MK10X32VLH100R [FREESCALE]
K10 Sub-Family Data Sheet; K10次系列数据手册型号: | MK10X32VLH100R |
厂家: | Freescale |
描述: | K10 Sub-Family Data Sheet |
文件: | 总60页 (文件大小:859K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Document Number: K10P81M100SF2
Rev. 1, 11/2010
Freescale Semiconductor
Data Sheet: Product Preview
K10P81M100SF2
K10 Sub-Family Data Sheet
Supports the following:
MK10N512VLK100, MK10N512VMB100
Features
Human-machine interface
– Low-power hardware touch sensor interface (TSI)
– General-purpose input/output
•
•
Operating Characteristics
– Voltage range: 1.71 to 3.6 V
– Flash write voltage range: 1.71 to 3.6 V
– Temperature range (ambient): -40 to 105°C
•
•
•
Analog modules
– 16-bit SAR ADC with GA (x6
– 12-bit DAC
– Analog comparat(CMcontaining a 6-bit DAC
and programmble rence input
– Voltage reference
Performance
– Up to 100 MHz ARM Cortex-M4 core with DSP
instructions delivering 1.25 Dhrystone MIPS per
MHz
Memories and memory interfaces
– Up to 512 KB program flash memory on non-
FlexMemory devices
Timers
•
– Programable delay block
– Eit-chael motor control/general purpose/PWM
timers
– Up to 128 KB RAM
– Serial programming interface (EzPort)
– FlexBus external bus interface
– To-channel quadrature decoder/general purpose
timers
– Periodic interrupt timers
– 16-bit low-power timer
– Carrier modulator transmitter
– Real-time clock
Clocks
•
•
– 1 to 32 MHz crystal oscillator
– 32 kHz crystal oscillator
– Multi-purpose clock generator
Communication interfaces
– Controller Area Network (CAN) module
– SPI modules
– I2C modules
– UART modules
•
System peripherals
– 10 low-power modes to provide pooptimization
based on application requi
– Memory protection unit i-master
protection
– 16-channel DMA controller, pporting up to 64
request sources
– Secure Digital host controller (SDHC)
– I2S
– External watchdog monitor
– Software watchdog
– Low-leakage wakeup unit
Security and integrity modules
•
– Hardware CRC module to support fast cyclic
redundancy checks
– Hardware random-number generator
– 128-bit unique identification (ID) number per chip
This document contains information on a product under development. Freescale
reserves the right to change or discontinue this product without notice.
© 2010–2010 Freescale Semiconductor, Inc.
Preliminary
Table of Contents
1 Ordering parts...........................................................................4
6.1 Core modules....................................................................19
6.1.1 Debug trace timing specifications.........................19
6.1.2 JTAG electricals....................................................20
6.2 System modules................................................................23
6.3 Clock modules...................................................................23
6.3.1 MCG Specifications...............................................23
6.3.2 Oscillator Electrical Characteristics.......................25
1.1 Determining valid orderable parts......................................4
2 Part identification......................................................................4
2.1 Description.........................................................................4
2.2 Format...............................................................................4
2.3 Fields.................................................................................4
2.4 Example............................................................................5
3 Terminology and guidelines......................................................5
3.1 Definition: Operating requirement......................................5
3.2 Definition: Operating behavior...........................................6
3.3 Definition: Attribute............................................................6
3.4 Definition: Rating...............................................................7
3.5 Result of exceeding a rating..............................................7
3.6 Relationship between ratings and operating
6.3.2.1
6.3.2.2
Oscillator DC Electrical Specifications 25
Oscillator frequenspecifications......26
6.3.3 32kHz Oscillator Electril Chacteristics............27
6.3.3.1
32kHz Ocillator DC ctrical
Specificas..................................27
32kscillator Frequency
6.3.3.2
Sations......................................27
requirements......................................................................7
3.7 Guidelines for ratings and operating requirements............8
3.8 Definition: Typical value.....................................................8
3.9 Typical Value Conditions...................................................9
4 Ratings......................................................................................9
4.1 Thermal handling ratings...................................................9
4.2 Moisture handling ratings.............................................10
4.3 ESD handling ratings........................................................
4.4 Voltage and current operating ratings...................10
5 General.........................................................................11
5.1 Nonswitching electrical specificns..........................11
5.1.1 Voltage and Curreg Requiments......11
5.1.2 LVD and POR operatquirements.................12
5.1.3 Voltage and current operag behaviors..............13
5.1.4 Power mode transition operating behaviors..........13
5.1.5 Power consumption operating behaviors..............14
6.4 Memories and mmory interfaces.....................................28
6.4.1 Fl(FTFL) Electrical Characteristics.................28
.4.1.1
6.4.1.2
6.4.1.3
6.4.1.4
Flash Timing Parameters — Program
and Erase............................................28
Flash Timing Parameters —
Commands..........................................28
Flash (FTFL) Current and Power
Parameters..........................................29
Reliability Characteristics....................29
6.4.2 EzPort Switching Specifications............................29
6.4.3 Flexbus Switching Specifications..........................30
6.5 Security and integrity modules..........................................32
6.6 Analog...............................................................................32
6.6.1 ADC electrical specifications.................................32
6.6.1.1
6.6.1.2
6.6.1.3
16-bit ADC operating conditions..........33
16-bit ADC electrical characteristics....35
16-bit ADC with PGA operating
5.1.5.1
Diagram: Typical IDD_RUN operating
behavior...............................................16
conditions............................................38
16-bit ADC with PGA characteristics...39
5.1.6 EMC radiated emissions operating behaviors.......17
5.1.7 Designing with radiated emissions in mind...........18
5.1.8 Capacitance attributes..........................................18
5.2 Switching electrical specifications.....................................18
5.3 Thermal specifications.......................................................18
5.3.1 Thermal operating requirements...........................18
5.3.2 Thermal attributes.................................................19
6 Peripheral operating requirements and behaviors....................19
6.6.1.4
6.6.2 CMP and 6-bit DAC electrical specifications.........40
6.6.3 12-bit DAC electrical characteristics.....................41
6.6.3.1
6.6.3.2
12-bit DAC operating requirements.....41
12-bit DAC operating behaviors..........42
6.6.4 Voltage Reference Electrical Specifications..........44
6.7 Timers................................................................................45
6.8 Communication interfaces.................................................45
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
2
Freescale Semiconductor, Inc.
Preliminary
6.8.1 DSPI Switching Specifications for Low-speed
Operation..............................................................46
6.8.2 DSPI Switching Specifications (High-speed
6.9.2 TSI Electrical Specifications..................................52
7 Dimensions...............................................................................53
7.1 Obtaining package dimensions.........................................53
8 Pinout........................................................................................54
8.1 K10 Signal Multiplexing and Pin Assignments..................54
8.2 K10 Pinouts.......................................................................57
9 Revision History........................................................................58
mode)....................................................................47
6.8.3 SDHC Specifications.............................................49
6.8.4 I2S Switching Specifications.................................50
6.9 Human-machine interfaces (HMI)......................................52
6.9.1 General Switching Specifications..........................52
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
3
Preliminary
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web. To determine the orderable part
numbers for this device, go to www.freescale.com and perform a part number search for
the following device numbers: PK10 and MK10.
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the pecic part. You can use the
values of these fields to determine the specific part ou have received.
2.2 Format
Part numbers for this device have tfollowing format:
Q K## M FFF T PP CCC N
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Description
Values
Q
Qualification status
• M = Fully qualified, general market flow
• P = Prequalification
K##
M
Kinetis family
• K10
Flash memory type
• N = Program flash only
• X = Program flash and FlexMemory
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
4
Freescale Semiconductor, Inc.
Terminology and guidelines
Values
Field
Description
Program flash memory size
FFF
• 32 = 32 KB
• 64 = 64 KB
• 128 = 128 KB
• 256 = 256 KB
• 512 = 512 KB
• 1M0 = 1 MB
T
Temperature range (°C)
Package identifier
• V = –40 to 105
PP
• FM = 32 QFN (5 mm x 5 mm)
• FT = 48 QFN (7 mm x 7 mm)
• LF = 48 LQFP (7 mm x 7 mm)
• FX = 64 QFN (9 mm x 9 m)
• LH = 64 LQFP (10 mm x 1mm)
• LK = 80 LQFP (12 mx 12 m)
• MB = 81 MAPBG(8 mm mm)
• LL = 100 LQFP mm x 14 m)
• ML = 104 MAPBG8 mm x mm)
• LQ = 144 LQ(20 mm x 20 mm)
• MD = 144 MA (13 mm x 13 mm)
• MF 196 MGA (15 mm x 15 mm)
• MJ = 2MAPBGA (17 mm x 17 mm)
CCC
Maximum CPU frequency (MHz)
Packaging type
• 550 MHz
72 = 2 MHz
• 00 = 100 MHz
• 120 = 120 MHz
• 150 = 150 MHz
N
• R = Tape and reel
• (Blank) = Trays
2.4 Example
This is an example paber:
MK10N512VMD100
3 Terminology and guidelines
3.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
5
Preliminary
Terminology and guidelines
3.1.1 Example
This is an example of an operating requirement, which you must meet for the
accompanying operating behaviors to be guaranteed:
Symbol
Description
Min.
Max.
Unit
VDD
1.0 V core supply volt‐ 0.9
age
1.1
V
3.2 Definition: Operating behavior
An operating behavior is a specified value or range of values for a tecnical
characteristic that are guaranteed during operation if you meet the erating requirements
and any other specified conditions.
3.2.1 Example
This is an example of an operating behavior, which is guaranteed if you meet the
accompanying operating requirements:
Symbol
Description
Mi.
Max.
Unit
IWP
Digital I/O weak pullu
pulldown current
130
µA
3.3 Definition: Atibute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
3.3.1 Example
This is an example of an attribute:
Symbol
Description
Min.
Max.
Unit
CIN_D
Input capacitance: digi‐
tal pins
—
7
pF
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
6
Freescale Semiconductor, Inc.
Terminology and guidelines
3.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
• Operating ratings apply during operation of the chip.
• Handling ratings apply when the chip is not powered.
3.4.1 Example
This is an example of an operating rating:
Symbol
Description
Min.
Max.
Unit
VDD
1.0 V core supply volt‐ –0.3
age
1.2
V
3.5 Result of exceeding a rating
40
30
Tkelihd of permanent chip failure increases rapidly as
soocharacteristic begins to exceed one of its operating ratings.
20
10
0
Operating rating
Measured characteristic
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
7
Terminology and guidelines
3.6 Relationship between ratings and operating requirements
Fatal
range
Normal
operating
range
Fatal
range
- Probable permanent failure
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Correct operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- Probable permanent failure
Handling range
- No permanent failure
–∞
∞
3.7 Guidelines for ratings and operating requirents
Follow these guidelines for ratings and operating requirements
• Never exceed any of the chip’s ratings.
• During normal operation, don’t exceed any of te chip’s operating requirements.
• If you must exceed an operating requiremenat times other than during normal
operation (for example, during power seqencing), limit the duration as much as
possible.
3.8 Definition: Typicavalue
A typical value is a spd vale for a technical characteristic that:
• Lies within the raf values specified by the operating behavior
• Given the typical maufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
3.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol
Description
Min.
Typ.
Max.
Unit
IWP
Digital I/O weak
pullup/pulldown
current
10
70
130
µA
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
8
Freescale Semiconductor, Inc.
Ratings
3.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
5000
4500
4000
TJ
3500
150 °C
3000
10C
2500
25 °C
2000
1500
1000
500
0
0.90
0.95
1.00
1.05
0
VDD (V)
3.9 Typical Value Conditins
Typical values assume meet he following conditions (or other conditions as
specified):
Symbol
Description
Value
Unit
TA
Ambient temperature
25
°C
V
VDD
3.3 V supply voltage
3.3
4 Ratings
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
9
Ratings
4.1 Thermal handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
Solder temperature, leaded
—
—
260
245
°C
2
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.2 Moisture handling ratings
Symbol
Description
Min.
Ma
Unit
Notes
MSL
Moisture sensitivity level
—
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Refloensitiy Classification for Nonhermetic
Solid State Surface Mount Devices.
