MCF52233CAL60 [FREESCALE]
MCF52235 ColdFire Microcontroller Data Sheet; MCF52235的ColdFire微控制器数据表型号: | MCF52233CAL60 |
厂家: | Freescale |
描述: | MCF52235 ColdFire Microcontroller Data Sheet |
文件: | 总54页 (文件大小:1018K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Freescale Semiconductor
Data Sheet: Technical Data
Document Number: MCF52235DS
Rev. 9, 7/2010
MCF52235
LQFP-80
LQFP-112
14mm x 14mm
20mm_x_20mm
MAPBGA-121
12mm_x_12mm
MCF52235 ColdFire
Microcontroller Data Sheet
®
The MCF52235 is a member of the ColdFire family of
• Two 16-bit periodic interrupt timers (PITs)
• Real-time clock (RTC) module
• Programmable software watchdog timer
• Two interrupt controllers providing every peripheral with a
unique selectable-priority interrupt vector plus seven
external interrupts with fixed levels/priorities
• Clock module with support for crystal or external oscillator
and integrated phase-locked loop (PLL)
reduced instruction set computing (RISC) microcontrollers.
This document provides an overview of the MCF52235
microcontroller family, focusing on its highly integrated and
diverse feature set.
This 32-bit device is based on the Version 2 ColdFire core
operating at a frequency up to 60 MHz, offering high
performance and low power consumption. On-chip memories
connected tightly to the processor core include up to 256
Kbytes of Flash and 32 Kbytes of static random access
memory (SRAM). On-chip modules include:
• V2 ColdFire core providing 56 Dhrystone 2.1 MIPS @ 60
MHz executing out of on-chip Flash memory using
enhanced multiply accumulate (EMAC) and hardware
divider
• Test access/debug port (JTAG, BDM)
• Enhanced Multiply Accumulate Unit (EMAC) and
hardware divide module
• Cryptographic Acceleration Unit (CAU) coprocessor
• Fast Ethernet Controller (FEC)
• On-chip Ethernet Transceiver (EPHY)
• FlexCAN controller area network (CAN) module
• Three universal asynchronous/synchronous
receiver/transmitters (UARTs)
• Inter-integrated circuit (I2C™) bus controller
• Queued serial peripheral interface (QSPI) module
• Eight-channel 10- or 12-bit fast analog-to-digital converter
(ADC)
• Four channel direct memory access (DMA) controller
• Four 32-bit input capture/output compare timers with
DMA support (DTIM)
• Four-channel general-purpose timer (GPT) capable of
input capture/output compare, pulse width modulation
(PWM) and pulse accumulation
• Eight/Four-channel 8/16-bit pulse width modulation timers
(two adjacent 8-bit PWMs can be concatenated to form a
single 16-bit timer)
Freescale reserves the right to change the detail specifications as may be required to permit
improvements in the design of its products.
© Freescale Semiconductor, Inc., 2010. All rights reserved.
Table of Contents
MCF52235 Family Configurations . . . . . . . . . . . . . . . . . . . . . .3
1
Figure 14.Test Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 15.Boundary Scan (JTAG) Timing . . . . . . . . . . . . . . . . . 45
Figure 16.Test Access Port Timing . . . . . . . . . . . . . . . . . . . . . . 45
Figure 17.TRST Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 18.Real-Time Trace AC Timing. . . . . . . . . . . . . . . . . . . . 46
Figure 19.BDM Serial Port AC Timing . . . . . . . . . . . . . . . . . . . . 46
1.1 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.3 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.4 PLL and Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . .22
1.5 Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
1.6 External Interrupt Signals . . . . . . . . . . . . . . . . . . . . . . .22
1.7 Queued Serial Peripheral Interface (QSPI). . . . . . . . . .23
1.8 Fast Ethernet Controller EPHY Signals . . . . . . . . . . . .23
1.9 I2C I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
1.10 UART Module Signals. . . . . . . . . . . . . . . . . . . . . . . . . .24
1.11 DMA Timer Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . .24
1.12 ADC Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
1.13 General Purpose Timer Signals . . . . . . . . . . . . . . . . . .25
1.14 Pulse Width Modulator Signals. . . . . . . . . . . . . . . . . . .25
1.15 Debug Support Signals. . . . . . . . . . . . . . . . . . . . . . . . .25
1.16 EzPort Signal Descriptions . . . . . . . . . . . . . . . . . . . . . .27
1.17 Power and Ground Pins . . . . . . . . . . . . . . . . . . . . . . . .27
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
2.1 Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2.2 ESD Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2.3 DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . .32
2.4 Phase Lock Loop Electrical Specifications . . . . . . . . . .33
2.5 General Purpose I/O Timing . . . . . . . . . . . . . . . . . . . . .35
2.6 Reset Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
2.7 I2C Input/Output Timing Specifications. . . . . . . . . . . . .36
2.8 EPHY Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
2.9 Analog-to-Digital Converter (ADC) Parameters . . . . . .40
2.10 DMA Timers Timing Specifications. . . . . . . . . . . . . . . .42
2.11 EzPort Electrical Specifications . . . . . . . . . . . . . . . . . .42
2.12 QSPI Electrical Specifications. . . . . . . . . . . . . . . . . . . .43
2.13 JTAG and Boundary Scan Timing. . . . . . . . . . . . . . . . .44
2.14 Debug AC Timing Specifications. . . . . . . . . . . . . . . . . .46
Mechanical Outline Drawings . . . . . . . . . . . . . . . . . . . . . . . . .47
3.1 80-pin LQFP Package. . . . . . . . . . . . . . . . . . . . . . . . . .47
3.2 112-pin LQFP Package. . . . . . . . . . . . . . . . . . . . . . . . .48
3.3 121 MAPBGA Package. . . . . . . . . . . . . . . . . . . . . . . . .51
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
List of Tables
Table 1. MCF52235 Family Configurations . . . . . . . . . . . . . . . . . 3
Table 2. Orderable Part Number Summary. . . . . . . . . . . . . . . . 13
Table 3. Pin Functions by Primary and Alternate Purpose . . . . 17
Table 4. Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 5. PLL and Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 6. Mode Selection Signals. . . . . . . . . . . . . . . . . . . . . . . . 22
Table 7. External Interrupt Signals . . . . . . . . . . . . . . . . . . . . . . 22
Table 8. Queued Serial Peripheral Interface (QSPI) Signals. . . 23
Table 9. Fast Ethernet Controller (FEC) Signals . . . . . . . . . . . . 23
Table 10.I2C I/O Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 11.UART Module Signals . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 12.DMA Timer Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 13.ADC Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 14.GPT Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 15.PWM Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 16.Debug Support Signals . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 17.EzPort Signal Descriptions . . . . . . . . . . . . . . . . . . . . . 27
Table 18.Power and Ground Pins. . . . . . . . . . . . . . . . . . . . . . . . 27
Table 19.Absolute Maximum Ratings, . . . . . . . . . . . . . . . . . . . 29
Table 20.Thermal Characteristics. . . . . . . . . . . . . . . . . . . . . . . . 30
Table 21.ESD Protection Characteristics . . . . . . . . . . . . . . . . . . 31
Table 22.DC Electrical Specifications . . . . . . . . . . . . . . . . . . . . 32
Table 23.Active Current Consumption Specifications. . . . . . . . . 33
Table 24.Current Consumption Specifications in
2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 25.PLL Electrical Specifications . . . . . . . . . . . . . . . . . . . . 33
Table 26.GPIO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 27.Reset and Configuration Override Timing . . . . . . . . . . 35
Table 28.I2C Input Timing Specifications between
3
4
I2C_SCL and I2C_SDA . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 29. I2C Output Timing Specifications between
List of Figures
I2C_SCL and I2C_SDA . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 1.MCF52235 Block Diagram . . . . . . . . . . . . . . . . . . . . . . 4
Figure 2.80-pin LQFP Pin Assignments . . . . . . . . . . . . . . . . . . 14
Figure 3.112-pin LQFP Pin Assignments . . . . . . . . . . . . . . . . . 15
Figure 4.121 MAPBGA Pin Assignments . . . . . . . . . . . . . . . . . 16
Figure 5.Suggested Connection Scheme for Power and Ground 28
Figure 6.GPIO Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 7.RSTI and Configuration Override Timing . . . . . . . . . . 36
Figure 8.I2C Input/Output Timings . . . . . . . . . . . . . . . . . . . . . . 37
Figure 9.EPHY Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 10.10BASE-T SQE (Heartbeat) Timing . . . . . . . . . . . . . 39
Figure 11.10BASE-T Jab and Unjab Timing . . . . . . . . . . . . . . . 39
Figure 12.Equivalent Circuit for A/D Loading. . . . . . . . . . . . . . . 42
Figure 13.QSPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 30.EPHY Timing Parameters . . . . . . . . . . . . . . . . . . . . . . 38
Table 31.10BASE-T SQE (Heartbeat) Timing Parameters . . . . 38
Table 32.10BASE-T Jab and Unjab Timing Parameters . . . . . . 39
Table 33.10BASE-T Transceiver Characteristics . . . . . . . . . . . . 40
Table 34.100BASE-TX Transceiver Characteristics . . . . . . . . . . 40
Table 35.ADC Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 36.Timer Module AC Timing Specifications . . . . . . . . . . . 42
Table 37.EzPort Electrical Specifications. . . . . . . . . . . . . . . . . . 42
Table 38.QSPI Modules AC Timing Specifications. . . . . . . . . . . 43
Table 39.JTAG and Boundary Scan Timing . . . . . . . . . . . . . . . . 44
Table 40.Debug AC Timing Specification. . . . . . . . . . . . . . . . . . 46
Table 41.Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
2
Freescale Semiconductor
MCF52235 Family Configurations
1 MCF52235 Family Configurations
Table 1. MCF52235 Family Configurations
Module
52230
52231
52232
52233
52234
52235
52236
Version 2 ColdFire Core with EMAC
(Enhanced Multiply-Accumulate Unit)
•
•
•
•
•
•
•
System Clock (MHz)
60
56
60
56
50
46
60
56
60
56
60
56
50
46
Performance (Dhrystone 2.1 MIPS)
Flash / Static RAM (SRAM)
128/32
Kbytes
128/32
Kbytes
128/32
Kbytes
256/32
Kbytes
256/32
Kbytes
256/32
Kbytes
256/32
Kbytes
Interrupt Controllers (INTC0/INTC1)
Fast Analog-to-Digital Converter (ADC)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Random Number Generator and Crypto
Acceleration Unit (CAU)
—
—
—
—
—
—
FlexCAN 2.0B Module
—
•
•
—
—
•
•
•
•
—
Fast Ethernet Controller (FEC) with on-chip
interface (EPHY)
•
•
•
•
Four-channel Direct-Memory Access (DMA)
Software Watchdog Timer (WDT)
Programmable Interrupt Timer
Four-Channel General Purpose Timer
32-bit DMA Timers
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
•
•
2
•
4
•
3
•
•
•
•
QSPI
UART(s)
I2C
Eight/Four-channel 8/16-bit PWM Timer
General Purpose I/O Module (GPIO)
Chip Configuration and Reset Controller
Module
Background Debug Mode (BDM)
JTAG - IEEE 1149.1 Test Access Port1
Package
•
•
•
•
•
•
•
•
•
•
•
•
•
•
80 LQFP 80 LQFP 80 LQFP 80 LQFP 112 LQFP 112 LQFP 80 LQFP
112 LQFP 112 LQFP 112 LQFP 121 121
MAPBGA MAPBGA
1
The full debug/trace interface is available only on the 112- and 121-pin packages. A reduced debug interface is bonded on the
80-pin package.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
3
MCF52235 Family Configurations
1.1
Block Diagram
The MCF52235 (or its variants) comes in 80- and 112-pin low-profile quad flat pack packages (LQFP) and a 121 MAPBGA,
and operates in single-chip mode only. Figure 1 shows a top-level block diagram of the MCF52235.
