15DMOW4 [GAPTEC]
15W - Single Output - Wide Input - Isolated & Regulated;型号: | 15DMOW4 |
厂家: | GAPTEC |
描述: | 15W - Single Output - Wide Input - Isolated & Regulated |
文件: | 总6页 (文件大小:1858K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
15DMOW4_S 1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
DC-DC Converter
15 Watt
Wide 4:1 input voltage range
High efficiency up to 88%
Short circuit protection (SCP)
Isolation voltage: 1.5kVDC
Over-current, over-voltage
protection
Operating temperature range:
The 15DMOW4_S1.5 series are isolated 15W DC/DC converters with 4:1
input voltage. They feature efficiency up to 88%, 1500VDC isolation,
operating temperature of -40°C to +85°C, input under-voltage protec-
tion, output over-voltage, output over-current, output short circuit pro-
tection and meets IEC60950-1.
-40°C to +85°C
Fixed switching frequency
Remote on/off logic
International standard pin-out
Monotonic startup into
normal and pre-bias loads
Adjustable output voltage
range
Under-voltage lockout
RoHS compliant
They are widely applied in distributed power architectures, wireless
networks, access and optical network equipment, enterprise networks,
latest generation IC’s (DSP, FPGA, ASIC) and microprocessor powered
applications.
Meets IEC60950-1
Common specifications
Short circuit protection:
Cooling:
Output specifications
Hiccup, continuous, self-recovery
Free air convection
-40°C~+85°C
Item
Test condition
Min
Typ
Max
Units
Voltage set point
25°C, Io=Io (max)
• 3.3V
• 12V
3.25 3.3
11.82 12
3.35
12.18
V
V
Operation temperature range:
Storage temperature range:
Storage humidity range:
Thermal stability time:
FIT:
Voltage regulation Vin= Vin (min) to
Vin(max)
0.05
0.2
%Vo
-40°C~+125°C
90% MAX
Load regulation
Io=0 to Io (max)
• 3.3V
• 12V
0.1
0.05
0.3
0.2
%Vo
%Vo
30mins
167 109/hours
DC Current-Limit
Inception
3V
110
180
%Io
Vibration:
IEC60068-2-6: 10~500Hz sweep, 0.75mm
excursion, 10g acceleration, 10minutes
in each 3 perpendicular directions
Current Limit
12V
1.43
2.34
3.0
A
Voltage precision
(full temperature
range)
Vin=Vin (min) to
Vin(max), Io=0 to
Io(max)
%Vo
Shock:
IEC 60068-2-27:200g acceleration, dura-
tion 3 ms,6 drops in each 3 perpendicu-
lar directions
Voltage adjust-
ment range
Rated power
Io=0 to Io (max)
• 3.3V
Safety:
Compliant to IEC60950-1, UL60950-
1,EN60950-1 and GB4943
3.3
-10
0.008
3.63
10
V
Switching frequency:
300KHz MIN,
3.3V: 350KHz MAX, 12V: 500KHz MAX
• 12V
%Vo
Temperature drift Full temp. range
0.008
100
0.02 %/°C
Transportation:
ETS300019-1-2
6,000,000 hours
9g
Dynamic response 25%-50%-25%,50%-75%-
recovery time
200
µS
50% Io(nom)
MTBF (Telcordia SR332, 40°C):
Weight:
Dynamic response di/dt=0.1A/µS, 10µF
overshoot
Tantalum capacitor,
1µF ceramic capacitor
• 3.3V
3
8
3
%Vo
%Vo
Protection specifications
• 12V
Item
Test condition
Min
Typ
Max
Units
Ripple and noise* P-P
Input under voltage
lockout
Io=0 to Io(max)
full temp. range
• Turn-on
• 3.3V
• 12V
40
50
80
100
mV
mVp-p
16
17
16
1
18
17
1.5
VDC
VDC
VDC
• Turn-off
• Hysteresis
15
RMS
• 3.3V
• 12V
0.5
10
15
20
50
mV
mVRMS
Over current
protection
Hiccup mode, auto-
matic recovery
yes
A
Turn-on delay
time
Time from instant at
which Vin=Vin (Turn-on)
until Vo=10% of Vo
(nom)
• 3.3V
• 12V
Over voltage
protection
Clamp voltage mode
• 3.3V
• 12V
3.79
13.44
5
18
VDC
VDC
10
25
ms
ms
10
Over temperature
protection
Automatic recovery
See OTP section
125
10
°C
Turn-on rise time
Time for Vo to rise
from 10% of Vo (nom)
to 90% of Vo (nom)
• 3.3V
Over Temperature
Protection Hysteresis
°C
10
50
ms
ms
• 12V
30
Example:
Turn-on transient: Vin=Vin(min) to Vin
15DMOW4_2415S1.5
output voltage
overshoot
(max), Io=0 to Io (max),
full temp. range
• 3.3V
15 = 15Watt; D = DIP; M = Miniature; O = Open frame; W4 = wide
input (4:1); 18-36Vin; 15Vout; S = single output; 1.5 = 1500VDC
5
3
%Vo
%Vo
• 12V
* Measured with 10uF Tantalum capacitor and 1uF ceramic capacitor across output.