4.3 ESD handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
VHBM
Electrostatic discharge voltage, human bodmodel
-2000
+2000
V
1
VCDM
ILAT
Electrostatic discharge voltage, ed-evice model
Latch-up current at ambienemperatre of 85°C
-500
-100
+500
+100
V
2
mA
1. Determined according to Jandard ESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body
Model (HBM).
2. Determined according to JEDStandard JESD22-C101, Field-Induced Charged-Device Model Test Method for
Electrostatic-Discharge-WithstanThresholds of Microelectronic Components.
4.4 Voltage and current operating ratings
Symbol
Description
Min.
Max.
Unit
VDD
Digital supply voltage
–0.3
3.8
V
IDD
Digital supply current
—
185
5.5
mA
V
VDIO
VAIO
Digital input voltage (except RESET, EXTAL, and XTAL)
Analog, RESET, EXTAL, and XTAL input voltage
–0.3
–0.3
VDD + 0.3
V
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
10
Freescale Semiconductor, Inc.
General
Unit
Symbol
Description
Min.
Max.
ID
Instantaneous maximum current single pin limit (applies to all
port pins)
–25
25
mA
VDDA
IDDA
Analog supply voltage
VDD – 0.3
TBD
VDD + 0.3
TBD
3.8
V
mA
V
Analog supply current1
VBAT
RTC battery supply voltage
–0.3
VRAM
VDD voltage required to retain RAM
VBAT voltage required to retain the VBAT register file
1.2
—
V
VRFVBAT
TBD
—
V
1. The analog supply current is the sum of the active or disabled current for each of the analog modules n the device. See
each module's specification for its supply current.
5 General
5.1 Nonswitching electrical specifications
5.1.1 Voltage and Current Operating Requirements
Table 1. Voltage and currenoperating requirements
Symbol
Description
Min.
Max.
Unit
Notes
VDD
Supply voltage
1.71
3.6
V
VDDA
Analog supply voltage
1.71
–0.1
–0.1
3.6
0.1
0.1
V
V
V
VDD – VDDA VDD-to-VDDA differenal volte
VSS – VSSA VSS-to-VSSA dioltage
VIH
Input high voltage
• 2.7 V ≤ VDD ≤ 3.V
• 1.7 V ≤ VDD ≤ 2.7 V
0.7 × VDD
—
—
V
V
0.75 × VDD
VIL
Input low voltage
• 2.7 V ≤ VDD ≤ 3.6 V
• 1.7 V ≤ VDD ≤ 2.7 V
—
—
0.35 × VDD
0.3 × VDD
V
V
VHYS
Input hysteresis
0.06 × VDD
—
V
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
11
General
Table 1. Voltage and current operating requirements (continued)
Symbol
IIC
Description
Min.
Max.
Unit
Notes
DC injection current — single pin
• VIN > VDD
1
0
0
2
mA
mA
–0.2
• VIN < VSS
DC injection current — total MCU limit, includes sum
of all stressed pins
1
0
0
25
–5
mA
mA
• VIN > VDD
• VIN < VSS
1. All functional non-supply pins are internally clamped to VSS and VDD. Input must be current limito te value specified.
To determine the value of the required current-limiting resistor, calculate resistance values fopositive negative clamp
voltages, then use the larger of the two values. Power supply must maintain regulation withiperating VD range during
instantaneous and operating maximum current conditions. If positive injection current (Vn > V) is greaer than IDD, the
injection current may flow out of VDD and could result in external power supply goinout regulation. Ensure external
VDD load will shunt current greater than maximum injection current. This will be the gresk when the MCU is not
consuming power. Examples are: if no system clock is present, or if clock rate ery lohich would reduce overall
power consumption).
5.1.2 LVD and POR operating requiremets
Table 2. LVD and POR perting requirements
Symbol Description
Min.
Typ.
Max.
Unit
Notes
VPOR
Falling VDD POR detect voltage
TBD
1.1
TBD
V
VLVDH
Falling low-voltage detect thresholh
range (LVDV=01)
TBD
2.56
TBD
V
Low-voltage warning threshls — higrange
• Level 1 fallinV=00
1
VLVW1
VLVW2
VLVW3
VLVW4
VHYS
TBD
TBD
TBD
TBD
2.70
2.80
2.90
3.00
TBD
TBD
TBD
TBD
V
V
V
V
• Level 2 fallWV=01)
• Level 3 falling (WV=10)
• Level 4 falling (LVWV=11)
Low-voltage inhibit reset/recover hysteresis —
high range
60
mV
V
VLVDL
Falling low-voltage detect threshold — low range
(LVDV=00)
TBD
TBD
TBD
Low-voltage warning thresholds — low range
• Level 1 falling (LVWV=00)
1
VLVW1
VLVW2
VLVW3
VLVW4
TBD
TBD
TBD
TBD
1.80
1.90
2.00
2.10
TBD
TBD
TBD
TBD
V
V
V
V
• Level 2 falling (LVWV=01)
• Level 3 falling (LVWV=10)
• Level 4 falling (LVWV=11)
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
12
Freescale Semiconductor, Inc.
General
Notes
Table 2. LVD and POR operating requirements (continued)
Symbol Description
Min.
Typ.
Max.
Unit
VHYS
Low-voltage inhibit reset/recover hysteresis —
40
mV
low range
VBG
tLPO
Bandgap voltage reference
TBD
TBD
1.00
TBD
TBD
V
Internal low power oscillator period
factory trimmed
1000
μs
1. Rising thresholds are falling threshold + VHYS
5.1.3 Voltage and current operating behaviors
Table 3. Voltage and current operating behavior
Symbol
Description
Min.
Ma
Unit
Notes
VOH
Output high voltage — high drive strength
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = -10mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = -3mA
VDD – 5
VD– 0.5
—
—
V
V
Output high voltage — low drive strength
• 2.7 V ≤ VDD ≤ 3.6 V, IOH = -2mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOH = -0.6mA
VDD – 0.5
VDD – 0.5
—
—
V
V
IOHT
VOL
Output high current total for all ports
—
100
mA
Output low voltage — high drive h
• 2.7 V ≤ VDD ≤ 3.6 V, IO= A
• 1.71 V ≤ VDD ≤ 2.7 VL = 3mA
—
—
0.5
0.5
V
V
Output low voltw drive strength
• 2.7 V ≤ VDD .6 V, IOL = 2mA
• 1.71 V ≤ VDD ≤ 2.7 V, IOL = 0.6mA
—
—
0.5
0.5
V
V
IOLT
IIN
Output low current total for all ports
Input leakage current (per pin)
—
—
—
30
100
1
mA
μA
μA
kΩ
IOZ
Hi-Z (off-state) leakage current (per pin)
Internal weak pullup and pulldown resistors
1
RPU and
RPD
50
1
1. Measured at VIL max and VDD min
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
13
General
5.1.4 Power mode transition operating behaviors
In the table below, all specifications except tPOR, assume the following clock
configuration:
• CPU and system clocks = 100MHz
• Bus and FlexBus clocks = 50 MHz
• Flash clock = 25 MHz
Table 4. Power mode transition operating behaviors
Symbol
Description
Min.
Max.
U
Notes
tPOR
After a POR event, amount of time from the point VDD
reaches 1.8V to execution of the first instruction
across the operating temperature range of the chip.
—
300
μ
1
RUN → VLLS1 → RUN
• RUN → VLLS1
—
—
μs
μs
• VLLS1 → RUN
23.8
RUN → VLLS2 → RUN
• RUN → VLLS2
—
—
4.1
μs
μs
• VLLS2 → RUN
49.3
RUN → VLLS3 → RUN
• RUN → VLLS3
—
—
4.1
μs
μs
• VLLS3 → RUN
49.2
RUN → LLS → RUN
• RUN → LLS
—
—
4.1
5.9
μs
μs
• LLS → RU
RUN → STOP → R
• RUN → STOP
—
—
4.1
4.2
μs
μs
• STOP → RUN
RUN → VLPS → RUN
• RUN → VLPS
—
—
4.1
5.8
μs
μs
• VLPS → RUN
1. Normal boot (FTFL_OPT[LPBOOT]=1)
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
14
Freescale Semiconductor, Inc.
General
5.1.5 Power consumption operating behaviors
Table 5. Power consumption operating behaviors
Symbol Description
Min.
Typ.
Max.
Unit
Notes
IDD_RUN Run mode current — all peripheral clocks disa‐
bled, code executing from flash
1
• @ 1.8V
• @ 3.0V
—
—
40
42
TBD
TBD
mA
mA
IDD_RUN Run mode current — all peripheral clocks ena‐
bled, code executing from flash
2
3
• @ 1.8V
• @ 3.0V
—
—
55
56
TBD
TBD
A
IDD_RUN_M Run mode current — all peripheral clocks ena‐
bled and peripherals active, code executing from
AX
flash
—
—
85
85
TBD
mA
mA
• @ 1.8V
• @ 3.0V
IDD_WAIT Wait mode current at 3.0 V — all peripheral
clocks disabled
—
1
TBD
mA
4
IDD_STOP Stop mode current at 3.0 V
—
—
1.4
TBD
TBD
mA
mA
IDD_VLPR Very-low-power run mode current at 3.0 V — all
peripheral clocks disabled
1.25
5
6
7
IDD_VLPR Very-low-power run mode current at 3.0 — al
peripheral clocks enabled
—
TBD
TBD
mA
IDD_VLPW Very-low-power wait mode current V
IDD_VLPS Very-low-power stop mode cuent 3.0
—
—
—
1.05
30
TBD
TBD
TBD
mA
μA
μA
IDD_LLS
Low leakage stop mcurreat 3.0 V
12
IDD_VLLS3 Very low-leakagde 3 current at 3.0 V
• 128KB RAM dces
—
8
TBD
μA
IDD_VLLS2 Very low-leakage stop mode 2 current at 3.0 V
IDD_VLLS1 Very low-leakage stop mode 1 current at 3.0 V
—
—
—
4
2
TBD
TBD
TBD
μA
μA
nA
IDD_VBAT Average current when CPU is not accessing
RTC registers at 3.0 V
550
1. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock . MCG configured for FEI mode.
All peripheral clocks disabled.
2. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All
peripheral clocks enabled, but peripherals are not in active operation.
3. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All
peripheral clocks enabled, and peripherals are in active operation.
4. 25MHz core and system clock, 25MHz bus clock, and 12.5MHz FlexBus and flash clock. MCG configured for FEI mode.
5. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral
clocks disabled. Code executing from flash.
6. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral
clocks enabled but peripherals are not in active operation. Code executing from flash.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
15
Preliminary
General
7. 2 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for fast IRCLK mode. All peripheral
clocks disabled.
5.1.5.1 Diagram: Typical IDD_RUN operating behavior
The following data was measured under these conditions:
• MCG in FEI mode (39.0625 kHz IRC), except for 1 MHz core (FBE)
• All peripheral clocks disabled except FTFL
• LVD disabled
• No GPIOs toggled
• Code execution from flash
Figure 1. Run mode supply current vs. core frequency — all peripheral clocks disabled
The following data was measured under these conditions:
• MCG in FEI mode (39.0625 kHz IRC), except for 1 MHz core (FBE)
• All peripheral clocks enabled but peripherals are not in active operation
• LVD disabled
• No GPIOs toggled
• Code execution from flash
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
16
Freescale Semiconductor, Inc.
Preliminary
General
Figure 2. Run mode supply current vscore frequency — all peripheral clocks enabled
5.1.6 EMC radiated emisions operating behaviors
TabMC radiated emissions operating behaviors
Symbol
Description
Frequency
band (MHz)
Typ.
Unit
Notes
VRE1
VRE2
VRE3
VRE4
Radiated emissions voltage, band 1
Radiated emissions voltage, band 2
Radiated emissions voltage, band 3
Radiated emissions voltage, band 4
0.15–50
50–150
TBD
TBD
TBD
TBD
TBD
dBμV
1, 2
150–500
500–1000
0.15–1000
VRE_IEC_SAE IEC and SAE level
—
2, 3
1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150
kHz to 1 GHz Part 1: General Conditions and Definitions, IEC Standard 61967-2, Integrated Circuits - Measurement of
Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method, and SAE Standard J1752-3, Measurement of Radiated Emissions from Integrated Circuits—TEM/
Wideband TEM (GTEM) Cell Method.
