NM27C256V200 [FAIRCHILD]
262,144-Bit (32K x 8) High Performance CMOS EPROM; 262,144位( 32K ×8 )高性能CMOS EPROM型号: | NM27C256V200 |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | 262,144-Bit (32K x 8) High Performance CMOS EPROM |
文件: | 总11页 (文件大小:114K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
July 1998
NM27C256
262,144-Bit (32K x 8) High Performance CMOS EPROM
The NM27C256 is one member of a high density EPROM Family
which range in densities up to 4 Mb.
General Description
The NM27C256 is a 256K Electrically Programmable Read Only
Memory. It is manufactured in Fairchild’s latest CMOS split gate
EPROM technology which enables it to operate at speeds as fast
as 90 ns access time over the full operating range.
Features
■ High performance CMOS
—90 ns access time
The NM27C256 provides microprocessor-based systems exten-
■ JEDEC standard pin configuration
sive storage capacity for large portions of operating system and
— 28-pin PDIP package
application software. Its 90 ns access time provides high speed
— 32-pin chip carrier
operation with high-performance CPUs. The NM27C256 offers a
— 28-pin CERDIP package
single chip solution for the code storage requirements of 100%
■ Drop-in replacement for 27C256 or 27256
firmware-based equipment. Frequently-used software routines
are quickly executed from EPROM storage, greatly enhancing
system utility.
■ Manufacturer’s identification code
The NM27C256 is configured in the standard EPROM pinout
which provides an easy upgrade path for systems which are
currently using standard EPROMs.
Block Diagram
Data Outputs O - O
0
7
V
CC
GND
V
PP
OE
Output Enable
and Chip Enable Logic
Output
Buffers
CE/PGM
Y Decoder
Y Gating
A
- A
14
0
Address
Inputs
X Decoder
DS010833-1
1
© 1998 Fairchild Semiconductor Corporation
www.fairchildsemi.com
Connection Diagrams
27C080 27C040 27C020 27C010 27C512
27C512 27C010 27C020 27C040
27C080
DlP
NM27C256
A
A
A
A
XX/V XX/V
PP
XX/V
A
V
V
V
V
19
16
15
12
PP
PP
CC
CC
CC
CC
A
A
A
A
A
A
XX/PGM XX/PGM
A
A
A
A
A
16
15
12
16
16
18
17
14
13
18
28
27
26
25
24
23
22
21
20
19
18
17
16
15
V
CC
A
A
A
A
V
1
V
A
A
A
A
A
XX
A
A
A
A
15
12
15
12
15
12
PP
CC
14
13
8
17
14
13
17
A
2
A
A
A
A
12
14
13
14
13
14
A
A
A
A
A
A
A
A
A
A
A
A
A
O
O
O
3
A
A
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
0
1
2
13
A
A
A
A
A
4
A
A
A
A
A
8
A
9
8
9
8
9
8
9
8
9
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
5
A
A
A
A
9
6
A
11
A
A
A
A
11
11
11
11
11
7
OE
A
OE/V
A
OE
OE
OE
OE/V
PP
PP
8
A
A
A
A
10
10
10
10
10
10
9
CE/PGM
CE/PGM
CE
CE
CE/PGM CE/PGM
10
11
12
13
14
O
7
O
6
O
5
O
4
O
7
O
6
O
5
O
4
O
7
O
6
O
5
O
4
O
7
O
6
O
5
O
4
O
O
O
O
O
O
O
O
O
O
7
6
5
4
3
7
6
5
4
3
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
0
1
2
0
1
2
0
1
2
0
1
2
0
1
2
GND GND
GND
GND GND
GND
O
3
O
3
O
3
O
3
Note: Compatible EPROM pin configurations are shown in the blocks adjacent to the NM27C256 pins.
