GS-12-0977 [FCI-CONNECTOR]
Conan Micro miniature Connector System; 柯南微小型连接器系统
| 型号： | GS-12-0977 |
| 厂家： | 
FCI CONNECTOR |
| 描述： | Conan Micro miniature Connector System |
| 文件： | 总17页 (文件大小：174K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
1 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
1.0
OBJECTIVE
This specification defines the performance, test, quality, and reliability requirements of the Conan Micro
miniature Connector System as well as Lead Free product that meets the requirement of the European
Union Directives of Restriction for Hazardous Substances (Directive 2002/95/EC).
2.0
SCOPE
This specification is applicable to the termination characteristics of the Conan connector system, which provides
for parallel interconnection of printed wiring boards in low power applications.
3.0
GENERAL
PARAGRAPH
TITLE
1.0
2.0
3.0
4.0
5.0
5.1
5.2
5.3
5.4
6.0
7.0
8.0
9.0
9.1
9.2
9.3
9.4
9.5
Objective
Scope
General
Applicable Documents
Requirements
Qualification
Material
Finish
Design and Construction
Electrical Characteristics
Mechanical Characteristics
Environmental Conditions
Quality Assurance Provisions
Equipment Calibration
Inspection Conditions
Sample Quantities and Description
Qualification Testing
Requalification Testing
4.0
APPLICABLE DOCUMENTS
In the event of a conflict between the requirements outlined in this specification and the product drawing,
the product drawing shall take precedence. In the event of a conflict between the requirements outlined
in this specification and the referenced documents, this specification shall take precedence.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
2 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
4.1
4.2
SPECIFICATIONS
4.1.1
Engineering Drawing 10118744
MILITARY STANDARDS
4.2.1
4.2.2
4.2.3
MIL-STD-202F: Test Methods for Electronic Component Parts
EIA-364: Test Methods for Electrical Connectors
MIL-C-45662: Equipment Calibration
4.3
FEDERAL SPECIFICATIONS
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
QQ-N-290: Nickel Plating (Electrodeposited)
QQ-N-533: Beryllium Copper Alloy Strip
QQ-B-750: Phosphor Bronze Alloy Strip
QQ-B-613: Cartridge Brass Alloy Strip
QQ-S-571: Solder
4.4
OTHER STANDARDS AND SPECIFICATIONS
4.4.1
4.4.2
4.4.3
4.4.3
4.4.4
4.4.5
UL-94:
ASTM B-19: Brass
ASTM B-36: Brass
ASTMB-194: Beryllium Copper
ASTM B-103: Phosphor Bronze
ISO 9000
Flammability
4.5
FCI SPECIFICATIONS
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
BUS-03-114: Capacitance Measurement
BUS-03-404: Normal Force Measurement
GS-19-037: Solderability
GS-19-036: Porosity
GS-19-039: Plating Adhesion
4.6
FCI LAB REPORTS - SUPPORTING DATA
4.6.1
4.6.6
DL-2011-04-018: Qualification Testing
ZA5-2625 Lead-free plating investigation (DOE pure tin)
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
3 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
5.0
REQUIREMENTS
5.1
QUALIFICATION
Connectors furnished under this specification shall be products that are capable of meeting
the qualification test requirements specified herein.
5.2
MATERIAL
The material for each part shall be as specified herein, or equivalent. Substitute material shall
meet the performance requirements of this specification.
5.2.1
Receptacle Terminal. The base material shall be beryllium copper strip C17200,
SHM (TMO5).
5.2.2
5.2.3
Header Terminal. The base material shall be 3/4 hard phosphor bronze strip C51000.
Header and Receptacle Insulator Housing. The insulators shall be molded of 30%
glass filled liquid crystal polymer that is rated 94V-0 or better in accordance with UL-
94.
5.2.4
Hold-Down. The base material shall be full hard, brass strip C26000. See Section
5.3.2 for plating requirements.
5.3
FINISH
5.3.1
The header and receptacle terminals shall be plated in the contact area with GOLD
OR GXT plating over 50 microinches Nickel or Copper. The terminal soldertail shall
be plated with 100 microinches min. pure tin over 50 microinches min. Nickel or
Copper . The terminal areas outside of the contact area and soldertail areas shall
be plated with 50 microinches min. Nickel or Copper.
5.3.2
The hold-down shall be plated with 100 microinches min. pure tin over 50
microinches min. Nickel or Copper.
5.4
DESIGN AND CONSTRUCTION
The connector shall be a multi-piece assembly having two rows of contacts with surface
mount soldertail terminations and solderable surface mount retention devices for installation
on surface mount printed wiring boards or flexible circuits.
5.4.1
5.4.2
Mating. The connector shall be capable of mating and unmating manually without
the use of special tools.
