XRT82D20_06 [EXAR]
SINGLE CHANNEL E1 LINE INTERFACE UNIT; 单路E1线路接口单元
| 型号： | XRT82D20_06 |
| 厂家： | 
EXAR CORPORATION |
| 描述： | SINGLE CHANNEL E1 LINE INTERFACE UNIT |
| 文件： | 总27页 (文件大小：439K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
AUGUST 2006
REV.1.0.8
GENERAL DESCRIPTION
• Clock Recovery and Selectable Crystal-less Jitter
attenuator
The XRT82D20 is a fully integrated, single channel,
Line Interface Unit (Transceiver) for 75 Ω or 120 Ω E1
(2.048 Mbps) applications. The LIU consists of a
receiver with adaptive data slicer for accurate data
and clock recovery and a transmitter which accepts
either single or dual-rail digital inputs for signal
transmission to the line using a low- impedance
differential line driver. The LIU also includes a crystal-
less jitter attenuator for clock and data smoothing
which, depending on system requirements, can be
selected in either the transmit or receive path.
• Compliant with ETS300166 Return Loss
• Compliant with the ITU-T G.823 Jitter Tolerance
Requirements
• Remote, Local and Digital Loop backs
• Declares and Clears LOS per ITU-T G.775
• Logic Inputs accept either 3.3V or 5.0V levels
0
0
• - 40 C to 85 C Temperature Range
• Low Power Dissipation; 145mW with 120 Ω or
160mW with 75 Ω typical
Coupling the XRT82D20 to the line requires
transformers on both the Receiver and Transmitter
sides, and supports both 120 Ω balanced and 75 Ω
• +3.3V or +5V Supply Operation
• Pin Compatible with the XRT7288
APPLICATIONS
unbalanced interfaces.
The receiver can be
capacitive coupled to for cost reduction
FEATURES
• PDH Multiplexers
• Complete E1 (CEPT) line interface unit
• SDH Multiplexers
• Generates transmit output pulses that are
compliant with the ITU-T G.703 Pulse Template for
2.048Mbps (E1) rates
• Digital Cross-Connect Systems
• DECT (Digital European Cordless Telephone) Base
Stations
• On-Chip Pulse Shaping for both 75 Ω and 120 Ω
Line Drivers
• CSU/DSU Equipment
• Test Equipment
FIGURE 1. BLOCK DIAGRAM OF THE XRT82D20
TTIP
TClk
TPOS
TNEG
HDB3
Encoder
Tx Pulse
Shaper
Line
Driver
MUX
TRing
Jitter Attenuator
Local
Loopback
Digital
Remote
Loopback
Loopback
LOS
RLOS
Detect
Data &
Timing
Recovery
RClk
RPOS
RNEG
HDB3
Decoder
Data
Peak
RTIP
MUX
Slicer
Detector
RRing
Timing
Generator
MClk
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
FIGURE 2. PINOUT OF THE XRT82D20
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
RTIP
RLOS
2
RRing
MuteRx
AGND
AVDD
TxLEV
TTIP
ClkLOS
3
TNEG/CODE
4
RNEG/LCV
5
RClk
6
RPOS/RData
7
TClk
TPOS/TData
LLoop
TVDD
TRing
TGND
JAEN
DIGI
8
9
10
11
12
13
14
RLoop
DLoop
ATM
JATx/Rx
MClk
RAOS
TAOS
ORDERING INFORMATION
PART #
PACKAGE
OPERATING TEMPERATURE RANGE
-40oC to + 85oC
XRT82D20IW
28 Lead 300 Mil Jedec SOJ
2
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
TABLE OF CONTENTS
GENERAL DESCRIPTION................................................................................................ 1
FEATURES................................................................................................................................................. 1
APPLICATIONS.......................................................................................................................................... 1
FIGURE 1. BLOCK DIAGRAM OF THE XRT82D20............................................................................................................................... 1
FIGURE 2. PINOUT OF THE XRT82D20............................................................................................................................................. 2
ORDERING INFORMATION .............................................................................................................................. 2
TABLE OF CONTENTS ............................................................................................................ I
PIN DESCRIPTIONS......................................................................................................... 3
FIGURE 3. INTERFACE TIMING DIAGRAM IN BOTH SINGLE-RAIL AND DUAL-RAIL MODE, WITH DIGI (PIN 17) = “0” ............................... 6
FIGURE 4. INTERFACE TIMING DIAGRAM IN DUAL-RAIL MODE ONLY, WITH DIGI (PIN 17) = “1” ........................................................... 6
ELECTRICAL CHARACTERISTICS................................................................................. 7
TABLE 1: RECEIVER CHARACTERISTICS ............................................................................................................................................ 7
TABLE 2: TRANSMITTER CHARACTERISTICS ....................................................................................................................................... 7
TABLE 3: 3.3V POWER CONSUMPTION INCLUDING LINE POWER DISSIPATION, TRANSMISSION AND RECEIVE PATHS ALL ACTIVE .......... 7
TABLE 4: 5V POWER CONSUMPTION INCLUDING LINE POWER DISSIPATION, TRANSMISSION AND RECEIVE PATHS ALL ACTIVE ............. 8
TABLE 5: AC ELECTRICAL CHARACTERISTICS .................................................................................................................................. 8
TABLE 6: DC ELECTRICAL CHARACTERISTICS ................................................................................................................................... 9
ABSOLUTE MAXIMUM RATINGS.............................................................................................................. 9
FIGURE 5. RECEIVER MAXIMUM JITTER TOLERANCE, TEST CONDITIONS: TEST PATTERN 215-1, (-6DB) CABLE LOSS ....................... 10
