GL811E(64LQFP) [GENESYS]
Bus Controller, CMOS, PQFP64;型号: | GL811E(64LQFP) |
厂家: | GENESYS LOGIC |
描述: | Bus Controller, CMOS, PQFP64 |
文件: | 总35页 (文件大小:1277K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Genesys Logic, Inc.
GL811E
USB 2.0 to ATA / ATAPI
Bridge Controller
Datasheet
Revision 1.23
Feb. 02, 2005
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Copyright:
Copyright © 2005 Genesys Logic Incorporated. All rights reserved. No part of the materials may be
reproduced in any form or by any means without prior written consent of Genesys Logic Inc..
Disclaimer:
ALL MATERIALS ARE PROVIDED "AS IS" WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY
KIND. NO LICENSE OR RIGHT IS GRANTED UNDER ANY PATENT OR TRADEMARK OF
GENESYS LOGIC INC.. GENESYS LOGIC HEREBY DISCLAIMS ALL WARRANTIES AND
CONDITIONS IN REGARD TO MATERIALS, INCLUDING ALL WARRANTIES, IMPLIED OR
EXPRESS, OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF INTELLECTUAL PROPERTY. IN NO EVENT SHALL GENESYS LOGIC
BE LIABLE FOR ANY DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES RESULTING
FROM LOSS OF INFORMATION OR PROFITS. PLEASE BE ADVISED THAT THE MATERIALS
MAY CONTAIN ERRORS OR OMMISIONS. GENESYS LOGIC MAY MAKE CHANGES TO THE
MATERIALS OR TO THE PRODUCTS DESCRIBED THEREIN AT ANY TIME WITHOUT NOTICE.
Trademarks:
is a registrated trademark of Genesys Logic Inc..
All trademarks are the properties of their respective owners.
Office:
Genesys Logic, Inc.
12F, No. 205, Sec. 3, Beishin Rd., Shindian City,
Taipei, Taiwan
Tel: (886-2) 8913-1888
Fax: (886-2) 6629-6168
http://www.genesyslogic.com
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 2
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Revision History
Revision
1.00
Date
06/13/2003 First formal release.
Description
Changed product name from GL811 to GL811E.
1.01
06/24/2003
1. Added some features in Chapter 2.
2. Added 64 pin LQFP data in pinouts, pin description and package dimension.
3. Added Chapter 8 “Ordering Infromation”.
1.10
11/26/2003
Changed pin# 38,39,21 name from IOADR0~2 to DA0~2.
1.11
1.20
11/27/2003
05/05/2004
1. Removed PIO mode description.
2. Changed package dimension
1. Added USB2.0 certified Test ID in Chapter 2 Features
2. Updated IC Marking in package dimension diagram
Added TQFP package information in Features, Package Dimension and
Ordering Information.
1.21
09/23/2004
1.22
1.23
12/29/2004
02/02/2005
Changed IC marking in package dimension
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 3
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
TABLE OF CONTENTS
CHAPTER 1 GENERAL DESCRIPTION........................................................................... 7
CHAPTER 2 FEATURES ....................................................................................................... 8
CHAPTER 3 PIN ASSIGNMENT......................................................................................... 9
3.1 PINOUTS............................................................................................................................... 9
3.2 PIN DESCRIPTIONS............................................................................................................11
CHAPTER 4 BLOCK DIAGRAM ......................................................................................13
CHAPTER 5 FUNCTION DESCRIPTION .......................................................................14
CHAPTER 6 ELECTRICAL CHARACTERISTICS ......................................................15
6.1 ABSOLUTE MAXIMUM RATINGS......................................................................................15
6.2 TEMPERATURE CONDITIONS ...........................................................................................15
6.3 DC CHARACTERISTICS ....................................................................................................15
6.3.1 I/O 8 Type digital pins (For pad type I/O 8 @ VCC=3.6V) ...............................15
6.3.2 I/O 16 Type digital pins (For pad type I/O 16 @ VCC=3.6V)...........................16
6.3.3 D+/ D- (For pad type u20mia @ VCC=3.6V) .......................................................16
6.3.4 Switching Characteristics......................................................................................16
6.4 AC CHARACTERISTICS- ATA/ ATAPI...........................................................................17
6.4.1 Register Transfers ..................................................................................................18
6.4.2 Multiword DMA data transfer .............................................................................19
6.4.3 Ultra DMA data transfer.......................................................................................23
6.5 AC CHARACTERISTICS - USB 2.0 ...................................................................................30
CHAPTER 7 PACKAGE DIMENSION.............................................................................31
CHAPTER 8 ORDERING INFORMATION ....................................................................35
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 4
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
LIST OF FIGURES
FIGURE 3.1 - 48 PIN LQFP/TQFP PINOUT DIAGRAM.......................................................... 9
