HIR383C/L289 [EVERLIGHT]
Infrared LED,;
| 型号： | HIR383C/L289 |
| 厂家： | 
EVERLIGHT ELECTRONICS CO., LTD |
| 描述： | Infrared LED, 光电 |
| 文件： | 总9页 (文件大小：476K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
5mm Infrared LED
HIR383C/L289
Features
․High reliability
․High radi
․Peak wa
․2.54mm
․Low forw
․Pb Free
․This prod
Descriptio
․EVERLIGHT’s Infrared Emitting Diode (HIR383C/L289) is a
high intensity diode , molded in a water clear plastic package.
․The device is spectrally matched with phototransistor , photodiode
and infrared receiver module.
Applications
․Free air transmission system
․Infrared remote control units with high power requirement
․Smoke detector
․Infrared applied system
1
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11.22.2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Device Selection Guide
Chip
Lens Color
Water clear
Materials
GaAlAs
AAsolute Aaꢀiꢁuꢁ ꢂatinꢃs ꢄꢅaꢆꢇꢈ℃ꢉ
Parameter
Symbol
Rating
Unit
100
Continuous Forward Current
Peak Forward Current(*1)
Reverse Voltage
IF
mA
A
1.0
IFP
5
VR
V
Operating T
Storage Tem
Soldering T
Power Diss
25℃Free A
Notes: *1:IFP
*2:So
2
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Electro-Optical OOaracteristics ꢄꢅaꢆꢇꢈ℃ꢉ
Parameter
Symbol Min.
11
Typ.
35
Max. Unit
93
Condition
IF=5mA
IF=20mA
Ie
----- 140
----- 700
-----
-----
mW/sr
Radiant Intensity
IF=100
Pulse Width≦100μs and Duty≦1%
λp
nm
nm
IF=20mA
IF=20mA
Peak Wavelength
Spectral Bandwidth
----- 850
----- 45
-----
-----
Δλ
IF=20mA
----- 1.45
----- 1.80
1.65
2.40
V
IF=100mA
Forward Voltage
VF
nd Duty≦1%
Reverse Cu
View Angle
3
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
ꢅypical Electro-Optical OOaracteristics Ourves
Forward Current vs. Ambient Temperature
Spectral Distribution
140
100
80
I =20mA
F
120
100
80
Ta=25° C
60
60
40
20
40
20
0
0
790
870 890 910 930 950
810 830 850
-40 -20 0 20 40 60 80 100
Peak Emission
900
875
3
10
850
825
800
2
10
1
10
-25
0
50
75 100
25
0
1
2
3
4
5
6
7
8
4
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Radiant Intensity vs. Forward Current
Relative Radiant Intensity vs. Angular Displacement
-20
0
10
20
-10
1000
30
40
100
10
1.0
0.9
50
60
0.8
0.7
70
80
0
10 4
100
101
102 10 3
0.6 0.4 0.2 0 0.2 0.4 0.6
5
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Packaꢃe Diꢁension
Note: Tolera
6
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
■ Packinꢃ Quantity
1. 500 PCS/1 Bag, 5 Bags/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton
LaAel Forꢁ Specification
‧CPN: Customer’s Product Number
‧P/N: Product Number
Pb
‧QTQ: Packing Quantity
EVERLIGHT
X
‧CAT: Luminous Intensity Rank
‧HUE: Dom. Wavelength Rank
‧REF: Forward Voltage Rank
‧LOT No: Lot Number
RoHS
‧X: Month
HIR383C/L289
‧Reference: Identify Label Number
7
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Notes
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the LED’s characteristics or it
may break the LEDs.
Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs
are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight and the storage life limits
are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a
nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can
occur.
3. Soldering
Carefnt to epoxy bulb,
and s
Reco
x.)
Tem
Sold
Dist
lder
Reco
Fluxing
Prehead
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to
room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
8
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
DATASHEET
5.0mm Infrared LED
HIR383C/L289
Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest
possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6. ESD (Electro
Elect
An E
All de
Use is as a result of
frictio
7. Other
Abovange for above
speci
When utlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t
reproduce or cause anyone to reproduce them without EVERLIGHT’s consent.
9
Copyright © 2010, Everlight All Rights Reserved. Release Date : 11 .22, 2012. Issue No: DIR-0000363
www.everlight.com
Ver.:1 Release Date:12/10/2012 Confidential Level:一般 狀態:Approved(正式發行)
ꢀ
相关型号：
HIR67-21C/B/TR8
Infrared LED, 2.4mm, 1-Element, 850nm, ROHS COMPLIANT, MINIATURE, PLASTIC, SMD, 2 PIN
EVERLIGHT
©2020 ICPDF网 联系我们和版权申明