FIGURE 6. RECEIVER JITTER TRANSFER FUNCTION (JITTER ATTENUATOR DISABLED), TEST CONDITIONS: TEST PATTERN 215-1, INPUT JIT-
TER 0.5UIP-P ................................................................................................................................................................ 10
FIGURE 7. RECEIVER JITTER TRANSFER FUNCTION (JITTER ATTENUATOR ENABLED) TEST CONDITIONS: TEST PATTERN 215-1, INPUT JITTER
75% OF MAXIMUM JITTER TOLERANCE........................................................................................................................... 11
SYSTEM DESCRIPTION................................................................................................. 12
1.0 THE RECEIVE SECTION....................................................................................................................... 12
1.1 JITTER ATTENUATOR ..................................................................................................................................... 12
1.2 THE TRANSMIT SECTION................................................................................................................................ 12
FIGURE 8. ILLUSTRATION ON HOW THE XRT82D20 SAMPLES THE DATA ON THE TPOS AND TNEG INPUT PINS................................ 13
1.3 THE PULSE SHAPING CIRCUIT ...................................................................................................................... 13
FIGURE 9. ILLUSTRATION OF THE ITU-T G.703 PULSE TEMPLATE FOR E1 APPLICATION .................................................................. 14
1.4 INTERFACING THE TRANSMIT SECTION OF THE XRT82D20 TO THE LINE.............................................. 15
FIGURE 10. ILLUSTRATION OF HOW TO INTERFACE THE XRT82D20 TO THE LINE FOR 75 OHM APPLICATIONS AND 3.3V OPERATION ONLY
15
FIGURE 11. ILLUSTRATION OF HOW TO INTERFACE THE XRT82D20 TO THE LINE FOR 120 OHM APPLICATIONS AND 3.3V OPERATION ONLY
16
1.5 INTERFACING THE RECEIVE SECTION TO THE LINE.................................................................................. 17
FIGURE 12. RECOMMENDED SCHEMATIC FOR TRANSFORMER-COUPLING THE XRT82D20 TO THE LINE FOR 75 OHM APPLICATIONS AND 5
V OPERATION ONLY ....................................................................................................................................................... 17
FIGURE 13. RECOMMENDED SCHEMATIC FOR TRANSFORMER-COUPLING THE XRT82D20 TO THE LINE FOR 120 OHM APPLICATIONS AND 5
V OPERATION ONLY ....................................................................................................................................................... 18
1.6 CAPACITIVELY-COUPLING THE RECEIVE SECTION(S) OF THE XRT82D20 TO THE LINE...................... 19
FIGURE 14. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 75 OHM APPLICATION AND 3.3V SUPPLY ..................................... 19
FIGURE 15. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 120 OHM APPLICATION AND 3.3V SUPPLY ................................... 20
FIGURE 16. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 75 OHM APPLICATION AND 5V SUPPLY ........................................ 21
FIGURE 17. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 120 OHM APPLICATION AND 5V SUPPLY ...................................... 22
2.0 DIAGNOSTIC FEATURES..................................................................................................................... 23
2.1 THE LOCAL LOOP-BACK MODE .................................................................................................................... 23
FIGURE 18. ILLUSTRATION OF THE ANALOG LOCAL LOOP-BACK WITHIN THE XRT82D20.................................................................. 23
2.2 THE REMOTE LOOP BACK MODE.................................................................................................................. 24
FIGURE 19. ILLUSTRATION OF THE REMOTE LOOP-BACK PATH, WITHIN THE XRT82D20................................................................... 24
PACKAGE OUTLINE DRAWING.................................................................................... 25
REVISION HISTORY ..................................................................................................................................... 26
I
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
PIN DESCRIPTIONS
PIN #
SYMBOL
TYPE
DESCRIPTION
1
RLOS
O
Receiver Loss of Signal: This pin toggles Low to indicate the loss of signal at the
receive inputs.
2
3
ClkLOS
O
I
Receiver Loss of Clock: With MuteRx=1, this pin will toggle low to indicate a loss
of clock has occurred when the receive signal is lost (RLOS=0). When RLOS=0, no
transitions occur on RClk, RPOS/RData and RNEG outputs.
TNEG/
CODE
Transmitter Negative Data Input/Coding Select: With Jitter Attenuator enabled
(pin 18=1), input activity on this pin determines whether the device is configured to
operate in single-rail or dual-rail mode. With n-rail transmit data applied to this pin,
the device is automatically configured to operate in dual-rail mode for both transmit
input and receive output.
If this pin is tied high for more than 16 clock cycles, the device is configured to oper-
ate in single-rail mode with HDB3 encoding and decoding functions enabled.
If this pin is tied low for more than 16 clock cycles, the device is configured to oper-
ate in single-rail mode with AMI encoding and decoding functions enabled. (internal
pull-down).
