SPX29500T-1.8/TR [EXAR]

Regulator, 1 Output, BIPolar,;
SPX29500T-1.8/TR
型号: SPX29500T-1.8/TR
厂家: EXAR CORPORATION    EXAR CORPORATION
描述:

Regulator, 1 Output, BIPolar,

文件: 总11页 (文件大小:557K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
®
SPX29500/01/02/03  
5A Low Dropout Voltage Regulator  
Adjustable & Fixed Output, Fast Response Time  
FEATURES  
Adjustable Output Down to 1.25V  
1% Output Accuracy  
Output Current of 5A  
Low Dropout Voltage: 370mV @ 5A  
Tight Line Regulation: 0.06%  
Load Regulation: 0.2%  
SPX29502  
5 Pin TO-263  
SP29500  
Fast Transient Response  
Reverse-Battery Protection  
Current Limit and Thermal Protection  
3 Pin TO-220  
1
2
3
1
2
3
APPLICATIONS  
Powering VGA & Sound Card  
Power PC™ Supplies  
SMPS Post Regulator  
High Efficiency “Green” Computer  
Systems  
VIN  
VOUT  
GND  
High Efficiency Linear Power Supplies  
Constant Current Regulators  
Adjustable Power Supplies  
Battery Charger  
Now Available in Lead Free Packaging  
DESCRIPTION  
TheSPX29500/01/02/03are5Ahighlyaccuratevoltageregulatorswithalowdropoutvoltageof370mV  
@ 5A. These regulators are specifically designed for low voltage applications that require a low dropout  
voltage and a fast transient response. They are fully fault protected against over-current, reverse  
battery, and positive and negative voltage transients. On-Chip trimming adjusts the reference voltage  
to 1% initial accuracy. Other features in the 5 pin versions include Enable, and Error Flag.  
The SPX29500/01/02/03 are offered in 3 & 5-pin TO-220 & TO-263 packages. For a 1.5A version, refer  
to the SPX29150 data sheet. For a 3A version, refer to the SPX29300 datasheet.  
TYPICAL APPLICATION CIRCUITS  
SPX29502  
1
2
4
V
V
1
SPX29500  
3
VOUT  
OUT  
V
IN  
6.8µF  
IN  
+
+
5
3
22µF  
2
+
+
R1  
22µF  
ADJ  
6.8µF  
GND  
R2  
Figure 1. Fixed Output Linear Regulator  
Figure 2. Adjustable Output Linear Regulator  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
1
ABSOLUTE MAXIMUM RATINGS  
Lead Temperature (soldering, 5 seconds) ................260°C  
Storage Temperature Range........................-65°C to +150°C  
Operating Junction Temperature Range......-40°C to +125°C  
Input Voltage (Note 1) .................................................... 20V  
OPERATING RATINGS  
Input Voltage ................................................................... 16V  
ELECTRICAL CHARACTERISTICS  
Specifications are at VIN = VOUT + 1V and IOUT = 10mA, CIN = 6.8µF, COUT = 22µF, TA = 25°C, unless otherwise specified.  
The denotes the specifications which apply over the full operating temperature range, unless otherwise specified.  
PARAMETER  
MIN  
TYP  
MAX  
UNITS  
CONDITIONS  
Fixed Voltage Options  
1.8V Version  
SPX29500/01  
Output Voltage  
1.782  
1.764  
1.800  
1.800  
1.818  
1.836  
V
V
V
V
IOUT = 10mA  
10mA IOUT 5A, 2.8V VIN 16V  
2.5V Version  
Output Voltage  
2.475  
2.450  
2.500  
2.500  
2.525  
2.550  
IOUT = 10mA  
10mA IOUT 5A, 3.5V VIN 16V  
3.3V Version  
Output Voltage  
3.267  
3.234  
3.300  
3.300  
3.333  
3.366  
IOUT = 10mA  
10mA IOUT 5A, 4.3V VIN 16V  
5.0V Version  
Output Voltage  
4.950  
4.900  
5.000  
5.000  
5.050  
5.100  
IOUT = 10mA  
10mA IOUT 5A, 6.0V VIN 16V  
All Voltage Options  
Line Regulation  
Load Regulation  
V/T  
SPX29500/01/02/03  
0.06  
0.2  
20  
0.5  
%
%
IOUT=10mA,(VOUT+1V) VIN 16V  
VIN=VOUT+2V, 10mAIOUT IFL (Note 2)  
VOUT Temp Coefficient (Note 5)  
1
100  
250  
ppm/°C  
mV  
Dropout Voltage, except  
1.8V  
80  
IOUT=250mA  
IOUT=2.5A  
IOUT=5A  
200  
370  
600  
50  
Ground Current  
(Note 4)  
20  
70  
mA  
mA  
IOUT=2.5A  
IOUT=5A  