EzPD
EzPQ
EzPCK
EzPCS
EPHY_TX
EPHY_RX
EzPort
Arbiter
GPTn
QSPI_DIN,
QSPI_DOUT
Interrupt
Controller 1
Interrupt
Controller 2
EPHY
QSPI_CLK,
QSPI_CSn
SDA
Fast
SCL
Ethernet
Controller
(FEC)
UTXDn
URXDn
URTSn
UCTSn
DTINn/DTOUTn
CANRX
CANTX
PWMn
UART
0
UART
1
UART
2
I2C
QSPI
RTC
4 CH DMA
DTIM
0
DTIM
1
DTIM
2
DTIM
3
To/From PADI
MUX
JTAG_EN
V2 ColdFire CPU
CAU
IFP OEP
EMAC
PMM
CIM
JTAG
TAP
32 Kbytes
SRAM
256 Kbytes
Flash
(32K×16)×4
RSTIN
PORTS
(GPIO)
AN[7:0]
ADC
RSTOUT
(4K×16)×4
VRH VRL
PLL
CLKGEN
Edge
Port 1
PWM
PIT1
FlexCAN
Edge
Port 2
EXTAL XTAL CLKOUT
GPT
PIT0
RNGA
To/From Interrupt Controller
Figure 1. MCF52235 Block Diagram
1.2
Features
This document contains information on a new product under development. Freescale reserves the right to change or discontinue
this product without notice. Specifications and information herein are subject to change without notice.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
4
Freescale Semiconductor
MCF52235 Family Configurations
1.2.1 Feature Overview
The MCF52235 family includes the following features:
•
Version 2 ColdFire variable-length RISC processor core
— Static operation
— 32-bit address and data paths on-chip
— Up to 60 MHz processor core frequency
— Sixteen general-purpose, 32-bit data and address registers
— Implements ColdFire ISA_A with extensions to support the user stack pointer register and four new instructions
for improved bit processing (ISA_A+)
— Enhanced Multiply-Accumulate (EMAC) unit with 32-bit accumulator to support 16 × 16 → 32 or 32 × 32 → 32
operations
— Cryptography Acceleration Unit (CAU)
–
–
Tightly-coupled coprocessor to accelerate software-based encryption and message digest functions
FIPS-140 compliant random number generator
— Support for DES, 3DES, AES, MD5, and SHA-1 algorithms
— Illegal instruction decode that allows for 68K emulation support
System debug support
•
— Real time trace for determining dynamic execution path
— Background debug mode (BDM) for in-circuit debugging (DEBUG_B+)
— Real time debug support, with six hardware breakpoints (4 PC, 1 address and 1 data) that can be configured into
a 1- or 2-level trigger
•
•
On-chip memories
— Up to 32 Kbytes of dual-ported SRAM on CPU internal bus, supporting core and DMA access with standby power
supply support
— Up to 256 Kbytes of interleaved Flash memory supporting 2-1-1-1 accesses
Power management
— Fully static operation with processor sleep and whole chip stop modes
— Rapid response to interrupts from the low-power sleep mode (wake-up feature)
— Clock enable/disable for each peripheral when not used
Fast Ethernet Controller (FEC)
•
•
— 10/100 BaseT/TX capability, half duplex or full duplex
— On-chip transmit and receive FIFOs
— Built-in dedicated DMA controller
— Memory-based flexible descriptor rings
On-chip Ethernet Transceiver (EPHY)
— Digital adaptive equalization
— Supports auto-negotiation
— Baseline wander correction
— Full-/Half-duplex support in all modes
— Loopback modes
— Supports MDIO preamble suppression
— Jumbo packet
•
FlexCAN 2.0B module
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
5
MCF52235 Family Configurations
— Based on and includes all existing features of the Freescale TouCAN module
— Full implementation of the CAN protocol specification version 2.0B
–
–
–
–
Standard Data and Remote Frames (up to 109 bits long)
Extended Data and Remote Frames (up to 127 bits long)
0–8 bytes data length
Programmable bit rate up to 1 Mbit/sec
— Flexible Message Buffers (MBs), totalling up to 16 message buffers of 0–8 byte data length each, configurable as
Rx or Tx, all supporting standard and extended messages
— Unused Message Buffer space can be used as general purpose RAM space
— Listen only mode capability
— Content-related addressing
— No read/write semaphores required
— Three programmable mask registers: global for MBs 0-13, special for MB14, and special for MB15
— Programmable transmit-first scheme: lowest ID or lowest buffer number
— Time stamp based on 16-bit free-running timer
— Global network time, synchronized by a specific message
— Maskable interrupts
•
Three universal asynchronous/synchronous receiver transmitters (UARTs)
— 16-bit divider for clock generation
— Interrupt control logic with maskable interrupts
— DMA support
— Data formats can be 5, 6, 7 or 8 bits with even, odd or no parity
— Up to 2 stop bits in 1/16 increments
— Error-detection capabilities
— Modem support includes request-to-send (RTS) and clear-to-send (CTS) lines for two UARTs
— Transmit and receive FIFO buffers
•
•
I2C module
— Interchip bus interface for EEPROMs, LCD controllers, A/D converters, and keypads
— Fully compatible with industry-standard I2C bus
— Master and slave modes support multiple masters
— Automatic interrupt generation with programmable level
Queued serial peripheral interface (QSPI)
— Full-duplex, three-wire synchronous transfers
— Up to four chip selects available
— Master mode operation only
— Programmable bit rates up to half the CPU clock frequency
— Up to 16 pre-programmed transfers
•
Fast analog-to-digital converter (ADC)
— Eight analog input channels
— 12-bit resolution
— Minimum 1.125 μs conversion time
— Simultaneous sampling of two channels for motor control applications
— Single-scan or continuous operation
— Optional interrupts on conversion complete, zero crossing (sign change), or under/over low/high limit
— Unused analog channels can be used as digital I/O
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
6
Freescale Semiconductor
MCF52235 Family Configurations
•
Four 32-bit DMA timers
— 17-ns resolution at 60 MHz
— Programmable sources for clock input, including an external clock option
— Programmable prescaler
— Input capture capability with programmable trigger edge on input pin
— Output compare with programmable mode for the output pin
— Free run and restart modes
— Maskable interrupts on input capture or output compare
— DMA trigger capability on input capture or output compare
Four-channel general purpose timers
•
•
— 16-bit architecture
— Programmable prescaler
— Output pulse widths variable from microseconds to seconds
— Single 16-bit input pulse accumulator
— Toggle-on-overflow feature for pulse-width modulator (PWM) generation
— One dual-mode pulse accumulation channel
Pulse-width modulation timer
— Operates as eight channels with 8-bit resolution or four channels with 16-bit resolution
— Programmable period and duty cycle
— Programmable enable/disable for each channel
— Software selectable polarity for each channel
— Period and duty cycle are double buffered. Change takes effect when the end of the current period is reached
(PWM counter reaches zero) or when the channel is disabled.
— Programmable center or left aligned outputs on individual channels
— Four clock sources (A, B, SA, and SB) provide for a wide range of frequencies
— Emergency shutdown
•
Real-Time Clock (RTC)
— Maintains system time-of-day clock
— Provides stopwatch and alarm interrupt functions
•
•
•
Two periodic interrupt timers (PITs)
— 16-bit counter
— Selectable as free running or count down
Software watchdog timer
— 32-bit counter
— Low power mode support
Clock Generation Features
— Up to 48 MHz crystal input
— On-chip PLL can generate core frequencies up to maximum 60 MHz operating frequency
— Provides clock for integrated EPHY
•
Dual Interrupt Controllers (INTC0/INTC1)
— Support for multiple interrupt sources organized as follows:
–
–
–
Fully-programmable interrupt sources for each peripheral
7 fixed-level interrupt sources
Seven external interrupt signals
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
7
MCF52235 Family Configurations
— Unique vector number for each interrupt source
— Ability to mask any individual interrupt source or all interrupt sources (global mask-all)
— Support for hardware and software interrupt acknowledge (IACK) cycles
— Combinatorial path to provide wake-up from low power modes
DMA controller
•
— Four fully programmable channels
— Dual-address transfer support with 8-, 16-, and 32-bit data capability, along with support for 16-byte (4 x 32-bit)
burst transfers
— Source/destination address pointers that can increment or remain constant
— 24-bit byte transfer counter per channel
— Auto-alignment transfers supported for efficient block movement
— Bursting and cycle steal support
— Software-programmable DMA requesters for the UARTs (3) and 32-bit timers (4)
Reset
•
— Separate reset in and reset out signals
— Seven sources of reset:
–
–
–
–
–
–
–
Power-on reset (POR)
External
Software
Watchdog
Loss of clock
Loss of lock
Low-voltage detection (LVD)
— Status flag indication of source of last reset
Chip integration module (CIM)
•
•
— System configuration during reset
— Selects one of three clock modes
— Configures output pad drive strength
— Unique part identification number and part revision number
General purpose I/O interface
— Up to 56 bits of general purpose I/O
— Bit manipulation supported via set/clear functions
— Programmable drive strengths
— Unused peripheral pins may be used as extra GPIO
JTAG support for system level board testing
•
1.2.2
V2 Core Overview
The version 2 ColdFire processor core is comprised of two separate pipelines decoupled by an instruction buffer. The two-stage
instruction fetch pipeline (IFP) is responsible for instruction-address generation and instruction fetch. The instruction buffer is
a first-in-first-out (FIFO) buffer that holds prefetched instructions awaiting execution in the operand execution pipeline (OEP).
The OEP includes two pipeline stages. The first stage decodes instructions and selects operands (DSOC); the second stage
(AGEX) performs instruction execution and calculates operand effective addresses, if needed.
The V2 core implements the ColdFire instruction set architecture revision A+ with added support for a separate user stack
pointer register and four new instructions to assist in bit processing. Additionally, the MCF52235 core includes the enhanced
multiply-accumulate (EMAC) unit for improved signal processing capabilities. The EMAC implements a three-stage arithmetic
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
8
Freescale Semiconductor
MCF52235 Family Configurations
pipeline, optimized for 16×16 bit operations, with support for one 32-bit accumulator. Supported operands include 16- and
32-bit signed and unsigned integers, signed fractional operands, and a complete set of instructions to process these data types.
The EMAC provides support for execution of DSP operations within the context of a single processor at a minimal hardware
cost.
1.2.3
Integrated Debug Module
The ColdFire processor core debug interface is provided to support system debugging in conjunction with low-cost debug and
emulator development tools. Through a standard debug interface, access debug information and real-time tracing capability is
provided on 112-and 121-lead packages. This allows the processor and system to be debugged at full speed without the need
for costly in-circuit emulators.
The on-chip breakpoint resources include a total of nine programmable 32-bit registers: an address and an address mask register,
a data and a data mask register, four PC registers, and one PC mask register. These registers can be accessed through the
dedicated debug serial communication channel or from the processor’s supervisor mode programming model. The breakpoint
registers can be configured to generate triggers by combining the address, data, and PC conditions in a variety of single- or
dual-level definitions. The trigger event can be programmed to generate a processor halt or initiate a debug interrupt exception.
The MCF52235 implements revision B+ of the ColdFire Debug Architecture.
The MCF52235’s interrupt servicing options during emulator mode allow real-time critical interrupt service routines to be
serviced while processing a debug interrupt event, thereby ensuring that the system continues to operate even during debugging.
To support program trace, the V2 debug module provides processor status (PST[3:0]) and debug data (DDATA[3:0]) ports.
These buses and the PSTCLK output provide execution status, captured operand data, and branch target addresses defining
processor activity at the CPU’s clock rate. The MCF52235 includes a new debug signal, ALLPST. This signal is the logical
AND of the processor status (PST[3:0]) signals and is useful for detecting when the processor is in a halted state (PST[3:0] =
1111).
The full debug/trace interface is available only on the 112 and 121-pin packages. However, every product features the dedicated
debug serial communication channel (DSI, DSO, DSCLK) and the ALLPST signal.
1.2.4
JTAG
The MCF52235 supports circuit board test strategies based on the Test Technology Committee of IEEE and the Joint Test Action
Group (JTAG). The test logic includes a test access port (TAP) consisting of a 16-state controller, an instruction register, and
three test registers (a 1-bit bypass register, a 256-bit boundary-scan register, and a 32-bit ID register). The boundary scan register
links the device’s pins into one shift register. Test logic, implemented using static logic design, is independent of the device
system logic.
The MCF52235 implementation can do the following:
•
•
•
•
•
Perform boundary-scan operations to test circuit board electrical continuity
Sample MCF52235 system pins during operation and transparently shift out the result in the boundary scan register
Bypass the MCF52235 for a given circuit board test by effectively reducing the boundary-scan register to a single bit
Disable the output drive to pins during circuit-board testing
Drive output pins to stable levels
1.2.5
On-Chip Memories
1.2.5.1
SRAM
The dual-ported SRAM module provides a general-purpose 16- or 32-Kbyte memory block that the ColdFire core can access
in a single cycle. The location of the memory block can be set to any 16- or 32-Kbyte boundary within the 4-Gbyte address
space. This memory is ideal for storing critical code or data structures and for use as the system stack. Because the SRAM
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
9
MCF52235 Family Configurations
module is physically connected to the processor's high-speed local bus, it can quickly service core-initiated accesses or
memory-referencing commands from the debug module.
The SRAM module is also accessible by the DMA. The dual-ported nature of the SRAM makes it ideal for implementing
applications with double-buffer schemes, where the processor and a DMA device operate in alternate regions of the SRAM to
maximize system performance.
