T1206C103JCT [ETC]

Multilayer Ceramic Capacitors;


型号：	T1206C103JCT
厂家：	ETC
描述：	Multilayer Ceramic Capacitors
文件：	总19页 (文件大小：696K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Nickel Barrier

Multilayer Ceramic Capacitors

Features:

• Multilayer ceramic chip capacitor.

• Nickel barrier termination.

• High performance and reliability.

• 0603, 0805, and 1206 case size.

Rated Voltage

Code

Rated Voltage

100

Part Dimension

Dimensions

Maximum

Thickness

(T)

Length

(L)

Width

(W)

Minimum

Voltage

(V)

Type

1.6 ±0.1

0.8 ±0.1

0.20

0.40

0.70

1.40

6.3 ~ 50

6.3 ~ 500

6.3 ~ 1000

0603

0805

1206

2.0 ±0.2

3.2 ±0.2

1.25 ±0.1

1.60 ±0.2

1.40

1.52

0.25

Page 1

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Temperature Characteristics Code

Operation Temperature

Code

Temperature Coefficient

Capacitance Change

(°C)

NPO (Class I)

X7R (Class II)

Y5V (Class II)

0 ±30ppm/°C

±15%

-55°C ~ +125

30°C ~ +85

+22% ~ -82%

Capacitance Code

Capacitance

Code

(pF)

010

1R5

100

101

102

103

222

472

1.5

10*

100*

1000*

10000*

2200*

4700*

Tolerance Code

Tolerance

(%)

Code

±5

±10

+80/-20

PS:

* -- Two significant digits followed by number of zeros.

Temperature coefficient (T.C.) vs. Proper tolerance applied:

NPO:

For all tolerance

K+M Tolerance

M+Z Tolerance

X7R+X5R:

Y5V+Z5U:

Termination Code

Code

Termination Type

Nickel

Packaging Code

Code

Packaging Type

Bulk

Tape and Reel

Standard Test Conditions

Tests shall, unless otherwise specified, be carried out at 15 to 35°C and RH 45 to 75%.If any doubt and argument has been

D^eni^cs^op^uno^tes^riⁱtⁿio^jun^{dgement, the final test shall be done at 25 ±2°C, RH45 to 55% and 860 ~ 1060mbar. (Based on JIS standard).}

If question to the measuring result in judgement, take the capacitor under a specified temperature for 30 minutes at least before

measurement.

Page 2

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Structure

Ag/Pd Series

Number

Specifications

Material

Minimum Termination

Plating Thickness

(µ m)

Ceramic Dielectric

Internal Electrode

Ceramic

Ag-Pd

Ag layer

End Terminal

Ni layer

1.5 - 3.5

3 - 8

Sn-Pb layer or Sn layer

BME Series

Number

Specifications

Material

Minimum Termination

Plating Thickness

(µ m)

Ceramic Dielectric

Internal Electrode

End Termination

Ceramic

Cu layer

Ni layer

1.5 - 3.5

3 - 8

Sn-Pb layer or Sn layer

Storing Condition And Term

Recommends the storing of products within 6 months at temperature 15 ~ 35°C and humidity 70%RH maximum. If the product stored

over 6 months, please reconfirm its solderability before use.

Page 3

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Performance

Item

Performance

Test or Inspection Method

External

No defects which may affect

performance

Visual inspection and dimension measurement

Appearance

DC Tested voltage shall be applied for 1 ~ 5 second.

Charge/discharge current shall not exceed 50mA (PS : Ra

- Rated Voltage)

Temperature Coefficient

Code

NPO

X7R/X5R

2.5Ra

Y5V

Withstand test voltage without insulation

breakdown or other damage

Voltage Proof

≤200V

250V

2.0Ra

500V/630V

≥1KV

1.5Ra

1.25Ra

NPO:

Rated Voltage

DC Tested Voltage

100,000MΩ minimum or R x C ≥1000Ω x

F (Which ever is smaller)

X7R, X5R, Y5V, Z5U:

<1KV

1.0 Ra

Insulation Resistance

≥1KV

1KV

10,000MΩ minimum or R x C ≥ 1000Ω x

F (Which ever is smaller)

Apply DC tested voltage for 60 ±5 minute.

(PS : Ra - Rated Voltage)

Capacitance

(Cap.)

