FOD2711AV [FAIRCHILD]
Optically Isolated Error Amplifier; 光隔离误差放大器型号: | FOD2711AV |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | Optically Isolated Error Amplifier |
文件: | 总15页 (文件大小:305K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
August 2008
FOD2711
Optically Isolated Error Amplifier
Features
Description
■ Optocoupler, precision reference and error amplifier in
The FOD2711 Optically Isolated Amplifier consists of the
popular RC431A precision programmable shunt refer-
ence and an optocoupler. The optocoupler is a gallium
arsenide (GaAs) light emitting diode optically coupled to
a silicon phototransistor. The reference voltage toler-
ance is 1ꢀ. The current transfer ratio (CTR) ranges from
100ꢀ to 200ꢀ.
single package
■ 1.240V 1ꢀ reference
■ CTR 100ꢀ to 200ꢀ
■ 5,000V RMS isolation
■ UL approval E90700, Volume 2
CSA approval 1296837
It is primarily intended for use as the error amplifier/
reference voltage/optocoupler function in isolated AC to
DC power supplies and dc/dc converters.
VDE approval 40002463
BSI approval 8702, 8703
Applications
■ Power supplies regulation
■ DC to DC converters
When using the FOD2711, power supply designers can
reduce the component count and save space in tightly
packaged designs. The tight tolerance reference elimi-
nates the need for adjustments in many applications.
The device comes in a 8-pin dip white package.
Functional Bock Diagram
Package Outlines
NC
LED
1
8
8
1
C
E
FB
2
3
4
7
6
5
COMP
GND
8
8
NC
1
1
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
Pin Definitions
Pin Number
Pin Name
Pin Description
1
2
3
4
5
6
7
8
NC
C
Not connected
Phototransistor Collector
Phototransistor Emitter
Not connected
E
NC
GND
COMP
FB
Ground
Error Amplifier Compensation. This pin is the output of the error amplifier.*
Voltage Feedback. This pin is the inverting input to the error amplifier
Anode LED. This pin is the input to the light emitting diode.
LED
*The compensation network must be attached between pins 6 and 7.
Typical Application
FAN4803
PWM
Control
V1
VO
FOD2711
2
3
8
6
7
R1
R2
5
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
2
Absolute Maximum Ratings (T = 25°C unless otherwise specified)
A
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Symbol
Parameter
Value
Units
T
Storage Temperature
-40 to +125
°C
°C
STG
T
Operating Temperature
Lead Solder Temperature
Input Voltage
-40 to +85
OPR
T
260 for 10 sec.
°C
SOL
V
13.2
20
V
LED
LED
I
Input DC Current
mA
V
V
V
Collector-Emitter Voltage
Emitter-Collector Voltage
Collector Current
30
CEO
7
V
ECO
I
50
mA
mW
mW
mW
C
(1)
PD1
PD2
PD3
Input Power Dissipation
145
85
(2)
Transistor Power Dissipation
(3)
Total Power Dissipation
145
Notes:
1. Derate linearly from 25°C at a rate of 2.42mW/°C
2. Derate linearly from 25°C at a rate of 1.42mW/°C.
3. Derate linearly from 25°C at a rate of 2.42mW/°C.
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
3
Electrical Characteristics (T = 25°C unless otherwise specified)
A
Input Characteristics
Symbol
Parameter
Test Conditions
Min. Typ.* Max. Unit
V
LED Forward Voltage
Reference Voltage
-40°C to +85°C
25°C
I
= 10mA, V
= V (Fig. 1)
1.5
V
F
LED
COMP
FB
V
V
= V , I
= 10mA (Fig.1)
REF
COMP
FB LED
1.221
1.259
V
1.228 1.240 1.252
V
Deviation of V
Temperature
Over
T = -40 to +85°C
4
12
mV
REF (DEV)
REF
(4)
A
∆V
/
Ratio of Vref Variation
to the Output of the Error
Amplifier
I
= 10 mA, V
= V to 12V
REF
-1.5
-2.7 mV/V
REF
LED
COMP
∆V
(Fig. 2)
COMP
I
Feedback Input Current
I
= 10mA, R1 = 10kΩ (Fig. 3)
0.15
0.15
0.5
0.3
µA
µA
REF
LED
I
Deviation of I
Over
T = -40°C to +85°C
A
REF (DEV)
REF
(4)
Temperature
I
Minimum Drive Current
V
V
= V (Fig. 1)
55
80
µA
µA
LED (MIN)
COMP
FB
I
Off-State Error Amplifier
Current
= 6V, V = 0 (Fig. 4)
0.001
0.1
(OFF)
LED
FB
| Z
|
Error Amplifier Output
Impedance
V
= V , I = 0.1mA to 15mA,
FB LED
0.25
Ω
OUT
COMP
(5)
f<1 kHZ)
Output Characteristics
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
I
Collector Dark Current
V
= 10V (Fig. 5)
50
nA
V
CEO
CE
BV
BV
Emitter-Collector Voltage Breakdown
Collector-Emitter Voltage Breakdown
I = 100µA
7
ECO
CEO
E
I = 1.0mA
70
V
C
Transfer Characteristics
Parameter
Symbol
Test Conditions
Min.
