ZVT-2 [ETC]
TEMPERATURE CONTROLLER 240VAC ; 温度控制器240VAC\n型号: | ZVT-2 |
厂家: | ETC |
描述: | TEMPERATURE CONTROLLER 240VAC
|
文件: | 总2页 (文件大小:64K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ZVT 16 AMP 0-150°C
TEMPERATURE CONTROLLER
AND SENSOR
ZVT
INSTALLATION
INSTALLATION
X10234
INSTALLATION
1. Peel adhesive back off dial and fit over 10mm panel hole.
2. See the table below for heatsink requirements & expected ambient temperature, to calculate the
maximum current rating.
3. Check that the voltage rating & sensor type is correct.
4. Insert unit through 10mm panel hole, dial and extra heatsink as appropriate, ensuring
equipotential bonding (Earth bonding) and tighten front nut. Use a ‘thin smear’ of heatsink
paste for good thermal coupling.
5. Before fitting knob, turn temperature control fully anti-clockwise to the mechanical stop.
6. Fit and align knob to coincide with the dial mark below 0ºC
7. Make wire connections to rear terminals. To monitor supply and load conditions fit neon’s
across the relevant terminals.
MAXIMUM OUTPUT RMS CURRENT (A)
20ºC
50ºC 65ºC
Max. ambient temperature
Without extra heatsink
10
7
5
+ Heatsink 100 x 100 x 3mm 14
+ Heatsink 170 x 170 x 3mm
12
10
OPERATION
8. Note that unit will not operate or indicate correctly with loads of less than 200W, to ensure triac
latches on.
9. Set Prop. Band (via rear panel) fully anti-clockwise
10. Switch and turn dial to required temperature and allow system to heat up to a steady state. If
temperature is unstable turn Prop. Band clockwise in small steps over several minutes until
stable conditions are obtained, characterised by a steady output On/Off ratio
11. If output remains off, check for open or short circuit in sensor circuit, and if output stays on,
check position of sensor relative to heated zone. Correct sensor resistance is 10.7K @ 0ºC, 10K
@ 25ºC, 7.9K @ 100ºC.
12. Do not use Megger or other high voltage equipment as the voltage rating may be exceeded and
damage the internal components.
FUSING
It is recommended to use semiconductor fast acting type fuses and circuit breakers (Semiconductor-
MCB) for unit protection. (See SRA Datasheet for further information).
CE MARKING
This product family carries a “CE marking” . For information see recommendation section and
contact our sales desk.
INTRODUCTION
The ZVT-E sensor is a NTC resistor sealed in a stainless steel probe with 1M PTFE tails and earth
lead.
APPLICATIONS
Use with ZVT temperature controller (See Recommendations Datasheet X10211).
INSTALLATION, DIMENSIONS AND SPECIFICATIONS
NOTE: THIS SENSOR MUST
BE EARTHED
RECOMMENDATION
Other documents available on request, which may be appropriate for your applications.
CODE
IDENTITY DESCRIPTION
X10211 ZVT
X10213 ITA
X10255 SRA
16A Temperature controller
Interaction, uses for phase angle and for burst fire control.
Safety requirements - addressing the Low Voltage Directive (LVD)
including :- Thermal data/cooling ; “Live” parts warning & Earth
requirements; Fusing recommendations.
AP02/4
COS
UAL Conditions of sale
NOTE It is recommended that installation and maintenance of this equipment should be done
with reference to the current edition of the I.E.E. wiring regulations (BS7671) by suitably
qualified/trained personnel. The regulations contain important requirements regarding safety of
electrical equipment. (For international standards refer to I.E.C. directive I.E.C. 950).
ORDER CODE:
State part number: ZVT ‘E’ SENSOR FOR ENCLOSED.
UNITED AUTOMATION LIMITED
1 Southport Business Park
Southport, PR8 4HQ, U.K.
Tel (01704)-565713
Fax (01704)-569760
Page No 2 of 2 Issue 1 16/10/97
相关型号:
ZW-01-07-F-D-214-064
Board Stacking Connector, 2 Contact(s), 2 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT
SAMTEC
ZW-01-07-F-Q-200-055
Board Stacking Connector, 2 Contact(s), 2 Row(s), Male, Straight, Solder Terminal
SAMTEC
ZW-01-07-F-S-200-055
Board Stacking Connector, 1 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
SAMTEC
ZW-01-07-FM-S-200-055
Board Stacking Connector, 1 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
SAMTEC
ZW-01-07-G-D-200-064
Board Stacking Connector, 2 Contact(s), 2 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT
SAMTEC
ZW-01-07-G-D-374-056
Board Stacking Connector, 2 Contact(s), 2 Row(s), Male, Straight, Solder Terminal, ROHS COMPLIANT
SAMTEC
ZW-01-07-G-Q-200-055
Board Stacking Connector, 2 Contact(s), 2 Row(s), Male, Straight, Solder Terminal
SAMTEC
ZW-01-07-G-S-100
Board Stacking Connector, 1 Contact(s), 1 Row(s), Male, Straight, Solder Terminal
SAMTEC
ZW-01-07-G-S-200-150
Board Stacking Connector, 1 Contact(s), 1 Row(s), Male, Straight, Solder Terminal,
SAMTEC
©2020 ICPDF网 联系我们和版权申明