
*
C
*
JRC e
C = 1
1
1
1
1
3
3
2
2
2
2
5
5
JRNC e
C = 0
Z = 1
*
JRZ e
*
JRNZ e
Z = 0
*
JRR b, rr, ee
JRS b, rr, ee
Bit = 0
Bit = 1
∆
∆
Notes:
b.
e.
3-bit address
rr. Data space register
∆ . Affected. The tested bit is shifted into carry.
5 bit signed displacement in the range -15 to +16<F128M>
ee. 8 bit signed displacement in the range -126 to +129
* . Not Affected
Table 27. Bit Manipulation Instructions
Flags
Instruction
Addressing Mode
Bytes
Cycles
Z
C
*
SET b,rr
Bit Direct
Bit Direct
2
2
4
4
*
*
RES b,rr
*
Notes:
b.
3-bit address;
* . Not<M> Affected
rr. Data space register;
Table 28. Control Instructions
Flags
Instruction
Addressing Mode
Bytes
Cycles
Z
*
C
*
NOP
Inherent
Inherent
Inherent
Inherent
Inherent
1
1
1
1
1
2
2
2
2
2
RET
*
*
RETI
∆
*
∆
*
STOP (1)
WAIT
*
*
Notes:
1.
This instruction is deactivated<N>and a WAIT is automatically executed instead of a STOP if the watchdog function is selected.
∆ . Affected
*.
Not Affected
Table 29. Jump & Call Instructions
Instruction
Flags
Addressing Mode
Bytes
Cycles
Z
*
C
*
CALL abc
JP abc
Extended
Extended
2
2
4
4
*
*
Notes:
abc. 12-bit address;
* . Not Affected
58/74
58
ST62T40B/E40B
Opcode Map Summary. The following table contains an opcode map for the instructions used by the ST6
LOW
LOW
0
0000
1
0001
2
0010
3
0011
4
0100
5
0101
6
0110
7
0111
HI
HI
2
JRNZ 4
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
ext 1
CALL 2
abc
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
5
JRR
b0,rr,ee
bt
JRS
b0,rr,ee
bt
JRR
b4,rr,ee
bt
JRS
b4,rr,ee
bt
JRR
b2,rr,ee
bt
JRS
b2,rr,ee
bt
JRR
b6,rr,ee
bt
JRS
b6,rr,ee
bt
JRR
b1,rr,ee
bt
JRS
b1,rr,ee
bt
JRR
b5,rr,ee
bt
JRS
b5,rr,ee
bt
JRR
b3,rr,ee
bt
JRS
b3,rr,ee
bt
JRR
b7,rr,ee
bt
JRS
b7,rr,ee
2
JRZ
2
JRC
4
LD
0
0
e
e
e
e
e
e
e
e
e
e
e
#
x
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
a,(x)
a,nn
0000
0000
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
prc
JRC
1
4
ind
LDI
4
1
INC 2
1
0001
1
0001
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
sd
1
2
prc
JRC
2
4
imm
CP
2
0010
2
0010
#
a,(x)
1
2
pcr
JRNZ 4
2
3
5
1
2
e
1
2
pcr
JRZ
1
2
prc
JRC
1
4
ind
CPI
4
1
LD
sd
3
0011
3
0011
a,x
#
a,nn
1
2
pcr
JRNZ 4
2
3
5
pcr
JRZ
1
2
prc
JRC
2
4
imm
ADD
a,(x)
4
0100
4
0100
e
e
e
e
e
e
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
prc
JRC
1
4
ind
ADDI
4
1
INC 2
5
0101
5
0101
y
a,nn
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
sd
1
2
prc
JRC
2
4
imm
INC
6
0110
6
0110
#
(x)
#
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
2
prc
JRC
1
ind
4
1
LD
sd
7
0111
7
0111
a,y
#
1
2
pcr
2
3
5
1
2
pcr
JRZ
1
2
prc
JRC
JRNZ 4
e
4
1
LD
ind
8
1000
8
1000
(x),a
#
1
2
pcr
RNZ
e
2
4
3
5
1
2
pcr
JRZ
1
prc
JRC
4
1
INC 2
9
1001
9
1001
v
1
2
pcr
2
3
5
1
2
pcr
JRZ
sd
1
2
prc
JRC
JRNZ 4
4
AND
a,(x)
A
1010
A
1010
e
e
e
e
e
e
e
e
e
e
e
e
#
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
2
prc
JRC
1
4
ind
ANDI
4
1
LD
sd
B
1011
B
1011
a,v