FIGURE 3.2 - 64 PIN LQFP/TQFP PINOUT DIAGRAM........................................................10
FIGURE 4.1 - BLOCK DIAGRAM .............................................................................................13
FIGURE 6.1 - INITIATING A MULTIWORD DMA DATA BURST ...........................................20
FIGURE 6.2 - SUSTAINING A MULTIWORD DMA DATA BURST..........................................21
FIGURE 6.3 - DEVICE TERMINATING A MULTIWORD DMA DATA BURST........................21
FIGURE 6.4 - HOST TERMINATING A MULTIWORD DMA DATA BURST............................22
FIGURE 6.5 - INITIATING AN ULTRA DMA DATA-IN BURST ..............................................24
FIGURE 6.6 - SUSTAINED ULTRA DMA DATA-IN BURST ....................................................24
FIGURE 6.7 - HOST PAUSING AN ULTRA DMA DATA-IN BURST........................................25
FIGURE 6.8 - DEVICE TERMINATING AN ULTRA DMA DATA-IN BURST ..........................25
FIGURE 6.9 - HOST TERMINATING AN ULTRA DMA DATA-IN BURST ..............................26
FIGURE 6.10 - INITIATING AN ULTRA DMA DATA-OUT BURST ........................................27
FIGURE 6.11 - SUSTAINED ULTRA DMA DATA-OUT BURST..............................................27
FIGURE 6.12 - DEVICE PAUSING AN ULTRA DMA DATA-OUT BURST ..............................28
FIGURE 6.13 - HOST TERMINATING AN ULTRA DMA DATA-OUT BURST...........................29
FIGURE 6.14 - DEVICE TERMINATING AN ULTRA DMA DATA-OUT BURST.....................30
FIGURE 7.1 - GL811E 48 PIN LQFP PACKAGE...................................................................31
FIGURE 7.2 - GL811E 48 PIN TQFP PACKAGE...................................................................32
FIGURE 7.3 - GL811E 64 PIN LQFP PACKAGE...................................................................33
FIGURE 7.4 - GL811E 64 PIN TQFP PACKAGE...................................................................34
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 5
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
LIST OF TABLES
TABLE 3.1 - PIN DESCRIPTIONS.............................................................................................11
TABLE 6.1 - MAXIMUM RATINGS ..........................................................................................15
TABLE 6.2 - TEMPERATURE CONDITIONS ............................................................................15
TABLE 6.3 - I/O 8 TYPE DIGITAL PINS (FOR PAD TYPE I/O 8 @ VCC=3.6V) .....................15
TABLE 6.4 - I/O 16 TYPE DIGITAL PINS (FOR PAD TYPE I/O 16 @ VCC=3.6V) .................16
TABLE 6.5 - D+/ D- (FOR PAD TYPE U20MIA @ VCC=3.6V)................................................16
TABLE 6.6 - SWITCHING CHARACTERISTICS .......................................................................16
TABLE 6.7 - ULTRA DMA DATA BURST TIMING REQUIREMENTS.......................................23
TABLE 8.1 - ORDERING INFORMATION.................................................................................35
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 6
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 1 GENERAL DESCRIPTION
The GL811E is a highly-compatible, low cost USB 2.0 to ATA / ATAPI bridge controller, which integrates
Genesys Logic own design high speed UTMI (USB 2.0 Transceiver Macrocell Interface) transceiver.
As a one-chip solution which complies with Universal Serial Bus specification rev. 2.0 and ATA / ATAPI-6
specification rev 1.0, the GL811E can support various kinds of ATA / ATAPI device. There are totally 4
endpoints in the GL811E controller, Control (0), Bulk In (1), Bulk Out (2), and Interrupt (3). By complies with
the USB Storage Class specification ver.1.0 (Bulk only protocol), the GL811E can support not only plug and
play but also Windows XP/ 2000/ ME default driver.
The GL811E uses 12MHz crystal and slew-rate controlled pads to reduce the EMI issue. With 48-pin LQFP
(9mmX9mm) package, the GL811E is the best cost/ performance solution to fit different situations in the USB
2.0 high speed storage class applications such as Hard Disk, CD-ROM, CD-R / RW and DVD-ROM.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 7
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 2 FEATURES
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Complies with Universal Serial Bus specification rev. 2.0.
Complies with ATA/ATAPI-6 specification rev 1.0.
Complies with USB Storage Class specification ver.1.0. (Bulk only protocol)
Operating system supported: Win XP / 2000 / Me / 98 / 98SE; Mac OS 9.X / X.
Integrated USB 2.0 Transceiver Macrocell Interface (UTMI) transceiver and Serial Interface Engine (SIE).
USB 2.0 certified (TestID=40380268)
Supports 4 endpoints: Control (0) / Bulk Read (1) / Bulk Write (2) / Interrupt (3).
64 / 512 bytes Data Payload for full / high speed Bulk Endpoint.
Supports 16-bit Multiword DMA mode and Ultra DMA mode interface (Ultra 33 / 66).
Embedded 7.5 MIPS RISC CPU.
ROM size: 4k words; RAM size: 128 bytes.
Supports Power Down mode and USB suspend indicator.
Supports USB 2.0 TEST mode features.
Supports 2 GPIO (GPIO5 & 6) for programmable AP (only for 64 pin package).
Supports device power control for power on/off when running suspend mode (only for 64 pin package).
Supports 32 bit and 48 bit LBA hard disk.
Provides LED indicator for Full Speed and High Speed (only for 64 pin package).
