333/Y5C1-ATWB/MS [EVERLIGHT]
Single Color LED, Brilliant Yellow, Water Clear, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2;
| 型号： | 333/Y5C1-ATWB/MS |
| 厂家： | 
EVERLIGHT ELECTRONICS CO., LTD |
| 描述： | Single Color LED, Brilliant Yellow, Water Clear, T-1 3/4, 5mm, ROHS COMPLIANT, PLASTIC PACKAGE-2 光电 |
| 文件： | 总10页 (文件大小：100K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Technical Data Sheet
333/Y5C1-ATWB/MS
Features
˙Popular T-1 3/4 round package.
˙Choice of various viewing angles.
˙Available on tape and reel.
˙Reliable and robust.
˙UV resistant epoxy
˙The product itself will remain within RoHS compliant version.
Descriptions
˙The series is specially designed for
applications requiring higher
brightness.
˙The LED lamps are available with
different colors,intensities,epoxy
colors, etc.
Applications
˙Color Graphic Signs
˙Message boards
˙Variable message signs (VMS)
˙Commercial outdoor advertising
Device Selection Guide
Chip
Lens Color
Material
Emitted Color
AlGaInP
Brilliant Yellow Water clear
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 1 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Package Dimensions
Notes:
˙All dimensions are in millimeters, tolerance is 0.25mm except being specified.
˙Protruded resin under flange is 1.5mm Max LED.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 2 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
IF
Rating
50
Units
mA
mA
℃
Forward Current
Pulse Forward Current*1
Operating Temperature
Storage Temperature
Electrostatic Discharge
Soldering Temperature*2
Power Dissipation
IFP
160
Topr
Tstg
ESD
Tsol
Pd
-40 ~ +85
-40 ~ +100
2K
℃
V
℃
260
115
mW
V
Reverse Voltage
VR
5
Notes: *1:IFP Conditions--Pulse Width≦10msec and Duty≦1/10.
*2:Soldering time≦5 seconds.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Forward Voltage
Luminous Intensity
Viewing Angle
Symbol Condition
Min.
1.8
7150
--
Typ.
2.0
--
Max.
2.6
18000
--
Units
V
VF
IV
IF=20mA
IF=20mA
IF=20mA
IF=20mA
IF=20mA
IF=20mA
VR=5V
mcd
deg
nm
2θ1/2
λp
15
Peak Wavelength
Dominant Wavelength
--
591
589
15
--
λd
586
--
594
--
nm
Spectrum Radiation
Bandwidth
Δλ
IR
nm
μA
Reverse Current
--
--
10
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 3 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Rank Combination (IF=20mA)
Rank
T
U
V
W
Luminous Intensity
7150~9000
9000~11250 11250~14250 14250~18000
*Measurement Uncertainty of Luminous Intensity: ±10%
Unit: :mcd
Rank
1
2
3
4
Forward Voltage
1.8~2.0
2.0~2.2
2.2~2.4
2.4~2.6
Unit: V
*Measurement Uncertainty of Forward Voltage: ±0.1V
Rank
1
2
Dominant Wavelength
586~590
590~594
*Measurement Uncertainty of Dominant Wavelength ±1.0nm
Unit: nm
*The quantity ratio of the ranks is decided by EVERLIGHT.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 4 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 5 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Packing Specification
■ Anti-electrostatic bag
EVERLIGHT
Label
CPN:
P/N:XXXXXXXXXX
RoHS
XXX/XXXX-XXXX
Pb
QTY：XXXX
ELꢀECTROSTATICꢀELECTRONAGNETICꢀ
MAGNETICꢀORꢀRADIOACTIVEꢀRELDS
CAT:XX
anti-staticꢀforꢀ750
HUE:XX
REF:XX
XXXXXXXX
LOT NO：
■ Inner Carton
MADE IN TAIWAN
■ Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks of Luminous Intensity and Forward Voltage
HUE: Rank of Dominant Wavelength
REF: Reference
■ Outside Carton
LOT No: Lot Number
MADE IN TAIWAN: Production Place
■ Packing Quantity
1. 500 PCS/1 Bag，5 Bags/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 6 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Notes
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of
the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may
damage the LED’s characteristics or it may break the LEDs.
Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures
may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the
lead position of the LED. If the LEDs are mounted with stress at the leads, it causes
deterioration of the epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from
Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or
more, they can be stored for a year in a sealed container with a nitrogen atmosphere and
moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity
environments where condensation can occur.
3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm
from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is
recommended.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 7 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Recommended soldering conditions:
Hand Soldering
DIP Soldering
300℃ Max. (30W
Max.)
100 ℃ Max. (60 sec
Temp. at tip of iron
Preheat temp.
Max.)
Soldering time
Distance
3 sec Max.
Bath temp. & time 260 Max., 5 sec Max
3mm Min.(From solder Distance
joint to epoxy bulb)
3mm Min. (From solder
joint to epoxy bulb)
Recommended soldering profile
laminar wave
Fluxing
Prehead
Avoiding applying any stress to the lead frame while the LEDs are at high temperature
particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or
vibration until the LEDs return to room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak
temperature.
Although the recommended soldering conditions are specified in the above table, dip or
handsoldering at the lowest possible temperature is desirable for the LEDs.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 8 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
Wave soldering parameter must be set and maintain according to recommended
temperature and dwell time in the solder wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room
temperature for a duration of no more than one minute. Dry at room temperature before
use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence
of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the
assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not
cause damage to the LED
5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of
LED application. The current should be de-rated appropriately by referring to the
de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please
refer to the data sheet de-rating curve.
6. ESD (Electrostatic Discharge)
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever
handling LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of
the LEDs plastic lens as a result of friction between LEDs during storage and handing.
7. Other
Above specification may be changed without notice. EVERLIGHT will reserve
authority on material change for above specification.
When using this product, please observe the absolute maximum ratings and the
instructions for using outlined in these specification sheets. EVERLIGHT assumes no
responsibility for any damage resulting from use of the product which does not comply
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 9 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
Technical Data Sheet
333/Y5C1-ATWB/MS
with the absolute maximum ratings and the instructions included in these specification
sheets.
These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date: 05-09-2009
Rev 1
Page: 10 of 10
Device Number : DLE-0001403
Prepared : Flourix Chen
相关型号：
©2020 ICPDF网 联系我们和版权申明