4
RNEG/LCV
O
Receive Negative Data/Line Code Violation Output:
If the device is configured in Dual-rail mode with n-rail data applied to pin 3, then the
receive negative data will be output through this pin.
If the device is configured in Single-rail mode and operate with HDB3 coding
enabled, HDB3 code violation will be detected and cause this pin to go high.
If the device is configured in Single-rail mode and with AMI coding selected, every
bipolar violation will be reported at this pin.
5
6
RClk
O
O
Receive Clock:
Output receive clock signal to the terminal equipment.
RPOS/
RData
Receive Positive/ Data Output:
In Dual-rail mode, this signal is the p-rail receive output data. In Single-rail mode,
this signal is the receive output data.
7
8
TClk
I
I
Transmitter Clock Input:
Input clock signal (2.048 MHz ± 50ppm)
TPOS/
TData
Transmit Positive / Data Input:
In Dual-rail mode, this signal is the p-rail transmit input data. In Single-rail mode,
this signal is the transmit input data.
9
LLoop
RLoop
I
Local Loop back enable (active low):
Tie this pin low to enable analog Local Loop-back.In local loop-back mode, transmit
output data is looped back to the input of the receiver.Input signal at RTIP and
RRing are ignored. Local Loop-back has priority over Remote and Digital Loop-
back mode. See “Section 2.2, The Remote Loop Back Mode” on page 24
for more details. (internal pull-up).
10
I
Remote Loop Back Enable (active low):
Connect this pin to ground to enable Remote Loop-back. In Remote Loop-back
mode, transmit data at TPOS/TData and TNEG are ignored. See “Section 2.2,
The Remote Loop Back Mode” on page 24 for more details. (internal pull-
up).
3
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
PIN #
SYMBOL
TYPE
DESCRIPTION
11
DLoop
I
Digital Loop Back enable (active low):
Connect this pin to ground to enable Digital Local Loop-back.In Digital loop-back
mode, transmit input data after the encoder is looped back to the jitter attenuator (if
selected) and to the receive decoder. Input data at RTIP and RRing are ignored in
this mode. (internal pull-up). In this mode, the XRT82D20 can operate only as a jit-
ter attenuator.
12
13
ATM
I
I
Alarm Test Mode (Active-Low):
Connect this pin to ground to force ClkLOS, RLOS = 0 and LCV = 1 for testing with-
out affecting data transmission. (internal pull-up)
RAOS
Receive All Ones:
With this pin tied to High, an all “1’s” signal is inserted to the receiver output at
RPOS and RNEG/RData using MCLK as timing reference. This control has priority
over Digital Loop-back if both are enabled. (internal pull-down).
14
15
TAOS
MClk
I
I
Transmit All Ones:
With this pin tied High, an AMI encoded all “1’s” signal is sent to the transmit output
using MCLK as timing reference. This control has priority over Remote Loop-back if
both are enabled. (internal pull-down).
Master Clock Input:
This signal is an independent 2.048 MHz clock with accuracy better than + 50 ppM
and duty cycle within 40% to 60%. The function of MClk is to provide timing source
for the PLL clock recovery circuit, reference clock to insert all “1’s” data in the trans-
mit as well as receive paths. This signal must be available for the device to operate.
16
JATx/Rx
(DR/SR)
I
Jitter Attenuator Path Select:
With the jitter attenuator enabled, (pin 18 =”1”), tie this pin “High” to select the jitter
attenuator in the transmit path and tie it “Low” to select in the receive path. Data
input/output format is then controlled automatically by the status of the TNEG input.
If TNEG data is present the device operates in Dual-rail data mode.
Dual-Rail/Single-Rail Select:
With the jitter attenuator disabled, (pin 18 =”0”), tie this pin “High” to select Dual-Rail
data format and tie it “Low” to select Single-Rail data format. (internal pull-down)
17
DIGI
I
Digital Interface:
With this pin tied Low, input data at TPOS/TData and TNEG/CODE is active-high
and will be sampled by TClk on the falling edge, while active-high RPOS/RData and
RNEG output data are updated on the falling edge of RClk. See Figure 3 and 4 for
details.
With his pin tied high and in Dual-rail mode, transmit input accepts active-low
TPOS/TData and TNEG/CODE data and will be sampled by TClk on the falling
edge, while RPOS/RData and RNEG/LCV are active-low, data is updated on the
rising edge of RClk. (internal pull-down).
18
JAEN
I
Jitter Attenuator Enable (active high):
Connect this pin high to enable the jitter attenuation function. Jitter Attenuator Path
select is determined by the pin 16 setting. (internal pull-down)
19
20
TGND
TRing
-
Transmitter Supply Ground
O
Transmitter Ring Output:
Negative bipolar data output to the line.
21
TVDD
-
Transmit Positive Supply:
5.0 V + 5% or 3.3 V + 5%
4
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
PIN #
SYMBOL
TYPE
DESCRIPTION
22
TTIP
O
Transmitter TIP Output:
Positive bipolar data output to the line.
23
24
TxLEV
AVDD
I
Transmit Level:
Tie this pin high for 120 Ω twisted pair cable operation and tie it low for 75 Ω coaxial
cable operation (internal pull-down). This pin is only active for 5.0V operation.
