FWLF1634RY37 [FINISAR]
4Gbps Long-Reach DWDM SFP Transceiver; 4Gbps的长距离DWDM SFP收发器型号: | FWLF1634RY37 |
厂家: | FINISAR CORPORATION. |
描述: | 4Gbps Long-Reach DWDM SFP Transceiver |
文件: | 总10页 (文件大小:204K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
F i n i s a r
Preliminary Product Specification
4Gbps Long-Reach DWDM SFP Transceiver
FWLF1634Ryxx
PRODUCT FEATURES
• Up to 4.25 Gb/s bi-directional links
• Hot-pluggable SFP footprint
• Temperature-stabilized DWDM-
rated DFB laser transmitter
• 100GHz ITU Grid, C-Band
• Low dispersion DFB laser
• Extended operating range: -5°C to
70°C case temperature
APPLICATIONS
• Wavelength controlled within ± 0.1
nm over life and temperature
• Amplified DWDM networks
• Bandwidth aggregation
• Extended link budget with APD
receiver technology
• Ring topologies with fixed and
• 4x FC compliant
reconfigurable OADMs
• 1x/2x, GbE compliant*
• OC-48 LR-2 compliant*
Finisar’s Dense Wavelength-Division Multiplexing (DWDM) transceivers offer DWDM
transport with dramatically lower power and cost in a standard pluggable Small Form
Factor Pluggable (SFP) package1. The FWLF1634R is designed expressly for service
providers deploying DWDM networking equipment in metropolitan access and core
networks.
Basic digital diagnostic features for the FWLF1634R are implemented as described in
Finisar Application Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical
Transceivers”4. Enhanced diagnostic features are available as described in the DWDM
SFP MSA6.
(*when ordered with rate selection option, and used in low rate mode)
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 1
F i n i s a r
PRODUCT SELECTION
FWLF1634Ryxx
L
V
Non Rate Selectable - 4x Fibre Channel
Rate Selectable - 1x, 2x, Fibre Channel, Gigabit Ethernet
DWDM Wavelength (see table below)
y
xx
Product Code
FWLF1634Ry17
FWLF1634Ry18
FWLF1634Ry19
FWLF1634Ry20
FWLF1634Ry21
FWLF1634Ry22
FWLF1634Ry23
FWLF1634Ry24
FWLF1634Ry25
FWLF1634Ry26
FWLF1634Ry27
FWLF1634Ry28
FWLF1634Ry29
FWLF1634Ry30
FWLF1634Ry31
FWLF1634Ry32
FWLF1634Ry33
FWLF1634Ry34
FWLF1634Ry35
FWLF1634Ry36
FWLF1634Ry37
FWLF1634Ry38
FWLF1634Ry39
FWLF1634Ry40
FWLF1634Ry41
FWLF1634Ry42
FWLF1634Ry43
FWLF1634Ry44
FWLF1634Ry45
FWLF1634Ry46
FWLF1634Ry47
FWLF1634Ry48
FWLF1634Ry49
FWLF1634Ry50
FWLF1634Ry51
FWLF1634Ry52
FWLF1634Ry53
FWLF1634Ry54
FWLF1634Ry55
FWLF1634Ry56
FWLF1634Ry57
FWLF1634Ry58
FWLF1634Ry59
FWLF1634Ry60
FWLF1634Ry61
Frequency (THz)
191.7
191.8
191.9
192.0
192.1
192.2
192.3
192.4
192.5
192.6
192.7
192.8
192.9
193.0
193.1
193.2
193.3
193.4
193.5
193.6
193.7
193.8
193.9
194.0
194.1
194.2
194.3
194.4
194.5
194.6
194.7
194.8
194.9
195.0
195.1
195.2
195.3
195.4
195.5
195.6
195.7
195.8
195.9
196.0
196.1
Center Wavelength (nm)
1563.86
1563.05
1562.23
1561.42
1560.61
1559.79
1558.98
1558.17
1557.36
1556.55
1555.75
1554.94
1554.13
1553.33
1552.52
1551.72
1550.92
1550.12
1549.32
1548.51
1547.72
1546.92
1546.12
1545.32
1544.53
1543.73
1542.94
1542.14
1541.35
1540.56
1539.77
1538.98
1538.19
1537.40
1536.61
1535.82
1535.04
1534.25
1533.47
1532.68
1531.90
1531.12
1530.33
1529.55
1528.77
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 2
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
I.