Typ.
Max.
Unit
CTR
Current Transfer Ratio
I
= 10mA, V
= V ,
FB
100
200
%
LED
COMP
V
= 5V (Fig. 6)
CE
V
Collector-Emitter Saturation
Voltage
I
= 10mA, V
= V
0.4
V
CE (SAT)
LED
COMP
FB,
I = 2.5mA (Fig. 6)
C
Notes:
4. The deviation parameters V
and I
are defined as the differences between the maximum and
REF(DEV)
REF(DEV)
minimum values obtained over the rated temperature range. The average full-range temperature coefficient of the
reference input voltage, ∆V , is defined as:
REF
{VREF(DEV)/VREF(TA = 25°C)} × 106
∆VREF (ppm/°C) = ----------------------------------------------------------------------------------------------------
∆TA
where ∆T is the rated operating free-air temperature range of the device.
A
5. The dynamic impedance is defined as |Z
| = ∆V
/ ∆I
. When the device is operating with two external
OUT
COMP
LED
resistors (see Figure 2), the total dynamic impedance of the circuit is given by:
∆V R1
ZOUT, TOT = ------- ≈ ZOUT × 1 + -------
∆I
R2
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
4
Electrical Characteristics (Continued) (T = 25°C unless otherwise specified)
A
Isolation Characteristics
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
I
Input-Output Insulation
Leakage Current
RH = 45%, T = 25°C, t = 5s,
1.0
µA
I-O
A
(6)
V
= 3000 VDC
I-O
(6)
V
Withstand Insulation
Voltage
RH ≤ 50%, T = 25°C, t = 1 min.
5000
Vrms
ISO
A
(6)
12
R
Resistance (Input to Output)
V
= 500 VDC
10
Ω
I-O
I-O
Switching Characteristics
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
BW
Bandwidth
(Fig. 7)
= 0mA, Vcm = 10 V
10
kHZ
CMH
Common Mode Transient
Immunity at Output HIGH
I
,
PP
1.0
kV/µs
LED
(7)
R = 2.2kΩ (Fig. 8)
L
CML
Common Mode Transient
Immunity at Output LOW
I
= 1mA, Vcm = 10 V
1.0
kV/µs
LED
PP,
(7)
R = 2.2kΩ (Fig. 8)
L
Notes:
6. Device is considered as a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted
together.
7. Common mode transient immunity at output high is the maximum tolerable (positive) dVcm/dt on the leading edge
of the common mode impulse signal, Vcm, to assure that the output will remain high. Common mode transient
immunity at output low is the maximum tolerable (negative) dVcm/dt on the trailing edge of the common pulse
signal,Vcm, to assure that the output will remain low.
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
5
Test Circuits
I(LED)
I(LED)
8
2
3
8
2
3
VF
6
7
R1
6
7
V
V
VCOMP
VREF
R2
VREF
5
5
Figure 1. VREF, VF, ILED (min.) Test Circuit
Figure 2. ∆VREF / ∆VCOMP Test Circuit
I(LED)
I(OFF)
8
2
3
8
2
IREF
6
6
3
V(LED)
7
7
V
V
R1
5
5
Figure 3. IREF Test Circuit
Figure 4. I(OFF) Test Circuit
I(LED)
ICEO
IC
8
8
2
2
3
VCE
VCE
6
7
6
3
7
VCOMP
VREF
V
5
5
Figure 5. ICEO Test Circuit
Figure 6. CTR, VCE(sat) Test Circuit
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
6
Test Circuits (Continued)
VCC = +5V DC
IF = 10mA
47Ω
1
2
3
4
8
7
6
5
RL
1µf
VOUT
VIN
0.47V
0.1 VPP
Figure 7. Frequency Response Test Circuit
VCC = +5V DC
IF = 0mA (A)
IF = 10mA (B)
R1
2.2kΩ
1
2
3
4
8
7
6
5
VOUT
A B
VCM
_
+
10VP-P
Figure 8. CMH and CML Test Circuit
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
7
Typical Performance Curves
Fig. 9a LED Current vs. Cathode Voltage
Fig. 9b LED Current vs. Cathode Voltage
15
10
5
150
100
50
TA = 25°C
VCOMP = VFB
TA = 25°C
VCOMP = VFB
0
0
-5
-50
-100
-150
-10
-15
-1.0
-0.5