-
Analog Positive Supply
5.0 V + 5% or 3.3 V+ 5%
25
26
AGND
-
I
Analog Supply Ground
MuteRx
Mute Receive Output:
With this pin tied high, a loss of receive input signal (RLOS=0) will cause ClkLOS to
go low and generate the following.
Dual-rail mode operation:
With DIGI = 0, RClk = 1, RPOS and RNEG/RData = 0
fWith DIGI = 1, RClk =0, RPOS and RNEG/RData = 1
Single-rail mode:
RClk = 1 and RData=0
(internal pull-down)
27
28
RRing
RTIP
I
I
Receive Bipolar Negative Input:
Bipolar line signal input to the receiver.
Receiver Bipolar Positive Input:
Bipolar line signal input to the receiver.
5
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 3. INTERFACE TIMING DIAGRAM IN BOTH SINGLE-RAIL AND DUAL-RAIL MODE, WITH DIGI (PIN 17) = “0”
TClk
tr
tf
TClk
TPOS/TData
or
Active High
TNEG/CODE
tTSU
tTHO
tRCD
tr
tf
RClk
tRSU
RPOS/RData
or
Active High
RNEG/LCV
tRHO
FIGURE 4. INTERFACE TIMING DIAGRAM IN DUAL-RAIL MODE ONLY, WITH DIGI (PIN 17) = “1”
TClk
tr
tf
TClk
TPOS/TData
Active Low
tTSU
tTHO
tRCD
tr
tf
RClk
tRSU
RPOS/RData
Active Low
tRHO
6
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
ELECTRICAL CHARACTERISTICS
TABLE 1: RECEIVER CHARACTERISTICS
TA = 25°C, VDD = 3.3V± 5% or 5V± 5% Unless otherwise specified
MIN.
PARAMETER
TYP.
MAX
UNIT
Vp
Receiver Sensitivity
0.7
-18
0.9
4.2
Interference Margin with -6db Cable Loss
-14
2.0
-
-
dB
Input Impedance measured between RTIP or RRing to
ground
kΩ
Recovered Clock Jitter Transfer Corner Frequency
Peaking Amplitude
-
-
18
36
kHz
dB
0.1
0.5
Jitter Attenuator Corner Frequency (-3dB curve)
-
20
40
Hz
Return Loss
51kHz-102kHz
102kHz-2048kHz
2048kHz-3072kHz
12
18
14
25
35
25
-
-
-
dB
dB
dB
TABLE 2: TRANSMITTER CHARACTERISTICS
TA = 25°C, VDD = 3.3V± 5% or 5V± 5% Unless otherwise specified
PARAMETER
MIN.
TYP.
MAX
UNIT
AMI Output Pulse Amplitude
75 Ω Application
120 Ω Application
2.14
2.70
2.37
3.00
2.60
3.30
V
V
Output Pulse Width
224
0.9
-
244
1.0
264
1.1
ns
Output Pulse Amplitude Ratio
Jitter Added by the Transmitter Output
0.025
0.050
UIpp
Output Return Loss:
51kHz -102kHz
-
-
-
20
25
20
-
-
-
dB
dB
dB
102kHz-2048kHz
2048kHz-3072kHz
TABLE 3: 3.3V POWER CONSUMPTION INCLUDING LINE POWER DISSIPATION, TRANSMISSION AND RECEIVE PATHS
ALL ACTIVE
TA = -40° to 85°C, VDD = 3.3V± 5% Unless otherwise specified
SYMBO
PARAMETER
MIN.
TYP.
MAX
UNIT
CONDITIONS
L
PC
PC
PC
Power Consumption
Power Consumption
Power Consumption
-
-
-
100
92
140
130
190
mW
mW
mW
75Ω load, operating at 50% Mark Density
120Ω load, operating at 50% Mark Density
75Ω load, operating at 100% Mark Density
150
7
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
TABLE 3: 3.3V POWER CONSUMPTION INCLUDING LINE POWER DISSIPATION, TRANSMISSION AND RECEIVE PATHS
ALL ACTIVE
TA = -40° to 85°C, VDD = 3.3V± 5% Unless otherwise specified
SYMBO
PARAMETER
MIN.
TYP.
MAX
UNIT
CONDITIONS
L
PC
Power Consumption
-
125
160
mW
120Ω load, operating at 100% Mark Den-
sity
TABLE 4: 5V POWER CONSUMPTION INCLUDING LINE POWER DISSIPATION, TRANSMISSION AND RECEIVE PATHS ALL
ACTIVE
(TA = -40° to 85°C, VDD = 5V ± 5% Unless otherwise specified)
SYMBO
PARAMETER
MIN.
TYP.
MAX
UNIT
CONDITIONS
L
PC
PC
PC
PC
Power Consumption
Power Consumption
Power Consumption
Power Consumption
-
-
-
-
160
145
200
180
210
195
260
240
mW
mW
mW
mW
75Ω load, operating at 50% Mark Density
120Ω load, operating at 50% Mark Density
75Ω load, operating at 100% Mark Density
120Ω load, operating at 100% Mark Den-
sity
TABLE 5: AC ELECTRICAL CHARACTERISTICS
TA = -40 to +85 °C, VDD = 3.3V± 5% or 5V ± 5% Unless otherwise specified
PARAMETER
SYMBOL
MClk
MClk
TClk
MIN.