1.2.5.2
Flash
The ColdFire flash module (CFM) is a non-volatile memory (NVM) module that connects to the processor’s high-speed local
bus. The CFM is constructed with four banks of 32 K×16-bit flash arrays to generate 256 Kbytes of 32-bit flash memory. These
arrays serve as electrically erasable and programmable, non-volatile program and data memory. The flash memory is ideal for
program and data storage for single-chip applications, allowing for field reprogramming without requiring an external high
voltage source. The CFM interfaces to the ColdFire core through an optimized read-only memory controller which supports
interleaved accesses from the 2-cycle flash arrays. A backdoor mapping of the flash memory is used for all program, erase, and
verify operations, as well as providing a read datapath for the DMA. Flash memory may also be programmed via the EzPort,
which is a serial flash programming interface that allows the flash to be read, erased and programmed by an external controller
in a format compatible with most SPI bus flash memory chips. This allows easy device programming via Automated Test
Equipment or bulk programming tools.
1.2.6
Cryptography Acceleration Unit
The MCF52235 device incorporates two hardware accelerators for cryptographic functions. First, the CAU is a coprocessor
tightly-coupled to the V2 ColdFire core that implements a set of specialized operations to increase the throughput of
software-based encryption and message digest functions, specifically the DES, 3DES, AES, MD5 and SHA-1 algorithms.
Second, a random number generator provides FIPS-140 compliant 32-bit values to security processing routines. Both modules
supply critical acceleration to software-based cryptographic algorithms at a minimal hardware cost.
1.2.7
Power Management
The MCF52235 incorporates several low-power modes of operation which are entered under program control and exited by
several external trigger events. An integrated power-on reset (POR) circuit monitors the input supply and forces an MCU reset
as the supply voltage rises. The low voltage detector (LVD) monitors the supply voltage and is configurable to force a reset or
interrupt condition if it falls below the LVD trip point.
1.2.8
FlexCAN
The FlexCAN module is a communication controller implementing version 2.0 of the CAN protocol parts A and B. The CAN
protocol can be used as an industrial control serial data bus, meeting the specific requirements of reliable operation in a harsh
EMI environment with high bandwidth. This instantiation of FlexCAN has 16 message buffers.
1.2.9
UARTs
The MCF52235 has three full-duplex UARTs that function independently. The three UARTs can be clocked by the system bus
clock, eliminating the need for an external clock source. On smaller packages, the third UART is multiplexed with other digital
I/O functions.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
10
Freescale Semiconductor
MCF52235 Family Configurations
1.2.10 I2C Bus
The I2C bus is a two-wire, bidirectional serial bus that provides a simple, efficient method of data exchange and minimizes the
interconnection between devices. This bus is suitable for applications requiring occasional communications over a short
distance between many devices on a circuit board.
1.2.11 QSPI
The queued serial peripheral interface (QSPI) provides a synchronous serial peripheral interface with queued transfer capability.
It allows up to 16 transfers to be queued at once, minimizing the need for CPU intervention between transfers.
1.2.12 Fast ADC
The Fast ADC consists of an eight-channel input select multiplexer and two independent sample and hold (S/H) circuits feeding
separate 10- or 12-bit ADCs. The two separate converters store their results in accessible buffers for further processing.
The ADC can be configured to perform a single scan and halt, perform a scan whenever triggered, or perform a programmed
scan sequence repeatedly until manually stopped.
The ADC can be configured for sequential or simultaneous conversion. When configured for sequential conversions, up to eight
channels can be sampled and stored in any order specified by the channel list register. Both ADCs may be required during a
scan, depending on the inputs to be sampled.
During a simultaneous conversion, both S/H circuits are used to capture two different channels at the same time. This
configuration requires that a single channel may not be sampled by both S/H circuits simultaneously.
Optional interrupts can be generated at the end of the scan sequence if a channel is out of range (measures below the low
threshold limit or above the high threshold limit set in the limit registers) or at several different zero crossing conditions.
1.2.13 DMA Timers (DTIM0–DTIM3)
There are four independent, DMA transfer capable 32-bit timers (DTIM0, DTIM1, DTIM2, and DTIM3) on the each device.
Each module incorporates a 32-bit timer with a separate register set for configuration and control. The timers can be configured
to operate from the system clock or from an external clock source using one of the DTINx signals. If the system clock is selected,
it can be divided by 16 or 1. The input clock is further divided by a user-programmable 8-bit prescaler which clocks the actual
timer counter register (TCRn). Each of these timers can be configured for input capture or reference (output) compare mode.
Timer events may optionally cause interrupt requests or DMA transfers.
1.2.14 General Purpose Timer (GPT)
The general purpose timer (GPT) is a 4-channel timer module consisting of a 16-bit programmable counter driven by a 7-stage
programmable prescaler. Each of the four channels can be configured for input capture or output compare. Additionally, one of
the channels, channel 3, can be configured as a pulse accumulator.
A timer overflow function allows software to extend the timing capability of the system beyond the 16-bit range of the counter.
The input capture and output compare functions allow simultaneous input waveform measurements and output waveform
generation. The input capture function can capture the time of a selected transition edge. The output compare function can
generate output waveforms and timer software delays. The 16-bit pulse accumulator can operate as a simple event counter or a
gated time accumulator.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
11
MCF52235 Family Configurations
1.2.15 Periodic Interrupt Timers (PIT0 and PIT1)
The two periodic interrupt timers (PIT0 and PIT1) are 16-bit timers that provide interrupts at regular intervals with minimal
processor intervention. Each timer can count down from the value written in its PIT modulus register or can be a free-running
down-counter.
1.2.16 Pulse Width Modulation (PWM) Timers
The MCF52235 has an 8-channel, 8-bit PWM timer. Each channel has a programmable period and duty cycle as well as a
dedicated counter. Each of the modulators can create independent continuous waveforms with software-selectable duty rates
from 0 to 100%. The PWM outputs have programmable polarity and can be programmed as left-aligned outputs or
center-aligned outputs. For higher period and duty cycle resolution, each pair of adjacent channels ([7:6], [5:4], [3:2], and [1:0])
can be concatenated to form a single 16-bit channel. The module can, therefore, be configured to support 8/0, 6/1, 4/2, 2/3, or
0/4 8-/16-bit channels.
1.2.17 Software Watchdog Timer
The watchdog timer is a 32-bit timer that facilitates recovery from runaway code. The watchdog counter is a free-running
down-counter that generates a reset on underflow. To prevent a reset, software must periodically restart the countdown.
1.2.18 Phase Locked Loop (PLL)
The clock module contains a crystal oscillator, 8 MHz on-chip relaxation oscillator (OCO), phase-locked loop (PLL), reduced
frequency divider (RFD), low-power divider status/control registers, and control logic. To improve noise immunity, the PLL,
crystal oscillator, and relaxation oscillator have their own power supply inputs: VDDPLL and VSSPLL. All other circuits are
powered by the normal supply pins, VDD and VSS.
1.2.19 Interrupt Controller (INTC0/INTC1)
There are two interrupt controllers on the MCF52235. These interrupt controllers are organized as seven levels with up to nine
interrupt sources per level. Each interrupt source has a unique interrupt vector, and provide each peripheral with all necessary
interrupts. Each internal interrupt has a programmable level [1-7] and priority within the level. The seven external interrupts
have fixed levels/priorities.
1.2.20 DMA Controller
The direct memory access (DMA) controller provides an efficient way to move blocks of data with minimal processor
intervention. It has four channels that allow byte, word, longword, or 16-byte burst line transfers. These transfers are triggered
by software explicitly setting a DCRn[START] bit or by the occurrence of certain UART or DMA timer events.
1.2.21 Reset
The reset controller determines the source of reset, asserts the appropriate reset signals to the system, and keeps track of what
caused the last reset. There are seven sources of reset:
•
•
•
•
•
•
External reset input
Power-on reset (POR)
Watchdog timer
Phase locked-loop (PLL) loss of lock
PLL loss of clock
Software
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
12
Freescale Semiconductor
MCF52235 Family Configurations
•
Low-voltage detector (LVD)
Control of the LVD and its associated reset and interrupt are managed by the reset controller. Other registers provide status flags
indicating the last source of reset and a control bit for software assertion of the RSTO pin.
1.2.22 GPIO
Nearly all pins on the MCF52235 have general purpose I/O capability in addition to their primary functions and are grouped
into 8-bit ports. Some ports do not utilize all 8 bits. Each port has registers that configure, monitor, and control the port pins.
1.2.23 Part Numbers and Packaging
Table 2. Orderable Part Number Summary
Freescale Part
Number
Speed Flash/SRAM
Temp range
Description
Package
(MHz)
(Kbytes)
(°C)
MCF52230CAF60
MCF52230CAL60
MCF52231CAF60
MCF52231CAL60
MCF52232CAF50
MCF52232AF50
MCF52230 Microcontroller
MCF52230 Microcontroller
60
60
60
60
50
50
60
60
60
60
60
60
60
60
60
50
50
50
128 / 32
128 / 32
128 / 32
128 / 32
128 / 32
128 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
256 / 32
80 LQFP
112 LQFP
80 LQFP
112 LQFP
80 LQFP
80 LQFP
80 LQFP
112 LQFP
112 LQFP
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
0 to +70
MCF52231 Microcontroller, FlexCAN
MCF52231 Microcontroller, FlexCAN
MCF52232 Microcontroller
MCF52232 Microcontroller
MCF52233CAF60
MCF52233CAL60
MCF52233CAL60A
MCF52233CVM60
MCF52234CAL60
MCF52234CVM60
MCF52233 Microcontroller
-40 to +85
-40 to +85
-40 to +85
MCF52233 Microcontroller
MCF52233 Microcontroller
MCF52233 Microcontroller
121 MAPBGA -40 to +85
112 LQFP -40 to +85
121 MAPBGA -40 to +85
MCF52234 Microcontroller, FlexCAN
MCF52234 Microcontroller, FlexCAN
MCF52235CAL60 MCF52235 Microcontroller, FlexCAN, CAU, RNGA
MCF52235CAL60A MCF52235 Microcontroller, FlexCAN, CAU, RNGA
MCF52235CVM60 MCF52235 Microcontroller, FlexCAN, CAU, RNGA
112 LQFP
112 LQFP
-40 to +85
-40 to +85
121 MAPBGA -40 to +85
MCF52236CAF50
MCF52236AF50
MCF52236AF50A
MCF52236 Microcontroller
MCF52236 Microcontroller
MCF52236 Microcontroller
80 LQFP
80 LQFP
80 LQFP
-40 to +85
0 to +70
0 to +70
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
13
MCF52235 Family Configurations
1.2.24 Package Pinouts
Figure 2 shows the pinout configuration for the 80-pin LQFP.
