PD15-22C-L3 [EVERLIGHT]
Silicon PIN Photodiode; 硅PIN光电二极管
| 型号： | PD15-22C-L3 |
| 厂家： | 
EVERLIGHT ELECTRONICS CO., LTD |
| 描述： | Silicon PIN Photodiode |
| 文件： | 总9页 (文件大小：153K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Technical Data Sheet
Silicon PIN Photodiode
PD15-22C/L3/TR8
Features
․Fast response time
․High photo sensitivity
․Small junction capacitance
․Pb free
․The product itself will remain within RoHS compliant version.
Descriptions
․PD15-22C/L3/TR8 is a high speed and high sensitive
PIN photodiode in miniature flat top view lens
SMD package and it is molded in a water clear
plastic. The device is spectrally matched to visible
and infrared emitting diode.
Applications
․High speed photo detector
․Copier
․Game machine
Device Selection Guide
Chip
LED Part No.
Lens Color
Material
PD
Silicon
Water clear
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 1 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Package Dimensions
2.1
2.0
3.3
2.3
2.1
1.2
4-R0.25
Notes: 1.All dimensions are in millimeters
2.Tolerances unless dimensions ±0.1mm
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
32
Units
mA
Reverse Voltage
VR
℃
℃
Operating Temperature
Storage Temperature
Topr
Tstg
-25 ~ +85
-40 ~ +85
260
℃
Soldering Temperature*1
Tsol
mW
Power Dissipation at(or below)
Pc
150
25℃Free Air Temperature
Notes: *1:Soldering time≦5 seconds.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 2 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Condition
Min Typ Max Unit
λ0.5
Rang Of Spectral Bandwidth
---
400
---
---
1100 nm
λP
Wavelength Of Peak Sensitivity
Open-Circuit Voltage
---
940
---
---
nm
V
Ee=5mW /cm2
λP=940nm
VOC
---
---
0.44
2.4
Ee=1mW /cm2
μA
μA
Short-Circuit Current
ISC
---
λP=875nm
Ee=1mW /cm2
λP=875nm
VR=5V
Reverse Light Current
Reverse Dark Current
IL
ID
---
---
32
2.4
---
---
10
---
Ee=0mW /cm2
nA
V
VR=10V
Ee=0mW /cm2
IR=100μA
Reverse Breakdown Voltage
BVR
170
Ee=0mW /cm2
f=1MHz
Total Capacitance
Ct
---
10
---
pF
nS
VR=5V
Rise Time
Fall Time
tr
tf
---
---
10
10
---
---
VR=5V
RL=100Ω
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date：07-20-2005
Rev 2
Page: 3 of 9
Device No：DTD-152-159
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Typical Electro-Optical Characteristics Curves
Fig.1 Power Dissipation vs.
Ambient Temperature
200
Fig.2 Spectral Sensitivity
1.0
C
Ta=25
0.8
0.6
150
100
0.4
50
0
0.2
0
-25
25
50
75 85 100
0
100 300 500 700 900 1100 1300
Fig.3 Dark Current vs.
Ambient Temperature
Fig.4 Reverse Light Current vs.
Ee
1000
8
6
100
4
10
1
2
VR=5V
VR=10V
0
0.5
1.5
3.0
20
60
80
100
1.0
40
2
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 4 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Typical Electro-Optical Characteristics Curves
Fig.5 Terminal Capacitance vs.
Reverse Voltage
Fig.6 Response Time vs.
Load Resistance
101
100
40
30
VR=10V
Ta=25OC
f=1MHZ
VR=5V
2
-1
10
20
10
0
-2
10
-3
10
101
102
103
104
105
0.1
1
10
100
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date：07-20-2005
Rev 2
Page: 5 of 9
Device No：DTD-152-159
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 6 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 7 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Reliability Test Item And Condition
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
NO. Item
Test Conditions
Test Hours/ Sample Failure
Ac/Re
Cycles
Sizes
22pcs
22pcs
Judgement
Criteria
TEMP.：260℃±5℃
1 REFLOW Soldering
2 Temperature Cycle
6Mins
0/1
0/1
IL≦L×0.8
5secs
H : +100℃
15mins
50Cycles
L：Lower
Specification
Limit
5mins
L : -40℃
15mins
H :+100℃
5mins
3 Thermal Shock
50Cycles
22pcs
0/1
10secs
5mins
L :-10℃
TEMP.：+100℃
4 High Temperature
Storage
1000hrs
1000hrs
22pcs
22pcs
0/1
0/1
TEMP.：-40℃
5 Low Temperature
Storage
6 DC Operating Life VR=5V
1000hrs
1000hrs
22pcs
22pcs
0/1
0/1
85℃ / 85% R.H
7 High Temperature/
High Humidity
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Rev 2
Page: 8 of 9
Device No：DTD-152-159
Prepared date：07-20-2005
Prepared by：Jaine Tsai
PD15-22C/L3/TR8
Packing Quantity Specification
1.1000PCS/1Bag，20Bags/1Box
2.10Boxes/1Carton
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Ranks
RoHS
PD15-22C/L3/TR8
HUE: Peak Wavelength
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s
consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Prepared date：07-20-2005
Rev 2
Page: 9 of 9
Device No：DTD-152-159
Prepared by：Jaine Tsai
相关型号：
©2020 ICPDF网 联系我们和版权申明