12 MHz external clock to provide better EMI.
3.3V power input; 5V tolerance pad for IDE interface.
Supports Wakeup ability.
Available in 48-pin LQFP/TQFP and 64-pin LQFP/TQFP package.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 8
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 3 PIN ASSIGNMENT
3.1 Pinouts
DMARQ
IODD[0]
IODD[1]
IODD[2]
IODD[3]
DGND2
DVCC2
IODD[4]
IODD[5]
IODD[6]
IODD[7]
GPIO1
37
38
39
40
41
42
43
44
45
46
47
48
24
23
22
21
20
19
18
17
16
15
14
13
AVCC1
RREF
AGND0
DMH
DMF
DPH
DPF
GL811E
AVCC0
RPU
RESET#
DA2/SK
CS1_
LQFP/TQFP - 48
Figure 3.1 - 48 Pin LQFP/TQFP Pinout Diagram
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 9
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
49
32
NC
DMARQ
IODD0
IODD1
IODD2
IODD3
DGND1
DVCC1
IODD4
IODD5
IODD6
IODD7
GPIO1
X2
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
AVCC1
RREF
AGND0
DMH
DMF
DPH
DPF
AVCC0
RPU
GL811E
RESET#
DA2
CS1_
NC
PWR_CTL
F_LED
H_LED
NC
LQFP/TQFP - 64
NC
Figure 3.2 - 64 Pin LQFP/TQFP Pinout Diagram
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 10
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
3.2 Pin Descriptions
Table 3.1 - Pin Descriptions
48Pin# 64 Pin# I/O Type
Pin Name
GPIO7
Description
B
1
-
1
GPIO7 (**)
(tri)
3,4
O
GPIO5~6
AP programmable
B
(tri)
5~8
IODD[8:11]
2~5
IDE data bus 8~11
56,9
DVCC1~2
DGND1~2
6,43
7,42
P
P
Digital VCC
55,10
Digital ground
B
(tri)
I
(tri)
O
(tri)
O
(tri)
IODD[12:15]
CBLID_
CS1_
8~11
12
11~14
15
IDE data bus 12~15
Cable select input
Chip select 1
13
20
14
-
IDE address 2 / Serial data clock for EEPROM
DA2/SK
I
RESET#
RPU
15
16
22
23
Reset pin (***)
3.3v output
(pu)
A
24,31
25
AVCC0~1
DPF
17,24
18
P
Analog VCC
Full speed DP
High speed DP
B
B
B
26
DPH
19
27
DMF
20
21
Full speed DM
28
29,34
30
DMH
AGND0~1
RREF
X2
B
P
A
B
I
High speed DM
22,27
23
Analog ground
Reference resister connect (****)
Crystal output
25
32
26
33
X1
Crystal input, 12Mhz
I
(pd)
O
28
29
-
37
TEST
TEST mode input
Chip select 0
CS0_
(tri)
O
(tri)
O
30,31
-
38,39
21
DA0~1
DA2
IDE address 0~1
IDE address 2
(tri)
I
32
44
INTRQ
DMACK_
IORDY
IDE interrupt input
IDE acknowledge
IDE ready
(tri)
O
(tri)
33
45
I
34
46
(pu)
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 11
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
O
(tri)
O
(tri)
I
(pd)
B
(tri)
B
(tri)
35
36
47
48
DIOR_
IDE read signal
IDE write signal
IDE request
DIOW_
37
50
DMARQ
IODD[0:3]
IODD[4:7]
GPIO1
38~41
44~47
48
51~54
57~60
61
IDE data bus 0~3
IDE data bus 4~7
GPIO1
B
(tri)
-
-
-
62
63
64
O
O
O
PWR_CTL
F_LED
Power control
Full speed LED
High speed LED
H_LED
2,16~19,
35,49,
-
-
NC
No connection
(*) The different of I/O 8 type from I/O 16 type is the typical drive current. The typical drive current of
I/O 8 type is 8 mA, and for I/O pad 16 is 16 mA.
(**) When operating in default mode: GPIO7 is the ATA/ ATAPI reset input,
(***) When Reset pin is pulled low, the IDE bus will be in tri-state.
(****) RREF must be connected with a 510 ohm resister to ground.
Notation:
Type
O
Output
I
Input
B
Bi-directional
B/I
B/O
P
Bi-directional, default input
Bi-directional, default output
Power / Ground
A
Analog
SO
pu
pd
odpu
tri
Automatic output low when suspend
Internal pull up
Internal pull down
Open drain with internal pull up
Tri-state
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 12
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 4 BLOCK DIAGRAM
DMACK_
DIOR_
DIOW_
CS1_,
CS0_
DA2
DA1
DA0
CLK15
GPIO1
GPIO7
CPU
Control Register
RPU
8
CONTROL FIFO
CLK30
RXSTS
TXCTL
DPF
DPH
TXFIFO0
TXFIFO1
RXFIFO0
RXFIFO1
8/16-Bit
IDE
IODD15-0
SIE
UTMI USB2.0
LOGIC TXCVR
INTRQ
CBLID_
DMARQ
IORDY
4
Engine
DMF
16
DMH
12-96MHz
DATA
RREF
X10
X40
Clkgen
12MHz
Figure 4.1 - Block Diagram
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 13
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 5 FUNCTION DESCRIPTION
1. USB 2.0 TXCVR
The USB 2.0 Transceiver is the analog circuitry to handle the USB HS/FS signaling.
