GM66100-2.5TA3RG [GAMMA]
1.0A ULTRA LOW DROPOUT VOLTAGE REGULATORS; 1.0A超低压差稳压器型号: | GM66100-2.5TA3RG |
厂家: | GAMMA MICROELECTRONICS INC. |
描述: | 1.0A ULTRA LOW DROPOUT VOLTAGE REGULATORS |
文件: | 总12页 (文件大小:198K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Description
Features
The GM66100/1/2 series are 1A ultra low-dropout
linear voltage regulators that provide low-voltage,
high output current from an extremely small
package.
Fixed and adjustable output voltages
Typical 410mV Dropout Voltage @ 1A
1A minimum guaranteed output current
Accurate 1% Guaranteed Tolerance
Current limiting and thermal shutdown
Reverse-battery Protection
The GM66100/1/2 offers extremely low dropout
(typically 410 m V at 1A) and low ground current
(typically 12mA at 1A).
The GM66100 offers 3 Lead packages with a fixed
output voltage options while GM66101/2 offer SO8
packages for fixed and adjustable output voltages
accordingly.
Reversed leakage protection
Fast Transient Response
The GM66100/1/2 is ideal for PC add-in cards that
need to convert from standard 5V to 3.3V, 3.3V to
2.5V or 2.5V to 1.8V. A guaranteed maximum
dropout voltage of 630mV over all operating
conditions allows the GM66100/1/2 provide 2.5V
from a supply as low as 3.13V and 1.8V from a
supply as low as 2.43V.
The GM66100/1/2 is fully protected with over
current limiting, thermal shutdown, and reversed-
battery protection.
Application
High Efficiency Linear Regulators
Ideal for 3.0V to 2.5V conversion
Ideal for 2.5V to 1.8V conversion
Battery Powered Equipment
Automotive Electronics
Post Regulators for Switching Supplies
Typical Application Circuits
GM66100-2.5
GM66101-2.5
Enable
VIN
3.3V
Error Flag Output
Enable
Flag
VOUT
VOUT
2.5V
VIN
VOUT
Shutdown
Gnd
VIN
3.3V
10uF
VOUT
2.5V
VIN
Gnd
10uF
2.5V/1A Regulator
2.5V/1A Regulator with Error Flag
GM66102
Enable
Shutdown
VOUT
1.5V
Enable
VOUT
R1
VIN
Adj
Gnd
VIN
2.5V
10uF
R2
1.5V/1A Adjustable Regulator
www.gammamicro.com.tw
2
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Marking Information and Pin Configurations (Top View)
GM66100
TO 252
(D-PAK)
TO 263
TO 220
SOT223
(D2-PAK)
GM66100G
VVAYWW
GM66100G
VVAYWW
G: Green Product
VV: Fixed Output (15 = 1.5V, 25 = 3.3V…)
A: Assembly / Test site code
Y: Year
WW: Week
GM66101
SO8
EN
VIN
Gnd
Gnd
Gnd
Gnd
G: Green Product
VV: Fixed Output (15 = 1.5V, 25 = 3.3V…)
A: Assembly / Test site code
Y: Year
VOUT
Flag
WW: Week
GM66102
SO8
EN
VIN
Gnd
Gnd
Gnd
Gnd
G: Green Product
A: Assembly / Test site code
Y: Year
VOUT
Adj
WW: Week
3
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Ordering Information
Ordering Number
Output Voltage
Package
Shipping
GM66100
GM66100-1.8TA3RG
GM66100-1.8TB3TG
GM66100-1.8TC3TG
GM66100-1.8ST3RG
GM66100-2.5TA3RG
GM66100-2.5TB3TG
GM66100-2.5TC3RG
GM66100-2.5ST3RG
GM66100-3.3TA3RG
GM66100-3.3TB3TG
GM66100-3.3TC3TG
GM66100-3.3ST3RG
GM66100-5.0TA3RG