0.0
0.5
1.0
1.5
-1
0
1
2
V
– CATHODE VOLTAGE (V)
COMP
V
COMP
– CATHODE VOLTAGE (V)
Fig. 10 Reference Voltage vs. Ambient Temperature
Fig. 11 Reference Current vs. Ambient Temperature
280
ILED = 10mA
1.244
ILED = 10mA
R1 = 10 kΩ
260
240
220
200
180
160
140
120
1.242
1.240
1.238
1.236
1.234
1.232
1.230
-40
-20
0
20
– AMBIENT TEMPERATURE (°C)
A
40
60
80
100
-40
-20
0
20
40
60
80
100
T
T
– AMBIENT TEMPERATURE (°C)
A
Fig. 13 Forward Current vs. Forward Voltage
Fig. 12 Off-State Current vs. Ambient Temperature
20
15
10
V
CC = 13.2V
1000
100
10
25°C
70°C
0°C
1
5
0.1
0.9
1.0
1.1
1.2
1.3
1.4
-40
-20
0
20
40
60
80
100
T
A
– AMBIENT TEMPERATURE (°C)
V
– FORWARD VOLTAGE (V)
F
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
8
Typical Performance Curves (Continued)
Fig. 15 Collector Current vs. Ambient Temperature
Fig. 14 Dark Current vs. Ambient Temperature
10000
30
25
20
15
10
5
VCE = 5V
VCE = 10V
1000
I
LED = 20mA
100
10
1
ILED = 10mA
I
LED = 5mA
ILED = 1mA
60
0.1
-40
0
-20
0
20
40
60
80
100
0
10
20
30
40
50
70
80
90
100
T
A
– AMBIENT TEMPERATURE (°C)
T
A
– AMBIENT TEMPERATURE (°C)
Fig. 17 Saturation Voltage vs. Ambient Temperature
Fig. 16 Current Transfer Ratio vs. LED Current
0.26
VCE = 5V
140
120
100
80
0.24
0.22
0.20
0.18
0.16
0.14
0.12
0.10
0°C
25°C
70°C
60
40
-40
-20
0
20
40
60
80
100
0
5
10
15
20
25
30
35
40
45
50
T
A
– AMBIENT TEMPERATURE (°C)
I
– FORWARD CURRENT (mA)
LED
Fig. 19 Rate of Change Vref to Vcomp vs. Temperature
Fig. 18 Collector Current vs. Collector Voltage
35
30
25
20
15
10
5
TA = 25°C
-0.2
-0.4
-0.6
-0.8
-1.0
-1.2
-1.4
-1.6
ILED = 20mA
ILED = 10mA
ILED = 5mA
ILED = 1mA
0
-60
-40
-20
0
20
40
60
80
100
120
0
1
2
3
4
5
6
7
8
9
10
TEMPERATURE (°C)
V
– COLLECTOR-EMITTER VOLTAGE (V)
CE
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
9
Typical Performance Curves (Continued)
Fig. 20 Voltage Gain vs. Frequency
V
= 10V
CC
= 10mA
I
F
0
R
= 100Ω
L
-5
-10
R
L
= 1kΩ
R
=500Ω
L
-15
0.1
1
10
100
1000
FREQUENCY (kHZ)
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
10
The FOD2711
The FOD2711 is an optically isolated error amplifier. It
incorporates three of the most common elements neces-
sary to make an isolated power supply, a reference volt-
age, an error amplifier, and an optocoupler. It is
functionally equivalent to the popular RC431A shunt volt-
age regulator plus the CNY17F-3 optocoupler.
Compensation
The compensation pin of the FOD2711 provides the
opportunity for the designer to design the frequency
response of the converter. A compensation network may
be placed between the COMP pin and the FB pin. In
typical low-bandwidth systems, a 0.1µF capacitor may
be used. For converters with more stringent require-
ments, a network should be designed based on mea-
surements of the system’s loop. An excellent reference
for this process may be found in “Practical Design of
Power Supplies” by Ron Lenk, IEEE Press, 1998.
Powering the Secondary Side
The LED pin in the FOD2711 powers the secondary
side, and in particular provides the current to run the
LED. The actual structure of the FOD2711 dictates the
minimum voltage that can be applied to the LED pin: The
error amplifier output has a minimum of the reference
voltage, and the LED is in series with that. Minimum volt-
age applied to the LED pin is thus 1.24V + 1.5V = 2.74V.