2. UTMI (USB 2.0 Transceiver Macrocell Interface) Logic
The UTMI Logic is compliant to Intel’s UTMI specification 1.01. This block handles the low level USB
protocol and signaling. The major jobs of UTMI Logic is data and clock recovery, NRZI encoding/decoding,
Bit Stuffing/De-stuffing, USB2.0 test modes supporting and serial / parallel conversion.
3. SIE (Serial Interface Engine)
The SIE contains the USB packet ID and address recognition logic, and other sequencing and state machine
logic to handle USB packets and transactions.
4. PLL
10XPLL provides the 120MHz clock output for UTMI Logic block. UTMI operates in 120MHz for USB HS
data processing. 40XPLL block will provide 480MHz for USB HS data transmission.
5. CLKGEN
CLKGEN is the clock generator block for the logic blocks. It generates 15MHz clock for micro controller,
48MHz for MDMA mode, 96MHz for UDMA mode, and 30MHz clock for UTMI, SIE, and FIFO.
6. CPU
The CPU is the control center of GL811E. It’s an 8-bit micro controller operating in 15MHz, 7.5 MIPS. After
receiving a USB command, it decodes the host command, then it re-assigns tasks to the IDE engine, GPIO,
FIFO, and response proper data/status to USB host.
7. IDE Engine
The IDE engine is extended from standard ATA / ATAPI protocol. It supports multiword DMA mode, and ultra
DMA mode data transfers.
8. FIFOs
Control FIFO is used as Control Read / Write FIFO. TXFIFO0 / TXFIFO1 are two sets of 512-byte ping-pong
FIFO for Bulk Read endpoint. It buffers data from IDE engine, and re-direct to USB SIE logic. RXFIFO0 /
RXFIFO1 are two sets of 512-byte ping-pong FIFO for Bulk Write endpoint. It buffers data from USB SIE
logic, and re-direct to IDE engine.
9. Control Registers
Control Register configures GL811E to proper operation. For example, CPU can set register to generate
wakeup event, enter suspend, transmits proper USB packet to host.
10. ATA/ATAPI
The GL811E complies with ATA/ATAPI-6 specification rev. 1.0. Please refer to the specifications for more information.
11. USB 2.0
The GL811E complies with Universal Serial Bus specification rev. 2.0, and it integrates Genesys Logic own
design UTMI transceiver that fully complies with the USB 2.0 Transceiver Macercell Interface (UTMI)
specification rev. 1.01. Please refer to the specifications for more information.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 14
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 6 ELECTRICAL CHARACTERISTICS
6.1 Absolute Maximum Ratings
Table 6.1 - Maximum Ratings
Symbol
VCC
Parameter
Min.
+3.0
-0.3
-0.3
-0.3
4000
0
Max.
+3.6
Unit
V
DC supply voltage
DC input voltage
VI
VCC + 0.3
VCC + 0.3
VCC + 0.3
V
VI/O
DC input voltage range for I/O
DC input voltage for USB D+/D- pins
Static discharge voltage
V
VAI/O
VESD
TA
V
V
Ambient Temperature
100
oC
6.2 Temperature Conditions
Table 6.2 - Temperature Conditions
Item
Value
Storage Temperature
Operating Temperature
-50oC ~ 150 oC
0 oC ~ 70 oC
6.3 DC Characteristics
6.3.1 I/O 8 Type digital pins (For pad type I/O 8 @ VCC=3.6V)
Table 6.3 - I/O 8 Type digital pins (For pad type I/O 8 @ VCC=3.6V)
Parameter
Current sink @ VOL = 0.4V
Min.
7.79
Typ.
10.83
19.87
0.50
Max.
14.09
23.39
0.80
Unit
mA
mA
V/ns
V/ns
V
Current output @ VOH = 2.4V (TTL high)
Falling slew rate at 30 pF loading capacitance
Rising slew rate at 30 pF loading capacitance
Input high threshold voltage
16.36
0.26
0.30
0.57
0.91
1.64
Input low threshold voltage
1.36
-
V
Hysteresis voltage
0
-
V
Leakage current for pads with internal pull up or pull
down resistor
46
mA
Pad internal pull down resister
Pad internal pull up resister
Supply current
51K
85K
105K
168K
152K
251K
109
Ohms
Ohms
mA
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 15
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
6.3.2 I/O 16 Type digital pins (For pad type I/O 16 @ VCC=3.6V)
Table 6.4 - I/O 16 Type digital pins (For pad type I/O 16 @ VCC=3.6V)
Parameter
Current sink @ VOL = 0.4V
Min.
16.20
24.13
0.51
Typ.
21.90
29.46
0.93
Max.
