TSC-075S140ST [ETC]
Dimmable LED Drivers;
| 型号： | TSC-075S140ST |
| 厂家： | 
ETC |
| 描述： | Dimmable LED Drivers |
| 文件： | 总3页 (文件大小：660K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSC-75W Series
Dimmable LED Drivers
Constant Current
Aluminum Housing
Electrical Specifications
Input Voltage Range:
277 - 480 Nom. Vac (249 - 528 V Min/Max)
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
>0.90 @ full load, 277V through 480V
Power Factor:
Inrush Current:
Input AC Current:
Maximum Power:
Line Regulation:
Load Regulation:
THD:
135.0 Amps max @ 480 Vac, cold start 25ºC
0.34 A max 277VAC, 0.21 A max 480Vac
75W
± 1%
± 3%
<_ 20% @ full load
0.7 mA 480 Vac 50Hz
85-87% at 480Vac
1 S typical
20%
Leakage Current:
Typical Efficiency
Turn-on Delay:
Output Current Ripple:
Output Protection:
• Total Power: 75 Watts
• Input Voltage: 277-480 Vac Nom.
• UL Dry, Damp & Wet Location Rated
• IP67
Over-Voltage, Over-Temperature,
and Short Circuit Protection
• High Power Factor
• UL Type HL Rated
* UL8750
Environmental Specifications
Minimum Starting Temp: -40ºC
Maximum Case Temp.
Storage Temperature:
Humidity:
90°C
-40ºC to +85ºC
5% to 100%
Convection
Class A
Cooling:
Sound Rating:
MTBF:
380,000 Hours (700 mA model) at 480Vac input, 80%
load and 25ºC ambient conditions per MIL-HDBK-217F
Lifetime:
Weight:
50,000 Hours @ Case Temperature = 60ºC
2.2 lbs. (1.0 kg)
Constant Current - Product Specifications
Output Current Output Voltage
Max. Output
Power (W)
Typical
Efficiency
Model Number
(mA ±5%)
Range (Vdc)
107-214
53-107
36-72
TSC-075S035ST
TSC-075S070ST
TSC-075S105ST
TSC-075S140ST
TSC-075S210ST
TSC-075S315ST
350
75
75
75
75
75
75
87%
86%
87%
87%
86%
85%
700
1050
1400
2100
3150
26-53
18-36
12-24
Dimming Versions - Product Specifications
Output Current Output Voltage
Max. Output
Power (W)
Typical
Efficiency
Model Number
(mA ±5%)
Range (Vdc)
107-214
53-107
36-72
TSC-075S035DT
TSC-075S070DT
TSC-075S105DT
TSC-075S140DT
TSC-075S210DT
TSC-075S315DT
350
75
75
75
75
75
75
87%
86%
87%
87%
86%
85%
700
1050
1400
2100
3150
26-53
18-36
12-24
E332160
The output current is adjustable at factory from 50% to 100%.
Class 2:
US/Canada
US Only
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 8-31-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com
TSC 75W Series
SSL Solutions Faster Than The Speed Of Light®
Pg 2 of 3
Dimensions - mm
222
188
184
38.1
15
DC OUPUT (2*AWG18)
Red (V+)
AC INPUT (3*AWG18)
Black (ACL)
Blue (V-)
220±20
White (ACN)
Green (GND)
50±5
Tc = 90°C max
50±5
30±2
40±2
50±2
650±20
115
230±20
Dimming Control (3*AWG22)
Purple (Dim+)
Gray (Dim-)
Black/White (VC)
202
4.4
Ø9.5
Derating Curve
Lifetime / Case Temperature
135
120
105
90
75
60
45
30
15
0
100
80
60
40
20
0
-10
0
10
20
30
40
50
60
70
30 35 40 45 50
60 65
75 80 85 90
Case T5e5mperatur7e0(°C)
Ambient Temperature (°C)
Efficiency / Load
350mA Model
Power Factor / Output Voltage
95%
90%
85%
80%
75%
70%
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
277 Vac
480 Vac
277 Vac
480 Vac
50%
60%
70%
80%
90%
100%
50%
60%
70%
80%
90%
100%
Normalized Output Voltage
Normalized Output Voltage
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com
TSC 75W Series
SSL Solutions Faster Than The Speed Of Light®
Pg 3 of 3
Dimming Control
Parameters
12V output voltage
Minimum
10.8 V
10 mA
-2 V
Typical
12 V
Maximum
13.2 V
Vc source current
15 mA
—
20 mA
Absolute maximum voltage on the 0~10V input pin
Source current on 0~10V input pin
15 V
150 µA
200 µA
250 µA
The dimmer control is operated from an input signal of 1 – 10 Vdc.
Implementation with 0-10V Dimming
Output Current/Dimming Voltage
V+ (Red)
Vac
100%
80%
60%
40%
20%
0%
L
V- (Blue)
Vc (Black/White)
Dim+ (Purple)
N
G
TSC-75xxxDT
0-10V
Dimmer
Dim- & Vc Return
(Gray)
0
1
2
3
4
5
6
7
8
9
10
Dimming Voltage (V)
Notes:
1. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like resistors and zener.
2. The dimming signal is allowed to be less than 1V, when it is between 0 and 1V, the output level is 10%.
3. Do NOT connect the Gray Wire (Vdim-) to Blue Wire (V-) together.
4. The dimming section is not isolated from the output.
5. Vc is an auxillary 12V/15mA output.
6. If 0-10V dimming is not used, Dim+ can be either capped-off or connected to Vc.
Safety
Standard
Certification
UL/CUL
CE
UL8750, UL1310, UL1012, CAN/CSA-C22.2 No. 223-M91, CSA-C22.2 No. 107.1-01
EN 61347-1, EN61347-2-13
EMC Standard Notes
EN 55015
Conducted emission Test & Radiated emission Test with 6 dB margin
EN 61000-3-2
EN 61000-3-3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
EN 61547
Harmonic current emissions: Class C
Voltage fluctuations & flicker
Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge Level 3, Criteria A
Radio-Frequency Electromagnetic Field Susceptibility Test-RS Level 3, Criteria A
Electrical Fast Transient / Burst-EFT Level 3, Criteria A
Surge Immunity Test: AC Power Line: line to line 4kV, line to earth 6 kV
Conducted Radio Frequency Disturbances Test-CS Level 3, Criteria A
Power Frequency Magnetic Field Test 3A/m , Criteria A
Voltage Dips Criteria B
Electromagnetic Immunity Requirements Applies To Lighting Equipment
Note:
Disconnect power to LED driver for at least 30 seconds before connecting or disconnecting Driver output and LED Engine. This prevents potential arcing transients
that can damage the Engine and Driver. See Hot Plugging in our Driver Application Guide for more information.
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com
相关型号：
TSC-101.6OHM5%BKTS
Fixed Resistor, Wire Wound, 10W, 1.6ohm, 1000V, 5% +/-Tol, -260,260ppm/Cel
VISHAY
©2020 ICPDF网 联系我们和版权申明