DS010833-2
Commercial Temp. Range (0°C to +70°C)
VCC = 5V ±10%
Pin Names
Description
Symbol
A0–A14
CE/PGM
OE
Parameter/Order Number Access Time (ns)
Addresses
NM27C256 Q, N, V 90
NM27C256 Q, N, V 100
NM27C256 Q, N, V 120
NM27C256 Q, N, V 150
NM27C256 Q, N, V 200
90
Chip Enable/Program
Output Enable
Outputs
100
120
150
200
O0–O7
XX
Don’t Care (during Read)
PLCC
Extended Temp. Range (-40°C to +85°C)
VCC = 5V ±10%
Parameter/Order Number Access Time (ns)
4
3
2
1 32 31 30
NM27C256 QE, NE, VE 120
NM27C256 QE, NE, VE 150
NM27C256 QE, NE, VE 200
120
150
200
5
6
7
8
29
28
27
26
25
24
23
22
21
A8
A9
A11
XX
OE
A10
CE/PGM
O7
A6
A5
A4
A3
A2
A1
A0
XX
O0
Note: Surface mount PLCC package available for commercial and extended
temperature ranges only.
9
Package Types: NM27C256 Q, N, V XXX
Q = Quartz-Windowed Ceramic DIP
N = Plastic OTP DIP
10
11
12
13
V = Surface-Mount PLCC
O6
•
•
All Packages conform to the JEDEC standard.
14 15 16 17 18 19 20
All versions are guaranteed to function for slower speeds.
DS010833-3
Top
2
www.fairchildsemi.com
ESD Protection
> 2000V
Absolute Maximum Ratings (Note 1)
All Output Voltages with
Respect to Ground
Storage Temperature
-65°C to +150°C
VCC + 1.0V to GND -0.6V
All Input Voltages except A9 with
Respect to Ground
-0.6V to +7V
-0.7V to +14V
-0.6V to +7V
Operating Range
VPP and A9 with Respect
to Ground
Range
Comm’l
Temperature
VCC
0°C to +70°C
-40°C to +85°C
+5V ±10%
+5V ±10%
VCC Supply Voltage with
Respect to Ground
Industrial
Read Operation
DC Electrical Characteristics Over Operating Range with VPP = VCC
Symbol
VIL
Parameter
Test Conditions
Min
-0.5
2.0
Max
0.8
Units
Input Low Level
V
V
VIH
Input High Level
VCC +1
0.4
VOL
Output Low Voltage
Output High Voltage
IOL = 2.1 mA
V
VOH
IOH = -2.5 mA
3.5
V
ISB1
(Note 11)
VCC Standby Current
(CMOS)
CE = VCC ±0.3V
100
µA
ISB2
ICC1
VCC Standby Current (TTL)
CE = VIH
1
mA
mA
VCC Active Current
TTL Inputs
CE = OE = VIL,f=5 MHz
Inputs = VIH or VIL, I/O = 0 mA
35
IPP
VPP
ILI
VPP Supply Current
VPP Read Voltage
VPP = VCC
10
VCC
1
µA
V
VCC - 0.7
-1
Input Load Current
Output Leakage Current
VIN = 5.5V or GND
VOUT = 5.5V or GND
µA
µA
ILO
-10
10
AC Electrical Characteristics Over Operating Range with VPP = VCC
Symbol
Parameter
90
100
120
150
200
Units
Min Max Min Max Min Max Min Max Min Max
tACC
tCE
Address to Output Delay
CE to Output Delay
OE to Output Delay
90
90
35
30
100
100
50
120
120
50
150
150
50
200
200
50
ns
tOE
tDF
(Note 2)
Output Disable to
Output Float
30
35
45
45
tOH
(Note 2)
Output Hold from
Addresses,
0
0
0
0
0
CE or OE, Whichever
Occurred First
Capacitance (Note 2) TA = +25˚C, f = 1 MHz
Symbol
CIN
Parameter
Conditions Typ Max Units
Input Capacitance
VIN = 0V
6
9
12
12
pF
pF
COUT
Output Capacitance VOUT = 0V
3
www.fairchildsemi.com
AC Test Conditions
Output Load
1 TTL Gate and CL = 100 pF (Note 8)
Input Rise and Fall Times
Input Pulse Levels
≤ 5 ns
0.45 to 2.4V
Timing Measurement Reference Level (Note 10)
Inputs
Outputs
0.8V and 2.0V
0.8V and 2.0V
AC Waveforms (Note 6) (Note 7) (Note 9)
2.0V
ADDRESSES
ADDRESSES VALID
0.8V
2.0V
CE
0.8V
tCE
tCE
(Notes 4, 5)
2.0V
OE
0.8V
tOE
(Note 3)
tDF
(Notes 4, 5)
2.0V
Hi-Z
Hi-Z
OUTPUT
0.8V
VALID OUTPUT
tACC
(Note 3)
tOH
DS010833-4
Note 1: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Note 2: This parameter is only sampled and is not 100% tested.