Pin Descriptions
Pin
Symbol
Name/Description
Ref.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
VEET
TFAULT
TDIS
Transmitter Ground (Common with Receiver Ground)
Transmitter Fault
Transmitter Disable. Laser output disabled on high or open
1
2
3
3
3
4
5
1
1
1
MOD_DEF(2) Module Definition 2. Data line for Serial ID
MOD_DEF(1) Module Definition 1. Clock line for Serial ID
MOD_DEF(0) Module Definition 0. Grounded within the module
Rate Select
LOS
No connection required
Loss of Signal indication. Logic 0 indicates normal operation
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Inverted DATA out. AC Coupled
Receiver Non-inverted DATA out. AC Coupled
Receiver Ground (Common with Transmitter Ground)
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground (Common with Receiver Ground)
Transmitter Non-Inverted DATA in. 100 ohm termination between TD+
and TD-, AC Coupled thereafter
VEER
VEER
VEER
RD-
RD+
VEER
VCCR
VCCT
VEET
1
1
TD+
19
20
TD-
VEET
Transmitter Inverted DATA in. See TD+
Transmitter Ground (Common with Receiver Ground)
1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 5.5V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Receiver achieves multi-rate operation without active control.
5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and
5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
VeeT
TD-
20
19
18
17
16
15
14
13
12
11
VeeT
1
2
TXFault
TD+
3
TX Disable
MOD-DEF(2)
MOD-DEF(1)
MOD-DEF(0)
Rate Select
LOS
VeeT
VccT
VccR
VeeR
RD+
RD-
4
5
Towards
Bezel
Towards
ASIC
6
7
8
9
VeeR
VeeR
VeeR
10
Diagram of Host Board Connector Block Pin Numbers and Names
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 3
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage
Storage Temperature
Symbol
Vcc
TS
Min
-0.5
-10
-5
Typ
Max
4.7
85
Unit
V
°C
Case Operating Temperature
TOP
70
°C
III.
Electrical Characteristics (TOP = -5 to 70 °C, VCC = 3.13 to 3.50 Volts)
Parameter
Symbol
Vcc
Icc
Isurge
Pmax
Min
3.13
Typ
3.30
Max
3.50
325
Icc+30
1.25
Unit
V
mA
mA
W
Ref.
Supply Voltage
Supply Current
Inrush Current
BOL
BOL
Maximum Power
TRANSMITTER
Input differential impedance
Single ended data input swing
Transmit Disable Voltage
Transmit Enable Voltage
RECEIVER
Rin
Vin,pp
VD
100
1
2
Ω
mV
V
250
Vcc – 1.3
Vee
1200
Vcc
Vee+ 0.8
VEN
V
Single ended data output swing
Data output rise time
Data output fall time
LOS Fault
Vout,pp
175
1000
120
120
mV
ps
ps
3
4
4
5
tr
tf
VLOS fault
Vcc – 0.5
VccHOST
V
LOS Normal
Power Supply Rejection
VLOS norm
PSR
Vee
100
Vee+0.5
V
mVpp
5
6
Notes:
1.
2.
3.
4.
5.
6.
Connected directly to TX data input pins. AC coupled thereafter.
Or open circuit.
Into 100 ohms differential termination.
20 – 80 %
Loss of signal (LOS) is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified
value applied through the recommended power supply filtering network.
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 4
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
IV.
Low Speed Signals
Parameter
Symbol Min Typ Max Units Notes/Conditions
RX_LOS Assert Level
RX_LOS De-assert Level
RX_LOS Hysteresis
-42
0.5
-36
-34
2
dBm
dBm
dB
-28
100
100
10
RX_LOS Assert Delay
t_loss_on
t_loss_off
t_off
From detection of loss of signal
to assertion of RX_LOS
µsec
RX_LOS Negate Delay
From detection of presence of
signal to negation of RX_LOS
µsec
µsec
TX_DISABLE Assert Time
Rising edge of TX_DISABLE to
fall of output signal below 10%
of nominal
TX_DISABLE Negate Time
t_on
1000
Falling edge of TX_DISABLE
to rise of output signal above
90% of nominal. Time
µsec
indicated is under steady-state
temperature conditions.