2. VDD = 3 V, TA = 25 °C, fOSC = 16 MHz (crystal), fBUS = 20 MHz
3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions—TEM Cell and Wideband
TEM Cell Method, and Appendix D of SAE Standard J1752-3, Measurement of Radiated Emissions from Integrated
Circuits—TEM/Wideband TEM (GTEM) Cell Method.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
17
Preliminary
General
5.1.7 Designing with radiated emissions in mind
1. To find application notes that provide guidance on designing your system to
minimize interference from radiated emissions, go to www.freescale.com and
perform a keyword search for “EMC design.”
5.1.8 Capacitance attributes
Table 7. Capacitance attributes
Symbol
Description
Min.
Ma
Unit
CIN_A
Input capacitance: analog pins
—
7
pF
CIN_D
Input capacitance: digital pins
—
7
pF
5.2 Switching electrical specifications
Table 8. Device clock specifications
Symbol
Description
Min.
Max.
Unit
Notes
ormaun mode
fSYS
fBUS
System and core clock
Bus clock
—
—
—
—
100
50
MHz
MHz
MHz
MHz
FB_CLK
fFLASH
FlexBus clock
Flash clock
50
25
VLPR mode
fSYS
fBUS
System and core cloc
Bus clock
—
—
—
—
2
2
2
1
MHz
MHz
MHz
MHz
FB_CLK
fFLASH
FlexBus clock
Flash clock
5.3 Thermal specifications
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
18
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
5.3.1 Thermal operating requirements
Table 9. Thermal operating requirements
Symbol
Description
Min.
Max.
Unit
TJ
Die junction temperature
–40
–40
125
°C
TA
Ambient temperature
105
°C
5.3.2 Thermal attributes
Board Symbol Description
type
81
MAPBGA
80 LQFP Uni
Notes
Single-
layer (1s)
RθJA
Thermal resistance, junction to ambient (natural TBD
convection)
TBD
T
TBD
TBD
°C/W
°C/W
°C/W
°C/W
1
Four-layer RθJA
(2s2p)
Thermal resistance, junction to ambient (natural TBD
convection)
1
1
1
Single-
layer (1s)
RθJMA
Thermal resistance, junction to ambient (200 ft./ T
min. air speed)
Four-layer RθJMA
(2s2p)
Thermal resistance, junction to ambient (200 ft./ BD
min. air speed)
—
—
—
RθJB
RθJC
ΨJT
Thermal resistance, junction to board
Thermal resistance, junction tcase
TBD
TBD
TBD
TBD
TBD
°C/W
°C/W
°C/W
2
3
4
Thermal characterization ramer, junon to TBD
package top outside center atural onvection)
6 Peripheral operatig requirements and behaviors
6.1 Core modules
1. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test Method
Environmental Conditions—Forced Convection (Moving Air).
2. Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental Conditions
—Junction-to-Board.
3. Determined according to Method 1012.1 of MIL-STD 883, Test Method Standard, Microcircuits, with the cold plate
temperature used for the case temperature. The value includes the thermal resistance of the interface material between
the top of the package and the cold plate.
4. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental
Conditions—Natural Convection (Still Air).
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
19
Preliminary
Peripheral operating requirements and behaviors
6.1.1 Debug trace timing specifications
Table 10. Debug trace operating behaviors
Symbol
Description
Min.
Max.
Unit
Tcyc
Clock period
Frequency dependent
MHz
Twl
Twh
Tr
Low pulse width
High pulse width
Clock and data rise time
Clock and data fall time
Data setup
2
2
—
—
3
ns
ns
ns
ns
ns
ns
—
—
3
Tf
3
Ts
—
Th
Data hold
2
Figure 3. TRACE_CLKOT spcifications
TRACE_CLKOUT
TRACE_D[3:0]
Th
Ts
Th
Figure 4. Trace data specifications
6.1.2 JTAG electricals
Table 11. JTAG electricals
Symbol
Description
Min.
Max.
Unit
V
Operating voltage
2.7
3.6
J1
TCLK frequency of operation
• JTAG and CJTAG
• Serial Wire Debug
MHz
0
0
25
50
J2
TCLK cycle period
1/J1
—
ns
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
20
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 11. JTAG electricals (continued)
Symbol
Description
Min.
Max.
Unit
J3
TCLK clock pulse width
• JTAG and CJTAG
• Serial Wire Debug
ns
20
10
—
—
J4
J5
TCLK rise and fall times
—
20
0
3
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Boundary scan input data setup time to TCLK rise
Boundary scan input data hold time after TCLK rise
TCLK low to boundary scan output data valid
TCLK low to boundary scan output high-Z
TMS, TDI input data setup time to TCLK rise
TMS, TDI input data hold time after TCLK rise
TCLK low to TDO data valid
—
—
30
0
—
—
4
J6
J7
—
—
16
1
J8
J9
J10
J11
J12
J13
J14
—
—
100
8
TCLK low to TDO high-Z
4
TRST assert time
—
—
TRST setup time (negation) to TCLK high
J2
J4
J3
J3
TCLK (input)
Fiure . Test clock input timing
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
21
Peripheral operating requirements and behaviors
TCLK
J5
J6
Input data valid
Data inputs
Data outputs
Data outputs
Data outputs
J7
Output data valid
J8
J7
Output dad
Figure 6. Boundary scan (TAGtiming
TCLK
TDI/TMS
TDO
J9
J10
Input data valid
J11
Output data valid
J12
J11
TDO
Output data valid
TDO
Figure 7. Test Access Port timing
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
22
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
TCLK
TRST
J14
J13
Figure 8. TRST timing
6.2 System modules
There are no specifications necessary for the device's system modul.
6.3 Clock modules
6.3.1 MCG Specifications
Table 12. MCspecfications
Symbol Description
Min.
Typ.
Max.
Unit
Notes
fints_ft
fints_t
tirefsts
Internal reference frequency (slow clock) — cto‐
ry trimmed at nominal VDD and 25°
—
32.768
—
kHz
Internal reference frequency (slow k) user
trimmed
31.25
—
39.0625
kHz
Internal reference (ock) rtup time
—
—
TBD
0.1
4
µs
Δfdco_res_t Resolution of trimCO output frequency at
fixed voltage and terature — using SCTRIM
and SCFTRIM
0.3
%fdco
Δfdco_res_t Resolution of trimmed DCO output frequency at
fixed voltage and temperature — using SCTRIM
only
—
0.2
0.5
%fdco
Δfdco_t
Total deviation of trimmed DCO output frequency
over voltage and temperature
—
—
+ 0.5
- 1.0
0.5
3.5
%fdco
%fdco
Δfdco_t
Total deviation of trimmed DCO output frequency
over fixed voltage and temperature range of 0–
70°C
TBD
fintf_ft
Internal reference frequency (fast clock) — factory
trimmed at nominal VDD and 25°C
3.875
3
4
4.125
5
MHz
MHz
fintf_t
Internal reference frequency (fast clock) — user
trimmed
—
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
23
Peripheral operating requirements and behaviors
Table 12. MCG specifications (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
tirefstf
Internal reference startup time (fast clock)
—
TBD
TBD
µs
floc_low
Loss of external clock minimum frequency —
RANGE = 00
(3/5) x
fints_t
—
—
kHz
floc_high
Loss of external clock minimum frequency —
RANGE = 01, 10, or 11
(16/5) x
fints_t
—
—
kHz
FLL
fdco_t
DCO output fre‐
quency range —
user trimmed
Low range (DRS=00)
640 × fints_t
20
40
60
80
—
—
—
20.97
41.94
62.91
3.89
23.99
47.97
71.99
95.98
25
50
75
100
—
MHz
Mz
MHz
MHz
MHz
MHz
MHz
MHz
1, 2
and DMX32=0
Mid range (DRS=01)
1280 × fints_t
Mid-high range (DRS=10
192)0 × fints_t
High range (DRS=11)
2560 × fints_t
fdco_t_DMX3 DCO output fre‐
Low range (DRS=00)
732 × fints_t
3
quency range —
2
reference =
32,768Hz and
DMX32=1
Mid range (DRS=01)
1464 × fintt
—
Mid-high range (DR10)
2197 ×
—
High range RS=1)
29 × fints_t
—
Jcyc_fll
Jacc_fll
FLL period jitter
—
—
TBD
TBD
TBD
TBD
ps
ps
4
5
FLL accumulated jif DCO output over a 1µs
time window
tfll_acquire FLL target frequency acquisition time
—
—
1
ms
PLL
fvco
VCO operating frequency
48.0
2.0
—
—
—
100
4.0
—
MHz
MHz
ps
fpll_ref
Jcyc_pll
Jacc_pll
Dlock
PLL reference frequency range
PLL period jitter
400
TBD
—
6, 7
PLL accumulated jitter over 1µs window
Lock entry frequency tolerance
Lock exit frequency tolerance
Lock detector detection time
—
—
ps
6 , 7
1.49
4.47
—
2.98
5.97
%
Dunl
—
%
tpll_lock
—
0.15 +
ms
8
1075(1/
fpll_ref
)
1. The resulting system clock frequencies should not exceed their maximum specified values.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
24
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
2. This specification includes the 2% precision of the internal reference frequency (slow clock).
3. The resulting clock frequency must not exceed the maximum specified clock frequency of the device.
4. This specification was obtained at TBD frequency.
5. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed,
DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE,
FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running.
6. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of
each PCB and results will vary.
7. This specification was obtained at internal frequency of TBD.
8. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled
(BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes
it is already running.
6.3.2 Oscillator Electrical Characteristics
This section provides the electrical characteristics of the module.
6.3.2.1 Oscillator DC Electrical Specifications
Table 13. Oscillator DC electrical specifications, (VSOSC= 0 VDC) (TA = TL to TH)
Symbol Description
M
yp.
Max.
Unit
Notes
VDD33OSC 3.3 V supply voltage
71
—
3.6
V
IDDOSC
Supply current — low-power mode
1
• 32 kHz
• 1 MHz
• 4 MHz
• 8 MHz
• 16 MHz
• 24 MHz
• 32 MHz
—
—
—
—
—
—
—
500
100
200
300
700
1.2
—
—
—
—
—
—
—
nA
μA
μA
μA
μA
mA
mA
1.5
IDDOSC
Supply current — high gin mode
• 32 kHz
1
—
—
—
—
—
—
—
25
200
400
800
1.5
3
—
—
—
—
—
—
—
μA
μA
• 1 MHz
• 4 MHz
μA
• 8 MHz
μA
• 16 MHz
mA
mA
mA
• 24 MHz
• 32 MHz
4
Cx
Cy
EXTAL load capacitance
XTAL load capacitance
—
—
—
—
—
—
2, 3
2 , 3
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
25
Peripheral operating requirements and behaviors
Table 13. Oscillator DC electrical specifications, (VSSOSC= 0 VDC) (TA = TL to TH)
(continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
RF Feedback resistor — low-frequency, low-power
—
—
—
MΩ
2 , 3
mode
Feedback resistor — low-frequency, high-gain
mode
—
—
—
—
10
—
1
—
—
—
—
MΩ
MΩ
MΩ
k
Feedback resistor — high-frequency, low-power
mode (1 – 8 MHz, 8 – 32 MHz)
Feedback resistor — high-frequency, high-gain
mode (1 – 8 MHz, 8 – 32 MHz)
RS
Series resistor — low-frequency, low-power
mode
—
Series resistor — low-frequency, high-gain mode
—
—
200
—
—
kΩ
kΩ
Series resistor — high-frequency, low-power
mode
Series resistor — high-frequency, high-gain
mode
• 1 MHz resonator
• 2 MHz resonator
• 4 MHz resonator
• 8 MHz resonator
• 16 MHz resonator
• 20 MHz resonator
• 32 MHz resonator
—
—
—
—
—
—
—
6.6
3.3
0
—
—
—
—
—
—
—
—
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
V
0
0
0
0
Vpp
Peak-to-peak amplitude of osllation illator
mode) — low-freque, low-wer mode
0.6
Peak-to-peak aoscillaion (oscillator
mode) — low-freq, high-gain mode
0.75 ×
VDD33OSC
VDD33OSC
—
—
—
V
V
V
Peak-to-peak amplitudf oscillation (oscillator
mode) — high-frequency, low-power mode
—
0.6
Peak-to-peak amplitude of oscillation (oscillator
mode) — high-frequency, high-gain mode
0.75 ×
VDD33OSC
VDD33OSC
1. VDD33OSC=3.3 V, Temperature =27 °C, Cx/Cy=20 pF
2. See crystal or resonator manufacturer's recommendation
3. RF and Cx,Cy are integrated in low-frequency, low-power mode and must not be attached externally
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
26
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
6.3.2.2 Oscillator frequency specifications
Table 14. Oscillator frequency specifications, (VDD33OSC = VDD33OSC (min) to
VDD33OSC (max), TA = TL to TH)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
fosc_lo
fosc_hi_1
fosc_hi_2
Oscillator crystal or resonator frequency — low
frequency mode
32
—
40
kHz
Oscillator crystal or resonator frequency — high
frequency mode (low range)
1
8
—
—
8
MHz
MHz
Oscillator crystal or resonator frequency — high
frequency mode (high range)
32
tdc_extal
tcst
Input clock duty cycle (external clock mode)
