G916-450T1UF [GMT]
300mA High PSRR, Low Noise, LDO Regulators; 300毫安高PSRR ,噪声低, LDO稳压器型号: | G916-450T1UF |
厂家: | GLOBAL MIXED-MODE TECHNOLOGY INC |
描述: | 300mA High PSRR, Low Noise, LDO Regulators |
文件: | 总13页 (文件大小:480K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Global Mixed-mode Technology Inc.
G916
300mA High PSRR, Low Noise, LDO Regulators
Features
General Description
Low, 90µA No-Load Supply Current
Guaranteed 300mA Output Current
Dropout Voltage is 200mV @ 150mA Load
PSRR=65dB @ 120Hz; 55dB @ 1kHz
Over-Temperature Protection and Short-Circuit
Protection
The G916 series is a low supply current, high PSRR,
low noise, and low dropout linear regulator that comes
in a space saving TSOT-23-5, SOT-23-5 package.
The supply current at no-load is 90µA. In the shutdown
mode, the maximum supply current is less than 1µA.
Operating voltage range is from 2.5V to 6.0V. The
over-current protection limit is set at 550mA typical. An
over- temperature protection circuit is built-in in the
Device to prevent thermal overload. These power
saving features make the G916 series ideal for use in
the battery-powered applications such as notebook
computers, cellular phones, and PDA’s.
Fixed Mode: 1.20V~5.00V (G916-XXX)
Adjustable Mode: from 1.25V to 5.50V (G916)
Max. Supply Current in Shutdown Mode < 1µA
Low Output Noise at 28µVRMS with bypass Ca-
pacitor
Stable with low cost ceramic capacitors
The G916 has two modes of operation. When the SET
pin is connected to ground, its output is a pre-set value:
3.3V. There is no external component needed. When an
output other than the preset value is needed, two ex-
ternal resistors should be used as a voltage divider. The
output voltage is then adjusted by the resistor ratio.
G916-XXX is with fixed-mode output. The output voltage
range is from 1.2V to 5.0V.
Applications
Notebook Computers
Cellular Phones
PDAs
Digital still Camera and Video Recorders
Hand-Held Devices
Audio Codec
Pin Configuration
OUTPUT
VOLTAGE
OUT
IN
OUT
SET
IN
1
5
4
R1
R2
+
-
G916
SET
2
3
GND
G916
CIN
1µF
SHDN
BATTERY
COUT
1µF
GND
SHDN
SOT-23-5、TSOT-23-5
Adjustable mode
OUT
BYP
IN
1
5
4
OUTPUT
VOLTAGE
IN
OUT
BYP
G916-XXX
SHDN
+
CIN
2
3
GND
COUT
1µF
G916-XXX
_ 1µF
BATTERY
CBYP
10nF
GND
SHDN
SOT-23-5、TSOT-23-5
Fixed mode
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
1
Global Mixed-mode Technology Inc.
Ordering Information
G916
ORDER
NUMBER
ORDER NUMBER
(Pb free)
TEMP.
RANGE
MARKING
VOLTAGE
PACKAGE
G916-250TOU
G916-270TOU
G916T1U
G916-120T1U
G916-330T1U
G916-250TOUf
G916-270TOUf
G916T1Uf
G916-120T1Uf
G916-330T1Uf
96ANx
96APx
16xx
96AAx
6Axx
2.50V
2.70V
Adjustable
1.20V
TSOT-23-5
TSOT-23-5
SOT-23-5
SOT-23-5
SOT-23-5
-40°C~ +85°C
-40°C~ +85°C
-40°C~ +85°C
-40°C~ +85°C
-40°C~ +85°C
3.30V
For other output voltage, please contact us at sales@gmt.com.tw
Note: TO: TSOT-23-5
U: Tape & Reel
T1: SOT-23-5
Selector Guide
ORDER NUMBER
ORDER NUMBER
OUTPUT VOLTAGE (V)
MARKING
(Pb free)
G916TOU
G916TOUf
Adjustable
1.20
1.30
1.40
1.50
1.60
1.70
1.80
1.90
2.00
2.10
2.20
2.30
2.40
2.50
2.60
2.70
2.80
2.85
2.90
3.00
3.10
3.15
3.20
3.30
3.40
3.50
3.60
3.70
3.80
3.90
4.00
4.10
4.20
4.30
4.40
4.50
4.60
4.70
4.75
4.80
4.90
5.00
16xx
96AAx
96ABx
96ACx
96ADx
96AEx
96AFx
96AGx
96AHx
96AIx
96AJx
96AKx
96ALx
96AMx
96ANx
96AOx
96APx
96AQx
96ARx
96ASx
96ATx
96AUx
96AVx
96AWx
6Axx
96AYx
96AZx
96BAx
96BBx
96BCx
96BDx
96BEx
96BFx
96BGx
96BHx
96BIx
96BJx
96BKx
96BLx
96BMx
96BNx
96BOx
96BPx
G916-120TOU
G916-130TOU
G916-140TOU
G916-150TOU
G916-160TOU
G916-170TOU
G916-180TOU
G916-190TOU
G916-200TOU
G916-210TOU
G916-220TOU
G916-230TOU
G916-240TOU
G916-250TOU
G916-260TOU
G916-270TOU
G916-280TOU
G916-285TOU
G916-290TOU
G916-300TOU
G916-310TOU
G916-315TOU
G916-320TOU
G916-330TOU
G916-340TOU
G916-350TOU
G916-360TOU
G916-370TOU
G916-380TOU
G916-390TOU
G916-400TOU
G916-410TOU
G916-420TOU
G916-430TOU
G916-440TOU
G916-450TOU
G916-460TOU
G916-470TOU
G916-475TOU
G916-480TOU
G916-490TOU
G916-500TOU
G916-120TOUf
G916-130TOUf
G916-140TOUf
G916-150TOUf
G916-160TOUf
G916-170TOUf
G916-180TOUf
G916-190TOUf
G916-200TOUf
G916-210TOUf
G916-220TOUf
G916-230TOUf
G916-240TOUf
G916-250TOUf
G916-260TOUf
G916-270TOUf
G916-280TOUf
G916-285TOUf
G916-290TOUf
G916-300TOUf
G916-310TOUf
G916-315TOUf
G916-320TOUf
G916-330TOUf
G916-340TOUf
G916-350TOUf
G916-360TOUf
G916-370TOUf
G916-380TOUf
G916-390TOUf
G916-400TOUf
G916-410TOUf
G916-420TOUf
G916-430TOUf
G916-440TOUf
G916-450TOUf
G916-460TOUf
G916-470TOUf
G916-475TOUf
G916-480TOUf
G916-490TOUf
G916-500TOUf
TO: TSOT-23-5
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
2
Global Mixed-mode Technology Inc.
