GMDW12V08PMR001L [GALAXY]
DORADO MV 24V or 48V Input, 8.0V, 12.0V DC, 8A Output 15.0V DC, 6A Output; DORADO MV 24V或48V输入， 8.0V ， 12.0V DC ， 8A输出15.0V DC， 6A输出
| 型号： | GMDW12V08PMR001L |
| 厂家： | 
GALAXY POWER, INC. |
| 描述： | DORADO MV 24V or 48V Input, 8.0V, 12.0V DC, 8A Output 15.0V DC, 6A Output |
| 文件： | 总7页 (文件大小：766K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
DORADO MV
24V or 48V Input,
8.0V, 12.0V DC, 8A Output
15.0V DC, 6A Output
Industry's Lowest Cost High-efficiency
DC/DC Converter
Industry Standard Quarter Brick Pinout and
Footprint
Typical Efficiency: 86% at 12V, 8A
Low Profile
Very Low Common-mode Noise for a
Commercial DC/DC Converter
Constant Switching Frequency
Remote Sense
Uses Innovative Control and Power Topology
for Lower Parts Count
Single Board Design
Optional Low Profile Heatsink for Improved
Thermal Performance
The Dorado MV is available with an optional
low profile heatsink for improved thermal
performance.
Header with M3 Metal Inserts for Mechanical
Connection to PCB
Two Year Warranty
Control Functions
Microprocessor Controlled
Primary-side Enable, Choice of Logic
Industry Standard Output Trim
Protection Features
Over Temperature Protection
Over Voltage Protection
Over Current Protection
Over/Under Input Voltage Protection
Typical Characteristics
Output Setpoint Accuracy: ±1%
Load Regulation: ±0.2%
Line Regulation: ±0.2%
Regulation over Line, Load, and Temperature: ±2%
Low Output Ripple
Dorado MV, Page 1
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
General Specifications
V
= 48V
T @25°C, 300 LFM Airflow, V
= 3.3V, I
= full load unless otherwise noted.
OUT
IN
DC,
A
OUT
Available output power depends on ambient temperature and good thermal management. (See application graphs for limits.)
Input Characteristics
Parameter
Min
Typ
Max
75
4
Units
Operating Input Voltage
Input Current
36
48
V
DC
A
Input Capacitance
Input Hysteresis, Low Line
2
2
µF
V
DC
Output Characteristics
Regulation Over Line, Load & Temperature
Voltage Ripple
98
0
102
20
%V
mV
NOM
RMS
Voltage Ripple, 20MHz BW
Current Range
100
8
mV
P–P
A
Output Transient Response, 50% to 75% load change, 1A/µsec
Settling Time to ±1%
5
%V
OUT
400
300
1
µS
mS
Turn-on Time to 98%Vnom
Output Overshoot at Turn-on
Trim Range
%V
OUT
OUT
OUT
60
110
%V
%V
Overvoltage Protection, Non-latching
130
300
Isolation
Isolation Test Voltage, Input/Output (Basic)
Isolation Resistance
2000
10
V
DC
MΩ
Features
Overtemperature Protection, Thermal Sensor, Non-latching*
Switching Frequency, Fixed
117
°C
kHz
*PCB less than 130°C
General Specifications
Approvals and Standards
Operating Temperature
Storage Temperature
Relative Humidity
-40°C to +100°C
-55°C to +125°C
UL and c-UL Recognized Component, TUV,
UL60950, CSA 22.2 No. 950, IEC/EN 60950**
EMC Characteristics:
10% to 95% RH,
Non-condensing
2 to 9Hz, 3mm disp.,
9 to 200Hz 1g
Designed to meet emission and immunity
requirements per EN55022, CISPR 22, Class B,
and CISPR 24.
Vibration
Material Flammability
Weight
UL V-0
30 grams
** An external fuse shall be used to comply with the
requirements.
MTBF
Telcordia (Bellcore)
2,000,000 hours
Dorado MV, Page 2
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
Application Notes
CoolConverter™
Galaxy’s proprietary CoolConverter™ provides:
• Patented single-stage power conversion architecture,
control, and magnetic design allow unprecedented power
density and efficiency in an isolated power supply.
• An advanced microcontroller reduces parts count while
adding features, performance, and flexibility in the design.
Overvoltage Lockout
Protection and Control
Valid Input Voltage Range:
The converter measures the input voltage and will not
allow operation outside of the input voltage
specification. As shown by the graphs, hysteresis is
added to both the high and low voltage to prevent the
converter from turning on and off repeatedly when the
voltage is held near either voltage extreme. At low line
this assures the maximum input current is not exceeded;
at high line this assures the semiconductor devices in
the converter are not damaged by excessive voltage
stress.
Voltage
Rising
Voltage
Falling
75
76
77
78
79
80
Input Voltage (V)
Undervoltage Lockout
ON/OFF Logic Option:
The ON/OFF control logic can be either Negative
(standard) or Positive to enable the converter. For
Negative logic, the ON/OFF pin is brought below 1.0V
with respect to the –INPUT pin to enable the converter.
For Positive logic, the ON/OFF pin is brought to greater
than 4.0V with respect to the –INPUT pin. To request
the Positive logic version, add the suffix (P) to the
standard part number. The Enable pin has a built-in pull
up resistor of approximately 100kΩ.
Voltage
Rising
Voltage
Falling
30
32
34
36
38
40
Input Voltage (V)
Dorado MV, Page 3
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
Application Notes
Output Over Voltage Protection:
Trim-down
The output voltage is constantly monitored by the
microprocessor and a redundant secondary-side circuit
that is set to a higher trip point than the microprocessor
protection. If the output voltage exceeds the over-
voltage specification, the microprocessor will restart
every 4 seconds and limit voltage with a separate
reference circuit. This advanced feature prevents the
converter from damaging the load if there is a converter
failure or application error.