Workmanship. Connectors shall be uniform in quality and shall be free from burrs,
scratches, cracks, voids, chips, blisters, pin holes, sharp edges, and other defects
that will adversely affect life or serviceability. Open knit lines, which may appear as
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
4 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
a crack, may be present in the housing but do not adversely affect the performance
of the connector as per the requirements outlined in this specification.
6.0 ELECTRICAL CHARACTERISTICS
6.1 CURRENT RATING
The maximum current rating based upon a 30 degree C temperature rise over ambient is 1.0 amp
DC per contact for a 69 position connector with all contacts carrying current. The maximum current
carrying capacity for an individual contact is 2.0 amps D.C.
6.2
LOW LEVEL CONTACT RESISTANCE
The low level contact resistance of the 4.15mm, 4.5mm, 5mm and 5.5mm mated height connectors
shall not exceed 20 milliohms initially and 30 milliohms after environmental exposure when
measured in accordance with EIA-364 TP45. The low level contact resistance of the 6mm, 7mm
and 7.5mm mated height connectors shall not exceed 25 milliohms initially and 35 milliohms after
environmental exposure when measured in accordance with EIA-364 TP45. The following details
shall apply:
A.
Method of connection: Attach current and voltage leads as shown in Figure 1.0. The
resistance shall be measured from the solder tail of the header to the solder tail of the
receptacle.
B
Test Voltage: 20 millivolts DC max open circuit.
Test Current: Not to exceed 100 milliamperes.
INSULATION RESISTANCE
C.
6.3
The insulation resistance of the mated connectors shall not be less than 1 gigaohm after
environmental exposure when measured in accordance with MIL-STD-202F, Method 302.
The following details shall apply:
A.
B.
C.
Test voltage: 500 volts DC
Preparation: The connectors shall be mated but not soldered to a P.C. board.
Measurement points: The insulation resistance shall be measured between a
minimum of 10 adjacent and 10 opposing contacts per connector.
6.4
DIELECTRIC WITHSTANDING VOLTAGE
There shall be no evidence of arc-over, insulation breakdown or leakage current in excess of 1
milliampere when the unmated connector is tested in accordance with MIL-STD-202F, Method
301. The following details shall apply:
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
5 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
A.
Test voltage: 500 volts rms at 60 hz.
B.
C.
D.
Test duration: 60 seconds
Preparation: The connectors shall be mounted but not soldered to a P.C. board.
Measurement points: The dielectric withstanding voltage shall be applied
across a minimum of 10 adjacent and 10 opposing contacts.
6.5
CAPACITANCE
The capacitance between adjacent and opposing contacts in a mated connector shall not exceed
2.0 picofarads when tested in accordance with Du Pont specification BUS-03-114. The
following details shall apply:
A.
B.
C.
Test frequency: 100 khz
Preparation: The connectors shall be mated but not soldered to a P.C. board.
Measurement points: The capacitance shall be measured across a minimum of
10 adjacent and 10 opposing contacts.
7.0
MECHANICAL CHARACTERISTICS
7.1
CONTACT RETENTION
Individual contacts in the unterminated header and receptacle portions of the connector shall
withstand a load normal to the soldertail of 0.25 min. pounds. The force shall be measured on a
minimum of 10 contacts per unmated header and receptacle connector. The crosshead speed
shall be no greater than 0.2 inches per minute.
7.2
7.3
MATING FORCE
The force to mate header and receptacle connectors that are mounted on a P.C. board shall
not exceed 125 grams per contact. The crosshead speed shall be no greater than 1.0 inches
per minute.
UNMATING FORCE
The force to unmate header and receptacle connectors that are mounted on a P.C. board shall
be no less than 25 grams per contact. The crosshead speed shall be no greater than 1.0 inch
per minute.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
6 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
7.4
NORMAL FORCE
The contact normal force shall not be less than 75 grams when tested in accordance with BUS-03-
404 Section 3.2 (probe method). Refer to Figure 2.0. The following process shall be used:
7.4.1
7.4.2
7.4.3
Solder the receptacle and header connectors to a printed circuit board.
Select the receptacle terminal positions to be measured.
Measure the maximum terminal gap between the selected positions and the opposite row
of terminals in the receptacle connector.
7.4.4
7.4.5
7.4.6
Measure the minimum width across the selected positions and the opposite row of
terminals of the header connector.
Using an "L" shaped probe, Lab Fixture Number MF149, Figure 2, deflect the contact
positions on the instron tester.
The minimum beam deflection occurs on the long row of terminals. Calculate the
minimum beam deflection as follows:
V = Minimum width across the header terminals.
W = Maximum gap between receptacle terminals.
Z = Deflection of terminals in the long row.
A = Number of terminals in the short row.
B = Number of terminals in the long row.
