NM93C56ALN [FAIRCHILD]
Microwire Serial EEPROM ; Microwire串行EEPROM\n型号: | NM93C56ALN |
厂家: | FAIRCHILD SEMICONDUCTOR |
描述: | Microwire Serial EEPROM
|
文件: | 总13页 (文件大小:113K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
March 2000
NM93C56A
2K-Bit Serial CMOS EEPROM
(MICROWIRE™ Synchronous Bus)
General Description
Features
NM93C56A is a 2048-bit CMOS non-volatile EEPROM organized
as 128 x 16-bit array. This device features MICROWIRE interface
which is a 4-wire serial bus with chipselect (CS), clock (SK), data
input (DI) and data output (DO) signals. This interface is compat-
ible to many of standard Microcontrollers and Microprocessors.
This device offers a pin (ORG), using which, the user can select
the format of the data (16-bit or 8-bit). If ORG is tied to GND, then
8-bit format is selected, while if ORG is tied to VCC, then 16-bit
format is selected. There are 7 instructions implemented on the
NM93C56A for various Read, Write, Erase, and Write Enable/
Disable operations. This device is fabricated using Fairchild
Semiconductor floating-gate CMOS process for high reliability,
high endurance and low power consumption.
I Wide VCC 2.7V - 5.5V
I User selectable organization
x16 (ORG = 1)
x8 (ORG = 0)
I Typical active current of 200µA
10µA standby current typical
1µA standby current typical (L)
0.1µA standby current typical (LZ)
I No Erase instruction required before Write instruction
I Self timed write cycle
I Device status during programming cycles
I 40 year data retention
“LZ” and “L” versions of NM93C56A offer very low standby current
making them suitable for low power applications. This device is
offered in both SO and TSSOP packages for small space consid-
erations.
I Endurance: 1,000,000 data changes
I Packages available: 8-pin SO, 8-pin DIP, 8-pin TSSOP
Functional Diagram
VCC
CS
SK
INSTRUCTION
DECODER
CONTROL LOGIC
AND CLOCK
GENERATORS
INSTRUCTION
REGISTER
DI
HIGH VOLTAGE
GENERATOR
AND
PROGRAM
TIMER
ADDRESS
REGISTER
ORG
DECODER
EEPROM ARRAY
16
READ/WRITE AMPS
16
VSS
DATA IN/OUT REGISTER
16/8 BITS
DO
DATA OUT BUFFER
1
© 2000 Fairchild Semiconductor International
NM93C56A Rev. F.1
www.fairchildsemi.com
Connection Diagram
Dual-In-Line Package (N)
8–Pin SO (M8) and 8–Pin TSSOP (MT8)
1
2
3
4
8
7
6
5
CS
SK
DI
VCC
NC
ORG
GND
DO
Top View
Package Number
N08E, M08A and MTC08
Pin Names
CS
SK
Chip Select
Serial Data Clock
Serial Data Input
Serial Data Output
Ground
DI
DO
GND
ORG
NC
Organization
No Connect
VCC
Power Supply
NOTE: Pins designated as "NC" are typically unbonded pins. However some of them are bonded for special testing purposes. Hence if a signal is applied to these pins, care
should be taken that the voltage applied on these pins does not exceed the VCC applied to the device. This will ensure proper operation.
Ordering Information
NM 93
C
XX
A
LZ
E
XXX
Letter
Description
Package
N
8-pin DIP
M8
MT8
8-pin SO
8-pin TSSOP
Temp. Range
None
0 to 70°C
V
E
-40 to +125°C
-40 to +85°C
Voltage Operating Range
Blank
L
4.5V to 5.5V
2.7V to 5.5V
LZ
2.7V to 5.5V and
<1µA Standby Current
A
x8 or x16 configuration
2048 bits
Density
56
C
CMOS
CS
Data protect and sequential
read
Interface
93
MICROWIRE
Fairchild Memory Prefix
2
www.fairchildsemi.com
NM93C56A Rev. F.1
Absolute Maximum Ratings (Note 1)
Operating Conditions
Ambient Storage Temperature
-65°C to +150°C
Ambient Operating Temperature
NM93C56A
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
All Input or Output Voltages
with Respect to Ground
+6.5V to -0.3V
NM93C56AE
NM93C56AV
Lead Temperature
(Soldering, 10 sec.)