Within the specified tolerance

NPO:

≥30pF: Q ≥ 1000

<30pF: Q ≥ 400 + 20C

PS:C: Nominal Capacitance (pF)

X7R, X5R, Y5V, and Z5U : (Maximum

Value)

Measuring Frequency:

Z5U,Y5V, X7R, X5R : 1KHz ±50Hz

NPO:

>1000pF:1KHz ±50Hz.

≤1000pF:1MHz 100KHz.

Measuring Voltage:

≥

≤10V

T.C.

25V

16V

50V

2.5% 3.0% 3.5% 5.0%

Dissipation Factor (D.F)

Z5U:0.5V

NPO:

rms.

X7R/

X5R

X7R, X5R, Y5V:1.0 ±0.2V

rms.

Z5U

4.0%

Y5V

5.0% 7.5% 9.0% 12.5%

Page 4

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Item

Performance

Test or Inspection Method

Temperatures Coefficient

The temperature coefficient is determined using the

capacitance measured in step 3 as a reference. Test the

specimen from step 1through step 5, the capacitance shall

be within the specified tolerance for the capacitance

coefficient and capacitance change as left table.

Operating

Capacitance

Change (DC)

Temperature

NPO -55 ~ +125°C 0 ±30 (ppm/°C)

X7R -55 ~ +125°C

X5R -55 ~ +85°C

±15%

Temperature

Characteristic

of Capacitance

Code

Temperature Coefficient

Base Temperature (25°C) ±2°C

Minimum Operation Temperature ±2°C

Base Temperature (25°C) ±2°C

Y5V -55 ~ +125°C +22% ~ -82%

Z5U -55 ~ +125°C +22% ~ -56%

Minimum Operation Temperature ±2°C

Base Temperature (25°C) ±2°C

Completely soak both terminal electrodes in

solder at specified temperature for 3 ±0.5 second

a. For Tin-Lead Sn/Pb) Termination product:

235 ±5°C.

Solderabiliy

Leaching

New solder to over 95% of termination

No mechanical Damage

b. For Lead-free (Pure Sn) Termination

product: 245 ±5°C.

Completely soak both terminal electrodes in solder at 270

±5°C for 40 ±1second.

External

Appearance

NPO

±2.5% or ±0.25 pF maximum

Capacitance

Change

(Whichever is larger)

X7R/X5

±7.5%

(∆ C/C)

±20%

Z5U

±20%

Y5V

Completely immerse both

terminations in solder at 270 ±5°C for 10 ±3 second.

NPO: C ≥30pF : Q ≥ 1000

C<30pF:Q ≥ 400 + 20°C

Soldering

to heat

PS: C : Nominal Capacitance (pF)

X7R, X5R, Y5V, Z5U : (Maximum Value)

Leave the capacitors in ambient condition for 2 4 ±2 hours

before measurement.

≥

≤10V

T.C.

25V

16V

50V

2.5% 3.0% 3.5% 5.0%

*Preconditioning: F(only for Class 2):

X7R/

X5R

Perform a heat treatment at 150 +0-10°C for one hour and

then let sit for 24 ±2 hours at room temperature.

Perform the initial measurement.

Z5U

4.0%

Y5V

5.0% 7.5% 9.0% 12.5%

NPO:

100,000MW minimum or R x C ≥1000W

x F (Whichever is smaller)

X7R, X5R, Y5V, Z5U:

10,000MW minimum or R x C ≥1000W

x F (Whichever is smaller)

Page 5

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Item

Performance

Test or Inspection Method

External

No mechanical damage

Appearance

NPO: ±5% or ±0.5 pF maximum

(Whichever is larger)

X7R/X5R: ±12.5%

Y5V: ±30%

Humidity load: (Not apply for the product with rated voltage

≥250V):

Apply the rated voltage at temperature 40 ±2°C and humidity

90 to 95%RH for 1000+48/-0 hours.

Leave the capacitors in ambient condition for the following time

before measurement.

Class 1: 1~2 hours.

Class 2: 24 ±2 hours.

Charge / discharge current shall not exceed 50 mA.

Preconditioning: (only for class 2):

Apply the rated DC voltage for 1hour at 40 ±2°C. Remove and

let sit for 48 ±4 hours at room temperature.

Perform initial measurement.

Humidity (steady state):

The test procedure is same as that in Humidity load but only

without rated voltage applied.