Note 3: OE may be delayed up to tACC - tOE after the falling edge of CE without impacting tACC
.
Note 4: The tDF and tCF compare level is determined as follows:
High to TRI-STATE®, the measured VOH1 (DC) - 0.10V;
Low to TRI-STATE, the measured VOL1 (DC) + 0.10V.
Note 5: TRI-STATE may be attained using OE or CE.
Note 6: The power switching characteristics of EPROMs require careful device decoupling. It is recommended that at least a 0.1 µF ceramic capacitor be used on every device
between VCC and GND.
Note 7: The outputs must be restricted to VCC + 1.0V to avoid latch-up and device damage.
Note 8: TTL Gate: IOL = 1.6 mA, IOH = -400 µA.
CL = 100 pF includes fixture capacitance.
Note 9: VPP may be connected to VCC except during programming.
Note 10: Inputs and outputs can undershoot to -2.0V for 20 ns Max.
Note 11: CMOS inputs: VIL = GND ±0.3V, VIH = VCC ±0.3V.
Programming Characteristics (Note 12) (Note 13) (Note 14) (Note 15)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
4
www.fairchildsemi.com
Programming Characteristics (Note 12) (Note 13) (Note 14) (Note 15) (Continued)
Symbol
tAS
Parameter
Address Setup Time
OE Setup Time
Conditions
Min
Typ
Max
Units
µs
1
1
1
1
1
0
1
0
tOES
tVPS
tVCS
tDS
µs
VPP Setup Time
µs
VCC Setup Time
Data Setup Time
Address Hold Time
Data Hold Time
µs
µs
tAH
µs
tDH
µs
tDF
Output Enable to Output
Float Delay
CE = VIL
60
ns
tPW
tOE
IPP
Program Pulse Width
Data Valid from OE
45
50
105
100
30
µs
ns
CE = VIL
CE = VIL
VPP Supply Current
mA
during Programming Pulse
ICC
TA
VCC Supply Current
50
30
mA
°C
V
Temperature Ambient
Power Supply Voltage
Programming Supply Voltage
Input Rise, Fall Time
20
6.25
12.5
5
25
6.5
VCC
VPP
tFR
6.75
13.0
12.75
V
ns
V
VIL
Input Low Voltage
0.0
4.0
0.45
VIH
tIN
Input High Voltage
2.4
0.8
0.8
V
Input Timing Reference Voltage
Output Timing Reference Voltage
2.0
2.0
V
tOUT
V
Programming Waveforms (Note 14)
PROGRAM
VERIFY
PROGRAM
2.0V
ADDRESSES
ADDRESS N
0.8V
tAS
tAH
2.0V
DATA IN STABLE
ADD N
DATA OUT VALID
ADD N
DATA
VCC
0.8V
tDS
tDH
tDF
5.25V
tVCS
12.75V
VPP
tVPS
2.0V
0.8V
CE
OE
tOES
tOE
tPW
2.0V
0.8V
DS010833-5
Note 12: Fairchild’s standard product warranty applies to devices programmed to specifications described herein.
Note 13: VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP. The EPROM must not be inserted into or removed from a board with
voltage applied to VPP or VCC
.