+300°C
Power Supply (VCC
)
4.5V to 5.5V
ESD rating
2000V
DC and AC Electrical Characteristics VCC = 4.5V to 5.5V unless otherwise specified
Symbol
Parameter
Conditions
Min
Max
Units
ICCA
Operating Current
CS = VIH, SK=1.0 MHz
1
mA
ICCS
Standby Current
CS = VIL
50
-1
µA
µA
IIL
IOL
Input Leakage
Output Leakage
VIN = 0V to VCC
(Note 2)
IILO
Input Leakage ORG Pin
ORG tied to VCC
ORG tied to VSS (Note 3)
-1
-2.5
1
2.5
µA
V
VIL
VIH
Input Low Voltage
Input High Voltage
-0.1
2
0.8
VCC +1
VOL1
VOH1
Output Low Voltage
Output High Voltage
IOL = 2.1 mA
IOH = -400 µA
0.4
0.2
1
V
2.4
VOL2
VOH2
Output Low Voltage
Output High Voltage
IOL = 10 µA
IOH = -10 µA
V
VCC - 0.2
fSK
SK Clock Frequency
SK High Time
(Note 4)
MHz
ns
tSKH
0°C to +70°C
-40°C to +125°C
250
300
tSKL
tSKS
tCS
SK Low Time
250
50
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
SK Setup Time
Minimum CS Low Time
CS Setup Time
DO Hold Time
DI Setup Time
CS Hold Time
(Note 5)
250
100
70
tCSS
tDH
tDIS
tCSH
tDIH
tPD
100
0
DI Hold Time
20
Output Delay
500
500
100
10
tSV
CS to Status Valid
CS to DO in Hi-Z
Write Cycle Time
tDF
CS = VIL
tWP
3
www.fairchildsemi.com
NM93C56A Rev. F.1
Absolute Maximum Ratings (Note 1)
Operating Conditions
Ambient Storage Temperature
-65°C to +150°C
Ambient Operating Temperature
NM93C56AL/LZ
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
All Input or Output Voltages
with Respect to Ground
+6.5V to -0.3V
NM93C56ALE/LZE
NM93C56ALV/LZV
Lead Temperature
(Soldering, 10 sec.)
+300°C
Power Supply (VCC
)
2.7V to 5.5V
ESD rating
2000V
DC and AC Electrical Characteristics VCC = 2.7V to 5.5V unless otherwise specified
Symbol
ICCA
Parameter
Conditions
CS = VIH, SK=1.0 MHz
CS = VIL
Min
Max
Units
Operating Current
1
mA
ICCS
Standby Current
L
LZ (2.7V to 4.5V)
10
1
µA
µA
IIL
IOL
Input Leakage
Output Leakage
VIN = 0V to VCC
(Note 2)
1
µA
IILO
Input Leakage ORG Pin
ORG tied to VCC
-1
1
µA
ORG tied to VSS (Note 3)
-2.5
2.5
VIL
VIH
Input Low Voltage
Input High Voltage
-0.1
0.8VCC
0.15VCC
VCC +1
V
V
VOL
VOH
Output Low Voltage
Output High Voltage
IOL = 10µA
IOH = -10µA
0.1VCC
0.9VCC
fSK
SK Clock Frequency
SK High Time
(Note 4)
0
1
250
KHz
µs
µs
tSKH
tSKL
tSKS
SK Low Time
1
SK Setup Time
0.2
µs
tCS
Minimum CS Low Time
(Note 5)
1
µs
tCSS
tDH
CS Setup Time
DO Hold Time
DI Setup Time
0.2
70
µs
ns
µs
tDIS
0.4
tCSH
tDIH
tPD
CS Hold Time
DI Hold Time
Output Delay
0
ns
µs
µs
0.4
2
1
tSV
CS to Status Valid
µs
tDF
CS to DO in Hi-Z
Write Cycle Time
CS = VIL
0.4
15
µs
ms
tWP
Note 1: Stressabovethoselistedunder“AbsoluteMaximumRatings”maycausepermanentdamage
to the device. This is a stress rating only and functional operation of the device at these or any other
conditionsabovethoseindicatedintheoperationalsectionsofthespecificationisnotimplied. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability.