40
—
50
60
—
Crystal start-up time — 32 kHz low-frequency,
low-power mode
TBD
ms
1, 2, 3
Crystal start-up time — 32 kHz low-frequency,
high-gain mode
—
—
—
800
4
—
—
ms
ms
ms
Crystal start-up time — 8 MHz high-frequency,
low-power mode
Crystal start-up time — 8 MHz high-frequency,
high-gain mode
3
1. This parameter is characterized before qualification rather thn 1% tested.
2. Proper PC board layout procedures must be followeto acve spifications.
3. Crystal start up time is defined as the time between the oscillar being enabled and the OSCINIT bit in the MCG_S
register being set.
6.3.3 32kHz Oscillator Elecrical Characteristics
This section describes odulelectrical characteristics.
6.3.3.1 32kHz Oscillaor DC Electrical Specifications
Table 15. 32kHz Oscillator Module DC Electrical Specifications (VSSOSC= 0 VDC)
(TA = TL to TH)
Symbol
Description
Min.
Typ.
Max.
Unit
VBAT
Supply voltage
1.71
—
3.6
V
RF
Internal feedback resistor
—
—
—
—
100
2.5
15
—
—
—
—
MΩ
pF
pF
V
Cpara
Cload
Vpp
Parasitical capacitance of EXTAL32 and XTAL32
Internal load capacitance (programmable)
Peak-to-peak amplitude of oscillation
0.6
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
27
Peripheral operating requirements and behaviors
6.3.3.2 32kHz Oscillator Frequency Specifications
Table 16. 32kHz oscillator frequency specifications (VDD33OSC = VDD33OSC (min)
to VDD33OSC (max), TA = TL to TH)
Symbol Description
Min.
—
Typ.
32
Max.
—
Unit
kHz
ms
Notes
fosc_lo
tstart
Oscillator crystal
Crystal start-up time
—
1000
—
1, 2
1. This parameter is characterized before qualification rather than 100% tested.
2. Proper PC board layout procedures must be followed to achieve specifications.
6.4 Memories and memory interfaces
6.4.1 Flash (FTFL) Electrical Characteristics
This section describes the electrical characteristics of the FTFL module.
6.4.1.1 Flash Timing Parameters — Proram and Erase
The following characteristics represent the amunt of time the internal charge pumps are
active and do not include command ovrhead.
Table 17. NVM gram/erase timing characteristics
Symbol Description
Min.
Typ.
Max.
Unit
Notes
thvpgm4
thversscr
thversblk
Longword Prograoltage me
—
20
TBD
μs
Sector Erase highge time
Erase Block high-voltatime
—
—
20
100
800
ms
ms
1
1
160
1. Maximum time based on expectations at cycling end-of-life.
6.4.1.2 Flash Timing Parameters — Commands
Table 18. Flash command timing characteristics
Symbol Description
Min.
Typ.
Max.
Unit
Notes
trd1blk
Read 1s Block execution time
—
—
1.4
ms
trd1sec2k
Read 1s Section execution time (2 KB flash sec‐
tor)
—
—
40
μs
tpgmchk
Program Check execution time
—
—
35
μs
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
28
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 18. Flash command timing characteristics (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
trdrsrc
tpgm4
tersblk
tersscr
Read Resource execution time
—
—
35
μs
1
Program Longword execution time
Erase Flash Block execution time
Erase Flash Sector execution time
—
—
—
—
50
160
20
TBD
800
100
TBD
μs
ms
ms
ms
2
2
tpgmsec2k Program Section execution time (2 KB flash sec‐
tor)
TBD
trd1all
Read 1s All Blocks execution time
Read Once execution time
—
—
—
—
—
—
—
2.8
35
ms
s
μ
ms
μs
trdonce
1
tpgmonce Program Once execution time
50
320
—
TB
1600
tersall
Erase All Blocks execution time
2
1
tvfykey
Verify Backdoor Access Key execution time
1. Assumes 25MHz flash clock frequency.
2. Maximum times for erase parameters based on expectations at cyclig end-life.
6.4.1.3 Flash (FTFL) Current and Power Paameters
Table 19. Flash (FTFL) cuent ad power parameters
Symbol
Description
Typ.
Unit
mA
IDD_PGM
Worst case programming current irogram flash
10
6.4.1.4 Reliability Charaeristics
ble 20. NVM reliability characteristics
Typ.1
Symbol Description
Min.
Program Flash
Max.
Unit
Notes
tnvmretp10k Data retention after up to 10 K cycles
tnvmretp1k Data retention after up to 1 K cycles
tnvmretp100 Data retention after up to 100 cycles
nnvmcycp Cycling endurance
5
10
TBD
TBD
TBD
TBD
—
—
—
—
years
years
years
cycles
2
2
2
3
15
10 K
1. Typical data retention values are based on intrinsic capability of the technology measured at high temperature derated to
25°C. For additional information on how Freescale defines typical data retention, please refer to Engineering Bulletin
EB618.
2. Data retention is based on Tjavg = 55°C (temperature profile over the lifetime of the application).
3. Cycling endurance represents number of program/erase cycles at -40°C ≤ Tj ≤ 125°C
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
29
Preliminary
Peripheral operating requirements and behaviors
6.4.2 EzPort Switching Specifications
Table 21. EzPort switching specifications
Num
Description
Min.
2.7
—
Max.
3.6
Unit
V
Operating voltage
EP1
EZP_CK frequency of operation (all commands except
READ)
fSYS/2
MHz
EP1a
EP2
EP3
EP4
EP5
EP6
EP7
EP8
EP9
EZP_CK frequency of operation (READ command)
EZP_CS negation to next EZP_CS assertion
EZP_CS input valid to EZP_CK high (setup)
EZP_CK high to EZP_CS input invalid (hold)
EZP_D input valid to EZP_CK high (setup)
EZP_CK high to EZP_D input invalid (hold)
EZP_CK low to EZP_Q output valid (setup)
EZP_CK low to EZP_Q output invalid (hold)
EZP_CS negation to EZP_Q tri-state
—
fSYS/8
—
MHz
ns
2 x tEZP_CK
5
5
—
ns
—
ns
2
—
ns
5
—
ns
—
0
12
—
ns
ns
—
12
ns
EZP_CK
EP3
EP
EP2
EZP_CS
P9
7
P8
EZP_Q (output)
EZP_D (input)
EP5
EP6
Figure 9. EzPort Timing Diagram
6.4.3 Flexbus Switching Specifications
All processor bus timings are synchronous; input setup/hold and output delay are given in
respect to the rising edge of a reference clock, FB_CLK. The FB_CLK frequency may be
the same as the internal system bus frequency or an integer divider of that frequency.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
30
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
The following timing numbers indicate when data is latched or driven onto the external
bus, relative to the Flexbus output clock (FB_CLK). All other timing relationships can be
derived from these values.
Table 22. Flexbus switching specifications
Num
Description
Min.
2.7
—
Max.
3.6
50
Unit
V
Notes
Operating voltage
Frequency of operation
Clock period
Mhz
ns
FB1
FB2
FB3
FB4
FB5
20
—
Address, data, and control output valid
Address, data, and control output hold
Data and FB_TA input setup
Data and FB_TA input hold
TBD
0
11.5
—
1
1
2
2
ns
8.5
0.5
—
ns
ns
1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FBT, FB_TSIZ[1:0], and FB_TS.
2. Specification is valid for all FB_AD[31:0] and FB_TA.
FB1
FB_CLK
FB5
B3
FB_A[Y]
Adss
FB4
FB2
FB_D[X]
FB_RW
Address
Data
FB_TS
AA=1
AA=0
FB_CSn
FB_OEn
FB_BE/BWEn
FB_TA
FB4
FB5
AA=1
AA=0
FB_TSIZ[1:0]
TSIZ
Figure 10. FlexBus read timing diagram
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
31
Peripheral operating requirements and behaviors
FB1
FB_CLK
FB3
FB_A[Y]
Address
FB2
FB_D[X]
Address
Data
FB_RW
FB_TS
AA=1
AA=0
FB_CSn
FB_OEn
FB_BE/BWEn
FB_TA
FB4
FB5
AA=1
AA
FB_TSIZ[1:0]
TSI
Figur11. FlexBus write timing diagram
6.5 Security and integrity modules
There are no specifications necessary for the device's security and integrity modules.
6.6 Analog
6.6.1 ADC electrical specifications
The 16-bit accuracy specifications listed in Table 23 and Table 24 are achievable on the
differential pins (ADCx_DP0, ADCx_DM0, ADC, ADCx_DP1, ADCx_DM1,
ADCx_DP3, and ADCx_DP3). The ADCx_DP2 and ADCx_DM2 ADC inputs are used
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
32
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
as the PGA inputs and are not direct device pins. Accuracy specifications for these pins
are defined in Table 25 and Table 26. All other ADC channels meet the 13-bit
differential/12-bit single-ended accuracy specifications.
6.6.1.1 16-bit ADC operating conditions
Table 23. 16-bit ADC operating conditions
Typ.1
Symbol Description
Conditions
Absolute
Min.
1.71
-100
Max.
3.6
Unit
V
Notes
VDDA
Supply voltage
Supply voltage
—
ΔVDDA
Delta to VDD (VDD
-
0
+100
mV
2
2
VDDA
)
ΔVSSA
Ground voltage
Delta to VSS (VSS
-
-100
0
+100
mV
VSSA
)
VREFH
ADC reference
voltage high
1.13
VSSA
VREFL
VDDA
VSSA
—
VDDA
V
V
VREFL
Reference volt‐
age low
VA
VADIN
CADIN
Input voltage
VREFH
V
Input capaci‐
tance
• 16 bit modes
—
4
10
5
pF
• 8/10/12 bit
modes
RADIN
Input resistance
2
5
kΩ
Tantinuon the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
33
Peripheral operating requirements and behaviors
Table 23. 16-bit ADC operating conditions (continued)
Typ.1
Symbol Description
Conditions
Min.
Max.