Capacitance

Change

(∆ C/C)

Z5U: ±30%

NPO: C ≥30pF: Q ≥ 350

10pF≤C<30pF:

Humidity

(Steady

State)

Q≥100+2.5°C

C<10pF: 200+10°C

and

PS: C: Nominal Capacitance (pF)

C<30pF:Q ≥ 400 + 20°C

PS: C : Nominal capacitance (pF)

X7R, X5R: Less than 2 times of initial

value

Humidity

Load

Y5V and Z5U: Less than 1.5 times of

initial value

500MΩ minimum or 25Ω *F

(Which ever is smaller)

External

No mechanical damage

Appearance

NPO: ±3% or ±0.3 pF maximum

(Whichever is larger)

X7R/X5R: ±12.5%

Y5V: ±30%

Capacitance

Change

Apply 2 x rated voltage at maximum operating temperature

±2°C for 1000 +48/-10 hours.

Leave the capacitors in ambient condition for the following time

before measurement.

(∆ C/C)

Z5U: ±30%

Load Life

NPO: C ≥30pF : Q ≥ 350

30pF>:C ≥10pF:

Class I: 1~2 hours

Class II: 24 ±2 hours

Q ≥ 275 +205°C

Charge / discharge current shall. not exceed 50 mA.

Preconditioning: (only for class 2):

Apply 200% of the rated DC voltage for 1 hour at the maximum

operating temperature ±3°C. Remove and let sit for 24 ±2

hours at room temperature.

C<10pF: Q ≥ 200 + 10°C

PS: C : Nominal capacitance (pF)

X7R, X5R: Less than 2 times of initial

value

Y5V and Z5U : Less than 1.5 times of

initial value

Perform initial measurement.

1000MΩ minimum or 50Ω *F

(Whichever is smaller)

Page 6

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Item

Performance

Test or Inspection Method

(Not apply for 0402 product)

External

Without distinct Damage

Appearance

Solder the capacitors to the test jig as shown in figure below

with IR-Reflow method. The capacitor shall be subjected to a

simple harmonic motion with the entire frequency range, from

10 to 55 Hz and return to 10 Hz ,shall be transverse in 1 min.

Amplitude (total excursion): 1.5mm

NPO: ±2.5% or ±0.25 pF maximum

(Whichever is larger)

Capacitance

Change

X7R/X5R: ±7.5%

(∆ C/C)

Y5V, Z5U: ±20%

NPO: C ≥30pF : Q ≥ 1000

C<30pF:Q ≥ 400 + 20°C

Amplitude tolerance: ± 15%

This motion shall be applied for a period of 2

hours in each of 3 mutually perpendicular

PS: C : Nominal capacitance (pF)

X7R, X5R, Y5V, Z5U : (Maximum Value)

Vibration

directions (a total of 6 hours)

≥

≤10V

T.C.

25V

16V

50V

2.5% 3.0% 3.5% 5.0%

4.0%

5.0% 7.5% 9.0% 12.5%

DF or Q

X7R/

X5R

Z5U

Y5V

External

No mechanical Damage

Appearance

Bending

Strength

Flexure ≥ 1mm

Deflection

NPO: ±5% or ±0.5 pF maximum

(Whichever is larger)

X7R/X5R: ±12.5%

Capacitance

Change

(∆ C/C)

Y5V: ±30%

(Not apply for 0402 product)

External

No mechanical Damage

Appearance

The capacitor shall be subject 5 cycles according to four heat

treatments listed in the following table.

Then leave the capacitors in ambient condition for the

following time before measurement.

Class II: 2~24 hours

NPO: ±2.5% or ±0.25 pF maximum

(Whichever is larger)

X7R/X5R: ±7.5%

Capacitance

Change

(∆ C/C)

Y5V: ±20%

NPO: C ≥30pF : Q ≥ 1000

C<30pF: Q ≥ 400 + 20°C

Duration

Step

Temperature (°C)

(Minutes)

X7R, X5R, Y5V and Z5U (Maximum value)

Minimum Operation Temperature ±3

Room Temperature (25°C)

30 ±3

Temperature

Cycle

2 ~ 5

30 ±3

2 ~ 5

≥

≤10V

T.C.

25V

16V

50V

2.5% 3.0% 3.5% 5.0%

Minimum Operation Temperature ±3

Room Temperature (25°C)

X7R/

X5R

Z5U

4.0%

Preconditioning: (only for class 2):

Y5V

5.0% 7.5% 9.0% 12.5%

Perform a heat treatment at 150+0-10°C for one hour and

then let sit for 24 ±2 hours at room temperature.