27.68
34.80
1.35
Unit
mA
mA
V/ns
V/ns
V
Current output @ VOH = 2.4V (TTL high)
Falling slew rate at 30 pF loading capacitance
Rising slew rate at 30 pF loading capacitance
Input high threshold voltage
0.46
0.83
1.27
2.15
Input low threshold voltage
0.89
51K
V
Pad internal pull down resister
105K
152K
Ohms
6.3.3 D+/ D- (For pad type u20mia @ VCC=3.6V)
Table 6.5 - D+/ D- (For pad type u20mia @ VCC=3.6V)
Parameter
Min.
0
Typ.
Max.
0.3
Unit
V
D+/D- static output LOW (RL of 1.5K to VCC
)
D+/D- static output HIGH (RL of 15K to GND )
Differential input sensitivity
Single-ended receiver threshold
Transceiver capacitance
2.8
0.2
0.8
3.6
V
V
2.0
20
V
pF
Hi-Z state data line leakage
-10
28
+10
43
mA
Ohms
Driver output resistance
6.3.4 Switching Characteristics
Table 6.6 - Switching Characteristics
Parameter
Min.
Typ.
12
Max.
Unit
MHz
ns
X1 crystal frequency
11.97
12.03
X1 cycle time
83.3
D+/D- rise time with 50pF loading
D+/D- fall time with 50pF loading
4
4
20
20
ns
ns
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 16
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
6.4 AC Characteristics- ATA/ ATAPI
The GL811E complies with ATA / ATAPI-6 specification rev 1.0, which supports following data transfer modes:
1. DMA (Direct Memory Access) data transfer:
DMA data transfer means of data transfer between device and host memory without host processor
intervention.
- Multiword DMA: Multiword DMA is a data transfer protocol used with the READ DMA, WRITE
DMA, READ DMA QUEUED, WRITE DMA QUEUED and PACKET commands. When a
Multiword DMA transfer is enabled as indicated by IDENTIFY DEVICE or IDENTIFY PACKET
DEVICE data, this data transfer protocol shall be used for the data transfers associated with these
commends. (Please refer to the ATA / ATAPI-6 specification rev 1.0 for more information.)
- Ultra DMA: Ultra DMA Is a data transfer protocol used with the READ DMA, WRITE DMA,
READ DMA QUEUED, WRITE DMA QUEUED and PACKET commands. When this protocol is
enabled, the Ultra DMA protocol shall be used instead of the Multiword DMA protocol when these
commands are issued by the host. This protocol applies to the Ultra DMA data burst only. (Please
refer to the ATA / ATAPI-6 specification rev 1.0 for more information.)
Following listed the symbols and their respective definitions that are used in the timing diagram:
-
-
-
-
-
-
-
Signal transition (asserted or negated)
Data transition (asserted or negated)
Data valid
Undefined but not necessarily released
Asserted, negated or released
Released
The “other” condition if a signal is shown with no change
All signals are shown with the asserted condition facing to the top of the page. The negated condition is shown
towards the bottom of the page relative to the asserted condition.
The interface uses a mixture of negative and positive signals for control and data. The terms asserted and
negated are used for consistency and are independent of electrical characteristics.
In all timing diagrams, the lower line indicates negated, and the upper line indicates asserted. The following
illustrates the representation of a signal named Test going from negated to asserted and back to negated, based
on the polarity of the signal.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 17
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
6.4.1 Register Transfers
Notes:
1. Device address consists of signals CS0_, CS1_ and DA(2:0).
2. Data consists of IODD(7:0).
3. The negation of IORDY by the device is used to extend the register transfer cycle. The determination of
whether the cycle is to be extended is made by the host after tA from the assertion of DIOR_ or DIOW_.
The assertion and negation of IORDY are described as following:
3.1 Device never negates IORDY, devices keeps IORDY released: no wait is generated.
3.2 Device negates IORDY before tA, but causes IORDY to be asserted before tA. IORDY is released
prior to negation and may be asserted for no more than 5 ns before release: no wait generated.
3.3 Device negates IORDY before tA, IORDY is released prior to negation and may be asserted for no
more than 5 ns before release: wait generated. The cycle completes after IORDY is released. For
cycles where a wait is generated and DIOR_ is asserted, the device shall read data on IODD(0:7) for
tRD before asserting IORDY.
4.DMACK_ shall remain negated during a register transfer.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 18
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Register transfer timing parameters
Timing (ns)
t0
t1
t2
t2i
t3
t4
t5
t6
Cycle time
2000
1000
300
900
80
Address valid to DIOR_/ DIOW_ setup
DIOR_/ DIOW_ pulse width 8-bit
DIOR_/ DIOW_ recovery time
DIOW_ data setup
DIOW_ data hold
40
DIOR_ data setup
-
DIOR_ data hold
-
t6Z DIOR_ data tristate
-
t9
DIOR_/ DIOW_ to address valid hold
900
Read Data Valid to IORDY active
(if IORDY initially low after tA)
tRD
tA
tB
tC
IORDY Setup time
-
-
-
IORDY Pulse Width
IORDY assertion to release (max)
6.4.2 Multiword DMA data transfer
Register transfer timing parameters
Cycle time
Timing (ns)
t0
tD
tE
tF
tG
tH
tI
120
80
-
DIOR_/ DIOW_ asserted pulse width
DIOR_ data access
DIOR_ data hold
-
DIOR_/ DIOW_ data setup
DIOW_ data hold
40
18
18
20
36
36
-
DMACK to DIOR_/ DIOW_ setup
DIOR_/ DIOW_ to DMACK hold
tJ
tKR DIOR_ negated pulse width
tKW DIOW_ negated pulse width
tLR DIOR_ to DMARQ delay
tLW DIOW_ to DMARQ delay
-
tM
tN
tZ
CS(1:0) (max) valid to DIOR_/ DIOW_
CS(1:0) hold
36
18
-
DMACK_ to read data released
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 19
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Note:
The host shall not assert DMACK_ or negate both CS0_ and CS1_ until the assertion of DMARQ is detected.