TCLK/PSTCLK
TMS/BKPT
RCON/EZPCS
TDI/DSI
TDO/DSO
TRST/DSCLK
ALLPST
DTIN0/DTOUT0
DTIN1/DTOUT1
VDDX1
ACTLED
LNKLED
VDDR
SPDLED
1
2
3
4
5
6
7
8
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
PHY_VSSRX
PHY_VDDRX
PHY_RXN
PHY_RXP
PHY_VSSTX
PHY_TXN
PHY_TXP
PHY_VDDTX
PHY_VDDA
PHY_VSSA
PHY_RBIAS
VDD2
9
10
11
12
13
14
15
16
17
18
19
20
80-pin
LQFP
VSSX1
JTAG_EN
DTIN2/DTOUT2
DTIN3/DTOUT3
URTS1
UCTS1
URTS0
UCTS0
SYNCB
VSS2
DUPLED
COLLED
IRQ11
SYNCA
Figure 2. 80-pin LQFP Pin Assignments
Figure 3 shows the pinout configuration for the 112-pin LQFP.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
14
Freescale Semiconductor
MCF52235 Family Configurations
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
1
2
3
4
5
6
7
8
ACTLED
LNKLED
VDDR
SPDLED
PST3
PST2
PST1
TCLK/PSTCLK
TMS/BKPT
RCON/EZPCS
TDI/DSI
TDO/DSO
TRST/DSCLK
ALLPST
DTIN0/DTOUT0
DTIN1/DTOUT1
IRQ8
PST0
9
PHY_VSSRX
PHY_VDDRX
PHY_RXN
PHY_RXP
PHY_VSSTX
PHY_TXN
PHY_TXP
PHY_VDDTX
PHY_VDDA
PHY_VSSA
PHY_RBIAS
VDD2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
IRQ9
DDATA3
DDATA2
VDDX1
VSSX1
DDATA1
DDATA0
JTAG_EN
IRQ6
112-pin LQFP
IRQ5
VSS2
UTXD2
URXD2
UCTS2
DTIN2/DTOUT2
DTIN3/DTOUT3
URTS1
UCTS1
URTS0
UCTS0
SYNCB
URTS2
DUPLED
COLLED
IRQ11
SYNCA
Figure 3. 112-pin LQFP Pin Assignments
Figure 4 shows the pinout configuration for the 121 MAPBGA.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
15
1
2
3
4
5
6
7
8
9
10
11
TCLK
SDA
SCL
IRQ15
IRQ14
IRQ13
VSSA
VDDA
AN1
AN7
AN5
A
B
C
D
E
F
G
H
J
TMS
TRST
RCON
TDO
GPT0
TDI
GPT3
GPT2
PWM5
PWM7
VDDX
PWM1
PWM3
VDDX
VDDX
VSS
VRL
IRQ12
VDD
VRH
AN0
AN2
AN3
AN6
LNKLED
PST3
AN4
ACTLED
SPDLED
PHY_RXN
DTIN1
DDATA3
DDATA0
DTIN2
DTIN3
SYNCB
SYNCA
IRQ10
DTIN0
IRQ9
ALLPST
IRQ8
GPT1
VDDR
VDD
VSS
PST2
PST0
VSS
VSS
VSS
PST1
DDATA1
IRQ5
DDATA2
IRQ6
VSS
VSS
VSS
PHY_VSSRX PHY_VDDRX PHY_RXP
JTAG_EN
QSPI_DIN
VDDX
VDDX
VDDX
RSTI
VDDX
TEST
XTAL
PHY_VSSA PHY_VSSTX PHY_VDDTX PHY_TXP
URTS0
UCTS0
URXD0
UTXD0
URTS1
UCTS1
URXD1
UTXD1
QSPI_CS1
TXLED
IRQ1
IRQ2
IRQ3
RXLED
COLLED
IRQ11
PHY_VDDA
DUPLED
URTS2
PHY_TXN
PHY_RBIAS
URXD2
QSPI_DOUT QSPI_CS2
QSPI_CLK
QSPI_CS0
QSPI_CS3
IRQ4
VDDPLL
RSTO
VSSPLL
EXTAL
K
L
IRQ7
UCTS2
UTXD2
Figure 4. 121 MAPBGA Pin Assignments
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
Table 3. Pin Functions by Primary and Alternate Purpose
Drive
Primary
Function
SecondaryF
unction
Tertiary
Quaternary
Function
Wired OR
Control
Pull-up/
Pin on 121
MAPBGA
Pin on 112 Pin on 80
Pin Group
Strength/
Function
Pull-down2
LQFP
LQFP
Control1
ADC3
AN7
AN6
—
—
PAN[7]
PAN[6]
PAN[5]
PAN[4]
PAN[3]
PAN[2]
PAN[1]
PAN[0]
PAS[3]
PAS[2]
—
Low
Low
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
A10
B10
A11
B11
C9
B9
A9
C8
K1
J1
88
87
86
85
89
90
91
92
28
27
93
96
94
95
48
49
45
47
7
64
63
62
61
65
66
67
68
20
19
69
72
70
71
36
37
33
35
7
—
—
AN5
—
—
Low
—
AN4
—
—
Low
—
AN3
—
—
Low
—
AN2
—
—
Low
—
AN1
—
—
Low
—
AN0
—
—
Low
—
SYNCA
SYNCB
VDDA
VSSA
VRH
CANTX4
FEC_MDIO
PDSR[39]
PDSR[39]
N/A
—
CANRX4
FEC_MDC
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
—
A8
A7
B8
B7
L7
—
N/A
—
N/A
VRL
—
N/A
Clock
Generation
EXTAL
—
N/A
XTAL
—
N/A
J7
VDDPLL5
VSSPLL
ALLPST
DDATA[3:0]
PST[3:0]
—
N/A
K6
K7
D3
—
N/A
Debug
Data
—
High
High
High
PDD[7:4]
PDD[3:0]
—
E1, F3,F2, F1 12,13,16,17
—
—
—
D10, D9,
E10, E9
80,79,78,77
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Drive
Primary
Function
SecondaryF
unction
Tertiary
Quaternary
Function
Wired OR
Control
Pull-up/
Pin on 121
MAPBGA
Pin on 112 Pin on 80
Pin Group
Strength/
Function
Pull-down2
LQFP
LQFP
Control1
Ethernet
LEDs
ACTLED
COLLED
DUPLED
LNKLED
SPDLED
RXLED
—
—
—
—
PLD[0]
PLD[4]
PLD[3]
PLD[1]
PLD[2]
PLD[5]
PLD[6]
—
PDSR[32] PWOR[8]
PDSR[36] PWOR[12]
PDSR[35] PWOR[11]
PDSR[33] PWOR[9]
PDSR[34] PWOR[10]
PDSR[37] PWOR[13]
PDSR[38] PWOR[14]
—
—
—
—
—
—
—
—
C11
J9
84
58
59
83
81
52
51
82
66
74
73
71
70
68
75
69
67
76
72
111
112
106
105
98
97
60
42
43
59
57
—
—
58
46
54
53
51
50
48
55
49
47
56
52
79
80
—
—
—
—
—
—
J10
C10
D11
H9
—
—
—
—
—
—
TXLED
—
—
H8
VDDR
—
—
—
—
—
—
—
—
—
—
D8
Ethernet
PHY
PHY_RBIAS
PHY_RXN
PHY_RXP
PHY_TXN
PHY_TXP
PHY_VDDA5
PHY_VDDRX5
PHY_VDDTX5
PHY_VSSA
PHY_VSSRX
PHY_VSSTX
SCL
—
—
—
J11
E11
F11
H11
G11
H10
F10
G10
G8
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
N/A
N/A
N/A
N/A
N/A
N/A
—
—
—
—
—
—
—
—
—
—
—
—
—
F9
—
—
—
G9
I2C
CANTX4
CANRX4
—
UTXD2
URXD2
—
PAS[0]
PAS[1]
PGP[7]
PGP[6]
PGP[5]
PGP[4]
PDSR[0]
PDSR[0]
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
A3
SDA
—
A2
Interrupts3
IRQ15
PSDR[47]
PSDR[46]
PSDR[45]
PSDR[44]
—
A4
IRQ14
—
—
—
A5
IRQ13
—
—
—
A6
IRQ12
—
—
—
C7
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Drive
Primary
Function
SecondaryF
unction
Tertiary
Quaternary
Function
Wired OR
Control
Pull-up/
Pin on 121
MAPBGA
Pin on 112 Pin on 80
Pin Group
Strength/
Function
Pull-down2
LQFP
LQFP
Control1
Continued
Interrupts3
IRQ11
IRQ10
IRQ9
—
—
PGP[3]
PGP[2]
PGP[1]
PGP[0]
PNQ[7]
PNQ[6]
PNQ[5]
PNQ[4]
PNQ[3]
PNQ[2]
PNQ[1]
—
PSDR[43]
PSDR[42]
PSDR[41]
PSDR[40]
Low
—
—
—
—
—
—
—
—
—
—
—
N/A
—
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up
K9
L1
E2
E3
L9
G3
G2
L5
L8
K8
J8
57
29
11
10
56
19
20
41
53
54
55
18
1
41
—
—
—
40
—
—
29
—
—
39
12
1
—
—
—
—
IRQ8
—
—
—
IRQ7
—
—
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Up6
Pull-Down
Pull-Up7
IRQ6
FEC_RXER
FEC_RXD[1]
—
Low
IRQ5
—
Low
IRQ4
—
Low
IRQ3
—
FEC_RXD[2]
FEC_RXD[3]
PWM1
Low
IRQ2
—
Low
IRQ1
SYNCA
—
High
JTAG/BDM
JTAG_EN
—
N/A
G4
A1
TCLK/
CLKOUT
—
—
High
PSTCLK
TDI/DSI
TDO/DSO
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
N/A
High
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Pull-Up7
—
C3
C2
B1
C1
B2
4
5
2
6
3
4
5
2
6
3
TMS/BKPT
TRST/DSCLK
RCON/EZPCS
Pull-Up7
Pull-Up
Pull-Up
Mode
Selection
PWM
PWM7
PWM5
PWM3
PWM1
—
—
—
—
—
—
—
—
PTD[3]
PTD[2]
PTD[1]
PTD[0]
PDSR[31]
PDSR[30]
PDSR[29]
PDSR[28]
—
—
—
—
—
—
—
—
C5
B5
C6
B6
104
103
100
99
—
—
—
—
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Drive
Primary
Function
SecondaryF
unction
Tertiary
Quaternary
Function
Wired OR
Control
Pull-up/
Pin on 121
MAPBGA
Pin on 112 Pin on 80
Pin Group
Strength/
Function
Pull-down2
LQFP
LQFP
Control1
QSPI3
QSPI_DIN/
EZPD
CANRX4
CANTX4
SCL
URXD1
UTXD1
URTS1
PQS[1]
PQS[0]
PQS[2]
PDSR[2]
PDSR[1]
PDSR[3]
PWOR[4]
PWOR[5]
PWOR[6]
—
—
H4
J4
34
25
QSPI_DOUT/E
ZPQ
35
36
26
27
QSPI_CLK/
EZPCK
Pull-Up8
K4
QSPI_CS3
QSPI_CS2
QSPI_CS1
QSPI_CS0
RSTI
SYNCA
—
SYNCB
FEC_TXCLK
FEC_TXEN
UCTS1
—
PQS[6]
PQS[5]
PQS[4]
PQS[3]
—
PDSR[7]
PDSR[6]
PDSR[5]
PDSR[4]
N/A
—
—
K5
J5
40
39
38
37
44
46
50
107
108
109
110
22
21
9
—
—
—
28
32
34
38
75
76
77
78
14
13
9
—
—
—
—
—
H5
L4
J6
SDA
PWOR[7]
Pull-Up8
Pull-Up9
—
Reset9
Test
—
N/A
RSTO
—
—
—
high
—
L6
H7
B4
C4
D4
B3
H1
G1
D1
D2
J2
TEST
—
—
—
N/A
N/A
Pull-Down
Pull-Up10
Pull-Up10
Pull-Up10
Pull-Up10
—
Timers,
16-bit3
GPT3
FEC_TXD[3]
FEC_TXD[2]
FEC_TXD[1]
FEC_TXER
DTOUT3
DTOUT2
DTOUT1
DTOUT0
CANRX4
CANTX4
—
PWM7
PTA[3]
PTA[2]
PTA[1]
PTA[0]
PTC[3]
PTC[2]
PTC[1]
PTC[0]
PUA[3]
PUA[2]
PUA[1]
PUA[0]
PDSR[23]
PDSR[22]
PDSR[21]
PDSR[20]
PDSR[19]
PDSR[18]
PDSR[17]
PDSR[16]
PDSR[11]
PDSR[10]
PDSR[9]
PDSR[8]
—
GPT2
PWM5
—
GPT1
PWM3
—
GPT0
PWM1
—
Timers,
32-bit
DTIN3
PWM6
—
DTIN2
PWM4
—
—
DTIN1
PWM2
—
—
—
DTIN0
PWM0
—
8
8
UART 03
UCTS0
URTS0
URXD0
UTXD0
FEC_RXCLK
FEC_RXDV
FEC_RXD[0]
FEC_CRS
—
—
26
25
30
31
18
17
21
22
—
—
H2
K2
L2
PWOR[0]
PWOR[1]
—
—
—
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
Table 3. Pin Functions by Primary and Alternate Purpose (continued)
Drive
Primary
Function
SecondaryF
unction
Tertiary
Quaternary
Function
Wired OR
Control
Pull-up/
Pin on 121
MAPBGA
Pin on 112 Pin on 80
Pin Group
Strength/
Function
Pull-down2
LQFP
LQFP
Control1
UART 13
UCTS1
URTS1
URXD1
UTXD1
UCTS2
URTS2
URXD2
UTXD2
SYNCA
SYNCB
VDD
SYNCA
URXD2
PUB[3]
PUB[2]
PUB[1]
PUB[0]
PUC[3]
PUC[2]
PUC[1]
PUC[0]
PAS[3]
PAS[2]
—
PDSR[15]
PDSR[14]
—
—
—
—
—
—
—
—
—
—
—
—
—
—
J3
H3
24
23
16
15
SYNCB
UTXD2
—
FEC_TXD[0]
PDSR[13] PWOR[2]
PDSR[12] PWOR[3]
K3
32
23
—
FEC_COL
L3
33
24
UART 2
—
—
PDSR[27]
PDSR[26]
PDSR[25]
PDSR[24]
PDSR[39]
PDSR[39]
N/A
—
—
L10
K10
K11
L11
—
61
—
—
—
—
60
—
—
—
62
—
—
—
FEC_MDIO
FEC_MDC
—
—
63
—
FlexCAN
CANTX4
CANRX4
—
—
28
20
—
—
27
19
VDD5,11
VDDX
N/A
N/A
D7, E8
65,102
14, 43
45,74
10, 31
VDDX
—
—
—
N/A
D5, D6, E6, G5,
G6, G7, H6
VSS
VSS
—
—
—
N/A
N/A
—
E4, E5, E7,F4,
F5, F6, F7, F8
64,101
44,73
VSSX
VSSX
—
—
—
N/A
N/A
—
—
15, 42
11, 30
1
The PDSR and PSSR registers are described in Chapter 14, “General Purpose I/O Module. All programmable signals default to 2mA drive in normal
(single-chip) mode.