Perform initial measurement.

1000MΩ minimum or 50Ω *F

(Whichever is smaller)

Page 7

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Precaution For Handling

The multi-layer ceramic chip capacitors, may fall in a short circuit mode or in an open-circuit mode when subjected to severe

conditions of electrical, environmental and/or mechanical stress beyond the specified “Ratings” and specified “Condition” in the

Catalog and the Specifications, resulting in burnout, flaming or glowing in the worst case. So some common sense of application by

customer is necessary. Here the following article are some key points that need to take attention in application for customer reference

only:

Operating Conditions and Circuit Design

Operating temperature range

The specified “Operating Temperature Range” in the catalog is absolute maximum and minimum temperature rating. So in any case,

each the Capacitor shall be operated within the specified “Operating Temperature Range”.

Design of Voltage applications

The capacitors shall not be operated exceeding the specified “Rated Voltage” in the catalog. If voltage ratings are exceeded the

Capacitors could result in failure of damage. In case of application of DC and AC voltage to the capacitors, the designed peak voltage

shall be within the specified “Rated Voltage”.

Charging and Discharging Current

The capacitors shall not be operated beyond the specified “Maximum Charging / Discharging Current Rated” in the specification,

Application to a low impedance circuit such as a “secondary power circuit” are not recommended for safety.

Temperature Rise by Dielectric Loss of the capacitor

The “Operating Temperature Range” mentioned above shall include a maximum surface temperature rise of 20°C, which is caused by

the Dielectric loss of the Capacitor and applied electrical stress (such as voltage, frequency and wave form etc.)

It is recommended to measure and check “Surface temperature of the Capacitor” in your equipment at your estimated / designed

maximum ambient temperature.

Restriction on Environmental Conditions

The Capacitors shall not be operated and / or stored under following environmental conditions:

(a) To be exposed directly to water or salt water.

(b) To be exposed directly to sunlight.

(d) Under conditions of corrosive atmosphere such as hydrogen sulfas, sulphurous acid, chlorine, or ammonia etc.

(e) Under severe condition of vibrations or shock beyond the specified conditions in the Specifications.

Secular change in Capacitance

(1) Peculiar characteristics of “Secular Changes in Capacitance” are observed in the Capacitors (Class 2 High Dielectric Constant

Temperature Characteristics “X7R” and “Y5V”. The “secular change” shall be considered in your circuit design.

(2) The Capacitance change, due to the individual characteristics of ceramic dielectric materials applied, can be recovered to the

each initial values at shipping by a heat treatment (140 to 150°C for 1 hour).

Design of Printed Circuit Board

Selection of Printed Circuit Boards

When the Capacitors are mounted and soldered on an “Aluminium’s Substrate has influences on Capacitor’s reliability against

“Temperatures Cycles” and “Heat shock” because of difference of thermal expansion dose not deterioration the characteristics of the

Capacitors.

There are some thermal expansion factor for different kink of PC board material as follows

PC Board Material Thermal Expansion Factor (mm/°C)

1.4 x 10^-5

2.2 x 10^-5

6.5 x 10^-6

Glass Epoxy

Paper Phenol

Composite

Alumina

Page 8

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Design of Land Pattern

Recommended Dimensions of Lands. As shown in Table 1 and Figure 1.

Note:

* Too large land required excess amount of solder.

** The Dimensions shall be symmetrical.

Figure 1 Recommended Land Dimensions:

Table 1

Chip Dimensions

Land Dimension

Size

Length

Width

(L)

(W)

0603

0805

1206

1.6

2.0

3.2

0.8

1.25

1.6

0.70 ~ 1.00

1.00 ~ 1.30

2.10 ~ 2.50

0.80 ~ 1.00

1.00 ~ 1.20

1.10 ~ 1.30

0.60 ~ 0.80

0.80 ~ 1.10

1.10 ~ 1.30

Dimensions: Millimetres

Recommend amount of solder:

Recommended amount of solder: As shown in Figure2. Excess amount of solder gives large mechanical stresses to the capacitors /

Components.

Figure 2: Recommended amount of solder

Page 9

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Component Layout

When placing / mounting the capacitors / components near an area which is apt to bend or a grid groove on the PC board. It is

advisable to have both electrodes subjected to uniform stresses, or to position the component electrodes at right angles to the grid

groove or bending line.