GM66100-5.0TB3TG
GM66100-5.0TC3RG
GM66100-5.0ST3RG
1.8V
1.8V
1.8V
1.8V
2.5V
2.5V
2.5V
2.5V
3.3V
3.3V
3.3V
3.3V
5.0V
5.0V
5.0V
5.0V
TO-263
TO-220
TO-252
SOT-223
TO-263
TO-220
TO-252
SOT223
TO-263
TO-220
TO-252
SOT-223
TO-263
TO-220
TO-252
SOT223
800 Units / Reel
50 Units/Tube
2,500 Units/Reel
2,500 Units/Reel
800 Units / Reel
50 Units/Tube
2,500 Units / Reel
2,500 Units / Reel
800 Units / Reel
50 Units/Tube
2,500 Units/Reel
2,500 Units/Reel
800 Units / Reel
50 Units/Tube
2,500 Units / Reel
2,500 Units / Reel
Ordering Information (continued)
Ordering Number
Output Voltage
Package
Shipping
GM66101
GM66101-1.8S8RG
GM66101-2.5S8RG
GM66101-3.3S8RG
1.8V
2.5V
3.3V
SOP-8
SOP-8
SOP-8
2,500 Units/Reel
2,500 Units/Reel
2,500 Units/Reel
Ordering Information (continued)
Ordering Number
Output Voltage
Package
Shipping
GM66102
GM66102S8RG
Adj
SOP-8
2,500 Units/Reel
4
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Absolute Maximum Ratings (Note 1)
Rating
Symbol
VIN
Value
-20 to +20
+20
Unit
V
Supply Voltage
Enable Voltage
Storage Temperature Range
VEN
V
TSTG
- 65 to 150
°C
Lead Temperature (Soldering, 10 sec)
ESD
+ 260
°C
Note 3
Operating Ratings (Note 2)
Rating
Symbol
VIN
Value
Unit
V
Supply Voltage
2.25 to 16
2.25 to 16
Enable Voltage
VEN
V
Maximum Power Dissipation
Junction Temperature Range
PD(MAX)
TJ
Note 4
-40 to 125
°C
SOT223
Package Thermal Resistances
SO8
15
20
°C/W
°C/W
θJC
5
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Block Diagram
VIN
VOUT
18V
1.24V
Ref
Thermal
Shut Down
Gnd
GM66100 Fixed Regulator Block Diagram
VIN
VOUT
18V
1.24V
FLAG
EN
Ref
Thermal
Shut Down
Gnd
GM66101 Fixed Regulator with Flag and Enable Block Diagram
VIN
VOUT
18V
1.24V
Ref
EN
Adj
Thermal
Shut Down
Gnd
GM66102 Adjustable Regulator with Enable Block Diagram
6
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Electrical Characteristics:
(VIN = VOUT + 1V, VEN = 2.25V,Unless otherwise specified: TJ = 25°C, Bold values are guaranteed across the full operating
temperature range)
Parameter
Condition
Symbol
Min
-1
Typ
Max
1
Unit
IO = 10mA
Output Voltage
VOUT
%
-2
-2
10mA < IO < 1A, VOUT + 1V < VIN < 8V
Line
Regulation
0.06
0.2
0.5
1.0
%
%
ΔVOI
ΔVOL
IO = 10mA, VOUT + 1V < VIN < 16V
VIN = VOUT + 1V, 10mA < IO < 1A
Load
Regulation
Output
Temperature
Coefficient
40
100
ppm/°C
ΔVOUT/ ΔT
Note 5
150
200
IO = 100mA, ΔVOI = -1%
250
Dropout
Voltage,
Note 6
275
330
410
IO = 500mA, ΔVOI = -1%
IO = 750mA, ΔVOI = -1%
VDO
mV
500
550
630
IO = 1A, ΔVOI = -1%
700
4
μA
mA
A
IO = 100mA, VIN = VOUT + 1V
IO = 500mA, VIN = VOUT + 1V
IO = 750mA, VIN = VOUT + 1V
IO = 1A, VIN = VOUT + 1V
Ground
Current
Note 7
IGND
7
12
1.8
20
ICL
2.5
Current Limit
Enable Input
Parameter
VOUT = 0V, VIN = VOUT + 1V
Condition
Symbol
VEN(low)
Min
Typ
Max
Unit
08
V
Logic low (OFF)
Logic High (ON)
Enable Input
Voltage
VEN(high)
2.25
1
15
30
75
2
IEN(low)
VEN = 2.25V
VEN = 0.8V