Unit
Notes
RAS
Analog source
resistance
16 bit modes
External to MCU
• fADCK > 8MHz
—
—
—
—
—
—
0.5
1
kΩ
kΩ
kΩ
Assumes
ADLSMP=0
• fADCK = 4–8MHz
• fADCK < 4MHz
2
13/12 bit modes
• fADCK > 16MHz
• fADCK > 8MHz
• fADCK = 4–8MHz
• fADCK < 4MHz
—
—
—
—
—
—
—
—
0.5
1
kΩ
kΩ
kΩ
kΩ
2
5
11/10 bit modes
• fADCK > 8MHz
• fADCK = 4–8MHz
• fADCK < 4MHz
—
—
—
—
—
—
2
5
kΩ
kΩ
kΩ
10
9/8 bit modes
—
—
—
—
5
kΩ
kΩ
• fADCK > 8MHz
• fADCK < 8MHz
10
fADCK
ADC conversion ADLPC=0, ADHSC=
clock frequency
• 16 bit modes
1.0
1.0
—
—
TBD
TBD
MHz
MHz
• ≤13 bit m
ADLPC=ADHSC=0
6 bit des
1.0
1.0
—
—
8.0
MHz
MHz
≤13 bit modes
12.0
ADLPC=1, ADHSC=1
• 16 bit modes
1.0
1.0
—
—
5.0
8.0
MHz
MHz
• ≤13 bit modes
ADLPC=1, ADHSC=0
• 16 bit modes
1.0
1.0
—
—
2.5
5.0
MHz
MHz
• ≤13 bit modes
1. Typical values assume VDDA = 3.0 V, Temp = 25°C, fADCK = 1.0 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2. DC potential difference.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
34
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
SIMPLIFIED
INPUT PIN EQUIVALENT
CIRCUIT
ZADIN
SIMPLIFIED
CHANNEL SELECT
Pad
ZAS
leakage
due to
input
CIRCUIT
ADC SAR
ENGINE
RAS
RADIN
protection
VADIN
CAS
VAS
RADIN
INPUT PIN
INPUT PIN
INPUT PIN
RADIN
RADIN
CADIN
Figure 12. ADC input impedance euivalency diagram
6.6.1.2 16-bit ADC electrical characteristics
Table 24. 16-bit ADC characterstics (VREFH = VDDA, VREFL = VSSA
)
Conditions1
• ADC=1, AHSC=0
Typ.2
215
340
470
610
Symbol Description
Min.
—
Max.
—
Unit
Notes
IDDA
Supply current
μA
μA
μA
μA
ADLSMP=
0
DLP1, ADHSC=1
ADLPC=0, ADHSC=0
ADLPC=0, ADHSC=1
—
—
ADCO=1
—
—
—
—
Supply current
• Stop, reset, module off
• ADLPC=1, ADHSC=0
• ADLPC=1, ADHSC=1
• ADLPC=0, ADHSC=0
• ADLPC=0, ADHSC=1
—
0.01
2.4
4.0
5.2
6.2
0.8
μA
ADC asynchro‐
nous clock
source
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
tADACK = 1/
fADACK
MHz
MHz
MHz
MHz
fADACK
Sample Time
See Reference Manual chapter for sample times
Conversion Time See Reference Manual chapter for conversion times
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
35
Peripheral operating requirements and behaviors
Table 24. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Conditions1
• 16 bit differential
Typ.2
14.0
13.0
1.5
Symbol Description
Min.
—
Max.
TBD
TBD
TBD
TBD
TBD
TBD
1.0
Unit
Notes
LSB3
TUE
DNL
INL
Total unadjusted
error
Max hard‐
ware aver‐
aging
(AVGE =
%1, AVGS
= %11)
• 16 bit single-ended
• 13 bit differential
• 12 bit single-ended
• 11 bit differential
• 10 bit single-ended
• 9 bit differential
—
—
—
TBD
0.8
—
—
TBD
0.5
—
• 8 bit single-ended
—
0.5
1.0
LS
LSB3
LSB3
Differential non-
linearity
• 16 bit differential
• 16 bit single-ended
• 13 bit differential
• 12 bit single-ended
• 11 bit differential
• 10 bit single-ended
• 9 bit differential
—
—
—
—
—
—
—
—
2.5
2.5
0.7
0.7
0.5
TD
0.2
0.2
TB
TBD
D
D
TBD
TBD
0.5
Max hard‐
ware aver‐
aging
(AVGE =
%1, AVGS
= %11)
• 8 bit single-ended
0.5
Integral non-line‐
arity
• 16 bit differential
• 16 bit single-ded
• 13 bit differential
• 12 bit singed
• 11 bit diffntial
• 10 single-ended
bit difrential
—
—
—
—
—
—
—
—
-6 to +2.5
-2 to +12
1.0
—
Max aver‐
aging
—
TBD
TBD
TBD
TBD
0.5
1.0
0.5
0.5
0.3
8 bit single-ended
0.3
0.5
EZS
Zero-scale error
• 6 bit differential
• 16 bit single-ended
• 13 bit differential
• 12 bit single-ended
• 11 bit differential
• 10 bit single-ended
• 9 bit differential
—
—
—
—
—
—
—
—
4.0
4.0
0.7
0.7
0.4
0.4
0.2
0.2
—
VADIN
=
VSSA
—
TBD
TBD
TBD
TBD
0.5
• 8 bit single-ended
0.5
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
36
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 24. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Conditions1
• 16 bit differential
Typ.2
0 to +10
0 to +14
1.0
Symbol Description
Min.
—
Max.
—
Unit
Notes
LSB3
EFS
Full-scale error
VADIN
=
VDDA
• 16 bit single-ended
• 13 bit differential
• 12 bit single-ended
• 11 bit differential
• 10 bit single-ended
• 9 bit differential
—
—
—
TBD
TBD
TBD
TBD
0.5
—
TBD
0.4
—
—
0.4
—
0.2
• 8 bit single-ended
—
0.2
0.5
LS
EQ
Quantization er‐
ror
• 16 bit modes
• ≤13 bit modes
—
—
-1 to 0
—
—
0.5
ENOB
Effective number 16 bit differential mode
4
of bits
• Avg=32
TBD
TBD
TBD
TD
D
1.
BD
14.
BD
13.2
BD
TBD
TBD
TBD
TBD
bits
bits
bits
bits
bits
• Avg=16
• Avg=8
• Avg=4
• Avg=1
16 bit single-ended mode
• Avg=32
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
bits
bits
bits
bits
bits
• Avg=16
• Avg=8
• Avg4
Avg=
Signal-to-noise
plus distortion
ENOB
SINAD
THD
6.02 × ENOB + 1.76
dB
Total harmonic
distortion
16 bit differential mode
• Avg=32
4
4
—
—
-94
TBD
TBD
dB
dB
16 bit single-ended mode
• Avg=32
TBD
SFDR
Spurious free dy‐ 16 bit differential mode
namic range
• Avg=32
TBD
TBD
95
—
—
dB
dB
16 bit single-ended mode
• Avg=32
TBD
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
37
Peripheral operating requirements and behaviors
Table 24. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued)
Conditions1
Typ.2
Symbol Description
Min.
Max.
Unit
Notes
EIL
Input leakage er‐
ror
IIn × RAS
mV
IIn = leak‐
age cur‐
rent
(refer to
the MCU's
voltage
and cur‐
rent oper‐
ating rat‐
ings)
Temp sensor
slope
• –40°C to 25°C
• 25°C to 105°C
—
—
TBD
TBD
—
—
m°C
mV/
VTEMP25 Temp sensor
voltage
25°C
—
TBD
—
mV
1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA
2. Typical values assume VDDA = 3.0 V, Temp = 25°C, fADCK = 2.0 MHz unlestherwistated. Typical values are for
reference only and are not tested in production.
1 LSB = (VREFH - VREFL)/2N
3.
4. Input data is 1 kHz sine wave.
6.6.1.3 16-bit ADC with PGA operating conditions
Table 25. 16-bit ADC with GA operating conditions
Typ.1
Symbol Description
VDDA Supply voltage
VREFPGA PGA ref voltage
Conditions
Min.
Max.
Unit
V
Notes
Absolute
1.71
—
3.6
VREFOUT VREFOUT VREFOUT
V
2, 3
VADIN
RPGA
Input voltage
VSSA
—
VDDA
V
Input impedance G= 1, 2, 4, 8
Gain = 16, 32
TBD
TBD
TBD
TBD
TBD
TBD
—
64
32
TBD
TBD
TBD
TBD
TBD
TBD
—
kΩ
Gain = 64
16
RPGAD
Differntial input
impedance
Gain = 1, 2, 4, 8
Gain = 16, 32
Gain = 64
128
64
kΩ
IN+ to IN-
32
RAS
TS
Analog source
resistance
Gain = 16, 32
100
Ω
4
5
ADC sampling
time
Gain = 64
1.25
—
—
µs
1. Typical values assume VDDA = 3.0 V, Temp = 25°C, fADCK = 6 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2. ADC must be configured to use the internal voltage reference (VREFOUT)
3. PGA reference connected to the VREFOUT pin. If the user wishes to drive VREFOUT with a voltage other than the output
of the VREF module, the VREF module must be disabled.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
38
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
4. The analog source resistance (RAS), external to MCU, should be kept as minimum as possible. Increased RAS causes drop
in PGA gain without affecting other performances. This is not dependent on ADC clock frequency.
5. The minimum sampling time is dependent on input signal frequency and ADC mode of operation. A minimum of 1.25µs
time should be allowed for Fin=4 kHz at 16-bit differential mode. Recommended ADC setting is: ADLSMP=1, ADLSTS=2 at
8 MHz ADC clock. The ADLSTS bits can be adjusted for different ADC clock frequency
6.6.1.4 16-bit ADC with PGA characteristics
Table 26. 16-bit ADC with PGA characteristics
Typ.1
Symbol
Description
Conditions
Min.
TBD
—
Max.
TBD
TBD
Unit
μA
Notes
IDDA_PGA Supply current
590
ILKG
G
Leakage current
Gain2
PGA disabled
< 1
A
• PGAG=0
• PGAG=1
• PGAG=2
• PGAG=3
• PGAG=4
• PGAG=5
• PGAG=6
TBD
TBD
TBD
TBD
TBD
TBD
T
1
TBD
D
D
TBD
TBD
TBD
dB
dB
dB
dB
dB
dB
dB
R
AS < 100Ω
2
3.9
T
BD
29
BD
GA
Gain error
—
—
0.5
dB
R
AS < 100Ω
BW
Input signal band‐
width
• 16-bit modes
• < 16-bit mod
—
—
—
—
4
kHz
kHz
dB
40
—
PSRR
CMRR
Power supply re‐ Gain=1
jection ration
TBD
TBD
VDDA= 3V
100mV,
fVDDA= 50Hz,
60Hz
Common mode
rejection ratio
Gain
TBD
TBD
TBD
TBD
—
—
dB
dB
VCM=
500mVpp,
fVCM= 50Hz,
100Hz
• Gain=64
VOFS
TGSW
dG/dT
Input offset volt‐
age
—
—
0.2
TBD
10
mV
µs
Gain=1, ADC
Averaging=32
Gain switching
settling time
TBD
3
Gain drift over
temperature
• Gain=1
• Gain=64
—
—
—
TBD
TBD
TBD
TBD
TBD
TBD
ppm/°C
ppm/°C
0 to 50°C
dVOFS/dT Offset drift over
temperature
Gain=1
ppm/°C 0 to 50°C, ADC
Averaging=32
dG/dVDDA Gain drift over
supply voltage
• Gain=1
• Gain=64
—
—
TBD
TBD
TBD
TBD
%/V
%/V
VDDA from 1.71
to 3.6V
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
39
Peripheral operating requirements and behaviors
Table 26. 16-bit ADC with PGA characteristics (continued)
Typ.1
Symbol
Description
Conditions
Min.
Max.
Unit
Notes
EIL
Input leakage er‐ All modes
ror
IIn × RAS
mV
IIn = leakage
current
(refer to the
MCU's voltage
and current op‐
erating ratings)
VPP,DIFF
Maximum differ‐
ential input signal
swing
[(VREFPGA × 2.33) - 0.2] / (2 ×
Gain)
V
4
SNR
THD
Signal-to-noise
ratio
• Gain=1
• Gain=64
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
D
TBD
TBD
TBD
TBD
TBD
TBD
TBD
8.3
57.7
87.3
85.3
92.42
2.54
13
12.7
8.4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
dB
dB
Average=32
Total harmonic
distortion
• Gain=1
• Gain=64
dB
Average=32,
fin=100Hz
dB
SFDR
ENOB
Spurious free dy‐
namic range
• Gain=1
• Gain=64
dB
Average=32,
fin=100Hz
dB
Effective number
of bits
• Gain=1, Average=4
• Gain=1, Average=8
• Gain=64, Average=4
• Gain=64, Average=8
• Gain=1, Average=2
• Gain=2, Avere=32
• Gain=4, Average=
• Gain=8rage=32
• Gan=16, age=32
Gai32, Average=32
Gain=64, Average=32
bits
bits
bits
bits
bits
bits
bits
bits
bits
bits
bits
8.7
13.4
13.1
12.6
11.8
11.1
10.2
9.3
SINAD
Signal-to-noise
plus distortion ra‐
tio
SENOB
6.02 × ENOB + 1.76
dB
1. Typical values assume VDDA =3.0V, Temp=25°C, fADCK=6MHz unless otherwise stated.
2.