All signals have a pull-up in GPIO mode.
The use of an external PHY limits ADC, interrupt, and QSPI functionality. It also disables the UART0/1 and timer pins.
2
3
4
5
The multiplexed CANTX and CANRX signals do not have dedicated pins, but are available as muxed replacements for other signals.
The VDD1, VDD2, VDDPLL, and PHY_VDD pins are for decoupling only and should not have power directly applied to them.
6
7
8
9
For primary and GPIO functions only.
Only when JTAG mode is enabled.
For secondary and GPIO functions only.
RSTI has an internal pull-up resistor; however, the use of an external resistor is strongly recommended.
10 For GPIO function. Primary Function has pull-up control within the GPT module.
11 This list for power and ground does not include those dedicated power/ground pins included elsewhere, e.g. in the Ethernet PHY.
Because of an order from the United States International Trade Commission, BGA-packaged product lines and part numbers indicated here currently are not
available from Freescale for import or sale in the United States prior to September 2010:MCF52234CVM60, MCF52235CVM60
MCF52235 Family Configurations
1.3
Reset Signals
Table 4 describes signals that are used to either reset the chip or as a reset indication.
Table 4. Reset Signals
Signal Name
Abbreviation
Function
I/O
Reset In
RSTI
Primary reset input to the device. Asserting RSTI immediately resets
the CPU and peripherals.
I
Reset Out
RSTO
Driven low for 512 CPU clocks after the reset source has deasserted.
O
1.4
PLL and Clock Signals
Table 5 describes signals that are used to support the on-chip clock generation circuitry.
Table 5. PLL and Clock Signals
Signal Name
Abbreviation
Function
I/O
External Clock In
Crystal
EXTAL
XTAL
Crystal oscillator or external clock input.
Crystal oscillator output.
I
O
O
Clock Out
CLKOUT
This output signal reflects the internal system clock.
1.5
Mode Selection
Table 6 describes signals used in mode selection, Table 6 describes particular clocking modes.
Table 6. Mode Selection Signals
Signal Name
Abbreviation
Function
I/O
Reset Configuration
RCON
The Serial Flash Programming mode is entered by asserting the
RCON pin (with the TEST pin negated) as the chip comes out of
reset. During this mode, the EzPort has access to the Flash memory
which can be programmed from an external device.
—
Test
TEST
Reserved for factory testing only and in normal modes of operation
should be connected to VSS to prevent unintentional activation of
test functions.
I
1.6
External Interrupt Signals
Table 7 describes the external interrupt signals.
Table 7. External Interrupt Signals
Signal Name
Abbreviation
Function
I/O
External Interrupts
IRQ[15:1] External interrupt sources.
I
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
22
Freescale Semiconductor
MCF52235 Family Configurations
1.7
Queued Serial Peripheral Interface (QSPI)
Table 8 describes QSPI signals.
Table 8. Queued Serial Peripheral Interface (QSPI) Signals
Signal Name
Abbreviation
Function
I/O
QSPI Synchronous
Serial Output
QSPI_DOUT Provides the serial data from the QSPI and can be programmed to be
driven on the rising or falling edge of QSPI_CLK.
O
QSPI Synchronous
Serial Data Input
QSPI_DIN Provides the serial data to the QSPI and can be programmed to be
sampled on the rising or falling edge of QSPI_CLK.
I
QSPI Serial Clock
QSPI_CLK Provides the serial clock from the QSPI. The polarity and phase of
QSPI_CLK are programmable.
O
O
SynchronousPeripheral QSPI_CS[3:0] QSPI peripheral chip selects that can be programmed to be active
Chip Selects high or low.
1.8
Fast Ethernet Controller EPHY Signals
Table 9 describes the Fast Ethernet Controller (FEC) signals.
Table 9. Fast Ethernet Controller (FEC) Signals
Signal Name
Abbreviation
Function
I/O
Twisted Pair Input +
RXP
Differential Ethernet twisted-pair input pin. This pin is high-impedance
out of reset.
I
Twisted Pair Input -
Twisted Pair Output +
Twisted Pair Output -
Bias Control Resistor
RXN
TXN
Differential Ethernet twisted-pair input pin. This pin is high-impedance
out of reset.
I
Differential Ethernet twisted-pair output pin. This pin is
high-impedance out of reset.
O
O
I
TXP
Differential Ethernet twisted-pair output pin. This pin is
high-impedance out of reset.
RBIAS
Connect a 12.4 kΩ (1.0%) external resistor, RBIAS, between the
PHY_RBIAS pin and analog ground.
Place this resistor as near to the chip pin as possible. Stray
capacitance must be kept to less than 10 pF
(>50 pF causes instability). No high-speed signals can be permitted in
the region of RBIAS.
Activity LED
Link LED
ACT_LED
Indicates when the EPHY is transmitting or receiving
O
O
O
O
O
O
O
LINK_LED Indicates when the EPHY has a valid link
SPD_LED Indicates the speed of the EPHY connection
Speed LED
Duplex LED
Collision LED
Transmit LED
Receive LED
DUPLED
COLLED
TXLED
Indicates the duplex (full or half) of the EPHY connection
Indicates if the EPHY detects a collision
Indicates if the EPHY is transmitting
RXLED
Indicates if the EPHY is receiving
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
23
MCF52235 Family Configurations
2
1.9
I C I/O Signals
2
Table 10 describes the I C serial interface module signals.
2
Table 10. I C I/O Signals
Signal Name
Abbreviation
Function
I/O
Serial Clock
SCL
Open-drain clock signal for the for the I2C interface. Either it is driven
by the I2C module when the bus is in master mode or it becomes the
clock input when the I2C is in slave mode.
I/O
Serial Data
SDA
Open-drain signal that serves as the data input/output for the I2C
interface.
I/O
1.10 UART Module Signals
Table 11 describes the UART module signals.
Table 11. UART Module Signals
Function
Signal Name
Abbreviation
I/O
Transmit Serial Data
Output
UTXDn
Transmitter serial data outputs for the UART modules. The output is
held high (mark condition) when the transmitter is disabled, idle, or in
the local loopback mode. Data is shifted out, LSB first, on this pin at
the falling edge of the serial clock source.
O
Receive Serial Data
Input
URXDn
Receiver serial data inputs for the UART modules. Data is received on
this pin LSB first. When the UART clock is stopped for power-down
mode, any transition on this pin restarts it.
I
Clear-to-Send
UCTSn
URTSn
Indicate to the UART modules that they can begin data transmission.
I
Request-to-Send
Automatic request-to-send outputs from the UART modules. This
signal can also be configured to be asserted and negated as a
function of the RxFIFO level.
O
1.11 DMA Timer Signals
Table 12 describes the signals of the four DMA timer modules.
Table 12. DMA Timer Signals
Signal Name
Abbreviation
Function
I/O
DMA Timer Input
DTINn
Event input to the DMA timer modules.
I
DMA Timer Output
DTOUTn
Programmable output from the DMA timer modules.
O
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
24
Freescale Semiconductor
MCF52235 Family Configurations
1.12 ADC Signals
Table 13 describes the signals of the Analog-to-Digital Converter.
Table 13. ADC Signals
Function
Signal Name
Abbreviation
I/O
Analog Inputs
AN[7:0]
VRH
Inputs to the A-to-D converter.
I
I
I
Analog Reference
Reference voltage high and low inputs.
VRL
Analog Supply
VDDA
VSSA
Isolate the ADC circuitry from power supply noise
—
—
1.13 General Purpose Timer Signals
Table 14 describes the General Purpose Timer Signals.
Table 14. GPT Signals
Function
Inputs to or outputs from the general purppose timer module
Signal Name
Abbreviation
I/O
General Purpose Timer
Input/Output
GPT[3:0]
I/O
1.14 Pulse Width Modulator Signals
Table 15 describes the PWM signals.
Table 15. PWM Signals
Function
PWM[7:0] Pulse width modulated output for PWM channels
Signal Name
Abbreviation
I/O
PWM Output Channels
O
1.15 Debug Support Signals
These signals are used as the interface to the on-chip JTAG controller and also to interface to the BDM logic.
Table 16. Debug Support Signals
Signal Name
Abbreviation
Function
I/O
JTAG Enable
Test Reset
JTAG_EN
TRST
Select between debug module and JTAG signals at reset
I
I
This active-low signal is used to initialize the JTAG logic
asynchronously.
Test Clock
TCLK
TMS
Used to synchronize the JTAG logic.
I
I
Test Mode Select
Used to sequence the JTAG state machine. TMS is sampled on the
rising edge of TCLK.
Test Data Input
TDI
Serial input for test instructions and data. TDI is sampled on the rising
edge of TCLK.
I
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
25
MCF52235 Family Configurations
Table 16. Debug Support Signals (continued)
Function
Signal Name
Abbreviation
TDO
I/O
Test Data Output
Serial output for test instructions and data. TDO is tri-stateable and is
actively driven in the shift-IR and shift-DR controller states. TDO
changes on the falling edge of TCLK.
O
Development Serial
Clock
DSCLK
BKPT
Development Serial Clock. Internally synchronized input. (The logic
level on DSCLK is validated if it has the same value on two
consecutive rising bus clock edges.) Clocks the serial communication
port to the debug module during packet transfers. Maximum frequency
is PSTCLK/5. At the synchronized rising edge of DSCLK, the data
input on DSI is sampled and DSO changes state.
I
I
Breakpoint
Breakpoint. Input used to request a manual breakpoint. Assertion of
BKPT puts the processor into a halted state after the current
instruction completes. Halt status is reflected on processor status
signals (PST[3:0]) as the value 0xF. If CSR[BKD] is set (disabling
normal BKPT functionality), asserting BKPT generates a debug
interrupt exception in the processor.
Development Serial
Input
DSI
Development Serial Input. Internally synchronized input that provides
data input for the serial communication port to the debug module after
the DSCLK has been seen as high (logic 1).
I
Development Serial
Output
DSO
Development Serial Output. Provides serial output communication for
debug module responses. DSO is registered internally. The output is
delayed from the validation of DSCLK high.
O
O
O
Debug Data
DDATA[3:0] Display captured processor data and breakpoint status. The CLKOUT
signal can be used by the development system to know when to
sample DDATA[3:0].
Processor Status Clock
PSTCLK
Processor Status Clock. Delayed version of the processor clock. Its
rising edge appears in the center of valid PST and DDATA output.
PSTCLK indicates when the development system should sample PST
and DDATA values.
If real-time trace is not used, setting CSR[PCD] keeps PSTCLK, PST,
and DDATA outputs from toggling without disabling triggers.
Non-quiescent operation can be re-enabled by clearing CSR[PCD],
although the external development systems must resynchronize with
the PST and DDATA outputs.
PSTCLK starts clocking only when the first non-zero PST value (0xC,
0xD, or 0xF) occurs during system reset exception processing.
Processor Status
Outputs
PST[3:0]
ALLPST
Indicate core status. Debug mode timing is synchronous with the
processor clock; status is unrelated to the current bus transfer. The
CLKOUT signal can be used by the development system to know
when to sample PST[3:0].
O
O
All Processor Status
Outputs
Logical AND of PST[3:0]
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
26
Freescale Semiconductor
MCF52235 Family Configurations
1.16 EzPort Signal Descriptions
Table 17 contains a list of EzPort external signals
Table 17. EzPort Signal Descriptions
Abbreviation Function
EZPCK Shift clock for EzPort transfers
Signal Name
I/O
EzPort Clock
I
EzPort Chip Select
EZPCS
EZPD
EZPQ
Chip select for signalling the start and end
of serial transfers
I
EzPort Serial Data In
EzPort Serial Data Out
EZPD is sampled on the rising edge of
EZPCK
I
EZPQ transitions on the falling edge of
EZPCK
O
1.17 Power and Ground Pins
The pins described in Table 18 provide system power and ground to the chip. Multiple pins are provided for adequate current
capability. All power supply pins must have adequate bypass capacitance for high-frequency noise suppression.
Table 18. Power and Ground Pins
Signal Name
Abbreviation
Function
I/O
PLL Analog Supply
VDDPLL,
VSSPLL
Dedicated power supply signals to isolate the sensitive PLL analog
circuitry from the normal levels of noise present on the digital power
supply.
I
Positive Supply
Ground
VDD
VSS
These pins supply positive power to the core logic.
This pin is the negative supply (ground) to the chip.
I
—
Some of the V and V pins on the device are only to be used for noise bypass. Figure 5 shows a typical connection diagram.
