TCL150DA2-ADAL [ETC]

6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery; 6和12伏， 75至450瓦的湿电池铅钙电池


型号：	TCL150DA2-ADAL
厂家：	ETC
描述：	6 and 12 Volt, 75 to 450 Watts Wet Cell Lead Calcium Battery 6和12伏， 75至450瓦的湿电池铅钙电池电池
文件：	总2页 (文件大小：110K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

TYPE:

CATALOG NO.:

General Description

The CCL/TCL Series provides functional emer-

gency lighting in a variety of wattages up to 450

watts. High performance electronics and rugged

18 gauge steel construction ensure long-term life

safety reliability.

CCL/TCL Series

High Capacity Steel Emergency Lighting Units

6 and 12 Volt, 75 to 450 Watts

Wet Cell Lead Calcium Battery

Illumination

Illumination is accomplished with up to three

lamp heads mounted on the top of the unit. The

most popular lamp head for use with the CCL/TCL

Series is the “D” Series round sealed beam Par 36

tungsten lamp head. The “D” head is available up

to 30 watts.

Housing

Constructed of 18 gauge steel with a tan epoxy powder

coat finish.

Knockouts provided for mounting up to three lamp

heads.

Bi-color LED charge monitor/indicator and a “press-to

test” switch are located on the front of the cabinet.

Dimensions

CCL75, CCL100, CCL150, CCL225,

TCL150, TCL200

Choice of wedge base, sealed beam tungsten, or halogen

lamp heads

Shown: CCL150DL2

Electronics

Battery

Low maintenance, free electrolyte, wet cell, lead

calcium battery

6.0”

120/277 VAC dual voltage input with surge-protected,

solid-state circuitry provides for a reliable charging

system.

(15.2 cm)

Charging system is complete with low voltage

disconnect, AC lockout, brownout protection,

AC indicator lamp and test switch.

Specific gravity disk indicators show relative state

charge at a glance

12.0”

(30.5 cm)

Operating temperature range of battery is 65°F

(19°C) to 85°F (30°C)

Includes two fused output circuits.

16.0”

7.6”

(40.6 cm)

(19.3 cm)

Utilizes a fully automatic voltage regulated two-rate cur-

rent limited solid-state charger -- initially provides a high

rate charge upon restoration of AC power, and provides

trickle charge to maintain batteries at full capacity once

float voltage is attained.

Battery supplies 90 minutes of emergency power

TCL300, TCL450

Code Compliance

UL 924 listed

6.0”

(15.2 cm)

NFPA 101

Optional ACCU-TEST Self Diagnostics includes an auto-

matic 3 minute discharge test every 30 days. A manual

test is available from 1 to 90 minutes.

NEC BOCA and OSHA illumination standard

12.0”

Performance

(30.5 cm)

Input power requirements

120 VAC - 0.66 amps, 80 watts

277 VAC - 0.30 amps, 80 watts

Warranty

Three year full electronics warranty

27.0”

7.6”

(12.7 cm)

One year full plus four year prorated battery warranty

(19.3 cm)

Ordering Information

CCL

150

TD1

SERIES

WATTAGE

6 Volt

75 = 75 Watts

100 = 100 Watts

150 = 150 Watts

225 = 225 Watts

LAMP

HEADS

# OF

HEADS

3 = Three

2 = Two

1 = One

FACTORY INSTALLED

OPTIONS ¹

ACCESSORIES

CCL = 6 Volt

TCL = 12 Volt

6 Volt

A = Ammeter ²

DY = 8 Watt, Tungsten

DA = 18 Watt, Tungsten

DL = 25 Watt, Tungsten

DC = 30 Watt, Tungsten

ACF1 = 120 VAC Fuse

ACF2 = 277 VAC Fuse

LMSHELF = Mounting Shelf 300-450W

MXSHELF = Mounting Shelf 72-200W

ACP1 = 120 VAC Power Switch

ACP2 = 277 VAC Power Switch

AD = ACCU-TEST Self-Diagnostics

ADAL = ACCU-TEST with Alarm

ADTD = ACCU-TEST with Time Delay ³

DCP = DC Power Switch

12 Volt (Includes standard voltmeter) 12 Volt

150 = 150 Watt

200 = 200 Watt

300 = 300 Watt

450 = 450 Watt

DNY = 12 Watt, Tungsten

DE = 28 Watt, Tungsten

DK = 25 Watt, Tungsten

DG = 30 Watt, Tungsten

EX = Special Input Transformer (Specify voltage and frequency)

TD1 = 120 VAC Time Delay

TTD2 = 277 VAC Time Delay ³

(Suggested lamp heads listed

V = Voltmeter ²

above. Refer to the Accessories Section for

additional lamp head choices.)

W = White Housing

Notes:

1) Some option combinations may impact UL list-

ing. consult factory for specifics.

