LMO78-1.0 [GAPTEC]
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output;型号: | LMO78-1.0 |
厂家: | GAPTEC |
描述: | Wide Input Non-Isolated & Regulated, Single Positive/Negative Output |
文件: | 总4页 (文件大小:1181K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LMO78_1.0 Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Switching Regulator
High efficiency up to 96%
Operating temperature
range: -40°C ~ +85°C
Open frame SIP package
No-load input current as low
as 0.1mA
Meets UL60950, EN60950
standards
The LMO78_1.0 series is a high efficiency switching regulator and ideal
substitute for the LM78xx series three-terminal linear regulators. The
product is featured with high efficiency, low loss, short circuit
protection and no heat sink is required. They are widely used in indust-
rial control, instrumentation, and electric power applications.
Short circuit protection (SCP)
UL-60950-1 (E347551)
Common specifications
Short circuit protection:
No-load input current:
Reverse Polarity Input:
Input Filter:
Output specifications
Continuous, automatic recovery
0.1mA TYP, 1mA MAX
Forbidden
Item
Test conditions
Min
Typ
Max
Units
Output voltage
accuracy
100% load
• LMO78_03-0.5
• Others
2
2
4
3
%
%
Capacitor Filter
Line regulation
Load regulation
Ripple + Noise*
Input Voltage Range
10% to 100% load
0.2
0.4
20
0.4
0.6
75
%
%
Cooling:
Free air convection
Operation temperature range:
-40°C~+85°C
Power derating above 71°C
20MHz Bandwidth
Vin=24VDC
0% -100% load
mVp-
p
Storage temperature range:
Pin welding resistance temperature:
Storage humidity range:
Package material:
-55°C ~+125°C
Switching frequency Full load, nom. input
260°C MAX, 1.5mm from case for 10 sec
< 95%RH
• LMO78_03-1.0/
LMO78_05-1.0
• Others
420
580
520
620
KHz
680
50
780
300
KHz
mV
Plastic [UL94-V0]
Transient response
deviation
Nominal input, 25%
load step change
MTBF:
>2,000,000 hours
+25°C MIL-HDBK-217F
Transient recovery
time
Nominal input, 25%
load step change
0.1
1
ms
Weight:
2.1g
Temperature
coefficient
-40 °C to +85 °C
ambient
0.03
%/°C
Note:
1. The max. capacitive load should be tested within the input voltage range and
under full load conditions;
* Test ripple and noise by “parallel cable” method. With the load lower than 20%,
the maximum ripple and noise of 3.3V/5V output products will be 100mVp-p,
12V/15V output products will be 2%Vo.
2. Without any special statement, all indexes are only specific to positive output
application;
3. Unless otherwise specified, data in this datasheet should be tested under the
conditions of Ta = 25°C, humidity <75% when inputting nominal voltage and
outputting rated load;
Example:
4. All index testing methods in this datasheet are based on our Company’s
corporate standards;
LMO78_05-1.0
LM = Series; S = SIP Case; 05 = 5Vout; 1.0 = 1.0A
5. The performance indexes of the product models listed in this manual are as
above, but some indexes of non-standard model products will exceed the
above-mentioned requirements, and please directly contact with our technician
for specific information;
6. Specifications subject to change without prior notice.
EMC specifications
EMI
CE
CISPR22/EN55022
CISPR22/EN55022
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
IEC/EN61000-4-5
IEC/EN61000-4-6
CLASS B
CLASS B
Contact 4KV
10V/m
(External circuit refer to EMC recommended circuit, 2 or EMC module application circuit)
(External circuit refer to EMC recommended circuit, 2 or EMC module application circuit)
perf. Criteria B
EMI
RE
EMS
EMS
EMS
EMS
EMS
ESD
RS
perf. Criteria A
EFT
Surge
CS
1KV
perf. Criteria B (External circuit refer to EMC recommended circuit, 1 )
line to line 1KV perf. Criteria B (External circuit refer to EMC recommended circuit, 1 )
3 Vr.m.s perf. Criteria A
Page 1 of 4
LMO78_1.0 – Rev. 2020-1.4
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LMO78_1.0 Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Part Number
Input Voltage [VDC]
Nominal (Range)
Output Voltage
[VDC]
Output Current
[mA]
Efficiency @full load
[% typ, min/typ Vin]
Max. capacitive load
[µF]
LMO78_03-1.0
LMO78_05-1.0
24 (6-36)
3.3
1000
90/81
680
24 (8-36)
12 (8-27)
5
-5
1000
-500
93/86
86/82
680
330
LMO78_12-1.0
LMO78_15-1.0
24 (16-36)
12 (8-20)
12
1000
-300
96/93
89/88
680
330
-12
24 (20-36)
12 (8-18)
15
-15
1000
-300
96/94
89/89
680
330
Typical characteristics
Efficiency
LMO78_15-1.0
LMO78_05-1.0
LMO78_15-1.0
LMO78_05-1.0
LMO78_15-1.0
LMO78_05-1.0
LMO78_15-1.0
LMO78_05-1.0
Page 2 of 4
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LMO78_1.0 – Rev. 2020-1.4
Specifications subject to change without notice.
LMO78_1.0 Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Typical application circuit
LMO78
LMO78
LMO78
LMO78
Positive and Negative output parallelling application circuit
Note:
Part number
C1,C3
(Ceramic Capacitor)
C2,C4
(Ceramic Capacitor)
1. C1 and C2 (C3 and C4) are required and should be connected close to the
pin terminal of the module.
2. The capacitance of C1 and C2 (C3 and C4) refer to table on the left.
3. To reduce the output ripple furtherly. C2 and C4 can be increased properly
if required, and tantalum or low ESR electrolytic capacitors may also
suffice.
4. When the products are used as shown in the „positive and negative output
paralleling application circuit“, an inductor named as LDM up to 10μH is
recommended in the circuit to reduce the mutual interference.
5. Cannot be used in parallel for output and hot swap.
LMO78_03-1.0
LMO78_05-1.0
LMO78_12-1.0
LMO78_15-1.0
10μF/50V
10μF/50V
10μF/50V
10μF/50V
22μF/10V
22μF/10V
22μF/25V
22μF/25V
EMC solution-recommended circuit
Part 1 in the Fig. 5 is for EMS test, part 2 is for EMI filtering; parts
can be added based on actual requirement.
and
FUSE
MOV
LDM1
82μH
C0
C1/C2
C5
LDM2
12μH
Selected based on the
actual input current
from the customer
S20K30
680μF /50V
Refer to table at
typical application
circuit
4.7μF /50V
Page 3 of 4
LMO78_1.0 – Rev. 2020-1.4
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LMO78_1.0 Series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Mechanical dimensions and footprint
Page 4 of 4
LMO78_1.0 – Rev. 2020-1.4
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明