Capacitance TA = 25°C, f = 1 MHz (Note 6)
Note 2: Typical leakage values are in the 20nA range.
Symbol
COUT
Test
Typ Max Units
Note 3: ORG pin may draw >1µA when in x8 mode due to the internal pull-up transistor.
Output Capacitance
Input Capacitance
5
5
pF
pF
Note 4: TheshortestallowableSKclockperiod=1/fSK (asshownunderthefSK parameter). Maximum
SK clock speed (minimum SK period) is determined by the interaction of several AC parameters stated
in the datasheet. Within this SK period, both tSKH and tSKL limits must be observed. Therefore, it is not
allowable to set 1/fSK = tSKHminimum + tSKLminimum for shorter SK cycle time operation.
CIN
Note 5: CS (Chip Select) must be brought low (to VIL) for an interval of tCS in order to reset all internal
device registers (device reset) prior to beginning another opcode cycle. (This is shown in the opcode
diagram on the following page.)
Note 6: This parameter is periodically sampled and not 100% tested.
AC Test Conditions
VCC Range
VIL/VIH
Input Levels
0.3V/1.8V
VIL/VIH
VOL/VOH
Timing Level
0.8V/1.5V
IOL/IOH
Timing Level
2.7V ≤ VCC ≤ 5.5V
1.0V
10µA
(Extended Voltage Levels)
4.5V ≤ VCC ≤ 5.5V
0.4V/2.4V
1.0V/2.0V
0.4V/2.4V
2.1mA/-0.4mA
(TTL Levels)
Output Load: 1 TTL Gate (CL = 100 pF)
4
www.fairchildsemi.com
NM93C56A Rev. F.1
Refer Table 1 and Table 2 for more details. This pin is internally
pulled-up to VCC. Hence leaving this pin unconnected would
default to 16-bit data format.
Pin Description
Chip Select (CS)
ThisisanactivehighinputpintoNM93C56AEEPROM(thedevice)
and is generated by a master that is controlling the device. A high
level on this pin selects the device and a low level deselects the
device. All serial communications with the device is enabled only
when this pin is held high. However this pin cannot be permanently
tied high, as a rising edge on this signal is required to reset the
internal state-machine to accept a new cycle and a falling edge to
initiateaninternalprogrammingafterawritecycle.Allactivityonthe
SK, DI and DO pins are ignored while CS is held low.
Microwire Interface
AtypicalcommunicationontheMicrowirebusismadethroughthe
CS, SK, DI and DO signals. To facilitate various operations on the
Memory array, a set of 7 instructions are implemented on
NM93C56A. The format of each instruction is listed under Table
1 (for 16-bit format) and Table 2 (for 8-bit format).
Instruction
Each of the above 7 instructions is explained under individual
instruction descriptions.
Serial Clock (SK)
Thisisaninputpintothedeviceandisgeneratedbythemasterthat
is controlling the device. This is a clock signal that synchronizes the
communicationbetweenamasterandthedevice. Allinputinforma-
tion(DI)tothedeviceislatchedontherisingedgeofthisclockinput,
whileoutputdata(DO)fromthedeviceisdrivenfromtherisingedge
of this clock input. This pin is gated by CS signal.
Start bit
This is a 1-bit field and is the first bit that is clocked into the device
whenaMicrowirecyclestarts.Thisbithastobe“1”foravalidcycle
to begin. Any number of preceding “0” can be clocked into the
device before clocking a “1”.
Serial Input (DI)
Opcode
This is an input pin to the device and is generated by the master
that is controlling the device. The master transfers Input informa-
tion (Start bit, Opcode bits, Array addresses and Data) serially via
this pin into the device. This Input information is latched on the
rising edge of the SCK. This pin is gated by CS signal.
This is a 2-bit field and should immediately follow the start bit.