The maximum time from the assertion of DMARQ to the assertion of DMACK_ or the negation of both CS0_
and CS1_ is not defined.
Figure 6.1 - Initiating a Multiword DMA Data Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 20
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Figure 6.2 - Sustaining a Multiword DMA Data Burst
Note:
To terminate the data burst, the Device shall negate DMARQ within the tL of the assertion of the current
DIOR_ or DIOW_ pulse. The last data word for the burst shall then be transferred by the negation of the
current DIOR_ or DIOW_ pulse. If all data for the command has not been transferred, the device shall reassert
DMARQ again at any later time to resume the DMA operation.
Figure 6.3 - Device Terminating a Multiword DMA Data Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 21
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Note:
1. To terminate the transmission of a data burst, the Host shall negate DMACK_ within the specified time
after a DIOR_ or DIOW_ pulse. No further DIOR_ or DIOW_ pulses shall be asserted for this burst.
2. If the device is able to continue the transfer of data, the device may leave DMARQ asserted and wait
for the host to reassert DMACK_ or may negate DMARQ at any time after detecting that DMACK_
has been negated.
Figure 6.4 - Host terminating a Multiword DMA Data Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 22
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
6.4.3 Ultra DMA data transfer
Table 6.7 - Ultra DMA data burst timing requirements
Mode 0
(in ns)
Mode 1
(in ns)
Mode 2
(in ns)
Mode 3
(in ns)
Mode 4
(in ns)
Name
Comment
min max min max min max min max Min max
Typical sustained average
two cycle time
Cycle time allowing for
asymmetry and clock
variations
Two cycle time allowing
for clock variations
Data setup time at
recipient
t2CYCTYP
tCYC
240
112
230
160
73
120
54
90
39
86
60
25
57
t2CYC
154
115
tDS
15
5
10
5
7
7
5
5
6
Data hold time at recipient
tDH
tDVS
5
5
Data valid setup time at
sender
70
48
30
20
Data valid hold time at
sender
tDVH
6
6
6
6
6
First STORBE time
tFS
tLI
0
0
230
150
0
0
200
150
0
0
170
150
0
0
130
100
0
0
120
100
Limited interlock time
Interlock time with
minimum
tMLI
tUI
20
0
20
0
20
0
20
0
20
0
Unlimited interlock time
Maximum time allowed
for output drivers to
release
tAZ
10
10
10
10
10
Minimum delay time
required for output
tZAH
20
20
20
20
20
Drivers to assert or negate
tZAD
tENV
0
0
0
0
0
Envelope time
20
70
50
20
70
30
20
70
20
20
55
20
55
STROBE to DMARDY_
time
tSR
NA
NA
Ready to final STROBE
time
Minimum time to assert
STOP or negate DMARQ
Maximum time before
releasing IORDY
Minimum time before
driving STROBE
Setup and hold times for
DMACK_
tRFS
75
70
60
60
20
60
20
tRP
160
125
100
100
100
tIORDYZ
tZIORDY
tACK
20
20
20
0
0
0
0
0
20
20
20
20
20
Time from STROBE edge
to negation of DMARQ or
assertion of STOP
tSS
50
50
50
50
50
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 23
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are not in efficient until DMARQ and DMACK are asserted.
Figure 6.5 - Initiating an Ultra DMA Data-In Burst
Notes:
IODD(15:0) and DSTROBE signals are shown at both the host and the device to emphasize that cable settling
time as well as cable propagation delay shall not allow the data signals to be considered stable at the host until
some time after they are driven by the device.
Figure 6.6 - Sustained Ultra DMA Data-In Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 24
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
1. The host may assert STOP to request termination of the Ultra DMA burst no sooner than tRP after
HDMARDY_ is negated.
2. If the tSR timing is not satisfied, the host may receive zero, one, or two more data words from the device.
Figure 6.7 - Host Pausing an Ultra DMA Data-In Burst
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are no longer in effect after DMARQ and DMACK are
negated.
Figure 6.8 - Device Terminating an Ultra DMA Data-In Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 25
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are no longer in effect after DMARQ and DMACK are
negated.
Figure 6.9 - Host Terminating an Ultra DMA Data-In Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 26
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are not in effect until DMARQ and DMACK are asserted.
Figure 6.10 - Initiating an Ultra DMA Data-Out Burst
Notes:
IODD(15:0) and HSTROBE signals are shown at both the device and the host to emphasize that cable settling
time as well as cable propagation delay shall not allow the data signals to be considered stable at the devicet
until some time after they are driven by the host.