#
a,nn
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
2
prc
JRC
2
4
imm
SUB
C
1100
C
1100
a,(x)
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
prc
JRC
1
4
ind
SUBI
4
1
INC 2
D
1101
D
1101
w
a,nn
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
sd
1
2
prc
JRC
2
4
imm
DEC
E
1110
E
1110
#
(x)
#
1
2
pcr
JRNZ 4
2
3
5
1
2
pcr
JRZ
1
2
prc
JRC
1
ind
4
1
LD
sd
F
1111
F
1111
a,w
1
pcr
2
ext 1
pcr
3
bt
1
pcr
1
prc
Abbreviations for Addressing Modes: Legend:
dir
sd
Direct
Short Direct
#
e
b
rr
nn
abc
ee
Indicates Illegal Instructions
5 Bit Displacement
3 Bit Address
1byte dataspace address
1 byte immediate data
12 bit address
Cycle
Mnemonic
2
1
JRC
prc
Operand
Bytes
imm Immediate
e
inh
ext
b.d
bt
Inherent
Extended
Bit Direct
Bit Test
Addressing Mode
8 bit Displacement
pcr
ind
Program Counter Relative
Indirect
59/74
59
ST62T40B/E40B
Opcode Map Summary (Continued)
LOW
LOW
8
1000
9
1001
A
1010
B
1011
C
1100
D
1101
E
1110
F
1111
HI
HI
2
JRNZ 4
JP
2
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
pcr
JRNC
e
4
RES
b0,rr
b.d 1
SET 2
b0,rr
b.d 1
RES
b4,rr
b.d 1
SET 2
b4,rr
b.d 1
RES
b2,rr
b.d 1
SET 2
b2,rr
b.d 1
RES
b6,rr
b.d 1
SET 2
b6,rr
b.d 1
RES
b1,rr
b.d 1
SET 2
b1,rr
b.d 1
RES
b5,rr
b.d 1
SET 2
b5,rr
b.d 1
RES
b3,rr
b.d 1
SET 2
b3,rr
2
JRZ
4
LDI
2
JRC
4
LD
0
0
e
e
e
e
e
e
e
e
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
abc
e
e
e
rr,nn
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
e
a,(y)
a,rr
0000
0000
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
3
4
imm
DEC
1
2
prc
JRC
1
4
ind
LD
2
1
0001
1
0001
x
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
sd
COM
1
2
prc
JRC
2
4
dir
CP
2
2
2
0010
2
0010
a
a,(y)
a,rr
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
2
prc
JRC
1
4
ind
CP
2
4
LD
3
0011
3
0011
e
x,a
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
2
sd
RETI
1
2
prc
JRC
2
4
dir
ADD
a,(y)
2
2
4
0100
4
0100
e
e
e
e
e
e
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
inh 1
DEC
prc
JRC
1
4
ind
ADD
2
2
5
0101
5
0101
y
a,rr
(y)
rr
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
2
sd
STOP 2
1
prc
JRC
2
4
dir
INC
2
2
6
0110
6
0110
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
inh 1
prc
JRC
1
4
ind
INC
2
LD
sd
2
7
0111
7
0111
y,a
#
1
2
pcr
2
ext 1
JP
2
4
pcr
JRZ
1
1
2
prc
JRC
2
4
dir
LD
JRNZ 4
e
2
2
8
1000
8
1000
(y),a
rr,a
1
2
pcr
RNZ
e
2
4
ext 1
JP
2
4
pcr
JRZ
1
2
prc
JRC
1
4
ind
LD
2
4
DEC
9
1001
9
1001
v
1
2
pcr
2
ext 1
JP
2
4
pcr
JRZ
1
4
sd
RCL
1
2
prc
JRC
2
4
dir
AND
a,(y)
JRNZ 4
2
2
A
1010
A
1010
e
e
e
e
e
e
e
e
e
e
e
e
a
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
inh 1
LD
prc
JRC
1
4
ind
AND
2
2
B
1011
B
1011
v,a
a,rr
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
2
sd
RET
1
2
prc
JRC
2
4
dir
SUB
2
2
C
1100
C
1100
a,(y)
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
inh 1
DEC
prc
JRC
1
4
ind
SUB
2
2
D
1101
D
1101
w
a,rr
(y)
rr