A*(V-W)
Minimum deflection (Z) =---------
(A+B
)
7.4.7
Starting at the bottom of the force-deflection curve where the terminal begins to deflect,
move up the curve a distance equal to the minimum deflection, Z, to find the minimum
normal force. Measure a minimum of 5 contacts per connector.
7.5
BOARD RETENTION
The force to remove the header and receptacle connectors from a P.C. board shall be no less than
10 lbs. when both the hold-downs and the terminal leads are soldered in place. The crosshead
speed shall be no greater than 0.2 inches per minute.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
7 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
8.0
ENVIRONMENTAL CONDITIONS
After exposure to the following environmental conditions in accordance with the specified test
procedures and/or details, the product shall show no physical damage and shall meet the electrical
and mechanical requirements per paragraphs 6.0 and 7.0 as specified in the Table 1.0 test
sequences. Unless specified otherwise, the assemblies shall be mated during exposure.
8.1 HUMIDITY, STEADY STATE - MIL-STD-202F, METHOD 103B
A.
B.
C.
D.
Relative humidity: 90% +/- 5%
Temperature: 40 +/- 3 Deg. C
Test Duration: 96 hours
Samples: Groups 1 and 2 - unmated during exposure.
8.2 THERMAL SHOCK - MIL-STD-202F, METHOD 107G
A. Test condition: A - (25, 1 hour cycles).
B. Temperature range: -55 +/- 5 to +130 +5/-0 Deg. C.
C. Time at each temperature: 30 minutes
D. Transfer time: 5 minutes max.
E. Samples: Groups 1 and 2 - unmated during exposure.
8.3
ENVIRONMENTAL SEQUENCE
Phase 1 - Thermal shock, MIL-STD-202F, Method 107G.
A.
B.
C.
D.
Test duration - 36, 1-hour cycles
Temperature range - between -20 and +80 deg. C.
Time at temperature - 30 minutes
Transfer time - 5 minutes, maximum
Phase 2 - Humidity, MIL-STD-202F, Method 103B.
A.
B.
C.
Test duration - 10 days
Relative humidity - 95%
Temperature - 40 +/- 3 deg. C.
8.3.1 - High Tem Life MIL-STD-202F, Method 108A
A.
B.
Test Duration - 21 days
Temperature - 105 deg. C.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
8 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
8.4
SHOCK - MIL-STD-202F, METHOD 213B
A.
Condition - A, (50G, 11 ms half-sine) contacts shall show no evidence of discontinuity
greater than one microsecond. The following details shall apply:
B.
C.
D.
Shocks: 3 shocks in both directions along each of 3 orthogonal axes (18 total).
Mounting: See Figure 3.0.
No discontinuities greater than 1.0 microseconds.
8.5
VIBRATION – IEC60512, TEST 6D
A.
B.
C.
Vibration Amplitude: +/-20G or .06" da.
Frequency range: 10 to 2000 hz.
Sweep time and duration: 20 minutes per sweep, 4 hours along each of 3 orthogonal
axes (12 hours total).
D.
Mounting: See Figure 3.0.
8.6 INDUSTRIAL MIXED FLOWING GAS
A. Class: EIA 364-65 test method, Class IIa
B Duration: 120 hours, mated
8.7
SOLDERABILITY - MIL-STD-202F METHOD 208F
A.
B.
Contact tails shall be solderable over a minimum of .035 from the tip.
Steam aging: Suspended 2 inches above boiling, distilled water for 4
hours. C. Acceptable coverage: 95% minimum.
D.
Solder: 60/40 tin-lead in accordance with QQ-S-571, Type
Flux: Type RMA.
S. E.
F.
Flux immersion time: 10 seconds.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
9 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
G.
Solder dwell time: Terminal held immediately above solder for 10 seconds and then I
mmersed for 5 +/- 0.5 seconds. The solder tails shall be bent normal to the base of
the connector to prevent the insulator from touching the solder bath.
H.
I.
Solder temperature: 245 +/- 5 deg. C.
Samples: Group 7 - unsoldered and unmated.
8.8
8.9
RESISTANCE TO IR SOLDERING HEAT
o
o
A.
B.
Temperature: 260 C + 5 C (peak temperature)
Duration: 30 seconds.
DURABILITY - STANDARD LABORATORY PROCEDURES
A.
B.
Number of cycles:
30 cycles for 8u" GXT Contact Finish
Crosshead speed: 1 inch/minute max.
9.0
QUALITY ASSURANCE PROVISIONS
9.1
EQUIPMENT CALIBRATION
All test equipment and inspection facilities used in the performance of any test shall be maintained
in a calibration system in accordance with MIL-C-45662 and ISO 9000.
9.2
INSPECTION CONDITIONS
Unless otherwise specified herein, all inspections shall be performed under the following
ambient conditions:
A.
B.
C.