Ground Pin Current  
at Dropout  
3
VIN=0.5V less than specified VOUT,  
IOUT=10mA  
Current Limit  
7.5  
10  
A
(Note 3)  
Output Noise Voltage  
(10Hz to 100kHz)  
IL=100mA  
425  
µVRMS  
CL=22µF  
350  
CL=33µF  
Reference Voltage  
1.228  
1.215  
1.240  
1.252  
1.265  
V
Adjustable version only  
Reference Voltage  
1.203  
1.277  
V
Adjustable version only (Note 7)  
(Note 6)  
Adjust Pin Bias Current  
40  
20  
80  
120  
nA  
Reference Voltage  
Temp. Coeff.  
ppm/°C  
nA/°C  
Adjust Pin Bias  
0.1  
Current Temp. Coeff.  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
2
ELECTRICAL CHARACTERISTICS: Continued  
Specifications are at VIN = VOUT + 1V and IOUT = 10mA, CIN = 6.8µF, COUT = 22µF, TA = 25°C, unless otherwise specified.  
The denotes the specifications which apply over the full operating temperature range, unless otherwise specified.  
PARAMETER  
MIN  
TYP  
SPX29501/03  
0.01  
MAX  
UNITS  
CONDITIONS  
Flag Output (Error Comparator)  
Output Leakage  
Current  
1
2
µA  
mV  
mV  
mV  
mV  
VOH=16V  
Output Low Voltage  
220  
60  
300  
400  
Device set for 5V,VIN=4.5V, IOL=250µA  
Device set for 5V, (Note 8)  
Device set for 5V, (Note 8)  
Device set for 5V, (Note 8)  
Upper Threshold  
Voltage  
40  
25  
Lower Threshold  
Voltage  
75  
95  
140  
Hysteresis  
15  
Enable Input  
SPX29501/02  
Input Logic Voltage  
Low (OFF)  
0.8  
V
(Note 10)  
High (ON)  
2.4  
ENABLE Input Current  
100  
0.6  
600  
750  
2
µA  
µA  
VEN=16V  
VEN=0.8V  
4
Regulator Output  
10  
µA  
(Note 9)  
Current in Shutdown  
500  
Thermal Resistance  
2
60  
2
°C/W  
TO-220 Junction to Case, at Tab  
TO-220 Junction to Ambient  
TO-263 Junction to Case, at Tab  
TO-263 Junction to Ambient  
60  
NOTES:  
Note 1: Maximum positive supply voltage of 20V must be of limited duration (<100ms) and duty cycle of less than 1%. The  
maximum continuous supply voltage is 16V.  
Note 2: Full load current (IFL) is defined as 5A.  
Note 3: VIN = VOUT (NOMINAL) +1V. For example, use VIN = 4.3V for a 3.3V regulator. Employ pulse-testing procedures to minimize  
temperature rise.  
Note 4 Ground pin current is the regulator quiescent current. The total current drawn from the source is the sum of the load current  
plus the ground pin current.  
Note 5: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.  
Note 6: Thermal regulation is defined as the change in output voltage at time T after a change in power dissipation is applied,  
excluding load / line regulation effects. Specifications for a 200mA load pulse as VIN = 20V (a 4W pulse) for t = 10ms.  
Note 7: VREFVOUT (VIN-1), 2.3VVIN 16V, 10mA IL IFL, Tj < Tjmax  
.
Note 8: Comparator threshold is expressed in terms of a voltage differential at the Adjust terminal below the nominal reference  
voltage measured 6V input. To express these thresholds in terms of output voltage change, multiply the error amplifier gain =  
V
OUT/VREF = (R1 + R2)/R2. For example, at a programmable output voltage of 5V, the Error output is guaranteed to go low when  
the output drops by 95mVx 5V/ 1.240V = 383mV. Threshold remain constant as a percent of VOUT as VOUT is varied, with the  
dropout warning occurring at typically 5% below nominal, 7.7% guaranteed.  
Note 9: VEN 0.4V and VIN 16V, VOUT = 0.  
Note 10: Measured with IOUT = IOUT MIN (10mA).  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
3
FUNCTIONAL DIAGRAM  
IN  
OUT  
O.V  
ILIMIT  
1.180V  
FLAG  
1.240V  
20V  
R1*  
Reference  
+
-
+
-
ADJ  
EN  
Thermal  
Shutdown  
R2*  
GND  
TYPICAL PERFORMANCE CHARACTERISTICS  
600  
550  
500  
450  
400  
350  
300  
250  
200  
150  
100  
50  