Note 14: The maximum absolute allowable voltage which may be applied to the VPP pin during programming is 14V. Care must be taken when switching the VPP supply to
prevent any overshoot from exceeding this 14V maximum specification. At least a 0.1 µF capacitor is required across VPP, VCC to GND to suppress spurious voltage transients
which may damage the device.
Note 15: During power up the PGM pin must be brought high (≥ VIH) either coincident with or before power is applied to VPP
.
5
www.fairchildsemi.com
Turbo Programming Algorithm Flow Chart
VCC = 6.5V VPP = 12.75V
n = 0
ADDRESS = FIRST LOCATION
PROGRAM ONE 50µs PULSE
INCREMENT n
NO
YES
FAIL
DEVICE
FAILED
VERIFY
BYTE
n = 10?
PASS
INCREMENT
ADDRESS
n = 0
LAST
ADDRESS
?
NO
YES
ADDRESS = FIRST LOCATION
FAIL
VERIFY
BYTE
PASS
PROGRAM ONE
50 µs
INCREMENT
ADDRESS
PULSE
LAST
NO
ADDRESS
?
YES
CHECK ALL BYTES
1ST: VCC = VPP = 6.0V
2ND: VCC = VPP = 4.3V
Note:
The standard National Semiconductor algorithm may also be used but it will have longer programming time.
DS010833-6
FIGURE 1.
6
www.fairchildsemi.com
The EPROM is in the programming mode when the VPP power
supply is at 12.75V and OE is at VIH. It is required that at least a
0.1 µF capacitor be placed across VPP, VCC to ground to suppress
spurious voltage transients which may damage the device. The
data to be programmed is applied 8 bits in parallel to the data
output pins. The levels required for the address and data inputs
are TTL.
Functional Description
DEVICE OPERATION
The six modes of operation of the EPROM are listed in Table 1. It
should be noted that all inputs for the six modes are at TTL levels.
The power supplies required are VCC and VPP. The VPP power
supply must be at 12.75V during the three programming modes,
andmustbeat5Vintheotherthreemodes. TheVCC powersupply
must be at 6.5V during the three programming modes, and at 5V
in the other three modes.
Whentheaddressanddataarestable,anactivelow,TTLprogram
pulse is applied to the CE/PGM input. A program pulse must be
applied at each address location to be programmed. The EPROM
is programmed with the Turbo Programming Algorithm shown in
Figure 1. Each Address is programmed with a series of 50 µs
pulses until it verifies good, up to a maximum of 10 pulses. Most
memorycellswillprogram withasingle50µspulse.(Thestandard
National Semiconductor Algorithm may also be used but it will
have longer programming time.)
Read Mode
The EPROM has two control functions, both of which must be
logically active in order to obtain data at the outputs. Chip Enable
(CE/PGM) is the power control and should be used for device
selection. Output Enable (OE) is the output control and should be
used to gate data to the output pins, independent of device
selection. Assuming that addresses are stable, address access
time (tACC) is equal to the delay from CE to output (tCE). Data is
available at the outputs tOE after the falling edge of OE, assuming
that CE/PGM has been low and addresses have been stable for
The EPROM must not be programmed with a DC signal applied to
the CE/PGM input.
Programming multiple EPROM in parallel with the same data can
be easily accomplished due to the simplicity of the programming
requirments.LikeinputsoftheparallelEPROMmaybeconnected
together when they are programmed with the same data. A low
level TTL pulse applied to the CE/PGM input programs the
paralleled EPROM.
at least tACC –tOE
.
Standby Mode
The EPROM has a standby mode which reduces the active power
dissipation by over 99%, from 385 mW to 0.55 mW. The EPROM
is placed in the standby mode by applying a CMOS high signal to
the CE/PGM input. When in standby mode, the outputs are in a
high impedance state, independent of the OE input.
Program Inhibit
Programming multiple EPROMs in parallel with different data is
also easily accomplished. Except for CE/PGM, all like inputs
(including OE) of the parallel EPROMs may be common. A TTL
low level program pulse applied to an EPROM’s CE/PGM input
withVPP at12.75VwillprogramthatEPROM. ATTLhighlevelCE/
PGM input inhibits the other EPROMs from being programmed.