TYP
2.048
50
MAX
UNITS
Clock Frequency
-50 ppm
+50ppm MHz
Clock Duty Cycle
Clock Period
40
-
60
-
%
ns
%
ns
244
50
TClk Duty Cycle
TCDU
tTSU
30
40
70
-
Transmit Data Setup Time
-
Transmit Data Hold Time
TClk Rise Time (10% /90%)
TClk Fall Time (90% / 10%)
RClk Duty Cycle
tTHO
tr
40
-
-
-
-
ns
ns
ns
%
40
40
55
-
tf
-
-
RCDU
tRSU
45
150
50
244
Receive Data Setup Time
ns
-
Receive Data Hold Time
RClk to Data Delay
tRHO
tRCD
tr
150
244
ns
ns
ns
ns
-
-
-
-
-
-
40
40
40
RClk Rise Time (10%/90%)
RClk Fall Time (90%/10%)
tf
8
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
TABLE 6: DC ELECTRICAL CHARACTERISTICS
Ta = 25°C, Vdd=3.3V ± 5% or 5V ± 5% unless otherwise specified
PARAMETER
SYMBOL
MIN
TYP
MAX
UNIT
Input High Voltage
Input Low Voltage
VIH
2.0
3.3 or 5.0
5.5
V
V
V
VIL
0.5
0
-
0.8
Output High Voltage @IOH=5mA (See Note)
VDD=3.3V
VDD=5.0v
VOH
2.4
2.4
VDD
VDD
Output Low Voltage @ IOL=5mA (See Note)
-
V
VDD=3.3V
VDD=5.0v
VOL
0
0
0.4
0.4
Input Leakage Current (except input pins with pull-up
resistors)
IL
-
0
10
uA
Input Capacitance
CI
-
-
5
-
20
20
pF
pF
Output Load Capacitance
CO
NOTE: All Digital output pins except pin 1 and pin 2, which typically source 20µA at VOH and sink -4mA at VOL
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Operating Temperature
Supply Voltage
-65 to 150°C
-40 to 85°C
-0.5V to +5.5V
9
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
15
FIGURE 5. RECEIVER MAXIMUM JITTER TOLERANCE, TEST CONDITIONS: TEST PATTERN 2 -1, (-6dB) CABLE LOSS
103
JAT Disabled
102
JAT Enabled
101
ITU-T G.823 Mask
100
10−1
100
101
102
103
104
105
(Freq.(MHz))
FIGURE 6. RECEIVER JITTER TRANSFER FUNCTION (JITTER ATTENUATOR DISABLED), TEST CONDITIONS: TEST PAT-
15
TERN 2 -1, INPUT JITTER 0.5UIP-P
2
G.735-G739 Specification
0
−2
−4
T82D20 Performance
−6
−8
−10
−12
−14
102
103
104
105
(Freq.(MHz))
10
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
FIGURE 7. RECEIVER JITTER TRANSFER FUNCTION (JITTER ATTENUATOR ENABLED) TEST CONDITIONS: TEST PAT-
15
TERN 2 -1, INPUT JITTER 75% OF MAXIMUM JITTER TOLERANCE
10
ITU.G.736 Mask
0
−10
−20
−30
T82D20 Performance
−40
−50
−60
100
101
102
103
104
105
(Freq.(MHz))
11
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
SYSTEM DESCRIPTION
The XRT82D20 is a single channel E1 transceiver that provides an electrical interface for 2.048Mbps
applications. XRT82D20 includes a receive circuit that converts an ITU-T G.703 compliant bipolar signal into a
TTL compatible logic levels. The receiver also includes an LOS (Loss of Signal) detection circuit. Similarly, in
the Transmit Direction, the Transmitter converts TTL compatible logic levels into a G.703 compatible bipolar
signal.
The XRT82D20 consists of both a Receive Section, Jitter Attenuator and Transmit Section; each of these
sections will be discussed below.
1.0 THE RECEIVE SECTION
At the receiver input, cable attenuated AMI signal can be coupled to the receiver using a capacitor or
transformer. The receive data first goes through the peak detector and data slicer for accurate data
recovery.The digital representation of the AMI signals go to the clock recovery circuit for timing recovery and
subsequently to the decoder (if selected) for HDB3 decoding before being output to the RPOS/RData and
RNEG/LCV pins. The digital data output can be in NRZ or RZ format depending the mode of operation
selected and with the option to be in dual-rail or single rail mode. Clock timing recovery of the line interface is
accomplished by means of a digital PLL scheme which has high input jitter tolerance.
The purpose of the Receive Output Interface block is to interface directly with the Receiving Terminal
Equipment. The Receive Output Interface block outputs the data (which has been recovered from the
incoming line signal) to the Receive Terminal Equipment via the RPOS and RNEG output pins.
If the Receive Section of the XRT82D20 has received a Positive-Polarity pulse, via the RTIP and
RRing input pins, then the Receive Output Interface will output a pulse at the RPOS output pin.