120  
110  
100  
90  
80  
70  
60  
50  
40  
30  
20  
10  
0
0
1
2
3
4
5
0
1
2
3
4
5
6
Output Current (A)  
Output Current (A)  
Figure 3. Ground Current (mA) vs. Output Current (A)  
Figure 4. Dropout (mV) vs. Output Current (A)  
VOUT (AC)  
VOUT (AC)  
IOUT (2A/DIV)  
VIN  
Figure 5. Load Transient (VIN=4V, VO=3.3V, COUT=22µF,  
Figure 6. Line Transient (COUT=22µF, IO=10mA)  
10mA~5A)  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
4
APPLICATION INFORMATION  
load transient response is needed. If the power  
source has a high AC impedance, a 0.1µF ce-  
ramic capacitor between input & ground is rec-  
ommended.  
The SPX29500/01/02/03 incorporates protec-  
tion against over-current faults, reversed load  
insertion, over temperature operation, and posi-  
tive and negative transient voltage.  
Thermal Considerations  
Minimum Load Current  
Although the SPX29500/01/02/03 offers limit-  
ing circuitry for overload conditions, it is still  
necessary to insure that the maximum junction  
temperature is not exceeded in the application.  
Heat will flow through the lowest resistance  
path,thejunction-to-casepath. Inordertoinsure  
the best thermal flow of the component, proper  
mounting is required.  
To ensure a proper behavior of the regulator  
under light load, a minimum load of 10mA for  
SPX29500/01/02/03 is required.  
Adjustable Regulator Design  
The SPX29502/03 are adjustable regulators that  
can be programmed to any value between 1.24V  
and 16V using 2 resistors, R1 and R2. The  
relationship between the resistors is:  
TO-220 Design Example:  
Assume that VIN = 8V, VOUT = 5V, IOUT = 5A, TA  
= 50°C, θHA= 1°C/W, θCH= 2°C/W, and θJC=  
2°C/W, where:  
R1 = R2(VOUT/1.24-1).  
Error Flag  
The SPX29501/03 features an error flag that  
indicates either an over current or under voltage  
condition. The flag output goes low, sinking  
10mA when either condition occurs.  
TA = ambient temperature,  
θHA= heatsink to ambient thermal  
resistance  
θCH= case to heatsink thermal  
resistance  
Enable Input  
θJC = junction to case thermal  
resistance  
The SPX29501/02 have an Enable function that  
switches the regulator on and off. Their thresh-  
oldsareTTLcompatible. Enablingtheregulator  
requires approximately 20µA of current.  
The power calculated under these conditions is:  
PD = (VIN – VOUT) * IOUT = 15W.  
Typical Application Circuits  
And the junction temperature is calculated as  
TJ = TA + PD * (θHA + θCH + θJC) or  
TJ = 50 + 15 * (1+2+2) = 125°C  
Figure 1 represents at typical fixed output regu-  
lator. Figure 2 represents an adjustable output  
regulator. ThevaluesofR1andR2settheoutput  
voltage value as follows:  
Reliable operation is insured.  
VOUT =VREF * [1 + (R1/R2)].  
Capacitor Requirements  
The output capacitor is needed to insure stability  
and minimize the output noise. The value of the  
capacitor varies with the load. However, a  
minimum value of 22µF aluminum capacitor  
will guarantee stability over all load conditions.  
A tantalum capacitor is recommended if a faster  
For best results, the total series resistance should  
guarantee a minimum regulator load current of  
10mA.  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
5
PACKAGES  
TO-263-3 Package (T)  
TO-263-5 Package (T5)  
SPX29500  
1)VIN  
SPX29501  
1)ENABLE  
2)INPUT  
SPX29502  
1) ENABLE  
2) INPUT  
SPX29503  
1)FLAG  
1
2
3 4 5  
1
2
3
2)GND  
2)INPUT  
3)  
VOUT  
3)GND  
3)  
4) OUTPUT  
5)  
GND  
3)  
GND  
4)OUTPUT  
5)  
4)OUTPUT  
5)  
ADJUST  
ADJUST  
FLAG  
V
V
GND  
Top View  
IN  
OUT  
Front View  
TO-220-3 Package (U)  
TO-220-5 Package (U5)  
