XL6007E1 [ETC]

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter;
XL6007E1
型号: XL6007E1
厂家: ETC    ETC
描述:

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

文件: 总8页 (文件大小:157K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Features  
General Description  
n Wide 3.6V to 24V Input Voltage Range  
n Positive or Negative Output Voltage  
Programming with a Single Feedback Pin  
n Current Mode Control Provides Excellent  
Transient Response  
The XL6007 regulator is a wide input range,  
current mode, DC/DC converter which is  
capable of generating either positive or  
negative output voltages. It can be configured  
as either a boost, flyback, SEPIC or inverting  
converter. The XL6007 built in N-channel  
power MOSFET and fixed frequency  
oscillator, current-mode architecture results in  
stable operation over a wide range of supply  
and output voltages.  
n 1.25V reference adjustable version  
n Fixed 400KHz Switching Frequency  
n Maximum 2A Switching Current  
n SW PIN Built in Over Voltage Protection  
n Excellent line and load regulation  
n EN PIN TTL shutdown capability  
n Internal Optimize Power MOSFET  
The XL6007 regulator is special design for  
portable electronic equipment.  
n
High efficiency up to 90%  
n Built in Frequency Compensation  
n Built in Soft-Start Function  
n Built in Thermal Shutdown Function  
n Built in Current Limit Function  
n
Available in SOIC-8 package  
Applications  
n Automotive and Industrial Boost  
Buck-Boost / Inverting Converters  
n Portable Electronic Equipment  
/
Figure1. Package Type of XL6007  
Rev 1.2  
www.xlsemi.com  
1
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Pin Configurations  
EN  
1
8
GND  
2
3
7
6
GND  
SW  
VIN  
FB  
XL6007  
4
5
SW  
NC  
Figure2. Pin Configuration of XL6007 (Top View)  
Table 1 Pin Description  
Pin Number Pin Name Description  
Enable Pin. Drive EN pin low to turn off the device, drive it  
high to turn it on. Floating is default high.  
Supply Voltage Input Pin. XL6007 operates from a 3.6V to 24V  
DC voltage. Bypass Vin to GND with a suitably large capacitor  
to eliminate noise on the input.  
1
2
EN  
VIN  
3
4
FB  
NC  
Feedback Pin (FB). The feedback threshold voltage is 1.25V.  
No Connected.  
Power Switch Output Pin (SW). Output is the switch node that  
supplies power to the output.  
Ground Pin.  
5,6  
7,8  
SW  
GND  
Rev 1.2  
www.xlsemi.com  
2
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Function Block  
Figure3. Function Block Diagram of XL6007  
Typical Application Circuit  
Figure4. XL6007 Typical Application Circuit (Boost Converter)  
Rev 1.2  
www.xlsemi.com  
3
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Ordering Information  
Part Number  
Lead Free  
Marking ID  
Lead Free  
Packing Type  
Temperature  
Package  
Range  
XL6007E1  
XL6007TRE1  
XL6007E1  
XL6007E1  
Tube  
Tape & Reel  
XLSEMI Pb-free products, as designated with E1suffix in the par number, are RoHS compliant.  
Absolute Maximum RatingsNote1)  
Parameter  
Symbol  
Vin  
Value  
-0.3 to 26  
Unit  
V
Input Voltage  
Feedback Pin Voltage  
-0.3 to Vin  
-0.3 to Vin  
-0.3 to 60  
V
VFB  
EN Pin Voltage  
V
VEN  
Output Switch Pin Voltage  
Power Dissipation  
V
VOutput  
PD  
Internally limited  
mW  
Thermal Resistance (SOP-8L)  
(Junction to Ambient, No Heatsink, Free Air)  
Operating Junction Temperature  
Storage Temperature  
100  
ºC/W  
RJA  
-40 to 125  
-65 to 150  
260  
ºC  
ºC  
ºC  
V
TJ  