Temperature: 25 +/- 5 deg. C.
Relative humidity: 30 to 60%
Barometric pressure: Local ambient.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
10 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
9.3
SAMPLE QUANTITIES
Sample quantities for the respective test groups are as follows:
Test
Group
Size (number of
positions)
Connector
Height
Quantity
1
2
69
69
4.15
4.15
3
3
3
3A
21 & 69
21 & 69
4.15 & 7.0
4.15 & 7.0
3 ea.
3 ea.
4
21
7.0
3
5
5A
69
69
7.0
7.0
3
3
6
69
4.15 & 7.0
7.0
3 ea.
3
7
69
8
9 & 21 & 69
7.0
3 ea.
3
9
69
21 & 69
69
N/A
10
11
11A
11B
12
4.15 & 7.0
7.0
3 ea.
1
69
7.0
1
69
7.0
1
69
4.15 & 7.0
1 ea.
13
13A
69
69
4.15
4.15
3
3
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
11 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
9.4
QUALIFICATION TESTING
Qualification testing shall be performed on sample units produced with equipment and
procedures normally used in production. The test sequence shall be as shown in Table 1.
9.5 REQUALIFICATION TESTING
If either of the following conditions occurs, the responsible product engineer shall initiate
requalification testing consisting of all applicable parts of the qualification test matrix, Table
1.
A.
A significant design change is made to the existing product. A significant change
shall include, but is not limited to, changes in the contact material composition,
contact material thickness, contact force, contact surface geometry, underlying
material composition, underlying material thickness, insulator design, contact base
material, or contact lubrication requirements.
B.
C.
A significant change is made to the manufacturing process which impacts the
product form, fit, or function.
A significant event occurs during production or end use requiring corrective action to
be taken relative to the product design or manufacturing process.
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
12 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
TABLE 1 - QUALIFICATION TESTING
TEST GROUP
TEST/OPERATION
1
1
2
1
3
1
3
A
4
5
5
A
6
7
8
9
10 11 11 11 12 13 13
A
B
A
Product Examination
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10
-
8
2
14 14 10 11 11
5
2
4
2
4
2
4
2
7
2
5
2
5
2
4
2
-
2
12 12
Sample Preparation
Plating Thkns. and/or
Metal Exam.
Porosity
Contact Resistance
2
2
2
2
2
2
2
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6
-
-
-
-
-
4
-
-
-
-
-
-
-
-
4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
-
4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5
7
9
5
7
9
5
8
-
5
7
9
-
5
7
9
-
5
9
5
9
11 11
-
-
13 13
-
-
-
-
-
Current Rating
Insulation Resistance
-
-
-
-
-
-
-
-
-
-
2
6
8
3
9
4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Dielectric Withstanding
Voltage
Capacitance
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Mating Force
3
3
3
-
3
-
3
-
3
7
4
8
-
3
7
4
8
-
11 11
Unmating Force
4
4
4
-
4
-
4
-
12 12
-
-
-
-
-
-
-
-
-
-
-
Contact Retention
-
-
-
-
3
5
7
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Normal Force
Board Retention
Humidity
Thermal Shock
Thermal Shock Phase 1
Temp. & Hum. Phase 2
Hi Temp. Life
Mechanical Shock
Vibration
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9
-
-
10 10
-
-
5
7
-
-
-
-
-
-
-
4
6
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6
8
-
6
8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10 10
-
-
10
-
-
-
-
-
10
-
6
7
-
-
-
-
-
6
-
8
-
-
-
-
6
8
-
-
-
-
-
Durability (30 cycles)
Durability (200 Cycles)
Battelle Imfg
6
-
-
-
6
-
-
-
-
-
-
-
Resistance to IR Heat
Solderability
-
-
-
-
-
-
-
-
-
-
-
-
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
13 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
FIGURE 1.0
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
14 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
FIGURE 2.0
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
15 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
FIGURE 3.0
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
16 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
NUMBER
TITLE
TYPE
PRODUCT SPECIFICATION
GS-12-0977
PAGE
REVISION
DATE
17 of 17
C
AUTHORIZED BY
Conan Micro miniature Connector System
Janmy Zhou
Feb. 14, 2012
CLASSIFICATION
UNRESTRICTED
REVISION RECORD
Rev Page
Description
Created new product specification.
EC#
N/A
Date
7/22/11
A
ALL
B
PAGE Modify Item8.5 Vibration Test Method.
8
PAGE Modify Item8.6 IMFG Test Method.
8
8/23/11
ELX-N-
005346
ELX-N-
010292
C
2/14/12
PDS: Rev :C
STATUS:Released
Printed: Mar 13, 2012
Copyright FCI.
Form E-3701 – Revision C
GS-01-029
相关型号：
©2020 ICPDF网 联系我们和版权申明