Figure 3 Component Layout

Uneven mounting density

O: Proper

X: Improper

Probability at which the chip capacitor is broken by the stress on PC board break

A > B = C >D > E

Mounting Density and Spaces

Placements in too narrow spaces between components may cause “ Solder Bridges” during soldering. The minimum space between

components shall be 0.5mm in view of the positioning tolerances of the mounting machines and the dimensional tolerances of the

components and PC boards.

Applications of Solder Resist

Application of Solder Resist are effective to prevent solder bridges and to control amounts of solder on PC boards ( As shown in

Table 2).

Recommended Application Examples

Examples of Solder Bridges

Narrow Spacing

between Chip

Components

Radial Components

are directly

connected to

Chip Components

Common lands are

close to Chip

Components

Page 10

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Precautions for Assembly

Adhesives for Mounting

(1) Selection of adhesives

a. The viscosity of an adhesive for mountings shall be such that the adhesive dose not flow off on the land during its curing.

b. If the adhesive is too low in its viscosity, mounted components may be out of alignment after or during soldering.

c. The adhesives shall not be corrosive or chemically active to the mounted components and the PC boards.

d. The amount of adhesive shall be such that the adhesive does not flow off or be out of alignment.

e. Adhesives for mountings can be cured by ultraviolet or infrared radiation. In order to prevent the terminal electrodes of the

Capacitors the curing shall be done at conditions of 180°C maximum, for 2 minutes maximum.

Chip Mounting consideration

In mounting the Capacitors / components on a printed circuit board, any bending and expanding force against them shall be kept

minimum to prevent them from being damaged or cracked.

Following precautions and recommendation shall be observed carefully in the process:

(1) Maximum stroke of the vacuum nozzle shall be adjusted so that the pushing force to the printed circuit board shall be limited to a

static of 1 to 3 N (100 to 300 gf) (See Figure4).

(2) Maximum stroke of the nozzle shall be adjusted so that the maximum bending of printed circuit board dose not exceeded 0.5mm

(See Figure 4)

Figure 4

(3) The printed circuit board shall be supported by means of adequate supporting pins as shown in Fig.5-(b)

Figure 5

Page 11

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Soldering Flux and Solder

(1) Solder Flux:

a. The content of halogen in the soldering shall be 0.2 wt% or less.

b. Rosin-based and non-activated soldering flux is recommended.

(2) Water soluble type Soldering Flux:

In case of water soluble type soldering flux being applied, the flux residue on the surface of PC boards may have influences on the

reliability of the components and cause deterioration and failures of them.

(3) Solder:

An eutectic solder (Sn63:Pb37) is recommended.

Soldering

Since a multilayer ceramic chip capacitor comes into direct contact with melted solder during soldering. It is exposed to potentially

damaging mechanical stress caused by the sudden temperature change. The capacitor may also be subject to silver migration, and

to contamination by the flux. Because of these factors, soldering technique is critical. Adhere to the following guidelines.

Hand soldering

In hand soldering of the Capacitors, large temperature gradient between preheated the capacitors and the tip of soldering iron may

cause electrical failures and mechanical damages such as cracking of breaking of the devices. The soldering shall be carefully

controlled and carried out so that the temperature gradient is kept minimum with following recommended

conditions for hand soldering.

Recommended Soldering Conditions:

(1) Solder:

φ1mm Thread eutectic solder (Sn63:Pb37) with soldering flux *in the core.

*Rosin-based, and mom-activated flux is recommended.

(2) Preheating:

The capacitors shall be preheated so that “Temperature Gradient” between the devices and the tip of soldering iron is 150°C or

below.

(3) Soldering iron:

Rated Power of 20W Max with 3mm soldering tip in diameter.

Temperature of soldering iron tip: 300°C maximum.

(The required amount of solder shall be melted in advance on the soldering tip.)

(4)Cooling:

After soldering, the Capacitors shall cooled gradually at room ambient temperature.

Flow Soldering

In flow soldering process, abnormal and thermal and mechanical stresses, caused by “Temperature Gradient” between the mounted

Capacitors, resulting in failures and damages of the capacitors. So it is essential that the soldering process shall controlled to the

following recommended conditions and precautions. (See Figure 6)

Figure 6 Recommended Soldering Temperature Time Profile (Flow soldering)

Page 12

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

(1) Application of Flux:

The soldering flux(3.3) shall applied to the mounted Capacitors thinly and uniformly by forming method.