Page 1 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
15DMOW4_S1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Input specifications
Isolation specifications
Item
Item
Test condition
Min
18
Typ
48
Max
75
Units
VDC
Test condition
Input/output
Test at 500VDC
Min
10
Typ
Max
Units
VDC
MΩ
Operating input
voltage
Io=0 to Io(max)
Isolation voltage*
Isolation resistance
Isolation capacitance**
1500
Max. input current
Input current
100% load Vin= Vin
(min) to Vin (max)
• 3.3V
1000
pF
1.3
1.1
A
A
*
Test duration 1 minute, leak current lower than 10mA, no arcing or breakdown
** The isolation resistance of input to output is more than 10MΩ
• 12V
no load, full input
• 3.3V
• 12V
30
15
60
50
mA
mA
Stand-by input
current
REM disabled
3
6
mA
Remote control specifications
Item
Test condition
Min
-0.7
2
Typ
Max
0.8
18
Units
VDC
VDC
Reflected ripple
current
peak-to-peak, 5Hz
to 20 MHz,12µH
source inductance
8
30
mA
Logic low voltage
Logic high voltage
Inrush transient
Starting voltage*
Vin=Vin (min) to
Vin (max), Io=0 to
Io (max)
*
Converter guaranteed logic high when REM pin is left open
• 3.3V
0.1
A2S
A2S
• 12V
0.01
• 24VDC input
• 48VDC input
9
18
VDC
VDC
Input voltage ripple 120Hz
rejection
60
dB
Input fuse
3
A
* Nominal input voltage & constant resistance load
Product Selection Guide
Part Number
Input Voltage [VDC]
Output Voltage [VDC]
Output Current [mA]
Efficiency [%, Typ.]
Capacitive load [µF, Max.]
Nominal
Range
Max
Full load
15DMOW4_4803S1.5
15DMOW4_4812S1.5
48
48
18-75
18-75
80
80
3.3
12
5000
1300
88
1000
470
88.5
Typical characteristics
Converter Efficiency Vs. Output Current
Available load current vs. ambient temperature
and airflow for the module mounted horizontally
Page 2 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
15DMOW4_S1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Input Reflected Ripple Current Test Setup
Output Ripple and Noise Test Setup
Measure input reflected ripple current with a simulated
source inductance of 12µH. The measurement points for
input reflected ripple current is showed above.
Scope measurements should be made using a BNC
socket, with a 1µF ceramic capacitor and a 10 µF tantalum
capacitor. Position the oscilloscope probe between 51mm
and 76mm (2 inch and 3 inch) from the module.
Remote on/off
The REM pin is used to turn the power converter remote on
or off via a system signal. This power module is negative logic
version. When the REM pin is at logic high the power turns off
and turns on at logic low.
To turn the power module on and off, the user must supply a
switch to control the voltage between the REM pin and -Vin
terminal (see Figure 3). A logic low is VREM = -0.7V to 0.8V.
The maximum IREM during logic low is 1mA. The switch
should maintain a logic low voltage while sinking 1mA. During
logic high, the typical maximum VREM voltage is18V.
If not using the remote on/off feature, short REM pin to -Vin.
Tref measurement location
3.3V
12V
Page 3 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
15DMOW4_S1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Application of trim and calculation of trim resistance
3.3V
12V
Output voltage trim allows the user to increase or decrease
the output voltage set point of a module. This is
accomplished by connecting an external resistor between the
TRIM pin and either the Vout+ or Vout- pins. If not using the
trim feature, leave the TRIM pin open.
Recommended reflow profile
Peak product temperature 12V: +260°C
Page 4 of 6
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
15DMOW4_S1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Recommended EMC application
Suggested configuration to meet the conducted emission
limits of EN55022 Class A.
Mechanical dimensions
3.3V
12V
Page 5 of 6
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
15DMOW4_S1.5 series
15W - Single Output - Wide Input - Isolated & Regulated
1“ x 1“ DC-DC Converter
Recommended pad layout
3.3V
12V
Note:
1. The maximum capacitive loads offered were tested at input voltage range and
full load.
2. Only typical model listed. Non-standard models will be different from the abo-
ve, please contact us for more details.
3. All specifications are measured at TA = 25°C, humidity <75%, nominal input
voltage and rated output load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate
standards.
5. We can provide product customization service, please contact our technicians
directly for specific information.
6. Our products shall be classified according to ISO14001 and related environmen-
tal laws and regulations, and shall be handled by qualified units.
Page 6 of 6
15DMOW4_S1.5 – Rev. 2020-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明