Output Disable
The EPROM is placed in output disable by applying a TTL high
signal to the OE input. When in output disable all circuitry is
enabled, except the outputs are in a high impedance state (TRI-
STATE).
Program Verify
Averifyshouldbeperformedontheprogrammedbitstodetermine
whether they were correctly programmed. The verify may be
performed with VPP at 12.75V. VPP must be at VCC, except during
programming and program verify.
Output OR-Typing
Because the EPROM is usually used in larger memory arrays,
Fairchild has provided a 2-line control function that accommo-
dates this use of multiple memory connections. The 2-line control
function allows for:
AFTER PROGRAMMING
Opaque labels should be placed over the EPROM window to
prevent unintentional erasure. Covering the window will also
preventtemporaryfunctionalfailureduetothegenerationof photo
currents.
1. the lowest possible memory power dissipation, and
2. complete assurance that output bus contention will not
occur.
To most efficiently use these two control lines, it is recommended
that CE/PGM be decoded and used as the primary device select-
ing function, while OE be made a common connection to all
devices in the array and connected to the READ line from the
system control bus. This assures that all deselected memory
devices are in their low power standby modes and that the output
pinsareactiveonlywhendataisdesiredfromaparticularmemory
device.
MANUFACTURER’S IDENTIFICATION CODE
The EPROM has a manufacturer’s identification code to aid in
programming. When the device is inserted in an EPROM pro-
grammer socket, the programmer reads the code and then
automatically calls up the specific programming algorithm for the
part. This automatic programming control is only possible with
programmers which have the capability of reading the code.
The Manufacturer’s Identification code, shown in Table 2, specifi-
cally identifies the manufacturer and device type. The code for
NM27C256 is “8F04”, where “8F” designates that it is made by
Fairchild Semiconductor, and “04” designates a 256K part.
Programming
CAUTION:Exceeding14Vonpin1(VPP)willdamagetheEPROM.
Initially, and after each erasure, all bits of the EPROM are in the
“1’s” state. Data is introduced by selectively programming “0’s”
into the desired bit locations. Although only “0’s” will be pro-
grammed, both “1’s” and “0’s” can be presented in the data word.
The only way to change a “0” to a “1” is by ultraviolet light erasure.
The code is accessed by applying 12V ±0.5V to address pin A9.
Addresses A1–A8, A10–A16, and all control pins are held at VIL.
Address pin A0 is held at VIL for the manufacturer’s code, and held
at VIH for the device code. The code is read on the eight data pins,
O0 –O7. Proper code access is only guaranteed at 25°C to ±5°C.
7
www.fairchildsemi.com
be checked to make certain full erasure is occurring. Incomplete
erasure will cause symptoms that can be misleading. Program-
mers, components, and even system designs have been errone-
ously suspected when incomplete erasure was the problem.
Functional Description (Continued)
ERASURE CHARACTERISTICS
The erasure characteristics of the device are such that erasure
begins to occur when exposed to light with wavelengths shorter
than approximately 4000 Angstroms (Å). It should be noted that
sunlight and certain types of fluorescent lamps have wavelengths
in the 3000Å–4000Å range.
SYSTEM CONSIDERATION
The power switching characteristics of EPROMs require careful
decoupling of the devices. The supply current, ICC, has three
segments that are of interest to the system designer: the standby
current level, the active current level, and the transient current
peaks that are produced by voltage transitions on input pins. The
magnitude of these transient current peaks is dependent of the
output capacitance loading of the device. The associated VCC
transient voltage peaks can be suppressed by properly selected
decoupling capacitors. It is recommended that at least a 0.1 µF
ceramic capacitor be used on every device between VCC and
GND. This should be a high frequency capacitor of low inherent
inductance. In addition, at least a 4.7 µF bulk electrolytic capacitor
shouldbeusedbetweenVCC andGNDforeacheightdevices.The
bulk capacitor should be located near where the power supply is
connected to the array. The purpose of the bulk capacitor is to
overcome the voltage drop caused by the inductive effects of the
PC board traces.