These two bits (along with 2 MSB of address field) select a
particular instruction to be executed.
Address Field
Serial Output (DO)
Depending on the selected organization, this is a 8-bit or 9-bit field
and should immediately follow the Opcode bits. In NM93C56A,
only the LSB 7 bits (or 8 bits) are used for address decoding during
READ, WRITE and ERASE instructions. During all other instruc-
tions, the MSB 2 bits are used to decode instruction (along with
Opcode bits).
This is an output pin from the device and is used to transfer Output
data via this pin to the controlling master. Output data is serially
shifted out on this pin from the rising edge of the SCK. This pin is
active only when the device is selected.
Organization (ORG)
Data Field
This is an input pin to the device and is used to select the format
of data (16-bit or 8-bit). If this pin is tied high, 16-bit format is
selected, while if it is tied low, 8-bit format is selected. Depending
on the format selected, NM93C56A requires 7-bit address field
(for 16-bit data format) or 8-bit address field (for 8-bit data format).
Depending on the selected organization, this is a 16-bit or 8-bit
field and should immediately follow the Address bits. Only the
WRITE and WRALL instructions require this field. MSB bit (D15 or
D7) is clocked first and LSB bit (D0) is clocked last (both during
writes as well as reads).
Table 1. Instruction set (16-bit organization)
Instruction
READ
Start Bit
Opcode Field
Address Field
Data Field
1
1
1
1
1
1
1
10
00
01
00
00
11
00
X
1
X
0
0
X
1
A6 A5 A4 A3 A2 A1 A0
WEN
1
X
X
X
X
X
X
WRITE
WRALL
WDS
A6 A5 A4 A3 A2 A1 A0
D15-D0
D15-D0
1
0
X
X
X
X
X
X
X
X
X
X
X
X
ERASE
ERAL
A6 A5 A4 A3 A2 A1 A0
0
X
X
X
X
X
X
5
www.fairchildsemi.com
NM93C56A Rev. F.1
Table 2. Instruction set (8-bit organization)
Instruction
READ
Start Bit
Opcode Field
Address Field
Data Field
1
1
1
1
1
1
1
10
00
01
00
00
11
00
X
1
X
0
0
X
1
A7 A6 A5 A4 A3 A2 A1 A0
WEN
1
X
X
X
X
X
X
X
WRITE
WRALL
WDS
A7 A6 A5 A4 A3 A2 A1 A0
D7-D0
D7-D0
1
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ERASE
ERAL
A7 A6 A5 A4 A3 A2 A1 A0
0
X
X
X
X
X
X
X
3) Write (WRITE)
Functional Description
WRITE instruction allows write operation to a specified location in
thememorywithaspecifieddata. Thisinstructionisvalidonlywhen
A typical Microwire cycle starts by first selecting the device
(bringing the CS signal high). Once the device is selected, a valid
Start bit (“1”) should be issued to properly recognize the cycle.
Following this, the 2-bit opcode of appropriate instruction should
be issued. After the opcode bits, the 8-bit (or 9-bit) address
informationshouldbeissued. Forcertaininstructions,someofthe
bits of this field are don’t care values (can be “0” or “1”), but they
shouldstillbeissued. Followingtheaddressinformation, depend-
ing on the instruction (WRITE and WRALL), 16-Bit data (or 8-Bit)
is issued. Otherwise, depending on the instruction (READ), the
device starts to drive the output data on the DO line. Other
instructions perform certain control functions and do not deal with
data bits. The Microwire cycle ends when the CS signal is brought
low. However during certain instructions, falling edge of the CS
signal initiates an internal cycle (Programming), and the device
remains busy till the completion of the internal cycle. Each of the
7 instructions is explained in detail in the following sections.
I Device is write-enabled (Refer WEN instruction)
Input information (Start bit, Opcode, Address and Data) for this
WRITE instruction should be issued as listed under Table 1 or
Table 2. After inputting the last bit of data (D0 bit), CS signal must
be brought low before the next rising edge of the SK clock. This
falling edge of the CS initiates the self-timed programming cycle.
