5484BN/GADC-AMNA/MS [EVERLIGHT]
Single Color LED, Brilliant Green, Diffused Green, 5.2mm, ROHS COMPLIANT, PLASTIC PACKAGE-2;
| 型号： | 5484BN/GADC-AMNA/MS |
| 厂家： | 
EVERLIGHT ELECTRONICS CO., LTD |
| 描述： | Single Color LED, Brilliant Green, Diffused Green, 5.2mm, ROHS COMPLIANT, PLASTIC PACKAGE-2 |
| 文件： | 总9页 (文件大小：103K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Features
․High luminous intensity output
․Oval Shape
․Well defined spatial radiation
․Wide viewing angle (2θ1/2) : 110o / 40o
․UV resistant epoxy
․The product itself will remain within RoHS compliant version
Descriptions
․This precision optical performance oval LED is specifically
designed for passenger information signs
․This lamp has matched radiation patterns with red and blue
mixing color applications
Applications
․Color graphic signs
․Message boards
․Variable message signs (VMS)
․Commercial outdoor advertising
Device Selection Guide
LED Part No.
Chip Material Emitted Color
Lens Color
Stopper
No
5484BN/GADC-AMNA/MS
5484BN/GADC-AMNA/P/MS
InGaN
Brilliant Green Green Diffused
Yes
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 1 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Package Dimensions
Stopper Type
No Stopper Type
Notes:
․All dimensions are in millimeters, tolerance is 0.25mm except being specified.
․Protruded resin under flange is 1.5mm Max LED.
․Bare copper alloy is exposed at tie-bar portion after cutting.
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 2 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Absolute Maximum Rating (Ta=25℃)
Parameter
Symbol Absolute Maximum Rating
Unit
mA
mA
℃
Forward Current
IF
IFP
30
100
Pulse Forward Current (Duty1/10@ 1KHz)
Operating Temperature
Storage Temperature
Topr
Tstg
Tsol
Pd
-40 ~ +85
-40 ~ +100
260
℃
℃
Soldering Temperature
Power Dissipation
100
mW
V
Reverse Voltage
VR
5
Electrostatic Discharge
Notes: Soldering time≦5 seconds.
ESD
1K
V
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
IV
Min.
2880
--
Typ.
Max.
4970
--
Unit
mcd
deg
Condition
Luminous Intensity
Viewing Angle
--
2θ1/2
λp
X:110 Y:40
Peak Wavelength
Dominant Wavelength
Spectrum Half width
Forward Voltage
Reverse Current
--
522
530
35
--
--
IF=20mA
VR=5V
λd
nm
525
--
535
--
Δλ
VF
2.8
--
3.6
50
V
μA
IR
--
Rank Combination (IF=20mA)
Rank
M1
M2
N1
Luminous Intensity
2880~3450
3450~4140
4140~4970
*Measurement Uncertainty of Luminous Intensity: ±10%
Unit:mcd
Unit:nm
Rank
1
2
Dominant Wavelength
525~530
530~535
*Measurement Uncertainty of Dominant Wavelength ±1.0nm
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 3 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 4 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Packing Specification
■ Anti-electrostatic bag
Label
Pb
ELꢀECTROSTATICꢀELECTRONAGNETICꢀ
MAGNETICꢀORꢀRADIOACTIVEꢀRELDS
anti-staticꢀforꢀ750
■ Inner Carton
■ Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks of Luminous Intensity and Forward Voltage
HUE: Rank of Dominant Wavelength
REF: Reference
■ Outside Carton
LOT No: Lot Number
MADE IN TAIWAN: Production Place
■ Packing Quantity
1. 500 PCS/1 Bag，5 Bags/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 5 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Notes
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the
epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the
LED’s characteristics or it may break the LEDs.
Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures
may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead
position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration
of the epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from
Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or more,
they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture
absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity
environments where condensation can occur.
3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm from
solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended.
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 6 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Recommended soldering conditions:
Hand Soldering
DIP Soldering
300℃Max. (30W
Max.)
100℃ Max. (60 sec
Temp. at tip of iron
Preheat temp.
Max.)
Soldering time
Distance
3 sec Max.
Bath temp. & time
Distance
260 Max., 5 sec Max
3mm Min. (From
solder joint to epoxy
bulb)
3mm Min.(From
solder joint to
epoxy bulb)
Recommended soldering profile
laminar wave
Fluxing
Prehead
Avoiding applying any stress to the lead frame while the LEDs are at high temperature
particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or
vibration until the LEDs return to room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak
temperature.
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 7 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
Although the recommended soldering conditions are specified in the above table, dip or
handsoldering at the lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature
and dwell time in the solder wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for
a duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of
ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the
assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause
damage to the LED.
5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED
application. The current should be de-rated appropriately by referring to the de-rating curve
found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to
the data sheet de-rating curve.
6. ESD (Electrostatic Discharge)
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling
LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the
LEDs plastic lens as a result of friction between LEDs during storage and handing.
7. Other
Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 8 of 9
Prepared by: Grace Shen
Technical Data Sheet
5484BN/GADC-AMNA/X/MS
When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Everlight Electronics Co., Ltd.
Device Number : DLE-0001238
http\\:www.everlight.com
Prepared date: 04-15-2009
Rev 1
Page: 9 of 9
Prepared by: Grace Shen
相关型号：
5484BN/GADC-AMNA/P/MS
Single Color LED, Brilliant Green, Diffused Green, 5.2mm, ROHS COMPLIANT, PLASTIC PACKAGE-2
EVERLIGHT
5484GADCAMPAXMS
This precision optical performance oval LED is specifically designed for passenger information signs
EVERLIGHT
5484R3DCAHLCXMS
This precision optical performance oval LED is specifically designed for passenger information signs
EVERLIGHT
5484R5DCAJLBXMS
This precision optical performance oval LED is specifically designed for passenger information signs
EVERLIGHT
5484Y3DCAHLCXMS
This precision optical performance oval LED is specifically designed for passenger information signs
EVERLIGHT
5484Y5DCAJLBXMS
This precision optical performance oval LED is specifically designed for passenger information signs
EVERLIGHT
©2020 ICPDF网 联系我们和版权申明