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
b.d 1
RES
b7,rr
b.d 1
SET 2
b7,rr
pcr
JRZ
1
2
sd
WAIT 2
1
prc
JRC
2
4
dir
DEC
2
2
E
1110
E
1110
1
2
pcr
JRNZ 4
2
ext 1
JP
2
4
pcr
JRZ
1
4
inh 1
prc
JRC
1
4
ind
DEC
2
LD
sd
2
1
F
1111
F
1111
w,a
1
pcr
2
ext 1
pcr
2
b.d 1
pcr
1
prc
2
dir
Abbreviations for Addressing Modes: Legend:
dir
sd
Direct
Short Direct
#
e
b
rr
nn
abc
ee
Indicates Illegal Instructions
5 Bit Displacement
3 Bit Address
1byte dataspace address
1 byte immediate data
12 bit address
Cycle
Mnemonic
2
1
JRC
prc
Operand
Bytes
imm Immediate
e
inh
ext
b.d
bt
Inherent
Extended
Bit Direct
Bit Test
Addressing Mode
8 bit Displacement
pcr
ind
Program Counter Relative
Indirect
60/74
60
ST62T40B/E40B
6 ELECTRICAL CHARACTERISTICS
6.1 ABSOLUTE MAXIMUM RATINGS
This product contains devices to protect the inputs
against damage due to high static voltages, how-
ever it is advisable to take normal precaution to
avoid application of any voltage higher than the
specified maximum rated voltages.
Power Considerations.The average chip-junc-
tion temperature, Tj, in Celsius can be obtained
from:
Tj=
TA + PD x RthJA
Where:TA =
Ambient Temperature.
For proper operation it is recommended that V
I
RthJA = Package thermal resistance
(junction-to ambient).
and V be higher than V and lower than V .
O
SS
DD
Reliability is enhanced if unused inputs are con-
PD =
Pint + Pport.
nected to an appropriate logic voltage level (V
DD
or V ).
Pint = IDD x VDD (chip internal power).
SS
Pport = Port power dissipation (deter-
mined by the user).
Symbol
Parameter
Value
Unit
V
V
Supply Voltage
Input Voltage
Output Voltage
-0.3 to 7.0
DD
(1)
(1)
V
V
V
- 0.3 to V
+ 0.3
+ 0.3
V
I
SS
SS
DD
DD
V
- 0.3 to V
V
O
I
IV
IV
Current Drain per Pin Excluding V , V
±10
50
mA
mA
mA
°C
°C
O
DD SS
Total Current into V (source)
DD
SS
DD
Total Current out of V (sink)
50
SS
Tj
Junction Temperature
Storage Temperature
150
T
-60 to 150
STG
Notes:
-
Stresses above those listed as ”absolute maximum ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
- (1) Within these limits, clamping diodes are guarantee to be not conductive. Voltages outside these limits are authorised as long as injection
current is kept within the specification.
61/74
61
ST62T40B/E40B
6.2 RECOMMENDED OPERATING CONDITIONS
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
6 Suffix Version
1 Suffix Version
-40
0
85
70
TA
Operating Temperature
Operating Supply Voltage
°C
V
f
= 4MHz
3.0
4.5
6.0
6.0
OSC
VDD
fosc= 8MHz
V
V
= 3V
= 4.5V
0
0
4.0
8.0
2)
DD
DD
f
Oscillator Frequency
MHz
OSC
IINJ+
IINJ-
Pin Injection Current (positive) VDD = 4.5 to 5.5V
Pin Injection Current (negative) VDD = 4.5 to 5.5V
+5
-5
mA
mA
Notes:
1. Care must be taken in case of negative current injection, where adapted impedance must be respected on analog sources to not affect the
A/D conversion. For a -1mA injection, a maximum 10 KΩ is recommanded.