Similarly, if the Receive Section of the XRT82D20 has received a Negative-Polarity pulse, via the RTIP and
RRing input pins, then the Receive Output Interface will output a pulse at the RNEG output pin.
1.1
JITTER ATTENUATOR
To reduce frequency jitter in the transmit clock or receive clock, a crystal-less jitter attenuator is provided. The
jitter attenuator can be selected either in the transmit or receive path or it can be disabled.
1.2
THE TRANSMIT SECTION
In general, the purpose of the Transmit Section (within the XRT82D20) is to accept TTL/CMOS level digital
data (from the Terminal Equipment), and to encode it into a format such that it can:
1. Be efficiently transmitted over coaxial- or twisted pair cable at the E1 data rate; and
2. Be reliably received by the Remote Terminal Equipment at the other end of the E1 data link.
3. Comply with the ITU-T G.703 pulse template requirements, for E1 applications
A 2.048 MHz clock is applied to the TClk input pin and NRZ data at the TPOS and TNEG input pins. The
Transmit Input Interface circuit will sample the data, at the TPOS and TNEG input pins, upon the falling edge of
TClk, as illustrated in Figure 8 below.
12
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
FIGURE 8. ILLUSTRATION ON HOW THE XRT82D20 SAMPLES THE DATA ON THE TPOS AND TNEG INPUT PINS
tHO
tSU
TPOS
TNEG
TClk
In general, if the XRT82D20 samples a “1” on the TPOS input pin, then the Transmit Section will ultimately
generate a positive polarity pulse via the TTIP and TRing output pins (across a 1:2 transformer). Conversely, if
the XRT82D20 samples a “1” on the TNEG input pin, then the Transmit Section of the device will ultimately
generate a negative polarity pulse via the TTIP and TRing output pins (across a 1:2 transformer).
1.3
The Pulse Shaping Circuit
The purpose of the Transmit Pulse Shaping circuit is to generate Transmit Output pulses that comply with the
ITU-T G.703 Pulse Template Requirements for E1 Applications.
An illustration of the ITU-T G.703 Pulse Template Requirements is presented below in Figure 9.
With input signal as described above, the XRT82D20 will take each mark (which is provided to it via the
Transmit Input Interface block, and will generate a pulse that complies with the pulse template, presented in
Figure 9 (when measured on the secondary side of the Transmit Output Transformer).
13
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 9. ILLUSTRATION OF THE ITU-T G.703 PULSE TEMPLATE FOR E1 APPLICATION
269 ns
(244 + 25)
V = 100%
194 ns
(244 – 50)
Nominal pulse
50%
244 ns
219 ns
(244 – 25)
0%
488 ns
(244 + 244)
Note
– V corresponds to the nominal peak value.
14
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
1.4
Interfacing the Transmit Section of the XRT82D20 to the Line
ITU-T G.703 specifies that the E1 line signal can be transmitted over coaxial cable and terminated with 75Ω or
transmitted over twisted-pair and terminated with 120Ω.
In both applications (e.g., 75Ω or 120Ω, the user is advised to interface the Transmitter to the Line, in the
manner as depicted in Figure 10 and Figure 11, respectively.
FIGURE 10. ILLUSTRATION OF HOW TO INTERFACE THE XRT82D20 TO THE LINE FOR 75 OHM APPLICATIONS AND
3.3V OPERATION ONLY
75 Ω Coax
RPOS/RData
1 : 2
RTIP
RNEG/LCV
270 Ω
270 Ω
RClk
75 Ω
Signal
Source
Rxx Input
TVDD
AVDD
+3.3 V
RRING
10µF
0.1 µF
TxLEV
TGND
AGND
75 Ω Coax
2 : 1
TTIP
9.1 Ω
R Load
75 Ω
Tx Output
TNEG/CODE
TPOS/TData
TClk
9.1 Ω
TRING
15
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 11. ILLUSTRATION OF HOW TO INTERFACE THE XRT82D20 TO THE LINE FOR 120 OHM APPLICATIONS AND
3.3V OPERATION ONLY
120 Ω Twisted Pair
RPOS/RData
RNEG/LCV
RClk
1 : 2
RTIP
866 Ω
866 Ω
120 Ω
Signal
Source
Rx Input
RRING
TTIP
TVDD
AVDD
+3.3 V
10 µF
0.1 µF
TxLEV
TGND
AGND
120 Ω Twisted Pair
2 : 1
9.1 Ω
R Load
120 Ω
Tx Output
TRING
TNEG/CODE
TPOS/TData
TClk
9.1 Ω
NOTES:
1. Figure 10 and Figure 11indicate that for 3.3 V operation, both 75 Ω and 120 Ω applications, the user should
connect a 9.1Ω resistor in series between the TTIP/TRing outputs and the transformer.
2. Figure 10 and Figure 11indicate that the user should use a 2 : 1 STEP-UP Transformer.
16
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
1.5
Interfacing the Receive Section to the Line
The design of the XRT82D20 permits the user to transformer-couple the Receive Section to the line. As
mentioned earlier, the specifications for E1 require 75Ω termination loads, when transmitting over coaxial
cable, and 120Ω loads, when transmitting over twisted-pair. Figure 12 and Figure 13 present the various
methods that the user can employ to interface the Receiver of the XRT82D20 to the line.