(2) Preheating:

The mounted Capacitors / Components shall be preheated sufficiently so that the “ Temperature Gradient” between the Capacitors /

Components and the melted solder shall be 150°C or below.

(3) Immersion to Soldering Bath:

The Capacitors shall be immersed into a soldering bath of 240 to 250°C for 3 to 5 seconds.

(4)Cooling:

The Capacitors shall be cooled gradually to room ambient temperature with the cooling temperature rates of 8°C/s maximum from

250°C to 170°C and 4°C/s maximum from 170°C to 130°C.

(5) Flux Cleaning:

When the Capacitors are immersed into cleaning solvent, it shall be confirmed that the surface temperature of devices do not exceed

100°C (See 3.5).

Reflow soldering.

I n reflow soldering process, the mounted Capacitors / Components are generally heated and Soldering by a thermal conduction

system such as an “Infrared radiation and hot blast soldering system” or a “Vapour Phase Soldering System (VPS)”, Large

temperature gradients such as a rapid heating and cooling in the process may cause electrical and mechanical damages if the

device. It is essential that the soldering process shall be controlled by following recommended conditions and precaution. (See

Figure7)

For Tin-Lead (Sn/Pb) Termination component:

(1) Preheating 1.

The mounted Capacitors / Components shall be preheated sufficiently, for 60 to 90 seconds so that the surface temperature of them

to be 140 to 150°C.

(2) Preheating 2.

After “Preheating 1”, the mounted Capacitors / Components shall be the elevated temperature of 150 to 200°C for 2 to 6 Seconds.

(3) Soldering:

The mounted Capacitors / Components shall be heated under the specified heating conditions (200 to 240 to 200°C for total 20 to 40

seconds, See Figure7 ) and shall be soldered at the maximum temperature of 240°C for 10 seconds of less.

(4)Cooling:

After the soldering, the mounted Capacitors / Components shall be gradually cooled to room ambient temperature for preventing

mechanical damages such as cracking of the devices.

(5) Flux Cleaning:

When the mounted Capacitors / Components are immersed into cleaning solvent, it shall be confirmed the surfaces temperatures of

them do not exceeding 100°C.

Note: If the mounted Capacitors / Components are partially heated in the soldering process, the devices may be separated form the

printed circuit board by the surface tension of partially melted solder, and stand up like a “Tomb Stone”.

Figure 7 Recommended Soldering Temperature Time Profile for Tin-Lead component (Reflow Soldering)

Page 13

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

For Lead-free (Pure Tin plating termination) Termination component

Essentially, the soldering temperature for Lead-free component is a little higher than that for Tin-Lead component, but need to take

consideration of the thermal effect for all other components mounting on board at the same time. The below picture is a

recommended soldering profile for Lead-free component

Figure 8 Recommended Soldering Temperature Time Profile for Lead-free component (Reflow Soldering)

Post soldering Cleaning

(1)Residues of corrosive soldering fluxes on the PC board after cleaning may greatly have influences on the electrical characteristics

and the reliability, (such as humidity resistance) of the Capacitors, which have been mounted on the board. It shall be confirmed that

the characteristic and reliability at the devices are no effected by applied cleaning conditions.

(2) Solubility of alternative cleaning solvent such as alcohol etc., is inferior to that of Freon cleaning solvent in the flux cleaning. So in

case of alternative cleaning solvents, fresh cleaning solvent shall be used, and sufficient rinsing and drying shall carried out.

(3) When an ultrasonic cleaning is applied to the mounted Capacitors on PC board, following conditions energy and the

recommended for preventing failures or damages of the devices due to the large vibration energy and the resonant caused by the

ultrasonic waves.

Frequency

Radiated Power :20 W/litre maximum.

Period :5 minutes maximum.

:29KHz maximum.

Process Inspection

When the mounted printed circuit are inspected with measuring terminal pins, abnormal and excess mechanical stresses shall not be

applied to the PC board mounted components, to prevent failure or damages of the devices.

(1) The mounted PC board shall be supported a same adequate supporting pins prevent their banding.

(2) It shall be confirmed that the measuring pin have the right tip in shape, equal in height and are set in the tight positions.

(3) The amount of adhesive shall be such that the adhesive dose flow off or be out of alignment.