Figure 6.11 - Sustained Ultra DMA Data-Out Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 27
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
1. The device may negate DMARQ to request termination of the Ultra DMA burst no sooner than tRP after
DDMARDY_ is negated.
2. If the tSR timing is not satisfied, the device may receive zero, one, or two more data words from the host.
Figure 6.12 - Device Pausing an Ultra DMA Data-Out Burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 28
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are no longer in effect after DMARQ and DMACK are
negated.
Figure 6.13 - Host terminating an Ultra DMA data-out burst
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 29
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
Notes:
The definitions for the DIOW_:STOP, DIOR_:HDMARDY_:HSTROBE and
IORDY:DDMARDY_:DSTROBE signal lines are no longer in effect after DMARQ and DMACK are
negated.
Figure 6.14 - Device Terminating an Ultra DMA Data-Out Burst
6.5 AC Characteristics - USB 2.0
The GL811E conforms to all timing diagrams and specifications for Universal Serial Bus specification rev. 2.0.
Please refer to this specification for more information.
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 30
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 7 PACKAGE DIMENSION
D
D1
D2
A
A2
D
A1
25
36
37
24
B
A
GL811E
YYWW XXXXX-XX
Date Code
Lot Code
Version
No.
48
13
4X
aaa C A B D
1
12
4X
bbb H A B D
e
c
b
s s
D
ddd M C A
B
-
01
-
0
C
SEATING
PLANE
ccc
C
CONTROL DIMENSIONS ARE IN MILLIMETERS.
MILLIMETER
MIN. NOM. MAX. MIN. NOM. MAX.
INCH
SYMBOL
-02
-03
A
A1
A2
D
1.60
0.063
0.006
R1
R2
0.05
1.35
0.15 0.002
1.40
1.45 0.053 0.055 0.057
0.354 BASIC
0.354 BASIC
0.276 BASIC
0.276 BASIC
0.217 BASIC
0.217 BASIC
0.003
9.00 BASIC
9.00 BASIC
7.00 BASIC
7.00 BASIC
5.50 BASIC
5.50 BASIC
H
E
GAGE PLANE
D1
E1
D2
E2
R1
R2
0.25mm
S
L
0.08
0.08
0°
0.20 0.003
7°
0.008
7°
-
0
3.5°
0°
0°
11°
11°
3.5°
-
01
0°
NOTES :
-
02
11°
11°
0.09
0.45
12°
12°
13°
13°
0.20 0.004
0.75 0.018 0.024 0.030
0.039 REF
12°
12°
13°
13°
0.008
-03
1. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
c
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm
PER SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY
SIZE DIMENSIONS INCLUDING MOLD MISMATCH.
L
L1
S
b
e
0.60
1.00 REF
0.20
0.17
0.008
0.20
0.27 0.007 0.008 0.011
0.020 BASIC
2. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE
MAXIMUM b DIMENSION BY MORE THAN 0.08mm.
DAMBAR CAN NOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD IS 0.07mm.
0.50 BASIC
TOLERANCES OF FORM AND POSITION
aaa
bbb
ccc
ddd
0.20
0.20
0.08
0.08
0.008
0.008
0.003
0.003
Figure 7.1 - GL811E 48 Pin LQFP Package
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 31
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
D
D1
A
A2
D2
D
A1
25
36
37
24
B
A
GL811E
YYWW XXXXX-XX
Date Code
Lot Code
Version
No.
48
13
4X
aaa C A B D
1
12
4X
bbb H A B D
e
c
b
s s
D
ddd M C A
B
-
01
-
0
C
SEATING
PLANE
ccc
C
CONTROL DIMENSIONS ARE IN MILLIMETERS.
MILLIMETER
MIN. NOM. MAX. MIN. NOM. MAX.
INCH
SYMBOL
-02
-03
A
A1
A2
D
1.20
0.047
0.006
R1
R2
0.05
0.95
0.15 0.002
1.00
1.05 0.037 0.039 0.041
0.354 BASIC
0.354 BASIC
0.276 BASIC
0.276 BASIC
0.217 BASIC
0.217 BASIC
0.003
9.00 BASIC
9.00 BASIC
7.00 BASIC
7.00 BASIC
5.50 BASIC
5.50 BASIC
H
E
GAGE PLANE
D1
E1
D2
E2
R1
R2
0.25mm
S
L
0.08
0.08
0°
0.20 0.003
7°
0.008
7°
-
0
3.5°
0°
0°
11°
11°
3.5°
-
01
0°
NOTES :
-
02
11°
11°
0.09
0.45
12°
12°
13°
13°
0.20 0.004
0.75 0.018 0.024 0.030
0.039 REF
12°
12°
13°
13°
0.008
-03
1. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
c
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm
PER SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY
SIZE DIMENSIONS INCLUDING MOLD MISMATCH.
L
L1
S
b
e
0.60
1.00 REF
0.20
0.17
0.008
0.20
0.27 0.007 0.008 0.011
0.020 BASIC
2. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE
MAXIMUM b DIMENSION BY MORE THAN 0.08mm.