SPX29503  
SPX29501  
1)ENABLE  
2)INPUT  
SPX29502  
SPX29500  
1)VIN  
2)GND  
3)VOUT  
1
2
3
1)  
2)  
3)  
4)  
5)  
1)  
2)  
3)  
4)  
5)  
ENABLE  
INPUT  
GND  
OUTPUT  
FLAG  
INPUT  
GND  
OUTPUT  
ADJUST  
3)  
4)  
5)  
GND  
OUTPUT  
FLAG  
ADJUST  
GND  
IN  
Front View  
1 2 3 4 5  
Top View  
V
V
OUT  
*Tab is internally connected to GND  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
6
PACKAGES: 3 PIN TO-263  
E
A
K
B
S
H
M
L
W
P
-A-  
N
G
D
R
TERMINAL 8  
C
U
V
DIMENSIONS  
in inches  
SYMBOL  
MIN  
.396  
MAX  
0.406  
0.336  
0.180  
0.036  
0.055  
0.100 REF  
0.620  
0.066  
.010  
A
B
C
D
E
G
H
K
L
0.326  
0.170  
0.026  
0.045  
0.100 REF  
0.580  
0.055  
.000  
M
N
P
R
S
U
V
W
0.098  
.017  
0.108  
.023  
.090  
.110  
0°  
8°  
.095  
.105  
.30 REF  
.305 REF  
.010  
.30 REF  
.305 REF  
.010  
3 Pin TO-263  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
7
PACKAGES: 5 PIN TO-263  
20° 2°  
A
E
C2  
L1  
D
A1  
H
L
b
e
C
R
DIMENSIONS  
in inches  
SYMBOL  
MIN  
.380  
MAX  
0.420  
0.380  
0.190  
0.039  
0.065  
E
D
0.330  
0.160  
0.020  
0.045  
0.067 REF  
0.575  
0.055  
.015  
A
b
C2  
e
0.067 REF  
0.625  
0.066  
.029  
H
L1  
C
L
0.090  
.000  
0.110  
.010  
A1  
R
0°  
8°  
5 Pin TO-263  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
8
PACKAGES: 3 PIN TO-220  
φ P  
E
α (5X)  
Q
D
H1  
V
E-PIN  
R
b1  
L
e3  
C1  
J1  
DIMENSIONS  
e
in inches  
e1  
SYMBOL  
MIN  
0.160  
MAX  
0.190  
A
b
0.025  
0.040  
C1  
D
0.015  
0.022  
0.560  
0.590  
E
0.385  
0.415  
e
0.090  
0.110  
C
L
e1  
e3  
F
0.190  
0.210  
0.045  
0.055  
0.045  
0.055  
H1  
J1  
φ P  
Q
0.234  
0.258  
F
0.090  
0.115  
A
0.146  
0.156  
0.103  
0.113  
L
0.540  
0.560  
α
3° typ  
7° typ  
b1  
0.450  
0.060  
R
U
V
0.243 REF  
0.300 REF  
0.240 REF  
6.170 REF  
7.620 REF  
6.100 REF  
3 Pin TO-220  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
9
PACKAGES: 5 PIN TO-220  
φ P  
A
Q
E
A1  
H1  
D
SEATING  
PLANE  
α
L
e
b
C
e1  
A2  
DIMENSIONS  
in inches  
SYMBOL  
MIN  
0.165  
MAX  
0.19  
A
A1  
A2  
C
0.045  
0.055  
0.09  
0.115  
0.012  
0.025  
D
0.560  
0.596  
e
0.067 BSC  
0.268 REF  
0.385  
0.067 BSC  
0.268 REF  
0.415  
e1  
E
H1  
b
0.224  
0.258  
0.025  
0.04  
φ P  
Q
0.146  
0.156  
0.103  
0.113  
L
0.54  
0.56  
α
7° typ  
7° typ  
5 Pin TO-220  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
10  
ORDERING INFORMATION  
PART NUMBER  
ACCURACY  
OUTPUT VOLTAGE  
PACKAGE  
SPX29500U-1.8 ................... 1.0% ................................... 1.8V .............................. 3 lead TO-220  
SPX29500U-2.5 ................... 1.0% ................................... 2.5V .............................. 3 lead TO-220  
SPX29500U-3.3 ................... 1.0% ................................... 3.3V .............................. 3 lead TO-220  
SPX29500U-5.0 ................... 1.0% ................................... 5.0V .............................. 3 lead TO-220  
SPX29500T-1.8 ................... 1.0% ................................... 1.8V .............................. 3 lead TO-263  
SPX29500T-2.5 ................... 1.0% ................................... 2.5V .............................. 3 lead TO-263  
SPX29500T-3.3 ................... 1.0% ................................... 3.3V .............................. 3 lead TO-263  
SPX29500T-5.0 ................... 1.0% ................................... 5.0V .............................. 3 lead TO-263  
SPX29501U5-1.8 ................. 1.0% ................................... 1.8V .............................. 5 lead TO-220  