Protective Coating

When the surface of a printed board on which the Capacitors has been mounted is coated with Resin to protect against moisture and

dust, it shall be confirmed that the protective coat dose not have influences on reliability of the capacitors in the actual equipment.

(1) Coating materials, such as being corrosive and chemically active, shall not be applied to the capacitors and other components.

(2) Coating materials with a large expansively shall not be applied to the Capacitors for preventing failures or damages (such as

cracking) of the devices in the curing process.

Page 14

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Dividing / Breaking of PC Boards

(1) Abnormal and excessive mechanical stresses, such as bending or expanding force on the components on the printed circuit

board, shall be kept minimum in the dividing / breaking.

(2) Dividing / Breaking of the PC board shall be done carefully at moderate speed using a Jig boards from mechanical damages.

Long Term Storage

The Capacitors shall not be stored under severe conditions of high temperatures and high humidity. Store them under 40°C

maximum and 75%RH maximum Use them within 6 months and check the solderability before use.

Part Number Table

Type

Voltage (V)

Temperature Characteristics Code

Part Number

N0603F474ZCT

N0603F474ZNT

B0603R104KCT

B0603R104KNT

T0603R223KCT

T0603R473KCT

T0603R223KNT

T0603R473KNT

T0603F104ZCT

T0603F104ZNT

U0603C220JCT

U0603C101JCT

U0603C221JCT

U0603C102JCT

U0603C100JNT

U0603C220JNT

U0603C470JNT

U0603C101JNT

U0603C221JNT

U0603C331JNT

U0603C471JNT

U0603C102JNT

U0603R102KCT

U0603R103KCT

U0603R471KNT

U0603R102KNT

U0603R222KNT

U0603R332KNT

U0603R472KNT

U0603R103KNT

U0603F103ZNT

U0603F473ZNT

0603

Page 15

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Part Number Table

Type

Voltage (V)

Temperature Characteristics Code

Part Number

N0805R105KCT

N0805R105KNT

B0805R224KCT

B0805R334KCT

B0805R474KCT

B0805R224KNT

B0805R334KNT

B0805R474KNT

T0805F105ZCT

T0805F105ZNT

U0805C102JCT

U0805C222JCT

U0805C102JNT

U0805C222JNT

U0805R102KCT

U0805R103KCT

U0805R223KCT

U0805R473KCT

U0805R104KCT

U0805R102KNT

U0805R222KNT

U0805R472KNT

U0805R103KNT

U0805R223KNT

U0805R473KNT

U0805R104KNT

U0805F104ZCT

U0805F104ZNT

A0805C100JCT

A0805C220JCT

A0805C330JCT

A0805C470JCT

A0805C101JCT

A0805C221JCT

A0805C471JCT

A0805C100JNT

A0805C220JNT

A0805C330JNT

0805

100

Page 16

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Part Number Table

Type

Voltage (V)

Temperature Characteristics Code

Part Number

A0805C470JNT

A0805C101JNT

A0805C221JNT

A0805C331JNT

A0805C471JNT

N1206R225KCT

N1206R225KNT

B1206R105KCT

B1206R105KNT

B1206F225ZCT

B1206F225ZNT

T1206C472JCT

T1206C103JCT

T1206C472JNT

T1206C103JNT

T1206R334KCT

T1206R474KCT

T1206R334KNT

T1206R474KNT

U1206R103KCT

U1206R104KCT

U1206R102KNT

U1206R222KNT

U1206R332KNT

U1206R472KNT

U1206R103KNT

U1206R223KNT

U1206R333KNT

U1206R473KNT

U1206R104KNT

B1206F475ZCT

B1206F475ZNT

A1206C100JCT

A1206C220JCT

A1206C101JCT

A1206C221JCT

A1206C331JCT

0805

100

1206

100

Page 17

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Part Number Table

Type

Voltage (V)

Temperature Characteristics Code

Part Number

A1206C471JCT

A1206C102JCT

A1206C100JNT

A1206C220JNT

A1206C330JNT

A1206C470JNT

A1206C101JNT

A1206C221JNT

A1206C331JNT

A1206C471JNT

A1206C102JNT

1206

100

Part Number Explanation

0805

102

Rated

Part

Temperature

Characteristics

Code

Capacitance

Code

Tolerance

Code

Termination

Code

Packaging

Code

Voltage

Dimension

Rated Voltage

: A, B, T and U.