Enable Input
Current
μA
IEN(high)
4
7
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Flag Output
Parameter
Condition
Symbol
Min
Typ
Max
1
Unit
0.01
Output Leakage
Current
IFLG(leak)
μA
VOH = 16V
2
Output Low
Voltage
Note 8
240
300
400
VFLG (DO)
mV
%
VIN = 0.9V+VOUT Nominal, ICL=250μA
93
1
Low Threshold
High Threshold
Hysteresis
% of VOUT
% of VOUT
99.2
1
15
30
75
2
IEN(low)
Enable Input
Current
μA
IEN(high)
VEN = 0.8V
4
GM66102 Only
Parameter
Condition
Symbol
Min
1.228
1.215
1.203
Typ
Max
1.252
1.265
1.277
80
Unit
1.24
Reference
Voltage
VREF
V
Note 9
40
Adjust Pin Bias
Current
IADJ
μA
120
Reference
Voltage Temp
Coefficient
Note 5
Adjust Pin Bias
Current Temp
Coefficient
20
ppm/°C
nA/°C
ΔVREF/ ΔT
Δ IADJ / ΔT
0.1
99.2
Note 1: Exceeding the absolute maximum ratings may damage the device.
Note 2: The device is not guaranteed to function outside its operating rating.
Note 3: Devices are ESD sensitive. Handling precautions is recommended.
Note 4: PD(MAX) = (TJ(MAX) – TA)/θJA, where θJA is junction to ambient thermal resistance
Note 5: Output voltage temperature coefficient is ΔVOUT(worst case)/(TJ(MAX)-TJ(MIN)), where TJ(MAX) is 125°C and TJ(MIN) is
0°C
Note 6: VDO = VIN – VOUT when VOUT decreases to 99% of its nominal output voltage with VIN = VOUT + 1V. For output
voltage below 2.25V, dropout voltage is the input-to-output voltage differential with the minimum input
voltage being 2.25V. Minimum input operating voltage is 2.25V.
Note 7: IGND is the quiescent current. IIN = IGND + IOUT
Note 8: For adjustable device and fixed device with VOUT > 2.5V
Note 9: VREF ≤ VOUT ≤ (VIN – 1V), 2.25V ≤ VIN ≤ 16V, 10mA ≤ IL ≤1A
8
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Application Information
The GM66100/1/2 is a low dropout voltage regulator suitable for applications which ultra low dropout
performance is needed. Unlike older NPN-pass transistor designs, where the minimum dropout voltage is
limited by the base-to-emitter voltage drop and collector-to-emitter saturation voltage, dropout
performance of the PNP output of these devices is limited only by the low VCE saturation voltage.
The GM66100/1/2 regulator is fully protected from damage due to fault conditions. Linear current limiting
is provided. Output current during overload conditions is constant. Thermal shutdown disables the device
when the die temperature exceeds the maximum safe operating temperature. Transient protection allows
device (and load) survival even when the input voltage spikes above and below nominal. The output
structure of these regulators allows voltages in excess of the desired output voltage to be applied without
reverse current flow.
GM66100-x.x
VIN
IN
VOUT
OUT
CIN
GND
COUT
Figure 1. Capacitor Requirements
Output Capacitor
An output capacitor is required for the GM66100/1/2 to maintain stability and improve transient response.