TSTG  
TLEAD  
Lead Temperature (Soldering, 10 sec)  
ESD (HBM)  
>2000  
Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage  
to the device. This is a stress rating only and functional operation of the device at these or any  
other conditions above those indicated in the operation is not implied. Exposure to absolute  
maximum rating conditions for extended periods may affect reliability.  
Rev 1.2  
www.xlsemi.com  
4
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
XL6007 Electrical Characteristics  
Ta = 25;unless otherwise specified.  
Symbol  
Parameter  
Test Condition  
Min. Typ. Max. Unit  
System parameters test circuit figure4  
Feedback  
Voltage  
Vin = 12V to 16V, Vout=18V  
VFB  
1.213 1.25 1.287  
90  
V
Iload=0.1A to 0.5A  
Vin=12V ,Vout=18.5V  
Iout=0.5A  
Efficiency  
-
-
%
ŋ
Electrical Characteristics (DC Parameters)  
Vin = 12V, GND=0V, Vin & GND parallel connect a 220uf/50V capacitor; Iout=0.5A, Ta =  
25; the others floating unless otherwise specified.  
Parameters  
Symbol  
Vin  
Test Condition  
Min. Typ. Max. Unit  
Input operation voltage  
Shutdown Supply Current  
3.6  
24  
V
ISTBY  
VEN=0V  
70  
100  
uA  
VEN =2V,  
VFB =Vin  
Quiescent Supply Current  
Iq  
2.5  
5
mA  
Oscillator Frequency  
Switch Current Limit  
Fosc  
IL  
320  
400  
2
480  
Khz  
A
VFB =0  
Vin=12V,  
ISW=2A  
Output Power NMOS  
EN Pin Threshold  
Rdson  
VEN  
110  
120 mohm  
High (Regulator ON)  
Low (Regulator OFF)  
1.4  
0.8  
V
IH  
IL  
VEN =2V (ON)  
VEN =0V (OFF)  
3
3
10  
10  
uA  
uA  
EN Pin Input Leakage  
Current  
Max. Duty Cycle  
DMAX  
VFB=0V  
90  
%
Rev 1.2  
www.xlsemi.com  
5
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Schottky Diode Selection Table  
Current Surface Through VR (The same as system maximum input voltage)  
Mount Hole  
20V  
30V  
40V  
50V  
60V  
1N5817  
1N5818  
1N5819  
1A  
3A  
1N5820  
MBR320  
SK32  
1N5821  
MBR330  
SK33  
1N5822  
MBR340 MBR350  
SK34 SK35  
MBR360  
SK36  
30WQ03  
31DQ03  
SR303  
30WQ04 30WQ05  
31DQ04 31DQ05  
SR302  
SR304  
SR305  
SR306  
Typical System Application Boost (Output 18.5V/0.5A)  
Figure5. XL6007 Typical System Application (Boost Converter)  
Rev 1.2  
www.xlsemi.com  
6
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Typical System Application SEPIC Buck-Boost (Input 10V~18V, Output 12V/0.5A)  
Figure6. XL6007 Typical System Application (SEPIC Buck-Boost Converter)  
Typical System Application for Inverting Converter  
SEPIC Inverting Topology (Input 10V~18V, Output + -12V/0.6A)  
Figure7. XL6007 Typical System Application (SEPIC Inverting Converter)  
Rev 1.2  
www.xlsemi.com  
7
XL6007  
400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter  
Package Information  
SOP8 Package Mechanical Dimensions  
Rev 1.2  
www.xlsemi.com  
8

相关型号:

XL6007TRE1

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
ETC

XL6008

升压型直流电源变换器芯片15W方案
ETC

XL6008E1

400KHz 60V 3A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
ETC

XL6008TRE1

400KHz 60V 3A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
ETC

XL6009

400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
XLSEMI

XL6009E1

400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
XLSEMI

XL6009TRE1

400KHz 60V 4A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
XLSEMI

XL6013E1

400KHz 60V 2A Switching Current Boost LED Constant Current Driver
ETC

XL6019E1

220KHz 60V 5A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter
ETC