DD
SS
Pay particular attention to those pins which show only capacitor connections. Do not connect power supply voltage directly to
these pins.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
27
Electrical Characteristics
33
35
69
70
71
72
58
11
10
31
30
45
44
74
73
VDDPLL
0.22µF
0.1µF
1000pF
V
SSPLL
VDDA
VRH
10µF
10V
Tantalum
0.1µF
10µH
*
VRL
VSSA
VDDR
VSSX1
VDDX1
VDDX2
VSSX2
VDD2
VSS2
VDD1
VSS1
0.1µF
0.1µF
3.3V
MCF52235
0.1µF
Pin numbering is shown
for the 80-pin LQFP
0.22µF
0.22µF
0.22µF 0.22µF 0.22µF
12.4KΩ
1%
*
optional
Figure 5. Suggested Connection Scheme for Power and Ground
2
Electrical Characteristics
This section contains electrical specification tables and reference timing diagrams for the MCF52235, including detailed
information on power considerations, DC/AC electrical characteristics, and AC timing specifications.
NOTE
The parameters specified in this appendix supersede any values found in the module
specifications.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
28
Freescale Semiconductor
Electrical Characteristics
2.1
Maximum Ratings
1, 2
Table 19. Absolute Maximum Ratings
Rating
Symbol
Value
Unit
Supply voltage
VDD
VDDPLL
VIN
–0.3 to +4.0
–0.3 to +4.0
–0.3 to + 4.0
0 to 3.3
V
V
Clock synthesizer supply voltage
Digital input voltage 3
EXTAL pin voltage
V
VEXTAL
VXTAL
IDD
V
XTAL pin voltage
0 to 3.3
V
Instantaneous maximum current
25
mA
Single pin limit (applies to all pins) 4, 5
Operating temperature range (packaged)
TA
(TL - TH)
–40 to 85
°C
°C
Storage temperature range
Tstg
–65 to 150
1
2
Functional operating conditions are given in DC Electrical Specifications. Absolute Maximum
Ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress
beyond those listed may affect device reliability or cause permanent damage to the device.
This device contains circuitry protecting against damage due to high static voltage or electrical
fields; however, it is advised that normal precautions be taken to avoid application of any voltages
higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is
enhanced if unused inputs are tied to an appropriate logic voltage level (e.g., either VSS or VDD).
Input must be current limited to the IDD value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then
use the larger of the two values.
3
4
5
All functional non-supply pins are internally clamped to VSS and VDD
The power supply must maintain regulation within operating VDD range during instantaneous and
operating maximum current conditions. If positive injection current (Vin > VDD) is greater than IDD
.
,
the injection current may flow out of VDD and could result in external power supply going out of
regulation. Ensure external VDD load shunts current greater than maximum injection current. This is
the greatest risk when the MCU is not consuming power (ex; no clock). The power supply must
maintain regulation within operating VDD range during instantaneous and operating maximum
current conditions.
Table 20 lists thermal resistance values.
NOTE
The use of this device in one- or two-layer board designs is not recommended due to the
limited thermal conductance provided by those boards.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
29
Electrical Characteristics
Table 20. Thermal Characteristics
Symbol
Characteristic
Junction to ambient, natural convection
Package1
Value
Unit
θJA
80-pin LQFP, four-layer board
112-pin LQFP, four-layer board
121 MAPBGA, four-layer board
80-pin LQFP, one-layer board1
121 MAPBGA, one-layer board1
112-pin LQFP, one-layer board1
80-pin LQFP, four-layer board
112-pin LQFP, four-layer board
121 MAPBGA, four-layer board
80-pin LQFP, one-layer board1
112-pin LQFP, one-layer board1
121 MAPBGA, one-layer board1
80-pin LQFP
36.02,3
35.0
32
°C/W
49.01
561
44.01
30.0
29.0
28
Junction to ambient (@200 ft/min)
θJMA
°C/W
39.01
35.01
461
Junction to board
θJB
θJC
Ψjt
Tj
22.04
23.0
18
°C/W
°C/W
°C/W
oC
112-pin LQFP
121 MAPBGA, four-layer board
80-pin LQFP
Junction to case
6.05
112-pin LQFP
6.0
121 MAPBGA
10
Junction to top of package, natural convection
Maximum operating junction temperature
80-pin LQFP
2.06
2.06
2.06
130
112-pin LQFP
121 MAPBGA
All
1
The use of this device in one- or two-layer board designs is not recommended due to the limited thermal conductance
provided by those boards.
2
θ
JMA and Ψjt parameters are simulated in conformance with EIA/JESD Standard 51-2 for natural convection. Freescale
recommends the use of θJMA and power dissipation specifications in the system design to prevent device junction
temperatures from exceeding the rated specification. System designers should be aware that device junction temperatures
can be significantly influenced by board layout and surrounding devices. Conformance to the device junction temperature
specification can be verified by physical measurement in the customer’s system using the Ψjt parameter, the device power
dissipation, and the method described in EIA/JESD Standard 51-2.
3
4
Per JEDEC JESD51-6 with the board horizontal.
Thermal resistance between the die and the printed circuit board in conformance with JEDEC JESD51-8. Board
temperature is measured on the top surface of the board near the package.
5
6
Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883
Method 1012.1).
Thermal characterization parameter indicating the temperature difference between package top and the junction
temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written
in conformance with Psi-JT.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
30
Freescale Semiconductor
Electrical Characteristics
The average chip-junction temperature (T ) in °C can be obtained from
J
TJ = TA + (PD × ΘJMA
)
Eqn. 1
where
•
•
•
•
•
T = ambient temperature, °C
A
Θ
= package thermal resistance, junction-to-ambient, °C/W
JMA
P = P
+ P
I/O
D
INT
P
P
= chip internal power, I × V , watts
DD DD
= power dissipation on input and output pins — user determined
INT
I/O
For most applications, PI/O < P
and can be ignored. An approximate relationship between P and T (if P is neglected) is:
INT
D
J
I/O
PD = K ÷ (TJ + 273°C)
Eqn. 2
Eqn. 3
Solving equations 1 and 2 for K gives:
2
K = PD × (TA + 273°C) + ΘJMA × PD
where K is a constant pertaining to the particular part. K can be determined from Equation 3 by measuring P (at equilibrium)
D
for a known T . Using this value of K, the values of P and T can be obtained by solving Equation 1 and Equation 2 iteratively
A
D
J
for any value of T .
A
2.2
ESD Protection
1
Table 21. ESD Protection Characteristics
Characteristic
Symbol
Value
Units
ESD target for Human Body Model
HBM
1500 (ADC and EPHY pins)
2000 (All other pins)
V
ESD target for Charged Device Model
HBM circuit description
CDM
Rseries
C
250
1500
100
V
ohms
pF
Number of pulses per pin (HBM)
positive pulses
negative pulses
—
—
—
1
1
Number of pulses per pin (CDM)
positive pulses
negative pulses
—
—
—
3
3
Interval of pulses (HBM)
Interval of pulses (CDM)
—
—
1.0
0.2
sec
sec
1
A device is defined as a failure if the device no longer meets the device specification requirements after
exposure to ESD pulses. Complete DC parametric and functional testing is performed per applicable device
specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
31
Electrical Characteristics
2.3
DC Electrical Specifications
1
Table 22. DC Electrical Specifications
Characteristic
Symbol
Min
Max
Unit
Supply voltage
VDD
VIH
3.0
0.7 × VDD
VSS – 0.3
0.06 × VDD
2.15
3.6
4.0
V
V
Input high voltage
Input low voltage
VIL
0.35 x VDD
—
V
Input hysteresis
VHYS
VLVD
VLVDHYS
Iin
mV
V
Low-voltage detect trip voltage (VDD falling)
Low-voltage detect hysteresis (VDD rising)
Input leakage current
2.3
60
120
mV
μA
–1.0
1.0
V
in = VDD or VSS, input-only pins
High impedance (off-state) leakage current
IOZ
VOH
VOL
–1.0
VDD - 0.5
__
1.0
__
μA
V
Vin = VDD or VSS, all input/output and output pins
Output high voltage (all input/output and all output pins)
IOH = –2.0 mA
Output low voltage (all input/output and all output pins)
IOL = 2.0 mA
0.5
V
Weak internal pull-up device current, tested at VIL max.2
Input capacitance 3
IAPU
Cin
–10
–130
μA
pF
All input-only pins
All input/output (three-state) pins
—
—
7
7
Load capacitance4
Low drive strength
High drive strength
pF
CL
IIC
25
50
3, 5, 6, 7
DC injection current
mA
VNEGCLAMP =VSS– 0.3 V, VPOSCLAMP = VDD + 0.3
Single pin limit
Total MCU limit, Includes sum of all stressed pins
–1.0
–10
1.0
10
1
Refer to Table 25 for additional PLL specifications.
Refer to Table 3 for pins with internal pull-up devices.
2
3
4
This parameter is characterized before qualification rather than 100% tested.
pF load ratings are based on DC loading and are provided as an indication of driver strength. High speed interfaces
require transmission line analysis to determine proper drive strength and termination.
5
6
All functional non-supply pins are internally clamped to VSS and their respective VDD
.
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values for positive and negative clamp voltages, then use the larger of the two values.
7
The power supply must maintain regulation within operating VDD range during instantaneous and operating maximum
current conditions. If positive injection current (Vin > VDD) is greater than IDD, the injection current may flow out of VDD
and could result in external power supply going out of regulation. Ensure that the external VDD load shunts current
greater than maximum injection current. This is the greatest risk when the MCU is not consuming power. Examples are:
if no system clock is present, or if clock rate is very low which would reduce overall power consumption. Also, the system
clock is not present during the power-up sequence until the PLL has attained lock.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
32
Freescale Semiconductor
Electrical Characteristics
Table 23. Active Current Consumption Specifications
Typical
Running from Running from Running from Running from
Characteristic
Symbol
Peak
Unit
SRAM,
Flash,
Flash, EPHY Flash, EPHY
EPHY Off
EPHY Off
10BaseT
100BaseT
Active current, core and I/O IDDR+IDDX
PLL @25 MHz
PLL @60 MHz
+IDDA
75
130
82
138
150
220
260
310
290
340
mA
Analog supply current
Normal operation
Low-power STOP
IDDA
20
15
20
15
20
15
20
15
30
50
mA
μA
1
Table 24. Current Consumption Specifications in Low-Power Modes
PLL @25 MHz PLL @60 MHz PLL @60 MHz
Mode2
Unit
(typical)3
(typical)3
(peak)4
STOP mode 3 (STPMD[1:0]=11)
0.2
7
1.0
—
—
—
—
—
—
mA
STOP mode 2 (STPMD[1:0]=10)
STOP mode 1 (STPMD[1:0]=01)
10
10
16
16
25
12
12
27
27
45
STOP mode 0 (STPMD[1:0]=00)
WAIT
DOZE
RUN
1
All values are measured with a 3.30 V power supply.
Refer to the “Power Management” chapter in the MCF52235 ColdFire® Integrated
Microcontroller Reference Manual for more information on low-power modes.
2
3
4
These values were obtained with CLKOUT and all peripheral clocks except for the CFM clock
disabled prior to entering low-power mode. The tests were performed at room temperature. All
code was executed from flash memory; running code from SRAM further reduces power
consumption.
These values were obtained with CLKOUT and all peripheral clocks enabled. All code was
executed from flash memory.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
33
Electrical Characteristics
2.4
Phase Lock Loop Electrical Specifications
Table 25. Oscillator and PLL Electrical Specifications
(VDD and VDDPLL = 2.7 to 3.6 V, VSS = VSSPLL = 0 V)
Characteristic
Symbol
Min
Max
Unit
Clock Source Frequency Range of EXTAL Frequency Range
MHz
• Crystal
fcrystal
fext
0.5
0
48.0
50.0 or 60.0
• External1
PLL reference frequency range
fref_pll
2
10.0
MHz
System frequency 2
External clock mode
On-Chip PLL Frequency
fsys
MHz
0
60
60
f
ref / 32
Loss of reference frequency 3, 5
Self clocked mode frequency 4, 5
Crystal start-up time 5, 6
fLOR
fSCM
tcst
100
1
1000
5
kHz
MHz
ms
—
10
EXTAL input high voltage
Crystal reference
VIHEXT
V
VDD- 1.0
2.0
VDD
VDD
External reference
EXTAL input low voltage
Crystal reference
VILEXT
V
VSS
VSS
1.0
0.8
External reference
XTAL output high voltage
IOH = 1.0 mA
VOL
VOL
V
V
VDD –1.0
—
XTAL output low voltage
IOL = 1.0 mA
—
—
—
0.5
—
XTAL load capacitance7
PLL lock time5,9
pF
tlpll
500
μs
Power-up to lock time 5, 7,8
With crystal reference
tlplk
—
—
10.5
500
ms
μs
Without crystal reference
Duty cycle of reference 5
Frequency un-LOCK range
Frequency LOCK range
tdc
40
60
1.5
% fsys
% fsys
% fsys
fUL
–1.5
–0.75
fLCK
Cjitter
0.75
CLKOUT period Jitter 5, 6, 8, 9,10, measured at fSYS Max
Peak-to-peak jitter (clock edge to clock edge)
Long term jitter (averaged over 2 ms interval)
—
—
10
0.01
% fsys
1
In external clock mode, it is possible to run the chip directly from an external clock source without enabling the PLL.