It takes tWP time (Refer appropriate DC and AC Electrical Charac-
teristics table) for the internal programming cycle to finish. During
this time, the device remains busy and is not ready for another
instruction.
The status of the internal programming cycle can be polled at any
time by bringing the CS signal high again, after tCS interval. When
CS signal is high, the DO pin indicates the READY/BUSY status
of the chip. DO = logical 0 indicates that the programming is still
in progress. DO = logical 1 indicates that the programming is
finished and the device is ready for another instruction. It is not
required to provide the SK clock during this status polling. While
the device is busy, it is recommended that no new instruction be
issued. Refer Write cycle diagram.
1) Read (READ)
READ instruction allows data to be read from a selected location
in the memory array. Input information (Start bit, Opcode and
Address)forthisinstructionshouldbeissuedaslistedunderTable
1 or Table 2. Upon receiving a valid input information, decoding of
the opcode and the address is made, followed by data transfer
from the selected memory location into a 16-bit serial-out shift
register. This 16-bit data (or 8-bit data) is then shifted out on the
DO pin. MSB of the data (D15 or D8) is shifted out first and LSB
(DO) is shifted out last. A dummy-bit (logical 0) precedes this data
output string. Output data changes are initiated on the rising edge
of the SK clock. After reading the 16-bit (or 8-bit) data, the CS
signalcanbebroughtlowtoendtheReadcycle. Refer Readcycle
diagram.
It is also recommended to follow this instruction (after the device
becomes READY) with a Write Disable (WDS) instruction to
safeguarddataagainstcorruptionduetospuriousnoise,inadvert-
ent writes etc.
4) Write All (WRALL)
Write all (WRALL) instruction is similar to the Write instruction
except that WRALL instruction will simultaneously program all
memorylocationswiththedatapatternspecifiedintheinstruction.
This instruction is valid only when
2) Write Enable (WEN)
I Device is write-enabled (Refer WEN instruction)
When VCC is applied to the part, it “powers up” in the Write Disable
(WDS) state. Therefore, all programming operations must be
preceded by a Write Enable (WEN) instruction. Once a Write
Enable instruction is executed, programming remains enabled
until a Write Disable (WDS) instruction is executed or VCC is
completely removed from the part. Input information (Start bit,
Opcode and Address) for this WEN instruction should be issued
as listed under Table 1 or Table 2. The device becomes write-
enabled at the end of this cycle when the CS signal is brought low.
Execution of a READ instruction is independent of WEN instruc-
tion. Refer Write Enable cycle diagram.
Input information (Start bit, Opcode, Address and Data) for this
WRALL instruction should be issued as listed under Table 1 or
Table 2. After inputting the last bit of data (D0 bit), CS signal must
be brought low before the next rising edge of the SK clock. This
falling edge of the CS initiates the self-timed programming cycle.
It takes tWP time (Refer appropriate DC and AC Electrical Charac-
teristics table) for the internal programming cycle to finish. During
this time, the device remains busy and is not ready for another
instruction. Status of the internal programming can be polled as
described under WRITE instruction description. While the device
is busy, it is recommended that no new instruction be issued.
Refer Write All cycle diagram.
6
www.fairchildsemi.com
NM93C56A Rev. F.1
2. After inputting the last bit of data (A0 bit), CS signal must be
broughtlowbeforethenextrisingedgeoftheSKclock. Thisfalling
edge of the CS initiates the self-timed programming cycle. It takes
tWP time (Refer appropriate DC and AC Electrical Characteristics
table)fortheinternalprogrammingcycletofinish.Duringthistime,
the device remains busy and is not ready for another instruction.
Status of the internal programming can be polled as described
under WRITE instruction description. While the device is busy, it
is recommended that no new instruction be issued. Refer Erase
All cycle diagram.
5) Write Disable (WDS)
Write Disable (WDS) instruction disables all programming opera-
tions and should follow all programming operations. Executing
this instruction after a valid write instruction would protect against
accidental data disturb due to spurious noise, glitches, inadvert-
ent writes etc. Input information (Start bit, Opcode and Address)
for this WDS instruction should be issued as listed under Table 1
or Table 2. The device becomes write-disabled at the end of this
cycle when the CS signal is brought low. Execution of a READ
instructionisindependentofWDSinstruction. ReferWriteDisable
cycle diagram.