2. An oscillator frequency above 1MHz is recommended for reliable A/D results.
Figure 34. Maximum Operating FREQUENCY (Fmax) Versus SUPPLY VOLTAGE (VDD)
Maximum FREQUENCY (MHz)
8
7
6
5
4
3
2
1
FUNCTIONALITYIS NOT
GUARANTEEDIN
THIS AREA
2.5
3
3.5
4
4.5
5
5.5
6
SUPPLY VOLTAGE (VDD)
The shaded area is outside the recommended operating range; device functionality is not guaranteed under these conditions.
62/74
62
ST62T40B/E40B
6.3 DC ELECTRICAL CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
V
Input Low Level Voltage
All Input pins
IL
V
x 0.3
V
V
V
DD
V
Input High Level Voltage
All Input pins
IH
V
x 0.7
DD
(1)
Hysteresis Voltage
V
V
= 5V
= 3V
0.2
0.2
DD
DD
V
Hys
All Input pins
Low Level Output Voltage
All Output pins
V
V
= 5.0V; I = +10µA
0.1
0.8
DD
DD
OL
= 5.0V; I = + 5mA
OL
V
V
V
V
V
= 5.0V; I = +10µA
0.1
0.8
1.3
OL
DD
DD
DD
OL
Low Level Output Voltage
20 mA Sink I/O pins
= 5.0V; I = +10mA
OL
= 5.0V; I = +20mA
OL
V
High Level Output Voltage
All Output pins
V
V
= 5.0V; I = -10µA
4.9
3.5
OH
DD
DD
OL
V
= 5.0V; I = -5.0mA
OL
All Input pins
RESET pin
40
100
350
200
900
R
Pull-up Resistance
ΚΩ
PU
150
Input Leakage Current
All Input pins but RESET
V
V
= V (No Pull-Up configured)
IN
IN
SS
0.1
-16
1.0
= V
I
I
DD
IL
µA
Input Leakage Current
RESET pin
V
V
= V
-8
-30
10
IH
IN
IN
SS
= V
DD
Supply Current in RESET
Mode
V
=V
RESET SS
7
7
mA
mA
mA
µA
f
=8MHz
OSC
Supply Current in
V
V
=5.0V
f
=8MHz
=8MHz
(2)
DD
INT
RUN Mode
I
DD
Supply Current in WAIT
=5.0V
f
2
(3)
DD
INT
Mode
Supply Current in STOP
I
V
=0mA
=5.0V
LOAD
10
(3)
Mode
DD
Notes:
(1) Hysteresis voltage between switching levels
(2) All peripherals running
(3) All peripherals in stand-by
63/74
63
ST62T40B/E40B
6.4 AC ELECTRICAL CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
(1)
t
Supply Recovery Time
100
ms
REC
Minimum Pulse Width (V = 5V)
DD
T
RESET pin
NMI pin
100
100
ns
WR
TA = 25°C
TA = 85°C
5
10
10
20
T
EEPROM Write Time
ms
WEE
Endurance EEPROM WRITE/ERASE Cycle
Retention EEPROM Data Retention
QA LOT Acceptance
TA = 55°C
300,000 1 million
10
cycles
years
pF
C
Input Capacitance
Output Capacitance
All Inputs Pins
All Outputs Pins
10
10
IN
C
pF
OUT
Notes:
1. Period for which V has to be connected at 0V to allow internal Reset function at next power-up.
DD
6.5 A/D CONVERTER CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
8
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
Res
Resolution
Total Accuracy
Bit
LSB
µs
f
f
> 1.2MHz
> 32kHz
±2
±4
(1) (2)
OSC
OSC
A
TOT
t
Conversion Time
f
= 8MHz
70
C
OSC
Conversion result when
= V
ZIR
Zero Input Reading
00
Hex
V
IN
SS
Conversion result when
FSR
Full Scale Reading
FF
Hex
V
= V
IN
DD
Analog Input Current During
Conversion
AD
V
= 4.5V
1.0
5
µA
I
DD
AC
Analog Input Capacitance
2
pF
IN
Notes:
1. Noise at AV , AV <10mV
DD
SS
2. With oscillator frequencies less than 1MHz, the A/D Converter accuracy is decreased. .
64/74
64
ST62T40B/E40B
6.6 TIMER CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
fINT
8
f
Input Frequency on TIMER Pin*
Pulse Width at TIMER Pin*
MHz
IN
---------
V
V
= 3.0V
>4.5V
1
125
µs
ns
DD
DD
t
W
Note*: When available.
6.7 SPI CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
F
Clock Frequency
Set-up Time
Hold Time
Applied on Scl
Applied on Sin
Applied onSin
1
MHz
ns
CL
t
50
SU
t
100
ns
h
6.8 LCD ELECTRICAL CHARACTERISTICS
(T = -40 to +85°C unless otherwise specified)
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
V
DC Offset Voltage
V
= Vdd, no load
LCD
50
mV
os
COM High Level, Output Voltage
SEG High Level, Output Voltage
I=100µA, V
=5V
=5V
=5V
LCD
V
4.5
OH
I=50µA, V
LCD
COM Low Level, Output Voltage
SEG Low Level, Output Voltage
I=100µA, V
V
LCD
V
0.5
10
OL
I=50µA, V
=5V
LCD
V
Display Voltage
See Note 2
V
-0.2
LCD
DD
Notes:
1. The DC offset refers to all segment and common outputs. It is the difference between the measured voltage value and nominal value for
every voltage level.
2. An external resistor network is required when VLCD is lower then 4.5V.
6.9 PSS ELECTRICAL CHARACTERISTICS (When available)
(T = -40 to +85°C unless otherwise specified
A
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
V
PSS pin Input Voltage
Vss
V
V
PSS
DD
V
=5.0V, T = 25°C
A
PSS
I
PSS pin Input Current
PSS Running
PSS Stopped
350
1
µA
PSS
65/74
65
ST62T40B/E40B
7 GENERAL INFORMATION
7.1 PACKAGE MECHANICAL DATA
Figure 35. 80-Pin Plastic Quad Flat Package
mm
inches
D
Dim.
A
Min Typ Max Min Typ Max
A2
D1
D2
A
3.40
0.134
0.020
A1
A1 0.25
0.50 0.010
A2 2.50 2.70 2.90 0.098 0.106 0.114
b
b
c
0.29
0.11
0.45 0.011
0.23 0.004
0.018
0.009
D
23.20
20.00
18.40
17.20
14.00
12.00
0.80
0.913
0.787
0.724
0.677
0.551
0.472
0.031
e
D1
D2
E
E2 E1
E
E1
E2
e
L
L
0.73 0.88 1.03 0.029 0.035 0.041
c
1.60 mm
0×- 7×
Number of Pins
N
80
Figure 36. 80-Pin Ceramic Quad Flat Package
mm
Min Typ Max Min Typ Max
3.24 0.128
inches
Dim
A
A1
B
0.20
0.008
0.30 0.35 0.45 0.012 0.014 0.018
0.13 0.15 0.23 0.005 0.006 0.009
23.35 23.90 24.45 0.919 0.941 0.963
C
D
D1 19.57 20.00 20.43 0.770 0.787 0.804
D3
E
18.40
0.724
17.35 17.90 18.45 0.683 0.705 0.726
E1 13.61 14.00 14.39 0.536 0.551 0.567
E3
e
12.00
0.80
0.472
0.031
G
13.75 14.00 14.25 0.541 0.551 0.561
G1 19.75 20.00 20.25 0.778 0.787 0.797
G2
L
1.17
0.35 0.80
8.89
0.046
0.014 0.031
0.350
CQFP080W
Ø
Number of Pins
80
N
66/74
66
ST62T40B/E40B
GENERAL INFORMATION (Cont’d)
7.2 PACKAGE THERMAL CHARACTERISTIC
Value
Typ.
Symbol
Parameter
Test Conditions
Unit
Min.