Proper capacitor selection is important to ensure proper operation. The output capacitor selection is
dependent upon the ESR (equivalent series resistance) of the output capacitor to maintain stability.
When the output capacitor is 10μF or greater, the ESR value of the output capacitor should be less than
2Ω for the purpose of transient response improvement as well as stability. Ultra-low-ESR capacitors
(<100mΩ), such as ceramic chip capacitors, may promote instability. A low-ESR solid tantalum
capacitor works extremely well and provides good transient response and stability over temperature.
Aluminum electrolytes can also be used, as long as the ESR of the capacitor is <2Ω.
The value of the output capacitor can be increased without limit. Higher capacitance values help to
improve transient response and ripple rejection and reduce output noise.
Input Capacitor
An input capacitor of 1μF or greater is recommended when the device is more than 4 inches away from
the bulk ac supply capacitance or when the supply is a battery. Small, surface mount, ceramic chip
capacitors can be used for bypassing. Larger values will help to improve ripple rejection by bypassing
the input to the regulator, further improving the integrity of the output voltage.
Error Flag
The GM66101 features an error flag (FLG), which monitors the output voltage and sends out an error
signal when the output voltage drops 5% below its expected value. The error flag is an open-collector
output that pulls low under fault conditions and may sink up to 10mA. Low output voltage signifies a
number of possible problems, including an over current fault (the device is in current limit) or low input
voltage. The flag output is inoperative during over temperature conditions. A pull-up resistor from FLG to
either V!N or VOUT is required for proper operation. For information regarding the minimum and maximum
values of pull-up resistance, refer to the graph in the typical characteristics section of the data sheet.
9
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Enable Input
The GM66101 and GM66102 feature an active-high enable input (EN) which allows on-off control of the
regulator. The EN input has TTL/CMOS compatible thresholds for simple logic interfacing. EN may be
directly tied to VIN and pulled up to the maximum supply voltage.
Transient Response and 3.3V to 2.5V or 2.5V to 1.8V Conversion
The GM66100 series has excellent transient response to variations input voltage and load current. The
device has been designed to respond quickly to load current variations and input voltage variations.
Large output capacitors are not required to obtain this performance. A standard 10μF output capacitor,
preferably tantalum, is all that is required. Larger values help to improve performance even further.
By virtue of its low-dropout voltage, this device does not saturate into dropout as readily as similar NPN-
based designs. When converting from 3.3V to 2.5V or 2.5V to 1.8V, the NPN based regulators are
already operating in dropout, with typical dropout requirements of 1.2V or greater. To convert down to
2.5V or 1.8V without operating in dropout, NPN based regulators require an input voltage of 3.7V at the
very least.
The GM66100 regulator will provide excellent performance with an input as low as 3.0V or 2.5V
respectively. This gives the PNP based regulators a distinct advantage over older, NPN based linear
regulators.
Minimum Load Current
The GM66100/1/2 regulator is specified between finite loads. If the output current is too small, leakage
currents dominate and the output voltage rises. A 10mA minimum load current is necessary for proper
regulation.
Adjustable Regulator Design
GM66102
Enable
VOUT
Enable
VOUT
Adj
Shutdown
R1
R2
VIN
Gnd
VIN
COUT
Figure 2. Adjustable Regulator with Resistors
OUT = 1.24V x (1+ R1/R2)
V
The GM66102 allows programming the output voltage anywhere between 1.24V and the 16V maximum
operating rating of the family. Two resistors are used. The resistor values are calculated by:
R1 = R2 x (VOUT/1.24 - 1)
Where VOUT is the desired output voltage. Figure 2 shows component definition. Applications with widely
varying load currents may scale the resistors to draw the minimum load current required for proper
operation (see above).