2) Not available witj AD, ADAL, or ADTD options.

3) 15 minute delay.

C1063R4

9/02 IH

Specification Data for CCL/TCL Series Steel Emergency Lighting Units

Electronics

Housing

Self-Diagnostics

120/277 VAC dual voltage input with surge-protect-

ed, solid-state charging circuitry provides for a

reliable charging system. The charging system is

furnished with low voltage disconnect, AC lockout,

brownout protection, AC indicator lamp and test

switch.

18 gauge steel housing with a tan epoxy powder coat

finish.

The ACCU-TEST Self-Diagnostics option conducts

automatic and manual tests, and indicates real time

status of the lamp, battery and charger via LED indica-

tor lamps. Automatic tests include: Systems analysis

every 10 seconds, with actual load tests performed for

a 3 minute duration every 30 days. A manual tests is

available from 1 to 90 minutes.

Knockouts provided for mounting up to three lamp

heads.

The suggested lamp head is the “D” Series round

sealed beam Par 36 tungsten. To order lamp heads

other than the suggested “D” head, refer to Chloride

Accessories Section..

The low voltage disconnect (LVD) feature will dis-

connect the battery prior to an unacceptable deep

discharge, but not before the required 90 minute

emergency operation.

Battery

Low maintenance, free electrolyte, wet cell, lead calci-

um battery.

The AC lockout feature prevents battery drain prior to

the initial energizing of utility power, and allows the

installer to complete all wiring and electrical connec-

tions without energizing the emergency circuit.

Lamp Head Photometrics

Standard sustained emergency operation is for 90

minutes with the illumination source providing full

light output.

(For DL, suggested head for CCL)

Left 30

The brownout protection circuitry will automatically

switch the unit into the emergency mode if the utility

voltage sags below 20% of nominal.

The suggested operating temperature range for lead

calcium batteries is 65°F (19°C) to 85°F (30°C) and

should provide a service life of 5 years.

feet

Battery charging circuitry is entirely solid-state, and

utilizes a fully automatic, voltage regulated charger.

Battery recharge time after full discharge is less than

the required UL 924 standard.

Performance

Right 30

Input power requirements

120 VAC - 0.66 amps, 80 watts

277 VAC - 0.30 amps, 80 watts

Up 20

Line sensitive electronics cause an instantaneous

transfer to battery power if utility power is lost, or a

brownout condition is detected. When line voltage is

present and stabilized, the transfer circuitry switches

back to normal operation and begins recharging the

battery. The transfer circuitry can be tested via a

momentary test switch located on the housing.

feet

Code Compliance

The CCL/TCL Series meets or exceeds all performance

standards as required by UL 924, NFPA 70, NFPA 101,

NEC and OSHA.

Down 20

Photometric No.

(For DK, suggested head for TCL)

Horizontal

Left 20

Operation

feet

Suggested

Lamp Head

Watts to 87 ⁄

Voltage

Unit

of Rated Voltage*

1 ⁄

hrs. 2 hrs. 4 hrs. 8 hrs.

Right 20

CCL75

28.5 15

38 20

CCL100

CCL150

CCL225

TCL150

TCL200

TCL300

TCL450

100

150

225

150

200

300

450

Vertical

Up 20

112.5 57 30

169 85.5 45

112.5 57 30

96 34

114 60

337.5 171 90

feet

150

225

Down 20

Suggested Specification

Furnish and install Chloride Systems emergency lighting unit model ________. The unit shall be constructed to meet Underwriter’s Laboratories, Inc. Standard #924

and the National Electrical Code (NEC).

INSTALLATION AND OPERATION - Unit shall be easily field connected to a 120 or 277 VAC, 60 hertz, unswitched power source. Installation must comply with the

NEC as well as other applicable codes. Upon utility power failure or brownout, the unit shall automatically transfer to battery power and maintain the required illumina-

tion level for a minimum period of 90 minutes. Upon restoration of utility power, the charger shall restore the battery to full charge within UL 924 requirements follow-

ing a rated discharge of not more than 90 minutes.

CHARGER - Product shall utilize a fully automatic, voltage regulated, two-rate current limited solid-state charger. The charging system shall maintain the battery at

full capacity without the need for periodic exercising or equalization. The following features shall be standard: Low voltage disconnect (LVD), brownout protection and

AC lockout.

BATTERY - The battery shall be a low maintenance, free electrolyte, wet cell, lead calcium battery. The lead calcium battery shall provide trouble-free operation in

temperatures up to 85°F (30°C).

HOUSING - The unit housing shall be constructed of 18 gauge steel with a tan epoxy powder coat finish.

272 West Stag Park Service Road • Burgaw NC 28425

Telephone: (910) 259 1000 • Facsimile: (800) 258 8803

www.chloridesys.com

A2528

ISO 9001

C1063R4

9/02 IH

Chloride Systems