Gain = 2PGAGx
3. When the PGA gain is changed, it takes some time to settle the output for the ADC to work properly. During a gain
switching, a few ADC outputs should be discarded (minimum two data samples, may be more depending on ADC
sampling rate and time of the switching).
4. Limit the input signal swing so that the PGA does not saturate during operation. Input signal swing is dependent on the
PGA reference voltage and gain setting.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
40
Freescale Semiconductor, Inc.
Preliminary
Peripheral operating requirements and behaviors
6.6.2 CMP and 6-bit DAC electrical specifications
Table 27. Comparator and 6-bit DAC electrical specifications
Symbol
Description
Min.
Typ.
Max.
Unit
VDD
Supply voltage
1.71
—
3.6
V
IDDHS
Supply current, High-speed mode (EN=1, PMODE=1,
—
—
200
μA
VDDA >= VLVI_trip
)
IDDLS
IDDOFF
VAIN
VAIO
VH
Supply current, low-speed mode (EN=1, PMODE=0)
Supply current, OFF Mode (EN=0,)
Analog input voltage
—
—
—
—
—
—
20
100
VD
μA
nA
V
VSS – 0.3
—
Analog input offset voltage
mV
Analog comparator hysteresis
• HYSTCTR = 00
—
—
—
—
5
—
—
—
—
mV
mV
mV
mV
• HYSTCTR = 01
20
30
• HYSTCTR = 10
• HYSTCTR = 11
VCMPOh
VCMPOl
tDHS
Output high
Output low
VDD – 5
—
—
50
—
0.5
120
V
V
Propagation delay, high-speed mode (EN=1,
PMODE=1)
20
ns
tDLS
Propagation delay, low-speed mode (EN1,
PMODE=1)
120
250
420
ns
Analog comparator initialization
6-bit DAC current adder (enbled)
6-bit DAC integraneari
6-bit DAC differeon-linearity
—
—
—
—
—
—
TBD
8
ns
IDAC6b
INL
μA
LSB1
LSB
–0.5
–0.3
0.5
0.3
DNL
1. 1 LSB = Vreference/64
6.6.3 12-bit DAC electrical characteristics
6.6.3.1 12-bit DAC operating requirements
Table 28. 12-bit DAC operating requirements
Symbol
Desciption
Min.
Max.
Unit
Notes
VDDA
Supply voltage
1.71
3.6
V
VDACR
TA
Reference voltage
Temperature
1.15
−40
3.6
V
1
105
°C
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
41
Peripheral operating requirements and behaviors
Table 28. 12-bit DAC operating requirements (continued)
Symbol
Desciption
Min.
Max.
Unit
Notes
CL
Output load capacitance
—
100
pF
2
IL
Output load current
—
1
mA
1. The DAC reference can be selected to be VDDA or the voltage output of the VREF module (VREFO)
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC
6.6.3.2 12-bit DAC operating behaviors
Table 29. 12-bit DAC operating behaviors
Symbol Description
Resolution
Min.
12
Typ.
—
Max.
12
Uit
b
Notes
n
IDDA_DACLP Supply current — low-power mode
—
—
150
μA
IDDA_DACH Supply current — high-speed mode
—
—
μA
P
tDACLP
Full-scale settling time (0x080 to 0xF7F) — low-
power mode
—
—
1
00
15
200
30
μs
μs
1
1
1
1
tDACHP
Full-scale settling time (0x080 to 0xF7F) — high-
power mode
tCCDACLP Code-to-code settling time (0xBF8 to 0xC08) —
low-power mode
—
5
μs
tCCDACHP Code-to-code settling time (0xBF8 to 0C08)
high-speed mode
TBD
100
—
—
μs
Vdacoutl
DAC output voltage range low — hipeed
mode, no load, DAC set to 0x000
0
—
mV
mV
Vdacouth DAC output voltage range hig— hi-seed
mode, no load, DAC t to 0FF
VDACR
−100
VDACR
INL
DNL
DNL
Integral non-line— high speed mode
Differential non-lineerror — VDACR > 2 V
3
—
—
—
8
1
1
LSB
LSB
LSB
2
3
4
0.5
0.5
Differential non-linearity rror — VDACR = VRE‐
FO (1.15 V)
VOFFSET Offset error
0.4
0.1
60
—
—
—
0.8
0.6
90
—
%FSR
%FSR
dB
5
5
EG
PSRR
TCO
Gain error
Power supply rejection ratio, VDDA > = 2.4 V
Temperature coefficient offset voltage
Temperature coefficient gain error
TBD
TBD
μV/C
TGE
—
—
ppm of
FSR/C
AC
Offset aging coefficient
—
—
—
—
TBD
250
μV/yr
Ω
Rop
Output resistance load = 3 kΩ
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
42
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 29. 12-bit DAC operating behaviors (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
SR
Slew rate -80h→ F7Fh→ 80h
• High power (SPHP
• Low power (SPLP
V/μs
)
1.2
1.7
—
—
0.05
0.12
)
CT
Channel to channel cross talk
3dB bandwidth
—
—
-80
dB
BW
kHz
• High power (SPHP
• Low power (SPLP
)
550
40
—
—
—
—
)
1. Settling within 1 LSB
2. The INL is measured for 0+100mV to VDACR−100 mV
3. The DNL is measured for 0+100 mV to VDACR−100 mV
4. The DNL is measured for 0+100mV to VDACR−100 mV with VDDA > 2.4V
5. Calculated by a best fit curve from VSS+100 mV to VREF−100 mV
Figure 13. Typical INL error vs. digital code
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
43
Peripheral operating requirements and behaviors
Figure 14. Offset half scale vs. temperature
6.6.4 Voltage RefeencElectrical Specifications
Tabl0. VREF full-range operating requirements
Symbol
Description
Min.
Max.
Unit
Notes
VDDA
Supply voltage
1.71
3.6
V
TA
CL
Temperature
−40
—
105
100
°C
nF
Output load capacitance
Table 31. VREF full-range operating behaviors
Symbol Description
Min.
Typ.
Max.
Unit
Notes
Vout
Vout
Vdrift
Voltage reference output with factory trim
TBD
1.2
TBD
V
V
Voltage reference output without factory trim
1.15
—
—
—
1.24
7
Temperature drift (Vmax -Vmin across the full
temperature range)
mV
See Fig‐
ure 15
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
44
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 31. VREF full-range operating behaviors (continued)
Symbol Description
Min.
Typ.
Max.
Unit
Notes
Tc
Ac
Ioff
Temperature coefficient
—
—
TBD
ppm/°C
Aging coefficient
—
—
—
—
TBD
0.10
ppm/year
µA
Powered down current (off mode, VREFEN = 0,
VRSTEN = 0)
Ibg
Itr
Bandgap only (MODE_LV = 00) current
Tight-regulation buffer (MODE_LV =10) current
Load regulation (MODE_LV = 10) current
Buffer startup time
—
—
TBD
—
75
µA
mA
1.1
—
—
100
TBD
TBD
TBD
µV/mA
s
Tstup
DC
100
—
—
Line regulation (power supply rejection)
—
–60
—
dB
Table 32. VREF limited-range operating requients
Symbol
Description
Mi
Max.
Unit
Notes
Notes
TA
Temperature
0
50
°C
Table 33. VREF limited-ranopeating behaviors
Symbol
Description
Min.
Max.
Unit
Vout
Voltage reference output with factory m
TBD
TBD
µA
TBD
ure 15. Typical output vs.temperature
Figure 16. Typical output vs. VDD
TBD
6.7 Timers
See General Switching Specifications.
6.8 Communication interfaces
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
45
Preliminary
Peripheral operating requirements and behaviors
6.8.1 DSPI Switching Specifications for Low-speed Operation
The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The tables
below provides DSPI timing characteristics for classic SPI timing modes. Refer to the
DSPI chapter of the Reference Manual for information on the modified transfer formats
used for communicating with slower peripheral devices.
Table 34. Master Mode DSPI Timing (Low-speed mode)
Num
Description
Min.
1.71
Max.
3.6
Un
V
Notes
Operating voltage
1
Frequency of operation
—
12.5
—
MHz
ns
DS1
DS2
DS3
DS4
DS5
DS6
DS7
DS8
DSPI_SCK output cycle time
4 x tBCLK
DSPI_SCK output high/low time
DSPI_PCSn to DSPI_SCK output valid
DSPI_SCK to DSPI_PCSn output hold
DSPI_SCK to DSPI_SOUT valid
DSPI_SCK to DSPI_SOUT invalid
DSPI_SIN to DSPI_SCK input setup
DSPI_SCK to DSPI_SIN input hold
(tSCK/2) - (tSCK/4
ns
ns
ns
ns
ns
ns
ns
SCK/2) 4
—
—
10
—
—
—
(tSCK) - 4
—
-2
15
0
1. The DSPI module can operate across the enterativoltage for the processor, but to run across the full voltage
range the maximum frequency of operation uced.
DSPI_PCSn
DS1
DS3
DS2
DS4
DSPI_SCK
(CPOL=0)
DS8
DS7
Data
Last data
First data
DSPI_SIN
DS5
DS6
First data
Data
Last data
DSPI_SOUT
Figure 17. DSPI Classic SPI Timing — Master Mode
Table 35. Slave Mode DSPI Timing (Low-speed Mode)
Num
Description
Min.
1.71
—
Max.
3.6
Unit
V
Operating voltage
Frequency of operation
6.25
MHz
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
46
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
Table 35. Slave Mode DSPI Timing (Low-speed Mode) (continued)
Num
Description
DSPI_SCK input cycle time
Min.
Max.
Unit
DS9
8 x tBCLK
—
ns
DS10
DS11
DS12
DS13
DS14
DS15
DS16
DSPI_SCK input high/low time
(tSCK/2) - 4
(tSCK/2) + 4
ns
ns
ns
ns
ns
ns
ns
DSPI_SCK to DSPI_SOUT valid
—
0
20
—
—
—
15
15
DSPI_SCK to DSPI_SOUT invalid
DSPI_SIN to DSPI_SCK input setup
DSPI_SCK to DSIP_SIN input hold
DSPI_SS active to DSPI_SOUT driven
DSPI_SS inactive to DSPI_SOUT not driven
5
15
—
—
DSPI_SS
DS10
S9
DSPI_SCK
(CPOL=0)
DS15
DS12
DS16
DS11
First data
DS14
Last data
DSPI_SOUT
ata
Data
DS13
First d
Last data
DSPI_SIN
Figure 18. DSlassic SPI Timing — Slave Mode
6.8.2 DSPI Switcg Specifications (High-speed mode)
The DMA Serial PeripherInterface (DSPI) provides a synchronous serial bus with
master and slave operations. Many of the transfer attributes are programmable. The tables
below provide DSPI timing characteristics for classic SPI timing modes. Refer to the
DSPI chapter of the Reference Manual for information on the modified transfer formats
used for communicating with slower peripheral devices.
Table 36. Master Mode DSPI Timing (High-speed mode)
Num
Description
Min.
2.7
Max.
3.6
25
Unit
V
Operating voltage
Frequency of operation
—
MHz
ns
DS1
DS2
DSPI_SCK output cycle time
2 x tBCLK
—
DSPI_SCK output high/low time
(tSCK/2) − 2
(tSCK/2) + 2
ns
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
47
Peripheral operating requirements and behaviors
Table 36. Master Mode DSPI Timing (High-speed mode) (continued)
Num
Description
Min.
Max.