10
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Package Outline Dimensions – SOT223
0.248 - 0.264
(6.30 - 6.71)
0.010 - 0.014
(0.25 - 0.36)
0.116 - 0.124
(2.95 - 3.15)
°
°
10 - 16
0.071
(1.8)
MAX
0.0008 - 0.0040
(0.0203 - 0.1016)
10°- 16 °
0.025 - 0.033
(0.64 - 0.84)
0.012
(0.31)
0.81
MIN
(4.6)
NOM
0.033 - 0.041
(0.84 - 1.04)
0.090
(2.29)
°
10
NOM
MAX
NOM
Package Outline Dimensions – TO252
0.039 – 0.050
(1.020 – 1.270)
0.205 – 0.215
(5.210 – 5.460)
0.018 – 0.023
(0.460 – 0.580)
0.055 – 0.080
(1.400 – 2.030)
SEATING PLAN
0.370 – 0.410
(9.400 – 10.420)
0.210 – 0.228
(5.330 – 5.800)
0.020
(0.510)
MIN
0.045 – 0.060
(1.150 – 1.520)
0.090
(2.285)
TYP
0.018 – 0.023
(0.460 – 0.580)
0.030 – 0.045
(0.760 – 1.140)
0.180
(4.570)
TYP
11
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Package Outline Dimensions – TO263
0.390 - 0.415
(9.906 - 10.541)
0.105 - 0.180
(4.191 - 4.572)
0.045 - 0.055
(1.143 - 1.397)
0.060
(1.524)
TYP
15
TYP
0.330 - 0.370
(8.382 - 9.398)
0.059
(1.499)
TYP
0.143 + 0.012
0.143 - 0.002
(3.632 + 0305)
(3.362 - 0.508)
0.050 +/- 0.012
(1.270 +/- 0.305)
0.020 - 0.039
(0.510 - 0.990)
0.013 - 0.023
(0.330 - 0.584)
0.090 - 0.110
(2.286 - 2.794)
0.050
(1.270)
Package Outline Dimensions – SO 8
0.189 - 0.197
(4.800 - 5.004)
0.228 - 0.244
(5.791 - 6.198)
0.016 - 0.050
(0.406 - 0.270)
D
0.050
(1.270)
TYP
0.014 - 0.020
(0.356 - 0.508)
0.150 - 0.157
(3.810 - 3.988)
0.053 - 0.059
(1.346 - 1.753)
8.0
MAX
SEATING PLAN
0.008 - 0.010
(0.203 - 0.254)
0.004 - 0.010
(0.012 - 0.254)
12
GM6610x Series
1.0A ULTRA LOW DROPOUT VOLTAGE
REGULATORS
Ordering Number
G
M 66100 -1.8 TA3
R
G
APM Circuit
Output
Package Type
Shipping Type
Gamma Type
Micro
Voltage
1.8 = 1.8V TA3: TO263
2.5 = 2.5V TB3: TO220
3.3 = 3.3V TC3: TO252
5.0 = 5.0V ST3: SOT223
R:Taping& Reel
T: Tube
Blank:
Pb-free
G:Green
G
M 66101 -1.8 S8
R
G
APM Circuit
Output
Package Type
Shipping Type
Gamma Type
Micro
Voltage
1.8 = 1.8V S8: SOP-8
2.5 = 2.5V
R:Taping& Reel
T:Tube
Blank:
Pb-free
G:Green
3.3 = 3.3V
5.0 = 5.0V
G
M 66102
S8
R
G
APM Circuit
Output
Package Type
Shipping Type
Gamma Type
Micro
Voltage
Adj
S8: SOP-8
R:Taping& Reel
T:Tube
Blank:
Pb-free
G:Green
Note:
Pb-free products:
♦
♦
RoHS compliant and compatible with the current require-ments of IPC/JEDEC J-STD-020.
Suitable for use in Pb-free soldering processes with 100% matte tin (Sn) plating.
Green products:
♦
♦
Lead-free (RoHS compliant)
Halogen free(Br or Cl does not exceed 900ppm by weight in homogeneous material and total of
Br and Cl does not exceed 1500ppm by weight)
8
1
10
6
相关型号:
©2020 ICPDF网 联系我们和版权申明