LOT10 [GAPTEC]
10A - Non-Isolated & Regulated, Single output POL power converter;型号: | LOT10 |
厂家: | GAPTEC |
描述: | 10A - Non-Isolated & Regulated, Single output POL power converter |
文件: | 总5页 (文件大小:2835K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LOT10_10R-X Series
10A - Non-Isolated & Regulated, Single output POL power converter
Switching Regulator
Efficiency up to 94%
Input under-voltage, over-
current protection
High-speed transient response
EN62368 approved
The LOT10_10R-X is a 10A non-isolated switching regulator. The output
voltage is accurately adjustable from 0.75V to 5.0V, and the product is
featured with high efficiency, fast transient response, input under-volta-
ge, output short circuit and over-current protection. It meets CLASS B of
CISPR32/EN55032 EMI standards by adding the recommended external
components.
Operating temperature range:
-40°C ~ +85°C
Short circuit protection (SCP)
Compact SMD package
They are widely used in applications such as communications, computer
network industry, power distributed architecture, workstations, servers,
LANs/WANs and provide high current with fast transient response for
high-speed chips such as FPGA, DSP, and ASIC.
Common specifications
Short circuit protection:
Cooling:
Output specifications
Continuous, automatic recovery
Nature or forced convection
-40°C~+85°C
Item
Test conditions
Min
Typ
1
Max
2
Units
%
Voltage accuracy
Full load, nominal
input voltage
Operation temperature range:
Storage temperature range:
Reflow soldering temperature:
Line regulation
Load regulation
Full load, input
voltage range
0.3
0.4
65
%
%
-55°C ~+125°C
Peak temp. Tc ≤245°C, maximum
duration time≤60s over 217°C. For
actual application, please refer to
IPC/JEDEC J-STD-020D.1.
nominal input,
0% - 100% load
Ripple + Noise*
Trim
20MHz Bandwidth
100
5
mVp-p
VDC
Storage humidity range:
MTBF (+25°C MIL-HDBK-217F):
Dimensions:
< 95%RH
0.75
1000 K hours MIN
33.00 x 13.50 x 8.30mm
8.6g
Sense
110
%Vo
Temperature
coefficient
0.02
75
20
%/°C
Weight:
Transient response
deviation**
mV
µs
Transient
recovery time**
Input specifications
Item
Test conditions
Min
6
Typ
Max
8.3
Units
mA
External load
capacitance
• 1 mΩ ≤ESR <10 mΩ
• ESR≥10mΩ
5000
6000
uF
uF
Input current
nominal input voltage
full load/no load
4340/70
Over current
protection
Nominal input
320
%Io
Start-up voltage
VDC
VDC
Switching frequency
300
KHz
Under voltage
protection
Unless otherwise specified, parameters in this table were measured under the
5VDC output voltage.
Reverse polarity
input
Avoid/not protected
*
The “parallel cable” method is used for Ripple and Noise test.
Input filter
Hot plug
Ctrl*
Capacitance filter
Unavailable
** Nominal input, 50%-100%-50% load step change, di/dt=2.5A/us, with external 2
x 150 µF polymer capacitors.
Module on
• LOT10_10R-P
Ctrl pin open or pulled high
(Vin-2.5VDC~Vin)
EMC specifications
The Ctrl pin voltage
is referenced to
GND.
EMI
EMI
EMS
CE
CISPR32/EN55032
CLASS B
• LOT10_10R-N
Ctrl pin pulled low to GND
(0~0.5VDC)
see EMC compliance circuit
Module off
• LOT10_10R-P
RE
CISPR32/EN55032
see EMC compliance circuit
CLASS B
Ctrl pin pulled low to GND
(0~0.5VDC)
Ctrl pin open or pulled high
(Vin-2.5VDC~Vin)
ESD
IEC/EN61000-4-2 Contact 6KV
perf. Criteria A
• LOT10_10R-N
Input current when
off
2
mA
Note:
1. The max. capacitive load was tested at input voltage range and full load.
2. Unless otherwise specified, parameters were measured under the conditions
of Ta=25°C, humidity<75%RH with nominal input voltage, 5VDC output voltage
and rated output load.