FIGURE 12. RECOMMENDED SCHEMATIC FOR TRANSFORMER-COUPLING THE XRT82D20 TO THE LINE FOR 75 OHM
APPLICATIONS AND 5 V OPERATION ONLY
75 Ω Coax
RPOS/RData
RNEG/LCV
RClk
1 : 2
RTIP
270 Ω
270 Ω
75 Ω
Signal
Source
Rx Input
TVDD
AVDD
+5 V
RRING
10 µF
0.11 µF
TxLEV
TGND
AGND
75 Ω Coax
1.36 : 1
TTIP
15.4 Ω
R Load
75 Ω
Tx Output
TNEG/CODE
TPOS/TData
TClk
15.4 Ω
TRING
17
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 13. RECOMMENDED SCHEMATIC FOR TRANSFORMER-COUPLING THE XRT82D20 TO THE LINE FOR 120
OHM APPLICATIONS AND 5 V OPERATION ONLY
120 Ω Twisted Pair
RPOS/RData
RNEG/LCV
RClk
1 : 2
RTIP
866 Ω
866 Ω
120 Ω
Signal
Source
Rx Input
RRING
TVDD
AVDD
+5 V
10 µF
0.1 µF
TxLEV
TGND
AGND
120 Ω Twisted Pair
1.36 : 1
TTIP
26.1 Ω
R Load
120 Ω
Tx Output
TNEG/CODE
TPOS/TData
TClk
26.1 Ω
TRING
NOTE: Figure 12 and Figure 13indicate that the user should use a 1.36 :1 STEP-UP transformer, when interfacing the
receiver to the line.
18
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
1.6
Capacitively-coupling the Receive Section(s) of the XRT82D20 to the line
Capacitive coupling provides a lower cost interface to the line. It must be noted that the line isolation is limited
to the breakdown voltage of the capactior versus the typical transformer isolation of 1,500 to 3,000 volts. With
a capacitor there is also no DC isolation to ground as there is with with a transformer.
Applications that are not sensitive to these issues can benefit from the lower cost approach of using capacitor
coupling on the receive input.
See Figure 14, Figure 15, Figure 16 and Figure 17 for the recommended schematics for capacitively
coupling the receiver to the line.
FIGURE 14. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 75 OHM APPLICATION AND 3.3V SUPPLY
75 Ω Coax
RPOS/RData
RTIP
RNEG/LCV
37.4 Ω
0.1 µF
RClk
75 Ω
Signal
Source
Rx Input
37.4 Ω
TVDD
0.1 µF
+3.3 V
AVDD
RRING
10µF
0.1µF
TxLEV
TGND
AGND
75 Ω Coax
2:1
TTIP
9.1 Ω
Tx Output
R Load
75 Ω
TNEG/CODE
TPOS/TData
TClk
9.1 Ω
TRING
NOTE: Resistive divider attenuates the input signal by one-half for both 75 Ω and 120 Ω applications.
19
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 15. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 120 OHM APPLICATION AND 3.3V SUPPLY
120 Ω Twisted Pair
RPOS/RData
RNEG/LCV
RClk
RTIP
30.1 Ω
0.1 µF
0.1 µF
Rx Input
120 Ω
Signal
Source
60.4 Ω
TVDD
AVDD
30.1 Ω
+3.3 V
RRING
10 µF
0.1µF
TxLEV
TGND
AGND
120 Ω Twisted Pair
2:1
TTIP
9.1 Ω
Tx Output
R Load
120 Ω
TNEG/CODE
TPOS/TData
TClk
9.1 Ω
TRING
NOTE: Resistive divider attenuates the input signal by one-half for both 75 Ω and 120 Ω applications.
20
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
FIGURE 16. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 75 OHM APPLICATION AND 5V SUPPLY
75 Ω Coax
RPOS/RData
RTIP
RNEG/LCV
0.1 µF
RClk
75 Ω
Signal
Source
Rx Input
37.4 Ω
TVDD
0.1 µF
AVDD
RRING
+5 V
10 µF
0.1 µF
TxLEV
75 Ω Coax
1.36:1
TGND
AGND
TTIP
15.4 Ω
Tx Output
R Load
75 Ω
TNEG/CODE
TPOS/TData
TClk
15.4 Ω
TRING
NOTE: Resistive divider attenuates the input signal by one-half for both 75 Ω and 120 Ω applications.
21
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
FIGURE 17. CAPACITIVELY-COUPLING THE RECEIVE SECTION FOR 120 OHM APPLICATION AND 5V SUPPLY
120 Ω Twisted Pair
RPOS/RData
RNEG/LCV
RClk
RTIP
30.1 Ω
0.1 µF
0.1 µF
Rx Input
120 Ω
Signal
Source
60.4 Ω
TVDD
AVDD
30.1 Ω
+5 V
RRING
10 µF
0.1 µF
TxLEV
TGND
AGND
120 Ω Twisted Pair
1.36:1
TTIP
26.1 Ω
Tx Output
R Load
120 Ω
TNEG/CODE
TPOS/TData
TClk
26.1 Ω
TRING
NOTE: Resistive divider attenuates the input signal by one-half for both 75 Ω and 120 Ω applications.