Part Dimension

Temperature Characteristics Code

Capacitance Code

: 0603, 0805 and 1206.

: C, R and F.

: 100, 101, 102, 103 and 472.

: J, K and Z.

Tolerance Code

Termination Code

Packaging Code

: Termination Type.

: Packaging Type.

Page 18

27/04/06 V1.0

Nickel Barrier

Multilayer Ceramic Capacitors

Notes:

International Sales Offices:

AUSTRALIA – Farnell InOne

Tel No: ++ 61 2 9645 8888

Fax No: ++ 61 2 9644 7898

FINLAND – Farnell InOne

Tel No: ++ 358 9 560 7780

Fax No: ++ 358 9 345 5411

NETHERLANDS – Farnell InOne

Tel No: ++ 31 30 241 7373

Fax No: ++ 31 30 241 7333

SWITZERLAND – Farnell InOne

Tel No: ++ 41 1 204 64 64

Fax No: ++ 41 1 204 64 54

AUSTRIA – Farnell InOne

Tel No: ++ 43 662 2180 680

Fax No: ++ 43 662 2180 670

FRANCE – Farnell InOne

Tel No: ++ 33 474 68 99 99

Fax No: ++ 33 474 68 99 90

NEW ZEALAND – Farnell InOne

Tel No: ++ 64 9 357 0646

Fax No: ++ 64 9 357 0656

UK – Farnell InOne

Tel No: ++ 44 8701 200 200

Fax No: ++ 44 8701 200 201

BELGIUM – Farnell InOne

Tel No: ++ 32 3 475 2810

Fax No: ++ 32 3 227 3648

GERMANY – Farnell InOne

Tel No: ++ 49 89 61 39 39 39

Fax No: ++ 49 89 613 59 01

NORWAY – Farnell InOne

Tel No: ++ 45 44 53 66 66

Fax No: ++ 45 44 53 66 02

UK – BuckHickman InOne

++ 44 8450 510 150

++ 44 8450 510 130

HONG KONG

–

PORTUGAL – Farnell InOne

Tel No: ++ 34 93 475 8804

Fax No: ++ 34 93 474 5288

UK – CPC

BRAZIL – Farnell-Newark InOne

Tel No: ++ 55 11 4066 9400

Fax No: ++ 55 11 4066 9410

Farnell-Newark InOne

++ 44 8701 202 530

++ 44 8701 202 531

Tel No: ++ 852 2268 9888

Fax No: ++ 852 2268 9899

SINGAPORE

–

IRELAND – Farnell InOne

Tel No: ++ 353 1 830 9277

Fax No: ++ 353 1 830 9016

EXPORT – Farnell InOne

Tel No: ++ 44 8701 200 208

Fax No: ++ 44 8701 200 209

CHINA – Farnell-Newark InOne

Tel No: ++86 10 6238 5152

Fax No: ++86 10 6238 5022

Farnell-Newark InOne

Tel No: ++ 65 6788 0200

Fax No: ++ 65 6788 0300

export

For enquiries from all other markets

DENMARK – Farnell InOne

Tel No: ++ 45 44 53 66 44

Fax No: ++ 45 44 53 66 06

ITALY – Farnell InOne

SPAIN – Farnell InOne

Tel No: ++ 39 02 93 995 200

Fax No: ++ 39 02 93 995 300

Tel No: ++ 34 93 475 8805

Fax No: ++ 34 93 474 5107

http://www.farnellinone.com

http://www.buckhickmaninone.com

http://www.cpc.co.uk

MALAYSIA –

ESTONIA – Farnell InOne

Tel No: ++ 358 9 560 7780

Fax No: ++ 358 9 345 5411

SWEDEN – Farnell InOne

Tel No: ++ 46 8 730 50 00

Fax No: ++ 46 8 83 52 62

Farnell-Newark InOne

Tel No: ++ 60 3 7873 8000

Fax No: ++ 60 3 7873 7000

Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes

in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied.

The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data

sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage

resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded.

This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. © Premier Farnell plc 2004.

Page 19

27/04/06 V1.0

T1206C103JCT [ETC]

相关型号：

T1206C103JNT

T1206C220BCT

T1206C220CCT

T1206C220DCT

T1206C220FCT

T1206C220GCT

T1206C220JCT

T1206C472JCT

T1206C472JNT

T1206EC-3-0.00105

T1206EC-3-0.00115

T1206EC-X-0.00105