3474AN/BADB-AGJA/PR/MS [EVERLIGHT]
Single Color LED,;
| 型号： | 3474AN/BADB-AGJA/PR/MS |
| 厂家： | 
EVERLIGHT ELECTRONICS CO., LTD |
| 描述： | Single Color LED, |
| 文件： | 总12页 (文件大小：429K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Features
• High lumin
• Oval Shap
• Well define
• Wide view
• UV resista
• The produ
•Complianc
•Compliance
Description
• This precision optical performance oval LED is specifically designed for passenger information signs.
• This lamp has matched radiation patterns with red, yellow or green mixing color applications.
Applications
• Color Graphic Signs
• Message boards
• Variable message signs (VMS)
• Commercial outdoor advertising
1
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Device Selection Guide
LED Part No.
Chip Materials
InGaN
Emitted Color
Blue
Resin Color
Water Clear
Stopper
3474AN/BADB-AGJA/R/MS
3474AN/BADB-AGJA/PR/MS
No
Yes
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
5
Reverse Voltage
Forward Current
VR
IF
V
30
mA
Peak
(Dut
Pow
Opera
Stora
Solde
2
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Iv
2θ1/2
λp
mcd
deg
nm
nm
nm
V
IF=20mA
IF=20mA
IF=20mA
IF=20mA
IF=20mA
IF=20mA
VR=5V
Luminous Intensity
Viewing Angle
720
--
--
1450
--
X:110 Y:50
Peak Wavelength
--
468
--
--
λd
Dominant Wavelength
Spectrum Radiation Bandwidth
Forward Voltage
465
--
475
--
Δλ
26
--
VF
IR
2.8
--
3.6
50
μA
Reverse Current
--
Bin Range of Luminous Intensity
Condition
IF =20mA
Note:
Tolerance of L
Bin Rang
nm
Condition
IF =20mA
1a
1b
2a
2b
465.0
467.5
470.0
472.5
467.5
470.0
472.5
475.0
Note:
Tolerance of Dominant Wavelength: ±1nm
Bin Range of Forward Voltage
Bin Code
Min.
Max.
Unit
V
Condition
IF =20mA
0
1
2
3
2.8
3.0
3.2
3.4
3.0
3.2
3.4
3.6
Note:
Tolerance of Forward Voltage: ±0.1V
3
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Typical Electro-Optical Characteristics Curves
Directivity (Ta=25℃)
Relative Intensity vs. Wavelength (Ta=25℃)
1.0
0.8
0.6
0.4
0.2
0.0
350
400
450
500
550
600
Wavelength (nm)
Relative Intensity (a.u.)
Forward Current vs. Forward Voltage (Ta=25℃)
Relative Intensity vs. Forward Current (Ta=25℃)
25
20
15
10
5
0
25
1.
Forward Voltage (V)
Forward Current (mA)
Relative Intensity vs. Ambient Temp.
Forward Current vs. Ambient Temp.
2.0
40
1.5
1.0
0.5
0.0
30
20
10
0
25
30
35
40
45
50
55
60
65
70
0
20
40
60
80
100
Ambient Temperature Ta(℃)
Ambient Temperature Ta(℃)
4
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Package Dimension
Stopper Type
No Stopper Type
Note:
˙All dimensions are in millimeters, tolerance is 0.25mm except being specified.
˙Protruded resin under flange is 1.5mm Max LED.
Moisture Resistant Packing Materials
5
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Label Explanation
‧CPN: Customer’s Product Number
‧P/N: Product Number
‧QTY: Packing Quantity
‧CAT: Ranks of Luminous Intensity
‧HUE: Ranks of Dominant Wavelength
‧REF: Ranks of Forward Voltage
‧LOT No: Lot Number
Carrier Tape
6
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Taping Sizes
Specifications
Avg.