22
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
2.0 DIAGNOSTIC FEATURES
REV.1.0.8
In order to support diagnostic operations, the XRT82D20 supports the following loop-back modes:
• Local Loopback
• Remote Loopback
• Digital Loopback
Each of these loop-back modes will be discussed below.
2.1
The Local Loop-Back Mode
When the XRT82D20 is configured to operate in the Local Loop-Back Mode, the XRT82D20 will ignore any
signals that are input to the RTIP and RRing input pins. The Transmitting Terminal Equipment will transmit
data into the XRT82D20 via the TPOS, TNEG and TClk input pins. This data will be processed through the
Transmit Terminal Input Interface and the Pulse Shaping circuit. Finally, this data will be output to the line via
the TTIP and TRing output pins. Additionally, this data (which is being output via the TTIP and TRing output
pins) will be looped back into the Receiver block. As a consequence, this data will also be processed through
the entire Receive Section of the XRT82D20. After this post-loop-back data has been processed through the
Receive Section it will output, to the Near-End Receiving Terminal Equipment via the RPOS and RNEG output
pins.
Figure 18, illustrates the path that the data takes (within the XRT82D20), when the chip is configured to
operate in the Local Loop-Back Mode.
The user can configure the XRT82D20 to operate in the Local Loop-Back Mode, by pulling the LLoop input pin
(pin 9) to GND.
FIGURE 18. ILLUSTRATION OF THE ANALOG LOCAL LOOP-BACK WITHIN THE XRT82D20
TTIP
TClk
TPOS
TNEG
HDB3
Encoder
Tx Pulse
Shaper
Line
Driver
MUX
TRing
Jitter Attenuator
Local
Loopback
LOS
Detect
RLOS
Data &
Timing
Recovery
RClk
RPOS
RNEG
HDB3
Decoder
Data
Peak
RTIP
MUX
Slicer
Detector
RRing
Timing
Generator
MClk
23
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
2.2
The Remote Loop Back Mode
When the XRT82D20 is configured to operate in the Remote Loop-Back Mode, the XRT82D20 will ignore any
signals that are input to the TPOS and TNEG input pins. The XRT82D20 will receive the incoming line signals,
via the RTIP and RRing input pins. This data will be processed through the entire Receive Section (within the
XRT82D20) and will output to the Receive Terminal Equipment via the RPOS and RNEG output pins.
Additionally, this data will also be internally looped back to the Transmit Input Interface block within the
Transmit Section. At this point, this data will be routed through the remainder of the Transmit Section of the
XRT82D20 and will be transmitted out onto the line via the TTIP and TRing output pins.
Figure 19, illustrates the path that the data takes (within the XRT82D20) when the chip is configured to
operate in the Remote Loop-Back Mode.
FIGURE 19. ILLUSTRATION OF THE REMOTE LOOP-BACK PATH, WITHIN THE XRT82D20
TTIP
TClk
TPOS
TNEG
HDB3
Encoder
Tx Pulse
Shaper
Line
Driver
MUX
TRing
Jitter Attenuator
Remote
Loopback
LOS
RLOS
Detect
Data &
Timing
Recovery
RClk
RPOS
RNEG
HDB3
Decoder
Data
Slicer
Peak
Detector
RTIP
RRing
MUX
Timing
Generator
MClk
NOTE: During Remote Loop-Back operation, any data which is input via the RTIP and RRING input pins, will also be output
to the Terminal Equipment, via the RPOS and RNEG output pins.
24
XRT82D20
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REV.1.0.8
PACKAGE OUTLINE DRAWING
25
XRT82D20
REV. 1.0.8
SINGLE CHANNEL E1 LINE INTERFACE UNIT
REVISION HISTORY
Rev. 1.0.6 corrections to figures, remove values from pull-up/down resistors, correct formating of ±.
Rev. 1.0.7 Minor edits of figures and text. Added 4 new figures 14, 15, 16 and 17, showing capacitive coupling
of the receiver to the line.
Rev. 1.0.8 Edit Pin 9 and 10 as internal pull-up. Updated new format with new Exar logo.
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to
improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any
circuits described herein, conveys no license under any patent or other right, and makes no representation that
the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration
purposes and may vary depending upon a user’s specific application. While the information in this publication
has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the
failure or malfunction of the product can reasonably be expected to cause failure of the life support system or
to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless
EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has
been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately
protected under the circumstances.
Copyright 2006 EXAR Corporation
Datasheet August 2006.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
26
相关型号：
XRT82L24AIV-F
PCM Transceiver, 1-Func, CEPT PCM-30/E-1, CMOS, PQFP100, 14 X 14 MM, 1.4 MM HEIGHT, GREEN, TQFP-100
EXAR
XRT82L38IV
PCM Transceiver, 1-Func, CEPT PCM-30/E-1, CMOS, PQFP144, 20 X 20 MM, 1.40 MM HEIGHT, THERMALLY ENHANCED, TQFP-144
EXAR
XRT83L30IV-F
PCM Transceiver, 1-Func, CEPT PCM-30/E-1, PQFP64, 10 X 10 MM, 1.40 MM HEIGHT, GREEN, TQFP-64
EXAR
©2020 ICPDF网 联系我们和版权申明