This voltage can be generated either directly from the
output of the converter, or else from a slaved secondary
winding. The secondary winding will not affect regula-
tion, as the input to the FB pin may still be taken from the
output winding.
Secondary Ground
The GND pin should be connected to the secondary
ground of the converter.
No Connect Pins
The NC pins have no internal connection. They should
not have any connection to the secondary side, as this
may compromise the isolation structure.
The LED pin needs to be fed through a current limiting
resistor. The value of the resistor sets the amount of cur-
rent through the LED, and thus must be carefully
selected in conjunction with the selection of the primary
side resistor.
Photo-Transistor
The Photo-transistor is the output of the FOD2711. In a
normal configuration the collector will be attached to a
pull-up resistor and the emitter grounded. There is no
base connection necessary.
Feedback
The value of the pull-up resistor, and the current limiting
resistor feeding the LED, must be carefully selected to
account for voltage range accepted by the PWM IC, and
for the variation in current transfer ratio (CTR) of the
opto-isolator itself.
Output voltage of a converter is determined by selecting
a resistor divider from the regulated output to the FB pin.
The FOD2711 attempts to regulate its FB pin to the
reference voltage, 1.24V. The ratio of the two resistors
should thus be:
Example: The voltage feeding the LED pins is +12V, the
voltage feeding the collector pull-up is +10V, and the
PWM IC is the Fairchild KA1H0680, which has a 5V ref-
erence. If we select a 10KΩ resistor for the LED, the
maximum current the LED can see is:
RTOP
------------------------- = -------------- – 1
RBOTTOM VREF
VOUT
The absolute value of the top resistor is set by the input
offset current of 0.8µA. To achieve 1ꢀ accuracy, the
resistance of R
(12V–2.74V) / 10kΩ = 926µA.
should be:
TOP
The CTR of the opto-isolator is a minimum of 100ꢀ, and
so the minimum collector current of the photo-transistor
when the diode is full on is also 926µA. The collector
resistor must thus be such that:
V
OUT – 1.24
------------------------------- > 80 µA
RTOP
10V – 5V
----------------------------------- < 926 µA or RCOLLECTOR > 5.4KΩ;
RCOLLECTOR
select 10kΩ to allow some margin.
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
11
Package Dimensions
Through Hole
0.4" Lead Spacing
PIN 1
ID.
PIN 1
ID.
1
0.270 (6.86)
0.250 (6.35)
0.270 (6.86)
0.250 (6.35)
0.390 (9.91)
0.370 (9.40)
0.070 (1.78)
0.045 (1.14)
0.390 (9.91)
0.370 (9.40)
0.020 (0.51) MIN
0.200 (5.08)
0.140 (3.55)
0.070 (1.78)
0.045 (1.14)
0.154 (3.90)
0.120 (3.05)
0.004 (0.10) MIN
0.200 (5.08)
0.140 (3.55)
15° MAX
0.022 (0.56)
0.016 (0.41)
0.016 (0.40)
0.008 (0.20)
0.154 (3.90)
0.120 (3.05)
0.300 (7.62)
TYP
0.100 (2.54) TYP
0.022 (0.56)
0.016 (0.41)
0° to 15°
0.016 (0.40)
0.008 (0.20)
0.400 (10.16)
TYP
0.100 (2.54) TYP
Surface Mount
8-Pin DIP – Land Pattern
0.390 (9.91)
0.370 (9.40)
0.070 (1.78)
PIN 1
ID.
0.060 (1.52)
0.270 (6.86)
0.250 (6.35)
0.100 (2.54)
0.295 (7.49)
0.415 (10.54)
0.030 (0.76)
0.300 (7.62)
TYP
0.070 (1.78)
0.045 (1.14)
0.020 (0.51)
MIN
0.016 (0.41)
0.008 (0.20)
0.045 (1.14)
0.022 (0.56)
0.016 (0.41)
0.315 (8.00)
MIN
0.100 (2.54)
TYP
0.405 (10.30)
MAX.