Symbol Items
Symbol
Tolerance
(mm)
±0.2
mm
4.00
2.54
2.0
Inch
0.157
0.100
0.078
Tape Feed Hole Diameter
D
F
Component Lead Pitch
±0.3
Front-to-Read Deflection
Feed Hole to Button of Component
Feed Hole to Overall Component Height
Lead Length after Component Removal
Feed Hole Pitch
△
H
Max
±1.0
H1
18.5
24.6
0.729
0.969
H2
L
±1.0
11.00
12.70
0.433
0.500
Max
±0.3
P
Lead Location
Center of Compo
Overall Taped Pa
Feed Hole Locati
Adhesive Tape W
Adhesive Tape Po
Tape Width
7
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Moisture Resistant Packing Process
■
Packing Quantity
1. 2500 PCS/1 Inner Carton
■
Inner Carton
2. 10Inner Cartons/1 Outside Carton
■
Outside Carton
8
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Production Designation
3474AN / B A D B- □ □ □ □
Voltage Group
Luminous Intensity Bins
Wave Group
Viewing Angle
Color Lens
Color
Product name
Notes
1. Lead Formi
Durinoxy bulb.
Lead
Avoid age the LED’s
char
Cut tcause failure of
the L
Whetion of the LED.
If the his will degrade
the L
2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and
the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored
for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments
where condensation can occur.
3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,
and soldering beyond the base of the tie bar is recommended.
9
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
Recommended soldering conditions:
Hand Soldering
DIP Soldering
100℃ Max. (60 sec
300℃ Max. (30W
Temp. at tip of iron
Max.)
Preheat temp.
Max.)
Soldering time
Distance
3 sec Max.
Bath temp. & time
Distance
260 Max., 5 sec Max
3mm Min. (From solder
joint to epoxy bulb)
3mm Min.(From
solder joint to epoxy
bulb)
Recommended soldering profile
laminar wave
Fluxing
Avoidicularly when
solde
Dip a
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the
LEDs return to room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the
lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time
in the solder wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no
more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning
on the LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning
shall be pre-qualified to ensure this will not cause damage to the LED
10
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED application. The
current should be de-rated appropriately by referring to the de-rating curve found in each product
specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet
de-rating curve.
6. ESD (Electrostatic Discharge)
The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly
recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surg
If too
the fo
7. Directions
The the LEDs are
not sapplied to the
LEDs, it may cause migration resulting in LED damage.
8. Other
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for
above specification.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined
in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of
the product which does not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please
don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
11
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
DATASHEET
Oval Lamp
3474AN/BADB-AGJA/XR/MS
DISCLAIMER
1.
2.
3.
4.
EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification.
The product meets EVERLIGHT published specification for a period of twelve (12) months from date of shipment.
The graphs shown in this datasheet are representing typical data only and do not show guaranteed values.
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in
these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the
product which does not comply with the absolute maximum ratings and the instructions included in these
specification sheets.
5.
6.
These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is
prohibited without obtaining EVERLIGHT’s prior consent.
This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving
applications or any other application which can result in human injury or death. Please contact authorized Everlight
sales agent for special application request.
12
Copyright © 2010, Everlight All Rights Reserved. Release Date : Nov.16. 2016. Issue No: DLE-0007908_Ver.3
www.everlight.com
Ver.: Release Date: Confidential Level: 狀態:
ꢀ
相关型号：
3474AN/GADB-AKMA/PR/MS
Single Color LED, Brilliant Green, Diffused Green, 3.95mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/GADB-AKMA/R/MS
Single Color LED, Brilliant Green, Diffused Green, 3.95mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/GADB-AMNA/MS
Single Color LED, Brilliant Green, Diffused Green, 3.95mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
EVERLIGHT
3474AN/GADB-AMNA/P/MS
Single Color LED, Brilliant Green, Diffused Green, 3.95mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
EVERLIGHT
3474AN/R3DB-AFGC/PR/MS
Single Color LED, Brilliant Red, Diffused Red, 3mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/R3DB-AFGC/R/MS
Single Color LED, Brilliant Red, Diffused Red, 3mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/R3DB-AGHC/PR/MS
Single Color LED, Brilliant Red, Diffused Red, 3.95mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/R3DB-AGHC/R/MS
Single Color LED, Brilliant Red, Diffused Red, 3.95mm, ROHS COMPLIANT PACKAGE-2
EVERLIGHT
3474AN/R7DB-AHJB/MS
Single Color LED, Brilliant Red, Diffused Red, 3.95mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
EVERLIGHT
©2020 ICPDF网 联系我们和版权申明