Unit
DS3
DSPI_PCSn to DSPI_SCK output valid
(tSCK/2) − 2
—
ns
DS4
DS5
DS6
DS7
DS8
DSPI_SCK to DSPI_PCSn output hold
DSPI_SCK to DSPI_SOUT valid
DSPI_SCK to DSPI_SOUT invalid
DSPI_SIN to DSPI_SCK input setup
DSPI_SCK to DSPI_SIN input hold
(tSCK/2) − 2
—
8.5
—
ns
ns
ns
ns
ns
—
−2
TBD
0
—
—
DSPI_PCSn
DS1
DS3
DS2
DS4
DSPI_SCK
(CPOL=0)
DS8
DS7
Data
Last dat
First data
DSPI_SIN
DS5
DS6
First data
Data
data
DSPI_SOUT
Figure 19. DSPI Classic SI Timng — Master Mode
Table 37. Slave ModDSI Timing (High-speed mode)
Num
Description
Min.
Max.
3.6
Unit
V
Operating voltage
2.7
Frequency of operation
12.5
—
MHz
ns
DS9
DSPI_SCK inptime
4 x tBCLK
DS10
DS11
DS12
DS13
DS14
DS15
DS16
DSPI_SCK inp/low time
(tSCK/2) − 2
(tSCK/2 + 2
ns
ns
ns
ns
ns
ns
ns
DSPI_SCK to DSPIOUT valid
DSPI_SCK to DSPI_SOUT invalid
DSPI_SIN to DSPI_SCK input setup
DSPI_SCK to DSIP_SIN input hold
DSPI_SS active to DSPI_SOUT driven
DSPI_SS inactive to DSPI_SOUT not driven
—
0
TBD
—
2
—
7
—
—
—
14
14
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
48
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
DSPI_SS
DS10
DS9
DSPI_SCK
(CPOL=0)
DS15
DS12
DS16
DS11
First data
DS14
Last data
Last data
DSPI_SOUT
Data
Data
DS13
First data
DSPI_SIN
Figure 20. DSPI Classic SPI Timing — Slave Mode
6.8.3 SDHC Specifications
The following timing specs are defined at the chip I/O piand must be translated
appropriately to arrive at timing specs/constraints for te physical interface.
Table 38. SDHC switchng secifications
Num
Symbol
Description
Min.
Max.
Unit
Card nput ock
SD1
fpp
fpp
fpp
fOD
tWL
tWH
tTLH
tTHL
Clock frequency (low spee
Clock frequency (SO full peed)
Clock frequenc(Mfulpeed)
Clock equen(identification mode)
ime
0
0
400
25
20
400
—
—
3
kHz
MHz
MHz
kHz
ns
0
0
SD2
SD3
SD4
SD5
7
Clocgh time
7
ns
Clock rise time
—
—
ns
Clock fall time
3
ns
SDHC output / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
tOD SDHC output delay (output valid) -5 6.5
SDHC input / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
SD6
ns
SD7
SD8
tTHL
tTHL
SDHC input setup time
SDHC input hold time
5
0
—
—
ns
ns
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
49
Peripheral operating requirements and behaviors
SD3
SD2
SD1
SDHC_CLK
SD6
Output SDHC_CMD
Output SDHC_DAT[3:0]
Input SDHC_CMD
Input SDHC_DAT[3:0]
SD7
SD8
Figure 21. SDHC timing
I2S Switching Specifications
6.8.4
This section provides the AC timings for the I2S n master (clocks driven) and slave
modes (clocks input). All timings are given for non-inverted serial clock polarity
(TCR[TSCKP] = 0, RCR[RSCKP] = 0) and a on-inverted frame sync (TCR[TFSI] = 0,
RCR[RFSI] = 0). If the polarity of the clock and/or the frame sync have been inverted, all
the timings remain valid by inverting the lock signal (I2S_BCLK) and/or the frame sync
(I2S_FS) shown in the figures bel
I2S master mode timing
Tae 39.
Num
Description
Min.
Max.
Unit
V
Operating volta
I2S_MCLK cycle tim
2.7
2 x tSYS
45%
5 x tSYS
45%
—
3.6
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
ns
I2S_MCLK pulse width high/low
I2S_BCLK cycle time
55%
—
MCLK period
ns
I2S_BCLK pulse width high/low
I2S_BCLK to I2S_FS output valid
I2S_BCLK to I2S_FS output invalid
I2S_BCLK to I2S_TXD valid
55%
15
BCLK period
ns
ns
ns
ns
ns
ns
-2.5
—
—
15
I2S_BCLK to I2S_TXD invalid
-3
—
I2S_RXD/I2S_FS input setup before I2S_BCLK
I2S_RXD/I2S_FS input hold after I2S_BCLK
20
—
0
—
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
50
Freescale Semiconductor, Inc.
Peripheral operating requirements and behaviors
S1
S2
S2
I2S_MCLK (output)
I2S_BCLK (output)
I2S_FS (output)
I2S_FS (input)
I2S_TXD
S3
S4
S4
S5
S6
S10
S9
S7
S8
S7
S8
S9
S10
I2S_RXD
Figure 22. I2S timing — master mode
Table 40.
I2S alave mode tiing
Num
Description
Min.
Max.
3.6
Unit
V
Operating voltage
2.7
S11
S12
S13
S14
S15
S16
S17
S18
I2S_BCLK cycle time (input)
8 x tSYS
—
ns
I2S_BCLK pulse width high/low (input)
I2S_FS input setup before I2S_BCL
I2S_FS input hold after I2S_BCLK
I2S_BCLK to I2S_TXD/I2S_FS t valid
I2S_BCLK to I2S_TXD/I2SFS opunvalid
I2S_RXD setup I2SCLK
I2S_RXD holS_BCLK
45%
10
3
55%
—
MCLK period
ns
ns
ns
ns
ns
ns
—
—
0
20
—
10
2
—
—
S11
S12
I2S_BCLK (input)
I2S_FS (output)
I2S_FS (input)
I2S_TXD
S12
S15
S16
S13
S14
S15
S16
S15
S16
S17
S18
I2S_RXD
Figure 23. I2S timing — slave modes
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
51
Peripheral operating requirements and behaviors
6.9 Human-machine interfaces (HMI)
6.9.1 General Switching Specifications
These general purpose specifications apply to all signals configured for GPIO, SCI,
FlexCAN, CMT, and I2C signals.
Table 41. General switching specifications
Symbol
Description
Min.
Max.
Un
Notes
GPIO pin interrupt pulse width (digital glitch filter disa‐
bled) — Synchronous path
1.5
—
Bus cloc
cycles
1
GPIO pin interrupt pulse width (digital glitch filter disa‐
bled, analog filter enabled) — Asynchronous path
100
16
—
—
ns
2
2
GPIO pin interrupt pulse width (digital glitch filter disa‐
bled, analog filter disabled) — Asynchronous path
ns
External reset pulse width (digital glitch filter disabled)
TD
2
—
—
Mode select (EZP_CS) hold time after reset deasser‐
tion
Bus clock
cycles
Port rise and fall time (high drive strength
• Slew disabled
3
4
—
—
12
36
ns
ns
• Slew enabled
Port rise and fall time (low drive h)
• Slew disabled
—
—
32
36
ns
ns
• Slew enable
1. The greater synchronous annchronous timing must be met.
2. This is the shortest pulse that iuaranteed to be recognized.
3. 75pF load
4. 15pF load
6.9.2 TSI Electrical Specifications
Table 42. Touch Sensing Input module specifications
Symbol Description
VDDTSI Operating voltage
CELE
Min.
Typ.
Max.
Unit
Notes
1.71
—
3.6
V
Target electrode capacitance range
Reference oscillator frequency
1
20
500
pF
1
fREFmax
—
5.5
TBD
MHz
Table continues on the next page...
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
52
Freescale Semiconductor, Inc.
Dimensions
Notes
Table 42. Touch Sensing Input module specifications (continued)
Symbol Description
fELEmax Electrode oscillator frequency
CREF
VDELTA
IREF
Min.
Typ.
Max.
Unit
—
0.5
TBD
MHz
Internal reference capacitor
TBD
TBD
TBD
TBD
—
1
600
1
TBD
TBD
TBD
TBD
TBD
TBD
TBD
6
pF
mV
μA
μA
%
Oscillator delta voltage
Reference oscillator current source base current
Electrode oscillator current source base current
Electrode capacitance measurement precision
Electrode capacitance measurement precision
2
3
4
5
6
7
IELE
1
Pres5
Pres20
TBD
TBD
TBD
0.326
—
%
Pres100 Electrode capacitance measurement precision
—
Max‐
Max sensitivity @ 20pF electrode
0.15
fF
Sens20
MaxSens Maximum sensitivity
0.006
—
0.326
—
6
fF
bits
μs
8
9
Res
Resolution
TCon20
Response time @ 20pF
—
30
—
ITSI_RUN Current added in run mode
ITSI_LP Low power mode current adder
—
TB
1
—
μA
μA
—
TBD
1. The TSI module is functional with capacitance values outsidof thrange. However, optimal performance is not
guaranteed.
2. The programmable current source value is geneted bmultiping the SCANC[REFCHRG] value and the base current
3. The programmable current source value is generad by ltiplying the SCANC[EXTCHRG] value and the base current
4. Measured with a 5pF electrode, reference oscillator fquency of 10MHz, PS = 128, NCSC = 8; Iext = 16
5. Measured with a 20pF electrode, reference oor freuency of 10MHz, PS = 128, NCSC = 2; Iext = 16
6. Measured with a 20pF electrode, reference ator frequency of 10MHz, PS = 16, NCSC = 3; Iext = 16
7. 6.2ms scan time
8. 1pF electrode capacitance with 4.96mcan time
9. Time that takes to do one comearement of the electrode. Sensitivity resolution of 0.0133pF
7 Dimensions
7.1 Obtaining package dimensions
Package dimensions are provided in package drawings.
To find a package drawing, go to www.freescale.com and perform a keyword search for
the drawing’s document number:
If you want the drawing for this package
80-pin LQFP
Then use this document number
98ASS23174W
81-pin MAPBGA
98ASH98051A
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
53
Pinout
8 Pinout
8.1 K10 Signal Multiplexing and Pin Assignments
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The Port Control Module is responsible
for selecting which ALT functionality is available on each pin.
80
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
T7
EzPort
QFP
1
2
3
ADC1_SE4a
ADC1_SE5a
ADC1_SE6a
ADC1_SE4a
ADC1_SE5a
ADC1_SE6a
PTE0
SPI1_PCS1
SPI1_SOUT
SPI1_SCK
UART1_TX
UART1_RX
SDHC0_D1
SDHC0_D0
I2C1_S
I2SCL
PTE1
PTE2
UART1_CTS_ SDHC0_DCLK
b
4
ADC1_SE7a
ADC1_SE7a
PTE3
SPI1_SIN
UART1_RTS_ SDHC0CMD
b
5
6
DISABLED
DISABLED
VDD
PTE4
PTE5
SPI1_PCS0
SPI1_PCS2
UART3_TX
UART3_RX
SDHC0_D3
SHC0_D
7
VDD
8
VSS
VSS
9
ADC0_SE4a
ADC0_SE5a
ADC0_SE6a
ADC0_SE4a
ADC0_SE5a
ADC0_SE6a
PTE16
PTE17
PTE18
SPI0_PCS0
SPI0_SCK
SPI0_
UART2_
UA2_RX
FTM_CLKIN0
FTM_CLKIN1
FTM0_FLT3
LPT00_ALT3
10
11
UART2_CTS_ I2C0_SDA
12
13
ADC0_SE7a
ADC0_SE7a
PTE19
PI0_SIN
UART2_RTS_ I2C0_SCL
b
PGA0_DP/
ADC0_DP0/
ADC1_DP3
PGA0_DP/
ADC0_DP0/
ADC1_DP3
14
15
16
PGA0_DM/
ADC0_DM0/
ADC1_DM3
PGA0_DM/
ADC0_DM0/
ADC1_DM3
PGA1_DP/
ADC1_DP0/
ADC0_DP3
PGA1_DP/
ADC1_DP0/
ADC0_DP3
PGA1_DM/
ADC1_DM0/
ADC0_DM3
PGA1_DM/
ADC1_DM0/
ADC0_DM3
17
18
19
20
21
22
VDDA
VDDA
VREFH
VREFH
VREFL
VREFL
VSSA
VSSA
VREF_OUT
DAC0_OUT
VREF_OUT
DAC0_OUT
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
54
Freescale Semiconductor, Inc.