The recommended erasure procedure for the EPROM is expo-
sure to short wave ultraviolet light which has a wavelength of
2537Å. Theintegrateddose(i.e., UVintensityxexposuretime)for
erasure should be a minimum of 15W-sec/cm2.
The EPROM should be placed within 1 inch of the lamp tubes
during erasure. Some lamps have a filter on their tubes which
should be removed before erasure
Anerasuresystemshouldbecalibratedperiodically. Thedistance
fromlamptodeviceshouldbemaintainedatoneinch.Theerasure
time increases as the square of the distance from the lamp (if
distance is doubled the erasure time increases by factor of 4).
Lamps lose intensity as they age. When a lamp is changed, the
distance has changed, or the lamp has aged, the system should
Mode Selection
The modes of operation of NM27C256 listed in Table 1. A single 5V power supply is required in the read mode. All inputs are TTL levels
except for VPP and A9 for device signature.
TABLE 1. Modes Selection
Pins
CE/PGM
OE
VPP
VCC
Outputs
Mode
Read
VIL
VIL
VIH
VCC
VCC
5.0V
5.0V
DOUT
Output Disable
X
High-Z
(Note 16)
Standby
VIH
VIL
VIH
VIH
X
VCC
5.0V
6.25V
6.25V
6.25V
High-Z
DIN
Programming
Program Verify
Program Inhibit
VIH
VIL
VIH
12.75V
12.75V
12.75V
DOUT
High-Z
Note 16: X can be VIL or VIH
.
TABLE 2. Manufacturer’s Identification Code
Pins
A0
(10)
VIL
A9
(24)
12V
12V
O7
(19)
1
O6
(18)
0
O5
(17)
0
O4
(16)
0
O3
(15)
1
O2
O1
(12)
1
O0
Hex
Data
8F
(13)
(11)
Manufacturer Code
Device Code
1
1
1
0
VIH
0
0
0
0
0
0
04
8
www.fairchildsemi.com
Physical Dimensions inches (millimeters) unless otherwise noted
1.450
[36.83]
MAX
28
15
R 0.025
[0.64]
0.520 ± 0.006
[13.21 ±0.15]
0.600
[15.24]
MAX
Glass
1
14
0.280 ±0.010
[7.11 ±0.25]
UV WINDOW
R 0.030-0.055
[0.76 - 1.40]
TYP
0.050-0.060
TYP
0.590-0.620
[14.99 - 15.75]
Glass
Sealant
0.005 MIN
TYP
0.175
MAX
0.225 MAX TYP
0.125 MIN
TYP
95° ±5°
TYP
0.015 -0.060
TYP
0.010 ±0.002
[0.25 ±0.05]
TYP
86°-94°
0.150 MIN
TYP
TYP
0.090-0.110
TYP
0.015-0.021
TYP
0.060-0.100
TYP
+0.025
0.685
-0.060
+0.64
-1.52
17.40
UV Window Cavity Dual-In-Line CerDIP Package (Q)
Order Number NM27C256QXXX
Package Number J28AQ
2827 26 25 24 23 22 21 20 19 18 17 16 15
0.030
(0.762)
Max
0.600 - 0.620
0.062
(1.575)
RAD
0.510 ±0.005
(15.24 - 15.75)
(12.95 ±0.127)
95° ±5°
0.008-0.015
(0.229-0.381)
Pin #1
IDENT
1
2
3
4
5
6
7
8 9 10 11 12 13 14
0.580
(14.73)
1.393 - 1.420
(35.38 - 36.07)
+0.025
0.625
-0.015
+0.635
-0.381
0.050
(1.270)
Typ
(
15.88
(
0.053 - 0.069
0.125-0.165
(3.175-4.191)
(1.346 - 1.753)
0.20
(0.508)
Min
88° 94°
Typ
0.125-0.145
(3.175-3.583)
0.108 ±0.010
(2.540 ±0.254)
0.050 ±0.015
(1.270 ±0.381)
0.018 ±0.003
(0.457 ±0.076)
28-Lead Plastic One-Time-Programmable Dual-In-Line Package