Max.
PQFP80
70
RthJA
Thermal Resistance
°C/W
70
CQFP80W
7.3 .ORDERING INFORMATION
Table 30. OTP/EPROM VERSION ORDERING INFORMATION
Program
Sales Type
I/O
Temperature Range
Package
Memory (Bytes)
7948 (EPROM)
7948 (OTP)
ST62E40BG1
ST62T40BQ6
0 to 70°C
CQFP80W
PQFP80
16 to 24
-40 to 85°C
67/74
67
ST62T40B/E40B
Notes:
68/74
68
ST6240B
8-BIT ROM MCU WITH LCD DRIVER,
EEPROM AND A/D CONVERTER
■ 3.0 to 6.0V Supply Operating Range
■ 8 MHz Maximum Clock Frequency
■ -40 to +85°C Operating Temperature Range
■ Run, Wait and Stop Modes
■ 5 Interrupt Vectors
■ Look-up Table capability in Program Memory
■ Data Storage in Program Memory:
User selectable size
■ Data RAM: 192 bytes
■ Data EEPROM: 128 bytes
■ 24 I/O pins, fully programmable as:
– Input with pull-up resistor
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
PQFP80
(See end of Datasheet for Ordering Information)
– LCD segments (8 combiport lines)
■ 4 I/O lines can sink up to 20mA to drive LEDs or
TRIACs directly
■ Two
8-bit
Timer/Counter
with
7-bit
programmable prescaler
■ Digital Watchdog
■ 8-bit A/D Converter with 12 analog inputs
■ 8-bit Synchronous Peripheral Interface (SPI)
■ LCD driver with 45 segment outputs, 4
backplane outputs and selectable multiplexing
ratio.
■ 32kHz oscillator for stand-by LCD operation
■ Power Supply Supervisor (PSS)
■ On-chip Clockoscillator canbe driven by Quartz
Crystal or Ceramic resonator
■ One external Non-Maskable Interrupt
■ ST6240-EMU2 Emulation and Development
System (connects to an MS-DOS PC via a
parallel port).
DEVICE SUMMARY
ROM
DEVICE
I/O Pins
(Bytes)
ST6240B
7948
16 to 24
Rev. 2.7
July 2001
69/74
69
ST6240B
1.2 ROM READOUT PROTECTION
1 GENERAL DESCRIPTION
If the ROM READOUT PROTECTION option is
selected, a protection fuse can be blown to pre-
vent any access to the program memory content.
1.1 INTRODUCTION
The ST6240B is mask programmed ROM version
of ST62T40B OTP devices.
In case the user wants to blow this fuse, high volt-
age must be applied on the TEST pin.
They offer the same functionality as OTP devices,
selecting as ROM options the options defined in
the programmable option byte of the OTP version.
Figure 2. Programming circuit
Figure 1. Programming wave form
0.5s min
TEST
5V
47mF
100nF
15
14V typ
10
V
SS
5
V
DD
PROTECT
TEST
150 µs typ
14V
TEST
100nF
100mA
max
ZPD15
15V
VR02003
4mA typ
t
VR02001
Note: ZPD15 is used for overvoltage protection
70/74
70
ST6240B
1.3 ORDERING INFORMATION
The following section deals with the procedure for
transfer of customer codes to STMicroelectronics.
part of the contractual agreement for the creation
of the specific customer mask.
1.3.1 Transfer of Customer Code
The STMicroelectronics Sales Organization will be
pleased to provide detailed information on con-
tractual points.
Customer code is made up of the ROM contents
and the list of the selected mask options. The
ROM contents are to be sent on diskette, or by
electronic means, with the hexadecimal file gener-
ated by the development tool. All unused bytes
must be set to FFh.
Table 1. ROM Memory Map for ST6240B
ROM Page Device Address
Description
The selected mask options are communicated to
STMicroelectronics using the correctly filled OP-
TION LIST appended. See page 72.