Note: The Fairchild CMOS EEPROMs do not require an “ERASE” or “ERASE ALL”
instruction prior to the “WRITE” or “WRITE ALL” instruction, respectively. The
“ERASE” and “ERASE ALL” instructions are included to maintain compatibility with
earlier technology EEPROMs.
6) Erase (ERASE)
The ERASE instruction will program all bits in the specified
location to logical “1” state. Input information (Start bit, Opcode
and Address) for this WDS instruction should be issued as listed
under Table 1 or Table 2. After inputting the last bit of data (A0 bit),
CS signal must be brought low before the next rising edge of the
SK clock. This falling edge of the CS initiates the self-timed
programming cycle. It takes tWP time (Refer appropriate DC and
AC Electrical Characteristics table) for the internal programming
cycle to finish. During this time, the device remains busy and is not
ready for another instruction. Status of the internal programming
can be polled as described under WRITE instruction description.
While the device is busy, it is recommended that no new instruc-
tion be issued. Refer Erase cycle diagram.
Clearing of Ready/Busy status
When programming is in progress, the Data-Out pin will display
the programming status as either BUSY (low) or READY (high)
when CS is brought high (DO output will be tri-stated when CS is
low). To restate, during programming, the CS pin may be brought
high and low any number of times to view the programming status
without affecting the programming operation. Once programming
is completed (Output in READY state), the output is ‘cleared’
(returned to normal tri-state condition) by clocking in a Start Bit.
After the Start Bit is clocked in, the output will return to a tri-stated
condition. When clocked in, this Start Bit can be the first bit in a
command string, or CS can be brought low again to reset all
internal circuits. Refer Clearing Ready Status diagram.
7) Erase All (ERAL)
Related Document
The Erase all instruction will program all locations to logical “1”
state. Input information (Start bit, Opcode and Address) for this
WDS instruction should be issued as listed under Table 1 or Table
Application Note: AN758 - Using Fairchild’s MICROWIRE™ EE-
PROM.
7
www.fairchildsemi.com
NM93C56A Rev. F.1
Timing Diagrams
SYNCHRONOUS DATA TIMING
CS
SK
DI
t
t
t
t
t
CSH
SKS
CSS
SKH
SKL
t
t
DIH
DIS
Valid
Input
Valid
Input
t
PD
t
t
DF
DF
t
t
PD
DH
Valid
Valid
Output
Output
DO (Data Read)
t
SV
Valid Status
DO (Status Read)
READ CYCLE (READ)
t
CS
CS
SK
A
A
n-1
1
1
0
A1
A0
n
DI
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
High - Z
0
D
D1
D0
DO
n
Dummy
Bit
93C56A (ORG=1;
Address bits pattern -> x-A6-A5-A4-A3-A2-A1-A0
(x -> Don't Care, can be 0 or 1; A6-to-A0 -> User defined)
=A8; D =D7):
A =A7; D =D15):
n n
93C56A (ORG=0;
A
n
n
Address bits pattern -> x-A7-A6-A5-A4-A3-A2-A1-A0; User defined
(x -> Don't Care, can be 0 or 1; A7-to-A0 -> User defined)
ERASE/WRITE ENABLE CYCLE (EWEN)
t
CS
CS
SK
DI
1
0
0
A
A
A1
A0
n
n-1
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
High - Z
DO
93C56A (ORG=1;
Address bits pattern -> 1-1-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
93C56A (ORG=0;
A =A7):
n
A
