XR-T3588 [EXAR]
V.35 Interface Receiver/Transmitter; V.35接口接收器/发送器
| 型号： | XR-T3588 |
| 厂家： | 
EXAR CORPORATION |
| 描述： | V.35 Interface Receiver/Transmitter |
| 文件： | 总12页 (文件大小：164K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
...the analog plus companyTM
XR-T3588-89ES
November 1996-3
XR-T3588/89
Evaluation System
User Manual
Rev. 1.00
E1996
EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 z (510) 668-7000 z FAX (510) 668-7017
XR-T3588-89ES
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to im-
prove design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits de-
scribed herein, conveys no license under any patent or other right, and makes no representation that the circuits are
free of patent infringement. Charts and schedules contained herein are only for illustration purposes and may vary
depending upon a user’s specific application. While the information in this publication has been carefully checked;
no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly
affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the
user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circum-
stances.
Copyright 1996 EXAR Corporation
User Manual November 1996
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
Rev. 1.00
2
Table of Contents
OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
XR-T3588 DIGITAL INPUT AND XR-T3589
DIGITAL OUTPUT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
XR-T3588 LINE OUTPUT AND XR-T3589 LINE INPUT
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSMITTER AND RECEIVER POWER-DOWN . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1. XR-T3588 Transmitter Selection . . . . . . . . . . . . . . . . . . . . . . . .
Table 2. XR-T3589 Receiver Selection . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
6
XR-T3589 GROUND POTENTIAL OFFSET TESTING . . . . . . . . . . . . . . . . . . . . . . .
6
ADDENDUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 3. List of Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 2. Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 3. Circuit Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
7
8
Rev. 1.00
3
XR-T3588-89ES
This Page Intentionally Left Blank
Rev. 1.00
4
XR-T3588-89ES
XR-T3588/89
...the analog plus companyTM
Evaluation System
OVERVIEW
Likewise, the TTL compatible receiver outputs are the
BNC connectors labeled RX1OUT, RX2OUT and
RX3OUT.
Thisunitisa4.5by5.0inchcircuitboardthatsimplifiesthe
evaluation of the XR-T3588 line driver and the XR-T3589
line receiver devices in a CCITT V.35 application. Its
features include dip switch selection of channel
power-down options, and provisions for applying the
ground potential offset voltage specified by the V.35 test
procedure to the receiver inputs. Figure 1., Figure 2. and
Table 3. show the demo board component layout, circuit
diagram and list of components respectively.
XR-T3588 LINE OUTPUT AND XR-T3589 LINE INPUT
CONNECTIONS
The line connections are made to the six RJ-11
connectors or to the corresponding test point pairs that
are located on the right side of the board. The RJ-11s are
for connecting twisted pair cables, and the test points
provide a convenient means for viewing the output and
input signals differentially on an oscilloscope. From top to
bottom, the three transmitter outputs are labeled
TX1OUT, TX2OUT, and TX3OUT, and the three receiver
inputs are labeled RX1IN, RX2IN, and RX3IN. Note that
connectors are wired so that the “A” and “B” XR-T3588
output pins and the “A” and “B” XR-T3589 input pins go to
the same pin numbers on the RJ-11 connectors.
Therefore, a test cable must be wired in the same manner
to prevent a data inversion between the transmitter digital
input and the receiver digital output. (Telephone cables
typically contain a “twist” between modular connectors,
and will therefore give a data inversion.)
POWER REQUIREMENTS
Supply voltages of +5.0V ꢀ5% for V and -5.0V ꢀ5%
CC
for V are applied to the board through banana jacks.
EE
Both power sources should be well-regulated, and each
must be capable of supplying 250mA minimum. During
normal operation jumper E-1 must be installed, and
nothing is connected to the banana jack labeled OFFSET.
XR-T3588 DIGITAL INPUT AND XR-T3589 DIGITAL
OUTPUT CONNECTIONS
TRANSMITTER AND RECEIVER POWER-DOWN
The TTL compatible transmitter inputs are the BNC
connectors mounted on the left side of the board that are
labeled TX1IN, TX2IN and TX3IN. Provisions are
included for installing input termination resistors R1, R2,
and R3 if required. These resistors (50 or 75Ω) are
needed only if a pulse generator with a low impedance
output and a fast rise time is used as a test signal source.
They are not required for TTL signals applied to the board
through short cables.
The four-position DIP switch located in the center of the
board selects the logic state applied to the transmitter and
receiver channel enable pins. The top two sections
labeled TX, and the bottom two sections labeled RX are
for the XR-T3588 and XR-T3589 respectively. Table 1.
and Table 2. show the powering options. Note that when
a DIP switch section is “OFF,” a logic 1 is applied to the
corresponding IC pin.
XR-T3588
Transmitter
1, 2, 3, On
1, 2, On
TX Switch Sections
SEL A
SEL B
Off
Off
Off
On
On
On
1 On
Off
All Off
On
Table 1. XR-T3588 Transmitter Selection
Rev. 1.00
5
XR-T3588-89ES
XR-T3589
RX Switch Sections
SEL A SEL B
Off Off
Receiver
1, 2, 3, On
1, 2, On
1 On
Off
On
On
On
Off
On
All Off
Table 2. XR-T3589 Receiver Selection
XR-T3589 GROUND POTENTIAL OFFSET TESTING
this test, jumper E-1 is first removed and then a DC
voltage in the range of ꢀ4V is applied between the GND
and OFFSET banana jacks.
The receiver ground potential offset test specified by
CCITT V.35 may be performed on the demo board. For
ADDENDUM
Qty.
Value
Ref. Designators
Notes
15
51.1Ω, 1/4W, 1% Metal Film Resistor
R1,2,3,5,7,8,10,11,
13,14,16,17,19,20,22
1
10K, 2%, 5 Resistor, Thick-Film Network,
Panasonic
R4
6
1
2
121Ω, 1/4W, 1% Metal Film Resistor
R6,9,12,15,18,21
3.92K, 1/4W, 1% Metal Film Resistor
R23
22µF, 16V, Electrolytic, Axial Lead,
5mm Dia., 2mm Spacing, Panasonic Type
NHE
C1,2
5
0.1µF, 63V, Z5U Dilectric,
Axial Lead, 0.1” Spacing, Panasonic
C3,4,5,6,7
1
2
1
6
6
3
4-Position DIP Switch, CTS
2 Pin Single-Row Header, Gold
Shorting Jumper for Above Header
Female BNC Connector, PC Mount
6-Pin RJ-11 Connector
S1
E1
Connector for Digital I/O
Connector for Line
Banana Jack (1 Black, 1 Red, 1 Blue, 1
Green)
GND, VCC, VSS, OFFSET
Connectors
13
1
Pins for Digital I/O and Ground Pads
14 pin DIP Socket
1
18 pin DIP Socket
4
Spacers to Elevate Board
4-40 x 5/16” Screws
4
To Attach Spacers
Table 3. List of Components
Rev. 1.00
6
XR-T3588-89ES
Figure 1. Component Layout
Rev. 1.00
7
XR-T3588-89ES
Rev. 1.00
8
XR-T3588-89ES
Notes
Rev. 1.00
9
...the analog plus companyTM
EXAR Corporation
48720 Kato Road
Fremont, CA 94538
(510) 668-7000, Fax (510) 668-7017
Worldwide Web Site: http://www.exar.com
Rev. 1.00
E1996
XR-T3588-89ES
Notes
Rev. 1.00
10
XR-T3588-89ES
Notes
Rev. 1.00
11
相关型号：
©2020 ICPDF网 联系我们和版权申明