KBPC2500MFU [FCI-CONNECTOR]
Bridge Rectifier Diode, 25A, 50V V(RRM),;
| 型号： | KBPC2500MFU |
| 厂家： | 
FCI CONNECTOR |
| 描述： | Bridge Rectifier Diode, 25A, 50V V(RRM), |
| 文件： | 总4页 (文件大小：378K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
25Amps
Single Phase Silicon Bridge
KBPC
Mechanical Data
Features
Case: Metal case
Surge overload ratings to 300 amperes
This series is UL listed under the Recognized
Component Index, file number E142814
The plastic material used carries Underwriters Laboratory
flammability recognition 94V-0
Terminals: Plated .25" (6.53mm) Faston
Mounting Position: Bolt down on heat-sink with silicone thermal
compound between bridges and mounting surface for
maximum heat transfer efficiency
Mounting Position: Any
Weight: 1.024 ounce, 29 grams (approx)
Universal 4-way terminals, snap-on, wrap-around,
solder or P.C. Board mounting
High temperature soldering guaranteed 265 C/10
seconds at 5 lbs (2.3kg) tension
Maximum Ratings & Thermal Characteristics
Rating at 25 C ambient temperature unless otherwise specified, Resistive or Inductive load, 60 Hz.
For Capacitive load derate current by 20%.
KBPC KBPC KBPC KBPC KBPC KBPC KBPC
2500 2501 2502 2504 2506 2508 2510
Parameter
Symbol
VRRM
VRMS
VDC
unit
V
Maximum repetitive peak reverse voltage
Maximum RMS bridge input voltage
Maximum DC blocking voltage
50
35
50
100
70
200
140
200
400
280
400
600
420
600
800
560
800
1000
700
V
V
100
1000
Maximum average forward rectified
output current at TA=55 C
IF(AV)
25
A
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
300
A
IFSM
I2 t
ReJA
VIS
2sec
A
374
2.1
Rating for fusing ( t<8.3ms)
C / W
Vac
Typical thermal resistance per element(1)
Isolation voltage from case to leads
2500
TJ,
TSTG
Operating junction and storage temperature
range
-55 to + 150
Electrical Characteristics
Rating at 25 C ambient temperature unless otherwise specified. Resistive or Inductive load, 60Hz.
For Capacitive load derate by 20 %.
KBPC KBPC KBPC KBPC KBPC KBPC KBPC
2500 2501 2502 2504 2506 2508 2510
Parameter
Symbol
Unit
V
Maximum instantaneous forward voltage drop
per leg at 12.5A
1.0
VF
10
500
Maximum DC reverse current at rated TA =25 C
A
IR
DC blocking voltage per element
TA =125 C
Notes: (1)Thermal resistance from Junction to Ambemton P.C.board mounting.
25Amps
Single Phase Silicon Bridge
o
Rating and Characteristic Curves ( TA= 25 C Unless otherwise noted )
KBPC2500 thru KBPC2510
Fig. 1 Derating Curve for
Output Rectified Current
30
Fig. 2 Maximum Non-repetitive Peak
Forward Surge Current
400
8.3ms
Single half-sine-Wave
[JEDEC Method]
300
20
200
10
100
40
60Hz Resistive or
Inductive Load
0
0
1
10
100
50
100
o
150
Number of Cycles at 60HZ
Case Temperature, C
Fig. 4 Typical Reverse
Characteristics at Tj=25oC
Fig. 3 Typical Instantaneous
Forward Characteristics
100
10
1.0
0.1
.01
Tj= 100 C
10
1.0
0.1
.01
Tj= 25 C
Pulse Width= 300us
2% duty cycle
Tj= 25 C
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0
20
40
60
80
100
120
140
Percent of Rated Peak Reverse
Voltage, %
Instantaneous Forward
Voltage, Volts
25Amps
Single Phase Silicon Bridge
Ratings at
25 Deg. C ambient
temperature
unless otherwise
specified.
Single Phase Half
Wave, 60 HZ
Resistive or
Inductive Load.
For Capacitive
Load, Derate
Current by 20%.
NOTES: 1. Corrosion-Resistant Terminals Designed for .250" Female Quick Connect Wrap Around
or Solder.
2. A Thin Film of Silicone Thermal Compound is Recommended Between Bridge and
Mounting Surface for Improved Thermal Conduction.
3. These FCI Bridges Are Also Available in Fast Recovery, In Positive and Negative Center
Tap and in Double Configurations. Consult with FCI for Your Special Requirements.
25Amps
Single Phase Silicon Bridge
Case - Metal or Molded Plastic
AC In
Terminals - Plated .25" Faston or Plated Copper Wire
Leads .040" Diameter
Weight - 0.706 Ounces, 20 Grams
Mounting Position - Any with Bolt Down with Silicone
Thermal Compound Between Bridge and
Mounting Surface for Optimum Heat
Transfer
DC Out
Mounting Torque - 20 Inch Pound Max
Ordering Information
FCIS KBPC Series of Bridges Can Be Ordered with Options on Terminals and Case Materials.
How To Specify Case Material and Terminal Options:
n For Metal Case, Order Suffix (1) M
n For Plastic Case, Order Suffix (1) P
n For Faston Terminals, Order Suffix (2) F
n For Wire Lead Terminals, Order Suffix (2) W
KBPC Series Examples
To Order a 25 Amp, 400 Volt Bridge with Faston Leads and a Plastic Case:
Specify - KBPC2504PF . . . Where P = Plastic and F = Faston Terminals
To Order a 35 Amp, 800 Volt Bridge with Wire Leads and a Metal Case:
Specify - KBPC3508MW . . . Where M = Metal and W = Wire Leads (Terminals)
To Order a 15 Amp, 200 Volt, UL Recognized Bridge with Wire Leads and a Plastic Case:
Specify - KBPC1502PWU . . . Where P = Plastic and W = Wire Leads (Terminals) and U = UL Recognized
NOTE: Fast Recovery Bridges (Diodes) Are Available; Please Contact FCI Components.
KBPC - S Series Examples
To Order Bridges with the In-Line Pin Configuration, Select the Current and Voltage Desired and Add S as the Suffix, as
shown in the following example.
To Order a 35 Amp, 800 Volt Bridge with In-Line Wire Leads:
Specify - KBPC3508S . . . Where S = In-Line Wire Lead Terminals
相关型号：
KBPC2500P-LF
Bridge Rectifier Diode, 1 Phase, 25A, 50V V(RRM), Silicon, ROHS COMPLIANT, PLASTIC, KBPC-P, 4 PIN
WTE
KBPC2500PW-G
Bridge Rectifier Diode, 1 Phase, 25A, 50V V(RRM), Silicon, PLASTIC, KBPC-PW, 4 PIN
SENSITRON
KBPC2500PW-LF
Bridge Rectifier Diode, 1 Phase, 25A, 50V V(RRM), Silicon, ROHS COMPLIANT, PLASTIC, KBPC-PW, 4 PIN
WTE
©2020 ICPDF网 联系我们和版权申明