TX_DISABLE Reset Time
TX_FAULT Assert
t_reset
10
TX_DISABLE HIGH before
TX_DISABLE set LOW
µsec
-0.2
+0.2
nm TX_Fault will assert before the
device is outside of specified
wavelength range
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 5
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
V.
Optical Parameters1
Parameter
Symbol
Min
Typ
Max
Units Notes/Conditions
TRANSMITTER CHARACTERISTICS
Center Wavelength Spacing
Modulated Spectral Width
Corresponds to approximately 0.8 nm
100
0.2
GHz
0.3
nm Full width, -20dB from max.
See note 3
∆λ 20
X = specified center wavelength
Center Wavelength – End of Life
Center Wavelength – BOL Offset
Side Mode Suppression Ratio
Optical Rise/Fall Time
Optical Output Power
X - 100
Y - 25
30
X
Y
X + 100 pm
λc
λc
SMSR
tr / tf
Pout
Y = specified center wavelength
Y + 25
pm
dB Modulated
120
+5
ps
dBm
Unfiltered, 80% -20%
Avg. power coupled into SMF-28; see
note 4
+2
Extinction Ratio, (<=4.25G)
Extinction Ratio, SONET
Eye Opening
OMI
OMI
6.0
8.2
10
dB EOL
EOL, Rate Select Option Only
dB
%
Jitter Generation, SONET
75
mUI Parameters per GR-2532
section 5.6 for OC-48 B
Total Jitter
Deterministic Jitter
Reflectance
Tolerable Back Reflection
Relative Intensity Noise
Dispersion Power Penalty
RECEIVER CHARACTERISTICS
Optical Input Wavelength
59.8
28.2
-27
ps
ps
dB
(p-to-p)
(p-to-p)
RTX
BR
RIN
DPP
-14
dB See note 5
-120 dB/Hz
3.0
dB At 1600 ps/nm. See Note 6
Pin
1520
1570
75
nm
Jitter Generation , SONET
mUI Parameters per GR-2532
section 5.6 for OC-48 B
Total Jitter
61.8
25.9
-9
ps
ps
(p-to-p)
(p-to-p)
Deterministic Jitter
Optical Input Power
Pin
Pin
-28
-23
dBm 2.5 Gb/s w/ PRBS 2 23 -1
EOL, & rate select low option
implemented
(BER < 10 -12
)
Optical Input Power
(BER < 10 -12
Optical Input Power –
Receiver Damage Threshold
Receiver Reflectance
-9
+6
-27
dBm 4.25 Gb/s w/ PRBS 2 7 -1
EOL
dBm
)
RRX
dB
Min-Required OSNR 0ps/nm
Min-Required OSNR 1600ps/nm
OSNRbb
OSNRt
22
25
dB See Note 7
dB See Note 7
Notes:
1. Parameters are specified over temperature and voltage, at end of life, and for non-rate select option unless otherwise noted.
2. All parameters are measured on a Finisar SFP Evaluation Card unless otherwise noted.
3. For accurate ∆λ20 measurements, an OSA with a resolution band width of ≤ 20pm is recommended.
4. Output power of +3 to +7dBm is also supported; please contact your local Finisar sales representatives for details.
5. Tolerable back reflection is the max back reflection level at which the power penalty will be <1dB. Power penalty is measured
over fiber (1600ps/nm) at BER = 10-12 with OSNR set at 24dB.
6. Dispersion power penalty is measured in loop back with OSNR set to 30 dB. Data rate and pattern used same as specified for
Optical Input Power. Dispersion power penalty is the difference in Rx power at a BER of 10-12 for 0ps/nm & 1600ps/nm
7. Rx power set between -9dBm and -18dBm. Data rate and pattern used same as specified for Optical Input Power. Measured as
the Minimum OSNR to achieve a BER of 10-12 . Optical filter bandwidth of 0.1nm is used in OSNR measurement.
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 6
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
VI. Wavelength Stabilization
The laser transmitter will not be turned on until its temperature is adjusted to ensure
operation within the specified channel (X +/- 300pm). This temperature stabilization time is
dependent on the ambient temperature conditions, but will typically occur within 5 seconds
of powering the device. The module will transmit within the specified wavelength tolerance
(X +/- 100pm) within 10 ms of transmitter operation.