DAMBAR CAN NOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD IS 0.07mm.
0.50 BASIC
TOLERANCES OF FORM AND POSITION
aaa
bbb
ccc
ddd
0.20
0.20
0.08
0.08
0.008
0.008
0.003
0.003
Figure 7.2 - GL811E 48 Pin TQFP Package
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 32
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
D
D1
A
A2
D2
D
A1
48
33
49
32
B
A
GL811E
YYWW XXXXX-XX
Date Code
Lot Code
Version
No.
17
64
0-1
4X
aaa C A B D
16
4X
1
bbb H A B D
e
c
s s
D
ddd M C A
B
b
-0
SEATING
PLANE
C
ccc
C
CONTROL DIMENSIONS ARE IN MILLIMETERS.
-02
-03
MILLIMETER
MIN. NOM. MAX. MIN. NOM. MAX.
INCH
SYMBOL
R1
A
A1
A2
D
1.60
0.15 0.002
0.063
0.006
0.05
1.35
R2
1.40
1.45 0.053 0.055 0.057
0.472 BASIC
0.472 BASIC
0.393 BASIC
0.393 BASIC
0.295 BASIC
0.295 BASIC
0.003
H
12.00 BASIC
12.00 BASIC
10.00 BASIC
10.00 BASIC
7.50 BASIC
7.50 BASIC
GAGE PLANE
E
0.25mm
S
L
D1
E1
D2
E2
R1
R2
0.08
0.08
0
0
11
11
0.09
0.45
0.20 0.003
7
0.008
7
-
0
3.5
0
0
11
11
3.5
-
01
0-2
0-3
c
NOTES :
12
12
13
13
12
12
13
13
0.008
1.
2.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm PER
SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE
DIMENSIONS INCLUDING MOLD MISMATCH.
0.20 0.004
0.75 0.018 0.024 0.030
0.039 REF
L
L1
S
b
e
0.60
1.00 REF
DIMENSION b DOES NOT INCLUDE DAMBAR
0.20
0.17
0.008
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE
MAXIMUM b DIMENSION BY MORE THAN 0.08mm.
DAMBAR CAN NOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD IS 0.07mm.
0.20
0.27 0.007 0.008 0.011
0.020 BASIC
0.50 BASIC
TOLERANCES OF FORM AND POSITION
aaa
bbb
ccc
ddd
0.20
0.20
0.08
0.08
0.008
0.008
0.003
0.003
Figure 7.3 - GL811E 64 Pin LQFP Package
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 33
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
D
D1
A
A2
D2
D
A1
48
33
49
32
B
A
GL811E
YYWW XXXXX-XX
Date Code
Lot Code
Version
No.
17
64
0-1
4X
aaa C A B D
16
4X
1
bbb H A B D
e
c
s s
D
ddd M C A
B
b
-0
SEATING
PLANE
C
ccc
C
CONTROL DIMENSIONS ARE IN MILLIMETERS.
-02
-03
MILLIMETER
MIN. NOM. MAX. MIN. NOM. MAX.
INCH
SYMBOL
R1
A
A1
A2
D
1.20
0.15 0.002
0.047
0.006
0.05
0.95
R2
1.00
1.05 0.037 0.039 0.041
0.472 BASIC
0.472 BASIC
0.393 BASIC
0.393 BASIC
0.295 BASIC
0.295 BASIC
0.003
H
12.00 BASIC
12.00 BASIC
10.00 BASIC
10.00 BASIC
7.50 BASIC
7.50 BASIC
GAGE PLANE
E
0.25mm
S
L
D1
E1
D2
E2
R1
R2
0.08
0.08
0
0
11
11
0.09
0.45
0.20 0.003
7
0.008
7
-
0
3.5
0
0
11
11
3.5
-
01
0-2
0-3
c
NOTES :
12
12
13
13
12
12
13
13
0.008
1.
2.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 mm PER
SIDE. D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE
DIMENSIONS INCLUDING MOLD MISMATCH.
0.20 0.004
0.75 0.018 0.024 0.030
0.039 REF
L
L1
S
b
e
0.60
1.00 REF
DIMENSION b DOES NOT INCLUDE DAMBAR
0.20
0.17
0.008
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED THE
MAXIMUM b DIMENSION BY MORE THAN 0.08mm.
DAMBAR CAN NOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD IS 0.07mm.
0.20
0.27 0.007 0.008 0.011
0.020 BASIC
0.50 BASIC
TOLERANCES OF FORM AND POSITION
aaa
bbb
ccc
ddd
0.20
0.20
0.08
0.08
0.008
0.008
0.003
0.003
Figure 7.4 - GL811E 64 Pin TQFP Package
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 34
GL811E USB 2.0 to ATA/ATAPI Bridge Controller
CHAPTER 8 ORDERING INFORMATION
Table 8.1 - Ordering Information
Package
Part Number
Status
48-pin LQFP
64-pin LQFP
48-pin TQFP
64-pin TQFP
GL811E
©2000-2005 Genesys Logic Inc. - All rights reserved.
Page 35
相关型号:
©2020 ICPDF网 联系我们和版权申明