Lead Coplanarity : 0.004 (0.10) MAX
Note:
All dimensions are in inches (millimeters)
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
12
Ordering Information
Option
Example Part Number
FOD2711A
Description
No Option
Standard Through Hole
S
SD
T
FOD2711AS
Surface Mount Lead Bend
Surface Mount; Tape and Reel
0.4" Lead Spacing
FOD2711ASD
FOD2711AT
V
FOD2711AV
VDE0884
TV
SV
SDV
FOD2711ATV
FOD2711ASV
FOD2711ASDV
VDE0884; 0.4” Lead Spacing
VDE0884; Surface Mount
VDE0884; Surface Mount; Tape and Reel
Marking Information
1
2
2711
6
V XX YY B
5
3
4
Definitions
Fairchild logo
1
Device number
2
3
VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
Two digit year code, e.g., ‘03’
4
5
6
Two digit work week ranging from ‘01’ to ‘53’
Assembly package code
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
13
Carrier Tape Specifications
D0
P0
P2
t
E
K0
F
W
W1
P
User Direction of Feed
d
D1
Symbol
Description
Dimension in mm
16.0 0.3
0.30 0.05
4.0 0.1
W
t
Tape Width
Tape Thickness
P
Sprocket Hole Pitch
Sprocket Hole Diameter
Sprocket Hole Location
Pocket Location
0
D
1.55 0.05
1.75 0.10
7.5 0.1
0
E
F
P
4.0 0.1
2
P
Pocket Pitch
12.0 0.1
10.30 0.20
10.30 0.20
4.90 0.20
1.6 0.1
A
Pocket Dimensions
0
0
0
B
K
W
Cover Tape Width
1
d
Cover Tape Thickness
0.1 max
Max. Component Rotation or Tilt
Min. Bending Radius
10°
R
30
Reflow Profile
245C, 10–30 s
300
250
200
150
100
50
260C peak
Time above 183C, <160 sec
Ramp up = 2–10C/sec
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
Time (Minute)
• Peak reflow temperature: 260C (package surface temperature)
• Time of temperature higher than 183C for 160 seconds or less
• One time soldering reflow is recommended
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
14
TRADEMARKS
The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not
intended to be an exhaustive list of all such trademarks.
PDP SPM™
The Power Franchise®
Build it Now™
CorePLUS™
CorePOWER™
CROSSVOLT™
CTL™
FPS™
Power-SPM™
PowerTrench®
Programmable Active Droop™
QFET®
F-PFS™
FRFET®
Global Power ResourceSM
Green FPS™
Green FPS™e-Series™
GTO™
TinyBoost™
TinyBuck™
TinyLogic®
TINYOPTO™
TinyPower™
TinyPWM™
TinyWire™
µSerDes™
QS™
Current Transfer Logic™
EcoSPARK®
Quiet Series™
RapidConfigure™
Saving our world, 1mW at a time™
SmartMax™
EfficentMax™
EZSWITCH™ *
IntelliMAX™
ISOPLANAR™
MegaBuck™
MICROCOUPLER™
MicroFET™
™
SMART START™
SPM®
®
STEALTH™
SuperFET™
SuperSOT™-3
SuperSOT™-6
SuperSOT™-8
SupreMOS™
MicroPak™
Fairchild®
MillerDrive™
MotionMax™
Motion-SPM™
OPTOLOGIC®
UHC®
Ultra FRFET™
UniFET™
VCX™
Fairchild Semiconductor®
FACT Quiet Series™
FACT®
FAST®
OPTOPLANAR®
FastvCore™
®
VisualMax™
SyncFET™
FlashWriter® *
®
* EZSWITCH™ and FlashWriter® are trademarks of System General Corporation, used under license by Fairchild Semiconductor.
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE
RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR
CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE
SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN,
WHICH COVERS THESE PRODUCTS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are
intended for surgical implant into the body or (b) support or sustain life,
and (c) whose failure to perform when properly used in accordance
with instructions for use provided in the labeling, can be reasonably
expected to result in a significant injury of the user.
2. A critical component in any component of a life support, device, or
system whose failure to perform can be reasonably expected to
cause the failure of the life support device or system, or to affect its
safety or effectiveness.
ANTI-COUNTERFEITING POLICY
Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com,
under Sales Support.
Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts.
Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications,
and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of
counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are
listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have
full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information.
Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide
any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our
customers to do their part in stopping this practice by buying direct or from authorized distributors.
PRODUCT STATUS DEFINITIONS
Definition of Terms
Datasheet Identification Product Status
Definition
Datasheet contains the design specifications for product development. Specifications may change in
any manner without notice.
Advance Information
Preliminary
Formative / In Design
Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild
Semiconductor reserves the right to make changes at any time without notice to improve design.
First Production
Full Production
Not In Production
Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes
at any time without notice to improve the design.
No Identification Needed
Obsolete
Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The
datasheet is for reference information only.
Rev. I35
©2003 Fairchild Semiconductor Corporation
FOD2711 Rev. 1.0.1
www.fairchildsemi.com
15
相关型号:
FOD2711SR2
Transistor Output Optocoupler, 1-Element, 5000V Isolation, SURFACE MOUNT, DIP-8
FAIRCHILD
©2020 ICPDF网 联系我们和版权申明