0000h-007Fh
Page 0
Reserved
User ROM
0080h-07FFh
0800h-0F9Fh
0FA0h-0FEFh
User ROM
Reserved
1.3.2 Listing Generation and Verification
Page 1
“STATIC”
0FF0h-0FF7h
0FF8h-0FFBh
0FFCh-0FFDh
0FFEh-0FFFh
Interrupt Vectors
Reserved
NMI Vector
Reset Vector
When STMicroelectronics receives the user’s
ROM contents, a computer listing is generated
from it. This listing refers exactly to the mask which
will be used to produce the specified MCU. The
listing is then returned to the customer who must
thoroughly check, complete, sign and return it to
STMicroelectronics. The signed listing forms a
0000h-000Fh
0010h-07FFh
Reserved
User ROM
Page 2
Page 3
0000h-000Fh
0010h-07FFh
Reserved
User ROM
Table 2. ROM version Ordering Information
Sales Type
ROM
I/O
Temperature Range
Package
ST6240BQ1/XXX
ST6240BQ6/XXX
0 to +70°C
-40 to 85°C
7948
16 to 24
PQFP80
71/74
71
ST6240B
ST6240B MICROCONTROLLER OPTION LIST
Customer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact:
Phone:
Reference: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STMicroelectronics references:
Device:
[ ] ST6240B (8 KB)
Package:
[ ] Plastic Quad Flat Package (Tape & Reel)
Temperature Range:
Marking:
[ ] 0°C to + 70°C
[ ] - 40°C to + 85°C
[ ] Standard marking
[ ] Special marking (ROM only):
PQFP80 (10 char. max): _ _ _ _ _ _ _ _ _ _
Authorized characters are letters, digits, ’.’, ’-’, ’/’ and spaces only.
Timer pull-up:
[ ] Enabled
[ ] Disabled
Watchdog Selection:
Readout Protection:
[ ] Software Activation
[ ] Hardware Activation
[ ] Enabled:
[ ] Fuse is blown by STMicroelectronics
[ ] Fuse can be blown by the customer
[ ] Disabled
NMI pull-up:
[ ] Enabled
[ ] Disabled
Comments:
Number of segments and backplanes used: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Operating Range in the application: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator Frequency in the application:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes:
Date:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signature: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72/74
72
ST6240B
2 SUMMARY OF CHANGES
Rev.
Main Changes
Date
Changed ORB register address (CE instead of CD) in section 4.1.5 on page 38.
Updated Table 19 on page 48.
Removed two tables: “oscillator source selection” and “32KHz Division Factor for base frequency se-
lection” (section 4.5 on page 48).
2.7
July 2001
Changed Figure 35 on page 66.
Changed option list (page 72).
73/74
ST6240B
Notes:
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of useof such information nor for any infringement of patents or other rights of third parties which may result from its use. No license isgranted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without the express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2001 STMicroelectronics - All Rights Reserved.
Purchase of I2C Components by STMicroelectronics conveys a license under the Philips I2C Patent. Rights to use these components in an
I2C system is granted provided that the system conforms to the I2C Standard Specification as defined by Philips.
STMicroelectronics Group of Companies
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain
Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
74/74
相关型号：
ST62E40C
GANG PROGRAMMERS FOR ST62 MCU FAMILYWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E40G1
8-Bit MicrocontrollerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ST62E42
EPROM PROGRAMMING BOARDS FOR ST62 MCU FAMILYWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E42B
8-BIT OTP/EPROM MCU WITH LCD DRIVER, EEPROM AND A/D CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E42BG1
IC-SM-8-BIT MCU 8K EPROMWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E42C
GANG PROGRAMMERS FOR ST62 MCU FAMILYWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E42G1
8-Bit MicrocontrollerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ST62E42G6
8-BIT, UVPROM, 8.4MHz, MICROCONTROLLER, CQFP64, WINDOWED, CERAMIC, QFP-64Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E45B
8-BIT OTP/EPROM MCU WITH LCD DRIVER, EEPROM AND A/D CONVERTERWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
ST62E45BG1
8-Bit MicrocontrollerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ST62E45G1
8-Bit MicrocontrollerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
ETC
ST62E45G6
8-BIT, UVPROM, 8.4MHz, MICROCONTROLLER, CQFP52, WINDOWED, CERAMIC, QFP-52Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明