VII. General Specifications
Parameter
Symbol
Min
Typ
Max
Units Notes/Conditions
Data Rate
Total Link Budget
BR
0.155
26
4.25
Gb/sec SONET OC-3/12/48 compatible
30
34
dB @ 4.25 Gb/s, BER <10-12 w/
PRBS 2 7-1. See Note 1
Total Link Budget
31
dB @ 2.5 Gb/s, BER <10-12 w/ PRBS
2 23-1. See Note 1
Note 1: Total link budget is defined as Pout – Pin – typical connector losses. Operating in low rate mode
VIII. Environmental Specifications
Parameter
Symbol Min
Typ Max Units Notes/Conditions
Operating Temp
Top
Tsto
-5
70
85
°C Case temperature measured on top-side of
device
Storage Temp
Eye Safety
-40
°C Ambient temperature
CDRH and IEC-825 Class 1 Laser
Product. See Note 1
Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No.
50, dated July 26, 2001.
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 7
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
IX. Serial Communication Protocol
All Finisar SFPs support the 2-wire serial communication protocol to provide module ID
information as outlined in the SFP MSA1. These SFPs use an Atmel AT24C01A 128 byte
E2PROM with an address of A0h. For details on interfacing with the E2PROM, see the
Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”3
Finisar SFPs also support diagnostic features as described in Finisar Applications Note AN-
20304 and SFF-84725, “Digital Diagnostic Monitoring Interface for Optical Transceivers”.
A controller IC that monitors system parameters such as laser current, module temperature,
transmitter power, and received power is accessible at address A2H. In addition, Finisar’s
DWDM SFPs provide extended set of ID information and diagnostic features as described
in the DWDM SFP MSA6.
I2C clock speed, digital diagnostic accuracy and digital diagnostic range can be found in the
table below. Values in the table represent the worst-case values over temperature, voltage,
and life.
Parameter
I2C Clock Speed
Accuracy
Transceiver Case
Temperature
Transceiver Supply
Voltage
Symbol Min Typ Max Units Notes/Conditions
0
100,000
Hz
°C
%
Bus can be driven blind
DDTemperature -10
+10
Measured on the top-side of
the module case
DDVoltage
-3
+3
Tx Bias Current
Tx Output Power
Received Average
Power
DDBias
DDTxPower
DDRxPower
-10
-2
-2
+10
+2
+2
%
dB
dB
Range
Transceiver Case
Temperature
Transceiver Supply
Voltage
DDTemperature -40
85
°C
V
DDVoltage
3.0
4.0
Tx Bias Current
Tx Output Power
Received Average
Power
DDBias
DDTxPower
DDRxPower
0
-5
-30
90
+10
-7
mA
dBm
dBm
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 8
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
X.
Mechanical Specifications
Finisar’s Multi-rate DWDM Small Form Factor Pluggable (SFP) transceivers are
compatible with the dimensions defined by the DWDM SFP Multi-Sourcing Agreement
(MSA)6.
Figure 1. DWDM SFP Outline Drawing (units in inches [mm])
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 9
FWLF1634Ryxx DWDM SFP Preliminary Product Specification – February 2009
F i n i s a r
XI. Ordering Information
Part Number
Description
FWLF1634Ryxx
DWDM SFP with APD Receiver
y = L: non rate select
y = V: rate select
xx = channel number (see product selection on page 2)
XII. References
1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available from Finisar upon request.
2. “SONET Transport Systems: Common Generic Criteria”, Telcordia Technologies,
GR-253-CORE, Issue 3, September 2000.
3. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”, Atmel Corporation.
www.Atmel.com.
4. “Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical
Transceivers”, Finisar Corporation, April 2002.
5. “Digital Diagnostic Monitoring Interface For Optical Transceivers Rev 9.3”. SFF
Document No. SFF-8472.
6. Specifications for DWDM SFP Transceiver Draft 1.0.October 21 2005.
Documentation is available from Finisar upon request.
XIII. For More Information:
Finisar Corporation
1308 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. (408) 548-1000
Fax (408) 541-6138
sales@finisar.com
www.finisar.com
Finisar Corporation
Rev C2, Feb.2009
PRELIMINARY
Page 10
相关型号:
©2020 ICPDF网 联系我们和版权申明