All internal registers retain data at 0 Hz.
Loss of reference frequency is the reference frequency detected internally that transitions the PLL into self-clocked mode.
2
3
4
Self-clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls below fLOR with
default MFD/RFD settings.
5
6
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
34
Freescale Semiconductor
Electrical Characteristics
Load capacitance determined from crystal manufacturer specifications and include circuit board parasitics.
7
8
Assuming a reference is available at power up, lock time is measured from the time VDD and VDDPLL are valid to RSTO
negating. If the crystal oscillator is the reference for the PLL, the crystal start up time must be added to the PLL lock time to
determine the total start-up time.
9
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fsys
.
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via VDDPLL and VSSPLL and variation in crystal oscillator frequency increase the Cjitter percentage
for a given interval
10 Based on slow system clock of 40 MHz measured at fsys max.
2.5
General Purpose I/O Timing
GPIO can be configured for certain pins of the QSPI, timers, UARTs, FEC, interrupts and USB interfaces. When in GPIO mode,
the timing specification for these pins is given in Table 26 and Figure 6.
The GPIO timing is met under the following load test conditions:
•
•
50 pF / 50 Ω for high drive
25 pF / 25 Ω for low drive
Table 26. GPIO Timing
Num
Characteristic
Symbol
Min
Max
Unit
G1
G2
G3
G4
CLKOUT high to GPIO output valid
CLKOUT high to GPIO output invalid
GPIO input valid to CLKOUT high
CLKOUT high to GPIO input invalid
tCHPOV
tCHPOI
tPVCH
tCHPI
—
1.5
9
10
—
—
—
ns
ns
ns
ns
1.5
CLKOUT
G2
G1
GPIO Outputs
G3
G4
GPIO Inputs
Figure 6. GPIO Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
35
Electrical Characteristics
2.6
Reset Timing
Table 27. Reset and Configuration Override Timing
(VDD = 2.7 to 3.6 V, VSS = 0 V, TA = TL to TH)1
Num
Characteristic
Symbol
Min
Max
Unit
R1 RSTI input valid to CLKOUT high
R2 CLKOUT high to RSTI input invalid
R3 RSTI input valid time 2
tRVCH
tCHRI
9
1.5
5
—
—
—
10
ns
ns
tRIVT
tCYC
ns
R4 CLKOUT high to RSTO valid
tCHROV
—
1
2
All AC timing is shown with respect to 50% VDD levels unless otherwise noted.
During low power STOP, the synchronizers for the RSTI input are bypassed and RSTI is asserted asynchronously to the
system. Therefore, RSTI must be held a minimum of 100ns.
CLKOUT
1R1
R2
R3
RSTI
R4
R4
RSTO
Figure 7. RSTI and Configuration Override Timing
2
2.7
I C Input/Output Timing Specifications
2
Table 28 lists specifications for the I C input timing parameters shown in Figure 8.
2
Table 28. I C Input Timing Specifications between I2C_SCL and I2C_SDA
Num
Characteristic
Start condition hold time
Min
Max
Units
I1
I2
I3
I4
I5
I6
I7
I8
I9
2 × tCYC
8 × tCYC
—
—
—
1
ns
ns
ms
ns
ms
ns
ns
ns
ns
Clock low period
SCL/SDA rise time (VIL = 0.5 V to VIH = 2.4 V)
Data hold time
0
—
1
SCL/SDA fall time (VIH = 2.4 V to VIL = 0.5 V)
Clock high time
—
4 × tCYC
0
—
—
—
—
Data setup time
Start condition setup time (for repeated start condition only)
Stop condition setup time
2 × tCYC
2 × tCYC
2
Table 29 lists specifications for the I C output timing parameters shown in Figure 8.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
36
Freescale Semiconductor
Electrical Characteristics
Table 29. I C Output Timing Specifications between I2C_SCL and I2C_SDA
2
Num
Characteristic
Start condition hold time
Min
Max
Units
I1 1
I2 1
I3 2
6 × tCYC
10 × tCYC
—
—
—
—
ns
ns
µs
Clock low period
I2C_SCL/I2C_SDA rise time
(VIL = 0.5 V to VIH = 2.4 V)
I4 1
I5 3
Data hold time
7 × tCYC
—
3
ns
ns
I2C_SCL/I2C_SDA fall time
(VIH = 2.4 V to VIL = 0.5 V)
—
I6 1
I7 1
I8 1
Clock high time
Data setup time
10 × tCYC
2 × tCYC
20 x tCYC
—
—
—
ns
ns
ns
Start condition setup time (for repeated start
condition only)
I9 1
Stop condition setup time
10 x tCYC
—
ns
1
Output numbers depend on the value programmed into the IFDR; an IFDR programmed with the
maximum frequency (IFDR = 0x20) results in minimum output timings as shown in Table 29. The I2C
interface is designed to scale the actual data transition time to move it to the middle of the SCL low
period. The actual position is affected by the prescale and division values programmed into the IFDR;
however, the numbers given in Table 29 are minimum values.
2
3
Because SCL and SDA are open-collector-type outputs, which the processor can only actively drive
low, the time SCL or SDA take to reach a high level depends on external signal capacitance and pull-up
resistor values.
Specified at a nominal 50-pF load.
Figure 8 shows timing for the values in Table 28 and Table 29.
I2
I6
I5
SCL
SDA
I3
I1
I4
I8
I9
I7
2
Figure 8. I C Input/Output Timings
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
37
Electrical Characteristics
2.8
EPHY Parameters
2.8.1
EPHY Timing
Table 30 and Figure 9 show the relevant EPHY timing parameters.
Table 30. EPHY Timing Parameters
Num
Characteristic
EPHY startup time
Symbol
Value
Unit
E1
tStart-Up
360
μs
EPHYEN
MDIO
E1
Figure 9. EPHY Timing
2.8.2
10BASE-T SQE (Heartbeat) Timing
Table 31 and Figure 10 show the relevant 10BASE-T SQE (heartbeat) timing parameters.
Table 31. 10BASE-T SQE (Heartbeat) Timing Parameters
Characteristic
Symbol
Min
Typ1
Max
Units
COL (SQE) delay after TXEN off
COL (SQE) pulse duration
t1
t2
—
—
1.0
1.0
—
—
μs
μs
1
Typical values are at 25°C.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
38
Freescale Semiconductor
Electrical Characteristics
TXC
TXEN
t1
t2
COL
Figure 10. 10BASE-T SQE (Heartbeat) Timing
2.8.3
10BASE-T Jab and Unjab Timing
Table 32 and Figure 11 show the relevant 10BASE-T jab and unjab timing parameters.
Table 32. 10BASE-T Jab and Unjab Timing Parameters
Parameter
Maximum transmit time
Unjab time
Symbol
Min
Typ1
Max
Units
t1
t2
—
—
98
—
—
ms
ms
525
1
Typical values are at 25°C.
TXEN
t1
TXD
COL
t2
Figure 11. 10BASE-T Jab and Unjab Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
39
Electrical Characteristics
2.8.4
Transceiver Characteristics
Table 33. 10BASE-T Transceiver Characteristics
Parameter
Symbol
Min
Typ
Max
Units
Test Conditions
Peak differential output voltage
VOP
2.2
2.5
2.8
V
With specified transformer and line
replaced by 100 Ω(± 1%) load
Transmit timing jitter
—
0
2
11
ns
Using line model specified in the
IEEE 802.3
Receive dc input impedance
Zin
—
10
—
kΩ
0.0 < Vin < 3.3 V
Receive differential squelch level
Vsquelch
300
400
585
mV
3.3 MHz sine wave input
Table 34. 100BASE-TX Transceiver Characteristics
Parameter
Symbol
Min
Typ
Max
Units
Test Conditions
Transmit Peak Differential Output
Voltage
VOP
0.95
1.00
1.05
V
With specified transformer and line
replaced by 100 Ω(±1%) load
Transmit Signal Amplitude
Symmetry
Vsym
trf
98
3
100
4
102
5
%
With specified transformer and line
replaced by 100 Ω (± 1%) load
Transmit Rise/Fall Time
ns
With specified transformer and line
replaced by 100 Ω (± 1%) load
Transmit Rise/Fall Time Symmetry
Transmit Overshoot/UnderShoot
Transmit Jitter
trfs
Vosh
—
–0.5
—
0
0
+0.5
5
ns
%
ns
V
See IEEE 802.3 for details
2.5
.6
1.4
—
Receive Common Mode Voltage
Receiver Maximum Input Voltage
Vcm
Vmax
—
—
1.6
—
VDDRX = 2.5 V
4.7
V
VDDRX = 2.5 V. Internal circuits
protected by divider in shutdown
2.9
Analog-to-Digital Converter (ADC) Parameters
Table 35 lists specifications for the analog-to-digital converter.
Table 35. ADC Parameters
1
Name
Characteristic
Low reference voltage
Min
Typical
Max
Unit
VREFL
VREFH
VDDA
VADIN
RES
INL
VSS
—
VREFH
VDDA
3.6
V
V
High reference voltage
VREFL
3.0
—
Analog supply voltage
3.3
V
Input voltages
VREFL
12
—
—
VREFH
12
V
Resolution
bits
LSB3
LSB
LSB
Integral non-linearity (full input signal range)2
Integral non-linearity (10% to 90% input signal range)4
Differential non-linearity
Monotonicity
—
±2.5
±3
INL
—
±2.5
±3
DNL
—
–1 < DNL < +1
<+1
Guaranteed
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
40
Freescale Semiconductor
Electrical Characteristics
1
Table 35. ADC Parameters (continued)
Name
Characteristic
Min
Typical
Max
Unit
fADIC
RAD
ADC internal clock
Conversion range
ADC power-up time5
Recovery from auto standby
Conversion time
0.1
VREFL
—
—
5.0
VREFH
13
1
MHz
—
V
tADPU
tREC
tADC
tADS
CADI
XIN
6
tAIC cycles6
—
0
tAIC cycles
—
6
—
tAIC cycles
Sample time
—
1
—
tAIC cycles
pF
Input capacitance
—
See Figure 12
—
Input impedance
—
See Figure 12
—
W
IADI
Input injection current7, per pin
VREFH current
—
—
0
3
mA
mA
mV
—
IVREFH
—
—
VOFFSET Offset voltage internal reference
EGAIN Gain error (transfer path)
VOFFSET Offset voltage external reference
—
±11
1
±15
1.01
—
.99
—
±3
mV
dB
SNR
THD
Signal-to-noise ratio
—
62 to 66
–75
75
—
Total harmonic distortion
Spurious free dynamic range
Signal-to-noise plus distortion
Effective number OF bits
—
—
dB
SFDR
SINAD
ENOB
—
—
dB
—
65
—
dB
9.1
10.6
—
Bits
1
2
3
4
5
6
7
All measurements were made at VDD = 3.3V, VREFH = 3.3V, and VREFL = ground
INL measured from VIN = VREFL to VIN = VREFH
LSB = Least Significant Bit
INL measured from VIN = 0.1VREFH to VIN = 0.9VREFH
Includes power-up of ADC and VREF
ADC clock cycles
The current that can be injected or sourced from an unselected ADC signal input without impacting the performance of the
ADC
2.9.1
Equivalent Circuit for ADC Inputs
Figure 10-17 shows the ADC input circuit during sample and hold. S1 and S2 are always open/closed at the same time that S3
is closed/open. When S1/S2 are closed and S3 is open, one input of the sample and hold circuit moves to (VREFH-VREFL)/2,
while the other charges to the analog input voltage. When the switches are flipped, the charge on C1 and C2 are averaged via
S3, with the result that a single-ended analog input is switched to a differential voltage centered about (VREFH-VREFL)/2. The
switches switch on every cycle of the ADC clock (open one-half ADC clock, closed one-half ADC clock). There are additional
capacitances associated with the analog input pad, routing, etc., but these do not filter into the S/H output voltage, as S1 provides
isolation during the charge-sharing phase. One aspect of this circuit is that there is an ongoing input current, which is a function
of the analog input voltage, VREF, and the ADC clock frequency.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
41
Electrical Characteristics
125W ESD Resistor
8pF noise damping capacitor
4
3
Analog Input
S1
C1
S/H
S3
C2
S2
(VREFH- VREFL) ÷ 2
2
1
C1 = C2 = 1pF
1
Parasitic capacitance due to package, pin-to-pin and pin-to-package base coupling; 1.8pF
2
3
4
Parasitic capacitance due to the chip bond pad, ESD protection devices and signal routing; 2.04pF
Equivalent resistance for the channel select mux; 100 ohms
Sampling capacitor at the sample and hold circuit. Capacitor C1 is normally disconnected from the input
and is only connected to it at sampling time; 1.4pF
1
5
-----------------------------------------------------------------------------------------
Equivalent input impedance, when the input is selected =
ADC CLOCK RATE × (1.4 × 10–12
)
Figure 12. Equivalent Circuit for A/D Loading
2.10 DMA Timers Timing Specifications
Table 36 lists timer module AC timings.