=A8):
n
Address bits pattern -> 1-1-x-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
8
www.fairchildsemi.com
NM93C56A Rev. F.1
Timing Diagrams (Continued)
ERASE/WRITE DISABLE CYCLE (EWDS)
t
CS
CS
SK
DI
A
A
n-1
1
0
0
A1
A0
n
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
High - Z
DO
93C56A (ORG=1;
Address bits pattern -> 0-0-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
93C56A (ORG=0;
A =A7):
n
A
=A8):
n
Address bits pattern -> 0-0-x-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
WRITE CYCLE (WRITE)
tCS
CS
SK
1
0
1
A
A
A1
A0
D
D
D1
D0
n
n-1
n
n-1
Data
DI
tWP
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
Bits(16/8)
High - Z
Ready
DO
Busy
93C56A (ORG=1;
A =A7; D =D15):
n n
Address bits pattern -> x-A6-A5-A4-A3-A2-A1-A0
(x -> Don't Care, can be 0 or 1; A6-to-A0 -> User defined)
-> D15-to-D0; User defined
Data bits pattern
93C56A (ORG=0; =A8; D =D7):
Address bits pattern -> x-A7-A6-A5-A4-A3-A2-A1-A0
(x -> Don't Care, can be 0 or 1; A7-to-A0 -> User defined)
-> D7-to-D0; User defined
A
n
n
Data bits pattern
WRITE ALL CYCLE (WRALL)
tCS
CS
SK
1
0
0
A
A
A1
A0
D
D
D1
D0
n
n-1
n
n-1
Data
DI
tWP
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
Bits(16/8)
High - Z
Ready
DO
Busy
93C56A (ORG=1;
A =A7; D =D15):
n n
Address bits pattern -> 0-1-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
Data bits pattern -> D15-to-D0; User defined
93C56A (ORG=0; =A8; D =D7):
Address bits pattern -> 0-1-x-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
A
n
n
Data bits pattern
-> D7-to-D0; User defined
9
www.fairchildsemi.com
NM93C56A Rev. F.1
Timing Diagrams (Continued)
ERASE CYCLE (ERASE)
tCS
CS
SK
DI
1
1
1
A
A
A1
A0
n
n-1
tWP
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
High - Z
Ready
DO
Busy
93C56A (ORG=1;
A =A7):
n
Address bits pattern -> x-A6-A5-A4-A3-A2-A1-A0
(x -> Don't Care, can be 0 or 1; A6-to-A0 -> User defined)
93C56A (ORG=0;
A =A8):
n
Address bits pattern -> x-A7-A6-A5-A4-A3-A2-A1-A0; User defined
(x -> Don't Care, can be 0 or 1; A7-to-A0 -> User defined)
ERASE ALL CYCLE (ERAL)
t
CS
CS
SK
DI
A
A
n-1
1
1
1
A1
A0
n
t
WP
Start Opcode
Bit Bits(2)
Address
Bits(8/9)
High - Z
Ready
DO
Busy
93C56A (ORG=1;
A =A7):
n
Address bits pattern -> 1-0-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
93C56A (ORG=0;
A
=A8):
n
Address bits pattern -> 1-0-x-x-x-x-x-x-x; (x -> Don't Care, can be 0 or 1)
CLEARING READY STATUS
CS
SK
DI
Start
Bit
High - Z
High - Z
Ready
DO
Busy
Note: This Start bit can also be part of a next instruction. Hence the cycle
can be continued(instead of getting terminated, as shown) as if a new
instruction is being issued.
10
www.fairchildsemi.com
NM93C56A Rev. F.1
Physical Dimensions inches (millimeters) unless otherwise noted
0.189 - 0.197
(4.800 - 5.004)
8
7
6
3
5
4
0.228 - 0.244
(5.791 - 6.198)
1
2
Lead #1
IDENT
0.150 - 0.157
(3.810 - 3.988)
0.053 - 0.069
(1.346 - 1.753)
0.010 - 0.020
(0.254 - 0.508)
0.004 - 0.010
(0.102 - 0.254)
x 45°
8° Max, Typ.
All leads
Seating
Plane
0.04
0.0075 - 0.0098
(0.190 - 0.249)
Typ. All Leads
(0.102)
All lead tips
0.014
(0.356)
0.016 - 0.050
(0.406 - 1.270)
Typ. All Leads
0.050
(1.270)
Typ
0.014 - 0.020
(0.356 - 0.508)
Typ.