SPX29501U5-2.5 ................. 1.0% ................................... 2.5V .............................. 5 lead TO-220  
SPX29501U5-3.3 ................. 1.0% ................................... 3.3V .............................. 5 lead TO-220  
SPX29501U5-5.0 ................. 1.0% ................................... 5.0V .............................. 5 lead TO-220  
SPX29501T5-1.8 ................. 1.0% ................................... 1.8V .............................. 5 lead TO-263  
SPX29501T5-2.5 ................. 1.0% ................................... 2.5V .............................. 5 lead TO-263  
SPX29501T5-3.3 ................. 1.0% ................................... 3.3V .............................. 5 lead TO-263  
SPX29501T5-5.0 ................. 1.0% ................................... 5.0V .............................. 5 lead TO-263  
SPX29502T5........................ 1.0% .................................... Adj................................ 5 lead TO-263  
SPX29502U5 ....................... 1.0% .................................... Adj................................ 5 lead TO-220  
SPX29503T5........................ 1.0% .................................... Adj................................ 5 lead TO-263  
SPX29503U5 ....................... 1.0% .................................... Adj................................ 5 lead TO-220  
Please consult the factory for pricing and availability on a Tape-On-Reel option.  
Available in lead free packaging. To order, add "-L" suffix to the part number.  
Example: SPX29500U-1.8 = standard; SPX29500U-L -1.8 = lead free.  
Corporation  
ANALOGEXCELLENCE  
Sipex Corporation  
Headquarters and  
Sales Office  
233 South Hillview Drive  
Milpitas, CA 95035  
TEL: (408) 934-7500  
FAX: (408) 935-7600  
Sales Office  
22 Linnell Circle  
Billerica, MA 01821  
TEL: (978) 667-8700  
FAX: (978) 670-9001  
e-mail: sales@sipex.com  
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the  
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.  
Rev:A Date: 3/8/04  
SPX29500/01/02/03 5A Low Dropout Voltage Regulator  
© Copyright 2004 Sipex Corporation  
11  

相关型号:

SPX29500T-2-5/TR

Fixed Positive LDO Regulator, 2.5V, 0.6V Dropout, PSSO3, TO-263, 3 PIN

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-2.5

5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response Time

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-2.5/TR

Regulator, 1 Output, BIPolar,

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
EXAR

SPX29500T-3.3

5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response Time

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-3.3/TR

Regulator, 1 Output, BIPolar,

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
EXAR

SPX29500T-5-0/TR

Fixed Positive LDO Regulator, 5V, 0.6V Dropout, PSSO3, TO-263, 3 PIN

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-5.0

5A Low Dropout Voltage Regulator Adjustable & Fixed Output, Fast Response Time

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-5.0/TR

Regulator, 1 Output, BIPolar,

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
EXAR

SPX29500T-L-1-8

5A Low Dropout Voltage Regulator

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
EXAR

SPX29500T-L-1-8/TR

Fixed Positive LDO Regulator, 1.8V, 0.6V Dropout, PSSO3, TO-263, 3 PIN

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-L-1.8

Fixed Positive LDO Regulator, 1.8V, 0.6V Dropout, PSSO3, TO-263, 3 PIN

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
SIPEX

SPX29500T-L-1.8/TR

Regulator, 1 Output, BIPolar,

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
EXAR