Table 36. Timer Module AC Timing Specifications
Name
Characteristic1
Min
Max
Unit
T1
T2
DTIN0 / DTIN1 / DTIN2 / DTIN3 cycle time
DTIN0 / DTIN1 / DTIN2 / DTIN3 pulse width
3 × tCYC
1 × tCYC
—
—
ns
ns
1
All timing references to CLKOUT are given to its rising edge.
2.11 EzPort Electrical Specifications
Table 37. EzPort Electrical Specifications
Name
Characteristic
Min
Max
sys / 2
Unit
EP1
EP1a
EP2
EP3
EP4
EP5
EP6
EPCK frequency of operation (all commands except READ)
EPCK frequency of operation (READ command)
EPCS_b negation to next EPCS_b assertion
EPCS_B input valid to EPCK high (setup)
EPCK high to EPCS_B input invalid (hold)
EPD input valid to EPCK high (setup)
—
f
MHz
MHz
ns
—
fsys / 8
—
2 × Tcyc
5
5
2
5
—
ns
—
ns
—
ns
EPCK high to EPD input invalid (hold)
—
ns
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
42
Freescale Semiconductor
Electrical Characteristics
Table 37. EzPort Electrical Specifications (continued)
Name
Characteristic
Min
Max
Unit
EP7
EP8
EP9
EPCK low to EPQ output valid (out setup)
EPCK low to EPQ output invalid (out hold)
EPCS_B negation to EPQ tri-state
—
0
12
—
12
ns
ns
ns
—
2.12 QSPI Electrical Specifications
Table 38 lists QSPI timings.
Table 38. QSPI Modules AC Timing Specifications
Characteristic
Name
Min
Max
Unit
QS1
QS2
QS3
QS4
QS5
QSPI_CS[3:0] to QSPI_CLK
1
—
2
510
10
—
tCYC
ns
QSPI_CLK high to QSPI_DOUT valid
QSPI_CLK high to QSPI_DOUT invalid (output hold)
QSPI_DIN to QSPI_CLK (input setup)
QSPI_DIN to QSPI_CLK (input hold)
ns
9
—
ns
9
—
ns
The values in Table 38 correspond to Figure 13.
QS1
QSPI_CS[3:0]
QSPI_CLK
QS2
QSPI_DOUT
QSPI_DIN
QS3
QS4
QS5
Figure 13. QSPI Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
43
Electrical Characteristics
2.13 JTAG and Boundary Scan Timing
Table 39. JTAG and Boundary Scan Timing
Num
Characteristics1
TCLK frequency of operation
Symbol
Min
Max
Unit
J1
J2
fJCYC
tJCYC
DC
1/4
—
—
3
fsys/2
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TCLK cycle period
4 × tCYC
J3
TCLK clock pulse width
tJCW
26
0
J4
TCLK rise and fall times
tJCRF
J5
Boundary scan input data setup time to TCLK rise
Boundary scan input data hold time after TCLK rise
TCLK low to boundary scan output data valid
TCLK low to boundary scan output high Z
TMS, TDI input data setup time to TCLK rise
TMS, TDI input data hold time after TCLK rise
TCLK low to TDO data valid
tBSDST
tBSDHT
tBSDV
4
—
—
33
33
—
—
26
8
J6
26
0
J7
J8
tBSDZ
0
J9
tTAPBST
tTAPBHT
tTDODV
tTDODZ
tTRSTAT
tTRSTST
4
J10
J11
J12
J13
J14
10
0
TCLK low to TDO high Z
0
TRST assert time
100
10
—
—
TRST setup time (negation) to TCLK high
1
JTAG_EN is expected to be a static signal. Hence, it is not associated with any timing.
J2
J3
J3
VIH
TCLK
VIL
(input)
J4
J4
Figure 14. Test Clock Input Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
44
Freescale Semiconductor
Electrical Characteristics
TCLK
VIL
VIH
J5
Input Data Valid
J6
Data Inputs
J7
J8
Data Outputs
Output Data Valid
Data Outputs
Data Outputs
J7
Output Data Valid
Figure 15. Boundary Scan (JTAG) Timing
TCLK
VIL
VIH
J9
J10
TDI
TMS
Input Data Valid
J11
TDO
Output Data Valid
J12
J11
TDO
TDO
Output Data Valid
Figure 16. Test Access Port Timing
TCLK
TRST
14
13
Figure 17. TRST Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
45
Electrical Characteristics
2.14 Debug AC Timing Specifications
Table 40 lists specifications for the debug AC timing parameters shown in Figure 19.
Table 40. Debug AC Timing Specification
60 MHz
Num
Characteristic
Units
Min
Max
D1
D2
PST, DDATA to CLKOUT setup
4
—
—
ns
ns
ns
ns
ns
ns
ns
ns
CLKOUT to PST, DDATA hold
DSI-to-DSCLK setup
1.5
D3
1 × tCYC
4 × tCYC
5 × tCYC
4
—
D4 1
DSCLK-to-DSO hold
—
D5
DSCLK cycle time
—
D6
BKPT input data setup time to CLKOUT Rise
BKPT input data hold time to CLKOUT Rise
CLKOUT high to BKPT high Z
—
D7
1.5
—
D8
0.0
10.0
1
DSCLK and DSI are synchronized internally. D4 is measured from the synchronized DSCLK input relative to
the rising edge of CLKOUT.
Figure 18 shows real-time trace timing for the values in Table 40.
CLKOUT
D1
D2
PST[3:0]
DDATA[3:0]
Figure 18. Real-Time Trace AC Timing
Figure 19 shows BDM serial port AC timing for the values in Table 40.
CLKOUT
DSCLK
DSI
D5
D3
Current
Past
Next
D4
DSO
Current
Figure 19. BDM Serial Port AC Timing
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
46
Freescale Semiconductor
Mechanical Outline Drawings
3
Mechanical Outline Drawings
This section describes the physical properties of the MCF52235 and its derivatives.
3.1
80-pin LQFP Package
–X–
X= L, M, N
4X
4X 20 TIPS
0.20 (0.008)
0.20 (0.008)
H
L–M
N
T
L–M
N
P
80
61
C
L
1
60
AB
AB
G
–M–
B1
VIEW Y
B
V
PLATING
F
–L–
3X VIEW Y
BASE
METAL
J
V1
41
20
D
U
21
40
–N–
M
S
S
0.13 (0.005)
T
L–M
N
A1
S1
SECTION AB–AB
ROTATED 90 CLOCKWISE
A
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –H– IS LOCATED AT BOTTOM OF
LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –L–, –M– AND –N– TO BE DETERMINED
AT DATUM PLANE –H–.
C
8X
2
0.10 (0.004)
T
–H–
–T–
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –T–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.250 (0.010) PER SIDE. DIMENSIONS A AND B
DO INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –H–.
SEATING
PLANE
VIEW AA
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL
NOT CAUSE THE LEAD WIDTH TO EXCEED 0.460
(0.018). MINIMUM SPACE BETWEEN
PROTRUSION AND ADJACENT LEAD OR
PROTRUSION 0.07 (0.003).
(W)
C2
S
0.05 (0.002)
MILLIMETERS
MIN MAX
14.00 BSC
7.00 BSC
14.00 BSC
7.00 BSC
INCHES
MIN MAX
0.551 BSC
0.276 BSC
0.551 BSC
0.276 BSC
1
DIM
A
A1
B
B1
C
C1
C2
D
E
F
G
J
0.25 (0.010)
2X R R1
GAGE
PLANE
–––
0.04
1.30
0.22
0.40
0.17
1.60
–––
0.002
0.051
0.009
0.016
0.007
0.063
0.24
1.50
0.38
0.75
0.33
0.009
0.059
0.015
0.030
0.013
(K)
C1
E
(Z)
0.65 BSC
0.026 BSC
VIEW AA
0.09
0.27
0.004
0.011
K
P
R1
S
S1
U
0.50 REF
0.325 BSC
0.020 REF
0.013 REF
0.004 0.008
0.630 BSC
0.315 BSC
0.10
0.20
16.00 BSC
8.00 BSC
0.09
0.16
0.004
0.006
V
16.00 BSC
0.630 BSC
0.315 BSC
0.008 REF
0.039 REF
V1
W
Z
8.00 BSC
0.20 REF
1.00 REF
0
01
02
0
0
9
10
–––
14
0
0
9
10
–––
14
CASE 917A–02
ISSUE C
DATE 09/21/95
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
47
Mechanical Outline Drawings
3.2 112-pin LQFP Package
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
48
Freescale Semiconductor
Mechanical Outline Drawings
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
49
Mechanical Outline Drawings
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
50
Freescale Semiconductor
Mechanical Outline Drawings
3.3 121 MAPBGA Package
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
51
Mechanical Outline Drawings
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
52
Freescale Semiconductor
Revision History
4 Revision History
Table 41. Revision History
Revision
Description
2 (Jul 2006)
• Updated available packages.
• Inserted mechanical drawings.
• Corrected signal pinouts and table.
3 (Feb 2007)
• Changed signal names TIN to DTIN and TOUT to DTOUT to match the MCF52235 ColdFire® Integrated
Microcontroller Reference Manual.
• Added overbars to extend over entire UCTSn and URTSn signal name.
• Added revision history.
• Formatting, layout, spelling, and grammar corrections.
• Updated block diagram and feature information to match Revision 3 of the MCF52235 ColdFire®
Integrated Microcontroller Reference Manual.
• Deleted the “PSTCLK cycle time” row from the “Debug AC Timing Specifications” table.
• Added “EPHY Timing” section.
• Deleted the “RAM standby supply voltage” entry from Table 19.
• Changed the minimum value for SNR, THD, SFDR, and SINAD in the “ADC parameters” table (was
TBD, is “—”).
• In the “Pin Functions by Primary and Alternate Purpose” table, changed the pin number for IRQ11 on
the 80 LQFP package (was “—”, is 41).
• Updated the “Thermal characteristics” table to include proper thermal resistance values.
• Added two tables, “Active Current Consumption Specifications” and “Current Consumption
Specifications in Low-Power Modes”, containing the latest current consumption information.
• Changed the value of Tj in the “Thermal Characteristics” table (was 105 °C, is 130 °C for all packages).
• Added the following note to and above the “Thermal Characteristics” table: “The use of this device in
one- or two-layer board designs is not recommended due to the limited thermal conductance provided
by those boards.”
• Added the value for Ψjt for the 121MAPBGA package (2.0 °C/W).
4 (May 2007)
5 (Sep 2007)
• Formatting, layout, spelling, and grammar corrections.
• Added load test condition information to the “General Purpose I/O Timing” section.
• Added specifications for VLVD and VLVDHYS to the “DC electrical specifications” table.
• Formatting, layout, spelling, and grammar corrections.
• Added information about the MCF52232 and MCF52236 devices.
• Revised the part number table to include full Freescale orderable part numbers.
• Synchronized the “Pin Functions by Primary and Alternate Purpose” table in the device reference
manual and data sheet.
• Added specifications for VREFL, VREFH, and VDDA to the “ADC Parameters” table.
• Added several EPHY specifications.
6 (Oct 2007)
• Formatting, layout, spelling, and grammar corrections.
• Changed the data sheet classification (was “Product Preview”, is “Advance Information”).
• Added the “EzPort Electrical Specifications” section.
• Updated the “ESD Protection” section.
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
Freescale Semiconductor
53
Revision History
Table 41. Revision History (continued)
Description
Revision
7 (Aug 2008)
• Changed document type from Advance Information to Technical Data.
• Added supported device list in subtitle.
• Removed preliminary text from electrical specifications section as device is fully characterized.
• Corrected IVREFH, VREFH current unit from “m” to “mA” in ADC specification table.
• Changed VOFFSET from TBD to — in ADC specification table.
8 (Jun 2009)
• Updated Orderable Part Number Summary table to include MCF52233CAL60A, MCF52235CAL60A,
and MCF52236AF50A parts
8 Sep 2009
8 April 2010
• Updated Table 25 — PLL Electrical Specifications.
• Updated Table 37— EzPort Electrical Specifications
MCF52235 ColdFire Microcontroller Data Sheet, Rev. 9
54
Freescale Semiconductor
相关型号:
MCF52235CAL60
32-BIT, FLASH, 60MHz, RISC MICROCONTROLLER, PQFP112, 20 X 20 MM. 1.40 MM HEIGHT, 0.65 MM PITCH, ROHS COMPLIANT, MS-026BFA, LQFP-112
NXP
©2020 ICPDF网 联系我们和版权申明