Molded Package, Small Outline, 0.15 Wide, 8-Lead (M8)
Package Number M08A
11
www.fairchildsemi.com
NM93C56A Rev. F.1
Physical Dimensions inches (millimeters) unless otherwise noted
0.114 - 0.122
(2.90 - 3.10)
8
5
(7.72) Typ
(4.16) Typ
0.169 - 0.177
(4.30 - 4.50)
0.246 - 0.256
(6.25 - 6.5)
(1.78) Typ
(0.42) Typ
0.123 - 0.128
(3.13 - 3.30)
(0.65) Typ
Land pattern recommendation
1
4
Pin #1 IDENT
0.0433
Max
(1.1)
0.0035 - 0.0079
See detail A
0.002 - 0.006
(0.05 - 0.15)
0.0256 (0.65)
Typ.
Gage
plane
0.0075 - 0.0098
(0.19 - 0.30)
0°-8°
DETAIL A
Typ. Scale: 40X
0.0075 - 0.0098
(0.19 - 0.25)
0.020 - 0.028
(0.50 - 0.70)
Seating
plane
Notes: Unless otherwise specified
1. Reference JEDEC registration MO153. Variation AA. Dated 7/93
8-Pin Molded TSSOP, JEDEC (MT8)
Package Number MTC08
12
www.fairchildsemi.com
NM93C56A Rev. F.1
Physical Dimensions inches (millimeters) unless otherwise noted
0.373 - 0.400
(9.474 - 10.16)
0.090
(2.286)
8
7
0.032 0.005
(0.813 0.127)
RAD
8
7
6
5
4
0.092
(2.337)
DIA
0.250 - 0.005
(6.35 0.127)
Pin #1
IDENT
+
Pin #1 IDENT
1
Option 1
1
2
3
Option 2
0.280
MIN
0.040
(1.016)
Typ.
(7.112)
0.030
0.145 - 0.200
(3.683 - 5.080)
0.039
(0.991)
MAX
(0.762)
0.300 - 0.320
(7.62 - 8.128)
20° 1°
0.130 0.005
(3.302 0.127)
0.125 - 0.140
95° 5°
(3.175 - 3.556)
0.065
(1.651)
0.125
(3.175)
DIA
0.020
90° 4°
Typ
0.009 - 0.015
(0.229 - 0.381)
(0.508)
Min
0.018 0.003
(0.457 0.076)
NOM
+0.040
-0.015
0.325
0.100 0.010
+1.016
-0.381
8.255
(2.540 0.254)
0.045 0.015
(1.143 0.381)
0.060
(1.524)
0.050
(1.270)
Molded Dual-In-Line Package (N)
Package Number N08E
Life Support Policy
Fairchild's products are not authorized for use as critical components in life support devices or systems without the express written
approval of the President of Fairchild Semiconductor Corporation. As used herein:
1. Life support devices or systems are devices or systems which,
(a)areintendedforsurgicalimplantintothebody,or(b)support
or sustain life, and whose failure to perform, when properly
used in accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a significant
injury to the user.
2. A critical component is any component of a life support device
or system whose failure to perform can be reasonably ex-
pected to cause the failure of the life support device or system,
or to affect its safety or effectiveness.
Fairchild Semiconductor
Americas
Fairchild Semiconductor
Europe
Fairchild Semiconductor
Hong Kong
Fairchild Semiconductor
Japan Ltd.
Customer Response Center
Tel. 1-888-522-5372
Fax:
Tel:
Tel:
Tel:
Tel:
+44 (0) 1793-856858
8/F, Room 808, Empire Centre
68 Mody Road, Tsimshatsui East
Kowloon. Hong Kong
Tel; +852-2722-8338
Fax: +852-2722-8383
4F, Natsume Bldg.
Deutsch
English
Français
Italiano
+49 (0) 8141-6102-0
+44 (0) 1793-856856
+33 (0) 1-6930-3696
+39 (0) 2-249111-1
2-18-6, Yushima, Bunkyo-ku
Tokyo, 113-0034 Japan
Tel: 81-3-3818-8840
Fax: 81-3-3818-8841
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.
13
www.fairchildsemi.com
NM93C56A Rev. F.1
相关型号:
©2020 ICPDF网 联系我们和版权申明