Order Number NM27C256NXXX
Package Number N28B
9
www.fairchildsemi.com
Physical Dimensions inches (millimeters) unless otherwise noted
0.485-0.495
[12.32-12.57]
-H-
Base
Plane
0.106-0.112
[2.69-2.84]
B
S
D-E
S
0.007[0.18]
0.449-0.453
[11.40-11.51]
0.023-0.029
[0.58-0.74]
0.015
[0.38]
Min Typ
-A-
0.045
[1.143]
B
S
D-E
S
0.007[0.18]
0.002[0.05]
°
60
B
S
0.000-0.010
[0.00-0.25]
Polished Optional
0.490-0530
[12.45-13.46]
0.400
[10.16]
-D-
(
)
1
30
4
0.541-0.545
[13.74-13-84]
S
C
D-E, F-G
S
0.015[0.38]
5
29
0.549-0.553
[13.94-14.05]
-G-
-B-
0.585-0.595
[14.86-15.11]
0.013-0.021
[0.33-0.53]
TYP
-F-
See detail A
-J-
C
D-E, F-G
S
0.007[0.18]
M
13
21
0.078-0.095
[1.98-2.41]
0.123-0.140
[3.12-3.56]
0.050
14
A
20
-E-
-C-
0.004[0.10]
0.002[0.05]
0.007[0.18]
S
0.005
[0.13]
Max
0.0100
[0.254]
A
F-G
S
S
0.020
[0.51]
A
F-G
S
0.007[0.18]
S
0.118-0.129
[3.00-3.28]
0.045
[1.14]
0.030-0.040
[0.76-1.02]
B
A
D-E, F-G
0.025
[0.64]
0.010[0.25]
L
S
R
Detail A
Typical
Rotated 90°
Min
B
0.042-0.048
[1.07-1.22]
45°X
0.025
[0.64]
0.021-0.027
[0.53-0.69]
Min
B
0.065-0.071
[1.65-1.80]
0.053-0.059
[1.65-1.80]
0.031-0.037
[0.79-0.94]
0.006-0.012
[0.15-0.30]
0.027-0.033
[0.69-0.84]
0.026-0.032
[0.66-0.81]
0.019-0.025
[0.48-0.64]
Typ
S
Section B-B
Typical
H
D-E, F-G
S
0.007[0.18]
32-Lead Plastic Leaded Chip Carrier (PLCC)
Order Number NM27C256VXXX
Package Number VA32A
10
www.fairchildsemi.com
Life Support Policy
Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written
approval of the President of Fairchild Semiconductor Corporation. As used herein:
1. Life support devices or systems are devices or systems which,
(a)areintendedforsurgicalimplantintothebody,or(b)support
or sustain life, and whose failure to perform, when properly
used in accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a significant
injury to the user.
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably ex-
pected to cause the failure of the life support device or system,
or to affect its safety or effectiveness.
Fairchild Semiconductor
Americas
Fairchild Semiconductor
Europe
Fairchild Semiconductor
Hong Kong
Fairchild Semiconductor
Japan Ltd.
Customer Response Center
Tel. 1-888-522-5372
Fax:
Tel:
Tel:
Tel:
Tel:
+44 (0) 1793-856858
8/F, Room 808, Empire Centre
68 Mody Road, Tsimshatsui East
Kowloon. Hong Kong
Tel; +852-2722-8338
Fax: +852-2722-8383
4F, Natsume Bldg.
Deutsch
English
Français
Italiano
+49 (0) 8141-6102-0
+44 (0) 1793-856856
+33 (0) 1-6930-3696
+39 (0) 2-249111-1
2-18-6, Yushima, Bunkyo-ku
Tokyo, 113-0034 Japan
Tel: 81-3-3818-8840
Fax: 81-3-3818-8841
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
11
www.fairchildsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明