Unless otherwise specified, parameters in this table were measured under the
5VDC output voltage.
3. All index testing methods in this datasheet are based on our Company’s
corporate standards.
4. Specifications subject to change without prior notice.
Example:
LOT10_10R-P
LO= Series; T10= SMT10; 10= Output current: 10A; R= Revised;
P= positive logic control
Page 1 of 5
LOT10_10R-X – Rev. 2019-1.0
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LOT10_10R-X Series
10A - Non-Isolated & Regulated, Single output POL power converter
Part Number
Input Voltage [VDC]
Output Voltage Range2
[VDC]
Output Current
[A; min/max]
Efficiency
[%, min/typ]
nominal (range)
Max.1
LOT_12-10R-X
12 (8.3~14)
15
0.75 ~ 5.0
0/10
93/96
X: Suffix “P” indicates that the Ctrl pin is positive logic control, “N” indicates that the Ctrl pin is negative logic control.
Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage.
1. Exceeding the maximum input voltage may cause permanent damage.
2. The default output voltage is 0.75VDC, which can be adjusted to 1.2VDC, 1.8VDC, 2.5VDC, 3.3VDC, 5VDC. See Trim instructions for specific output
voltage adjustment.
Typical characteristics
Typical application
LOT10-10R-X
Note:
1. 100 µF or 220 µF capacitor (C1) and 22 µF or 47 µF capacitor (C2) are required
and should be connected close to the pin terminal, to ensure the stability of the
converter;
2. To reduce the output ripple furtherly,increased values and/or tantalum or low
ESR electrolytic capacitors may also be used instead;
3. Refer to Table 1 for C1 and C2 capacitor values;
4. Converter cannot be used for hot swap and with output in parallel.
EMC compliance circuit
Refer to the Cout in
typical application
Page 2 of 5
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LOT10_10R-X – Rev. 2019-1.0
Specifications subject to change without notice.
LOT10_10R-X Series
10A - Non-Isolated & Regulated, Single output POL power converter
Trim function
Trim function for output voltage adjustment (open if unused)
Notes: 1. RT : Resistance of Trim; Vo: The trim up voltage;
2. If RT = ∞ or Trim pin open, Vo = 0.7525 VDC.
Remote sense application
Remote sense connection if not used
Note:
1. If the sense function is not used for remote regulation the user
must connect the Sense to + Vo at the DC-DC converter pins
and will compensate for voltage drop across pins only;
2. The connections between Sense and +Vo must be kept as short
as possible, otherwise they may be picking up noise, interfe-
rence and/or causing unstable operation of the power module.
Remote sense connection used for compensation
Note:
1. PCB-tracks or cables/wires for Remote Sense must be kept as
short as possible;
2. Using remote sense with long wires long wires may cause
unstable operation. Note that large wire impedance may
cause oscillation of the output voltage and/or increased ripple.
Consult technical support or factory for further advice of sense
operation;
3. We recommend using adequate cross section for PCB-track
layout and/or cables to connect the power supply module to
the load in order to keep the voltage drop below 0.3V and to
make sure the power supply‘s output voltage remains within
the specified range.
Page 3 of 5
LOT10_10R-X – Rev. 2019-1.0
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LOT10_10R-X Series
10A - Non-Isolated & Regulated, Single output POL power converter
Efficiency
Page 4 of 5
LOT10_10R-X – Rev. 2019-1.0
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
LOT10_10R-X Series
10A - Non-Isolated & Regulated, Single output POL power converter
Mechanical dimensions
Page 5 of 5
LOT10_10R-X – Rev. 2019-1.0
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
相关型号:
©2020 ICPDF网 联系我们和版权申明