Pinout
80
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
QFP
23
24
25
26
XTAL32
XTAL32
EXTAL32
VBAT
EXTAL32
VBAT
JTAG_TCLK/
SWD_CLK/
EZP_CLK
TSI0_CH1
PTA0
UART0_CTS_ FTM0_CH5
b
JTAG_TCLK/
SWD_CLK
EZP_CLK
27
28
JTAG_TDI/
EZP_DI
TSI0_CH2
TSI0_CH3
PTA1
PTA2
UART0_RX
UART0_TX
FTM0_CH6
FTM0_CH7
JTAG_TDI
EZP_DI
JTAG_TDO/
TRACE_SWO/
EZP_DO
JTG_TDO/
TRE_SWO
EZP_DO
29
30
31
32
33
34
JTAG_TMS/
SWD_DIO
TSI0_CH4
TSI0_CH5
PTA3
UART0_RTS_ FTM0_CH0
b
JTAGS/
SWD_D
NMI_b/
EZP_CS_b
PTA4
FTM0_CH1
NMI_b
EZP_CS_b
JTAG_TRST
CMP2_IN0
CMP2_IN1
DISABLED
PTA5
FTM0_CH2
CMUT
RX_BCL JTAG_TRST
K
CMP2_IN0
CMP2_IN1
PTA12
PTA13
PTA14
CAN0_TX
CAN0_RX
SPI0_PCS0
FTM1_CH0
FTM1_CH1
UART0_T
UART0
I2S0_TXD
FTM1_QD_PH
A
I2S0_TX_FS
FTM1_QD_PH
B
I2S0_TX_BCL
K
35
36
DISABLED
DISABLED
PTA15
PTA16
SPI0_SCK
I2S0_RXD
SPI0_SOUT
UA0_CTS_
b
I2S0_RX_FS
37
ADC1_SE17
ADC1_SE17
PTA17
SPI0_
RT0_RTS_
b
I2S0_MCLK
LPT0_ALT1
I2S0_CLKIN
38
39
40
41
42
43
VDD
VDD
VSS
VSS
EXTAL
XTAL
EXTAL
XTAL
PT
PTA19
FTM0_FLT2
FTM1_FLT0
FTM_CLKIN0
FTM_CLKIN1
RESET_b
RESET_b
ADC0_SE8/
ADC1_SE8/
TSI0_CH0
ADC0_SE8/
ADC1_SE8/
TSI0_CH0
PTB0
PTB1
I2C0_SCL
I2C0_SDA
FTM1_CH0
FTM1_CH1
FTM1_QD_PH
A
44
ADC0_SE9/
ADC1_SE9/
TSI0_CH6
ADC0_SE9/
ADC1_SE9/
TSI0_CH6
FTM1_QD_PH
B
45
46
ADC0_SE12/
TSI0_CH7
ADC0_SE12/
TSI0_CH7
PTB2
PTB3
I2C0_SCL
I2C0_SDA
UART0_RTS_
b
FTM0_FLT3
FTM0_FLT0
ADC0_SE13/
TSI0_CH8
ADC0_SE13/
TSI0_CH8
UART0_CTS_
b
47
48
49
50
ADC1_SE14
ADC1_SE15
VSS
ADC1_SE14
ADC1_SE15
VSS
PTB10
PTB11
SPI1_PCS0
SPI1_SCK
UART3_RX
UART3_TX
FB_AD19
FB_AD18
FTM0_FLT1
FTM0_FLT2
VDD
VDD
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
55
Pinout
80
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
QFP
51
52
53
TSI0_CH9
TSI0_CH10
TSI0_CH11
TSI0_CH9
TSI0_CH10
TSI0_CH11
PTB16
SPI1_SOUT
SPI1_SIN
CAN0_TX
UART0_RX
UART0_TX
FTM2_CH0
FB_AD17
FB_AD16
EWM_IN
PTB17
PTB18
EWM_OUT_b
I2S0_TX_BCL FB_AD15
K
FTM2_QD_PH
A
54
55
56
57
TSI0_CH12
TSI0_CH12
PTB19
PTC0
PTC1
PTC2
CAN0_RX
FTM2_CH1
I2S0_TX_FS
FB_OE_b
FB_AD14
FB_AD13
FB_AD12
FTM2_QD_PH
B
ADC0_SE14/
TSI0_CH13
ADC0_SE14/
TSI0_CH13
SPI0_PCS4
SPI0_PCS3
SPI0_PCS2
PDB0_EXTRG I2S0_TXD
ADC0_SE15/
TSI0_CH14
ADC0_SE15/
TSI0_CH14
UART1_RTS_ FTM0_CH0
b
ADC0_SE4b/
CMP1_IN0/
TSI0_CH15
ADC0_SE4b/
CMP1_IN0/
TSI0_CH15
UART1_CTS_ FTM0_CH1
b
58
59
60
61
62
63
64
65
CMP1_IN1
VSS
CMP1_IN1
VSS
PTC3
SPI0_PCS1
UART1_RX
FTM0_CH2
FB_CLKOUT
VDD
VDD
DISABLED
DISABLED
CMP0_IN0
CMP0_IN1
PTC4
PTC5
PTC6
PTC7
PTC8
SPI0_PCS0
SPI0_SCK
SPI0_SOUT
SPI0_SIN
UART1_TX
FTM0_H3
LPT0_ALT2
AD11
FB_A0
_AD9
FB_AD8
FB_AD7
CMP1_OUT
CMP0_OUT
CMP0_IN0
CMP0_IN1
PDB0_EXTRG
I2S0_MCL
ADC1_SE4b/
CMP0_IN2
ADC1_SE4b/
CMP0_IN2
I2S0_KIN
66
67
ADC1_SE5b/
CMP0_IN3
ADC1_SE5b/
CMP0_IN3
PTC9
I2S0_RX_BCL FB_AD6
K
FTM2_FLT0
ADC1_SE6b/
CMP0_IN4
ADC1_SE6b/
CMP0_IN4
PTC10
PTC11
I2C1_S
C1_SDA
I2S0_RX_FS
FB_AD5
68
69
70
71
ADC1_SE7b
VSS
ADC1_SE7b
VSS
I2S0_RXD
FB_RW_b
VDD
VDD
DISABLED
PTC
PTC17
CAN1_RX
CAN1_TX
UART3_RX
UART3_TX
FB_CS5_b/
FB_TSIZ1/
FB_BE23_16_
BLS15_8_b
72
DISABLED
FB_CS4_b/
FB_TSIZ0/
FB_BE31_24_
BLS7_0_b
73
74
DISABLED
PTD0
PTD1
SPI0_PCS0
SPI0_SCK
UART2_RTS_
b
FB_ALE/
FB_CS1_b/
FB_TS_b
ADC0_SE5b
ADC0_SE5b
UART2_CTS_
b
FB_CS0_b
75
76
77
DISABLED
DISABLED
DISABLED
PTD2
PTD3
PTD4
SPI0_SOUT
SPI0_SIN
UART2_RX
UART2_TX
FB_AD4
FB_AD3
FB_AD2
SPI0_PCS1
UART0_RTS_ FTM0_CH4
b
EWM_IN
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
56
Freescale Semiconductor, Inc.
Pinout
80
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
QFP
78
ADC0_SE6b
ADC0_SE6b
ADC0_SE7b
PTD5
SPI0_PCS2
UART0_CTS_ FTM0_CH5
b
FB_AD1
EWM_OUT_b
79
80
ADC0_SE7b
DISABLED
PTD6
PTD7
SPI0_PCS3
CMT_IRO
UART0_RX
UART0_TX
FTM0_CH6
FTM0_CH7
FB_AD0
FTM0_FLT0
FTM0_FLT1
8.2 K10 Pinouts
The below figure shows the pinout diagram for the devices supported by this document.
Many signals may be multiplexed onto a single pin. To determine what sigals can be
used on which pin, see the previous section.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Freescale Semiconductor, Inc.
57
Preliminary
Revision History
1
PTE0
PTE1
PTE2
PTE3
PTE4
PTE5
VDD
60
59
58
57
56
5
52
51
50
49
48
47
46
45
44
43
42
41
VDD
2
VSS
3
PTC3
PTC2
PTC1
PTC0
PTB19
PTB18
PTB17
PTB16
VDD
4
5
6
7
8
VSS
9
PTE16
PTE17
PTE18
PTE19
10
11
12
13
14
15
16
17
18
19
20
VSS
PGA0_DP/ADC0_DP0/ADC1_DP3
PTB11
PTB10
PTB3
PTB2
PTB1
PTB0
RESET_b
PTA19
PGA0_DM/ADC0_DM0/ADC1_DM3
PGA1_DP/ADC1_DP0/ADC0_DP3
PGA1_DM/ADC1_DM0/ADC0_DM3
VDDA
VREFH
VREFL
VSSA
Figure 24. K10 80 LQFP Pinout Diagram
9 Revision History
The following table provides a revision history for this document.
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
58
Freescale Semiconductor, Inc.
Preliminary
Revision History
Table 43. Revision History
Rev. No.
Date
Substantial Changes
1
11/2010
Initial public revision
K10 Sub-Family Data Sheet Data Sheet, Rev. 1, 11/2010.
Preliminary
Freescale Semiconductor, Inc.
59
How to Reach Us:
Home Page:
www.freescale.com
Web Support:
http://www.freescale.com/support
USA/Europe or Locations Not Listed:
Freescale Semiconductor, Inc.
Technical Information Center, EL516
2100 East Elliot Road
Tempe, Arizona 85284
1-800-521-6274 or +1-480-768-2130
www.freescale.com/support
Information in this document is provided solely to enable system and
software implementers to use Freescale Semiconductor products. There are
no express or implied copyright licenses granted hereunder to design or
fabricate any integrated circuits or integrated circuits based on the
information in this document.
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
www.freescale.com/support
Freescale Semiconductor reserves the right to make changes out further
notice to any products herein. Freescale Semiconductor makes arranty,
representation or guarantee regarding the suitability of productany
particular purpose, nor does Freescale Semicondur ase any llity
arising out of the application or use of any product circspecifically
disclaims any and all liability, including without limitationtial or
incidental damages. “Typical” parameters tmay be in Freescale
Semiconductor data sheets and/or specatioan and vary in different
applications and actual performance my vary ovme. All operating
parameters, including “Tyals”, musvalidated each customer
application by customer’s techal expereescale Semiconductor does
not convey any license under its ent righor the rights of others.
Freescale Semiconductor products not designed, intended, or authorized
for use as componenn ms inted for surgical implant into the body,
or other applications ntendesupport or sustain life, or for any other
application in wfailure of Freescale Semiconductor product could
create a situan wheersonal injury or death may occur. Should Buyer
phase oFreescalemiconductor products for any such unintended
or unauthorizeplication, Buyer shall indemnify and hold Freescale
Semicuctor as officers, employees, subsidiaries, affiliates, and
istributoarmless against all claims, costs, damages, and expenses, and
onable ney fees arising out of, directly or indirectly, any claim of
peral injury or death associated with such unintended or unauthorized
use, eif such claim alleges that Freescale Semiconductor was negligent
regarding the design or manufacture of the part.
Japan:
Freescale Semiconductor Japan Ltd. Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064
Japan
0120 191014 or +81 3 5437 9125
support.japan@freescale.com
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
+86 10 5879 8000
support.asia@freescale.com
Freescale Semiconductor Literatuibutioenter
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447 or +1-303-675-2
Fax: +1-303-675-2150
Freescale™ and the Freescale logo are trademarks of Freescale
Semiconductor, Inc. ARM is the registered trademark of ARM Limited. ARM
Cortex-M4 is the trademark of ARM Limited. All other product or service
names are the property of their respective owners.
LDCForFreescaleSemiconductor@hibtgroup.com
© Freescale Semiconductor, Inc. 2010. All rights reserved.
K10P81M100SF2
Rev. 1
11/2010
相关型号:
©2020 ICPDF网 联系我们和版权申明