Thermal Shutdown:
The printed circuit board temperature is measured
using a semiconductor sensor. If the maximum rated
temperature is exceeded, the converter is turned off. It
will then restart every 4 seconds.
Trim-down (%)
100
RTRIM-DOWN
=
– 2
5.11kΩ
{∆% }
Remote Sense:
Trim-up (for 3.3V)
The output voltage is regulated at the point where the
sense pins connect to the power output pins. Total sense
compensation should not exceed 1V.
Safety:
An external input fuse must always be used to meet
safety requirements.
Trim:
To trim the output voltage higher, connect the
required trim resistor from the Trim pin to the +Sense
pin. To trim the output voltage lower, connect the
required trim resistor from the Trim pin to the –Sense
pin. See following diagrams.
VO(100+∆%) (100+2∆%)
RTRIM-UP
=
–
5.11kΩ
{
}
1.225∆%
∆%
External Output Trimming
+ Sense
Trim
– Sense
Dorado MV, Page 4
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
GMDW12V08 Operation
Efficiency
Power Dissipation
89
87
85
83
81
79
77
75
18
16
14
12
10
8
6
36V Vin
48V Vin
75V Vin
36V Vin
48V Vin
75V Vin
4
2
0
6.0
0
8.0
2.0
4.0
6.0
0
2.0
4.0
8.0
Output Current (A)
Output Current (A)
Transient Response
Voltage Ripple
]
[
T
T
1
2
Ch2 100mV
M 1.00ms A Ch2
96.0mV
20.0mV
20.0mV
Ch1 200mV
Start-up
]
[
T
T
1
2
Ch2 5.00 V
M 20.0ms A Ch2
2.70V
Ch1 5.00V
Dorado MV, Page 5
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
PACKAGE DETAIL
2.28
MOUNTING INSERT
Pin
Function
Pin Dia. (in.)
CONNECTED TO CASE PIN
1
2
3
4
5
6
7
8
– Input
On/Off
+ Input
+ Output
+ Sense
Trim
0.040
0.040
0.040
0.060
0.040
0.040
0.040
0.060
1.030
1.030
B
A
A
PIN 1 .815
.815 PIN 8
.665 PIN 7
.515 PIN 6
.365 PIN 5
.215 PIN 4
A
1.45
PIN 2 .515
PIN 3 .215
0
0
BOTTOM VIEW
– Sense
– Output
.210
MOUNTING INSERT
M3 X 0.5 4 PLACES
.210
.070
2.000
PIN TO PIN
.20
0
Notes:
1. Mechanical tolerances
x.xxx in. = ±0.005 in.
x.xx in. = ±0.01 in.
2. Pin material: brass with tin/lead plating over nickel
3. Workmanship: Meets or exceeds IPC-A-610B Class II
.50
(opt. L = .465)
.030
.50
SIDE VIEW
Dorado MV, Page 6
Part No. 01-002 Rev. 1.0–110702
PRELIMINARY
ORDERING INFORMATION
Standard Model
Number
Output
Voltage
Max
Typical Efficiency
Half Load Full Load
Standard Model
Number
Output
Voltage
Max
Typical Efficiency
Half Load Full Load
Current
Current
24V Input Models (Designated C)
48V Input Models (Designated W)
GMDC8V08R
GMDC12V08R
GMDC15V06R
* Options:
8V
12V
15V
8A
8A
6A
TBD
TBD
TBD
GMDW8V08R
GMDW12V08R
GMDW15V06R
8V
12V
15V
8A
8A
6A
TBD
88
86
TBD
Heatsink Part Numbers
P = Positive Logic Version: High = On
M = 0.145" Pins (±.01")
S = 0.12" Pins (±.01")
R = Heatsink Ready
L = Low Profile (0.465" height)
Part
Typical Thermal Performance
Number
Height
Natural Convection
Power Dissipation*
Forced Convection
Thermal Resistance**
001
002
003
004
0.25"
0.50"
1.00"
0.13"
5W
7W
5.8°C/W
3.2°C/W
2.0°C/W
TBD
11W
TBD
*@ 60°C rise heatsink to ambient
** @ 300'/min.
Ordering Information
Example Part No:
GMDW12V08R
48V Input
12V@8A Output
Negative Logic
0.20" Pin Length
Heatsink Ready
Options Code:
GMDW12V08 P S R 00X L
Part No.
Options:
Positive Logic Version
Optional Pin Lengths
M = 0.145"
S = 0.12"
Heatsink Ready
Heatsink
Low Profile
Galaxy Power Inc. warrants to the original purchaser that the products conform to this data sheet and are free from material
and workmanship defects for a period of two (2) years from the date of manufacture, if this product is used within specified
conditions. Galaxy Power Inc. reserves the right to make changes to the product(s) or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any
such products or information. For additional details on this limited warranty consult the factory.
155 Flanders Road Westborough, MA 01581
508-870-9775 Fax: 508-870-9796
e–mail: galaxy@galaxypwr.com
website: http://www.galaxypwr.com
Dorado MV, Page 7
Part No. 01-002 Rev. 1.0–110702
© Copyright 2002 Galaxy Power. Specifications subject to change without notice.
相关型号：
GMDW12V08PMR003L
DC-DC Regulated Power Supply Module, 1 Output, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
GMDW12V08PMR004L
DC-DC Regulated Power Supply Module, 1 Output, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
GMDW12V08PSR003L
DC-DC Regulated Power Supply Module, 1 Output, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
GMDW12V08PSR004L
DC-DC Regulated Power Supply Module, 1 Output, Hybrid, ROHS COMPLIANT PACKAGE-8
BEL
©2020 ICPDF网 联系我们和版权申明