Selector Guide
G916
ORDER NUMBER
(Pb free)
ORDER NUMBER
OUTPUT VOLTAGE (V)
MARKING
G916T1U
G916T1Uf
Adjustable
1.20
1.30
1.40
1.50
1.60
1.70
1.80
1.90
2.00
2.10
2.20
2.30
2.40
2.50
2.60
2.70
2.80
2.85
2.90
3.00
3.10
3.15
3.20
3.30
3.40
3.50
3.60
3.70
3.80
3.90
4.00
4.10
4.20
4.30
4.40
4.50
4.60
4.70
4.75
4.80
4.90
5.00
16xx
96AAx
96ABx
96ACx
96ADx
96AEx
96AFx
96AGx
96AHx
96AIx
96AJx
96AKx
96ALx
96AMx
96ANx
96AOx
96APx
96AQx
96ARx
96ASx
96ATx
96AUx
96AVx
96AWx
6Axx
96AYx
96AZx
96BAx
96BBx
96BCx
96BDx
96BEx
96BFx
96BGx
96BHx
96BIx
96BJx
96BKx
96BLx
96BMx
96BNx
96BOx
96BPx
G916-120T1U
G916-130T1U
G916-140T1U
G916-150T1U
G916-160T1U
G916-170T1U
G916-180T1U
G916-190T1U
G916-200T1U
G916-210T1U
G916-220T1U
G916-230T1U
G916-240T1U
G916-250T1U
G916-260T1U
G916-270T1U
G916-280T1U
G916-285T1U
G916-290T1U
G916-300T1U
G916-310T1U
G916-315T1U
G916-320T1U
G916-330T1U
G916-340T1U
G916-350T1U
G916-360T1U
G916-370T1U
G916-380T1U
G916-390T1U
G916-400T1U
G916-410T1U
G916-420T1U
G916-430T1U
G916-440T1U
G916-450T1U
G916-460T1U
G916-470T1U
G916-475T1U
G916-480T1U
G916-490T1U
G916-500T1U
G916-120T1Uf
G916-130T1Uf
G916-140T1Uf
G916-150T1Uf
G916-160T1Uf
G916-170T1Uf
G916-180T1Uf
G916-190T1Uf
G916-200T1Uf
G916-210T1Uf
G916-220T1Uf
G916-230T1Uf
G916-240T1Uf
G916-250T1Uf
G916-260T1Uf
G916-270T1Uf
G916-280T1Uf
G916-285T1Uf
G916-290T1Uf
G916-300T1Uf
G916-310T1Uf
G916-315T1Uf
G916-320T1Uf
G916-330T1Uf
G916-340T1Uf
G916-350T1Uf
G916-360T1Uf
G916-370T1Uf
G916-380T1Uf
G916-390T1Uf
G916-400T1Uf
G916-410T1Uf
G916-420T1Uf
G916-430T1Uf
G916-440T1Uf
G916-450T1Uf
G916-460T1Uf
G916-470T1Uf
G916-475T1Uf
G916-480T1Uf
G916-490T1Uf
G916-500T1Uf
T1: SOT-23-5
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
3
Global Mixed-mode Technology Inc.
G916
Absolute Maximum Ratings
IN to GND. . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
Output Short-Circuit Duration . . . . . . . . . . . . .Infinite
SET, BYP to GND . . . . . . . . . . . . . . . . . -0.3V to 7V
Operating Temperature Range . . . . . . .-40°C to 85°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . 150°C
Thermal Resistance Junction to Ambient, (θJA)
SOT-23-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°C/W(1)
TSOT-23-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . .196°C/W
Storage Temperature Range . . . . . . . . .-65°C to 160°C
Reflow Temperature (soldering, 10sec) . . . . . . . .260°C
SHDN to GND . . . . . . . . . . . . . . . . . . .-0.3V to 7V
SHDN to IN . . . . . . . . . . . . . . . . . . . . .-7V to 0.3V
OUT to GND . . . . . . . . . . . . . ..-0.3V to (VIN + 0.3V)
Note (1): See Recommended Minimum Footprint
Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Electrical Characteristics
(VIN =3.6V, V SHDN =VIN, TA =25°C, unless otherwise noted.) (Note 1)
PARAMETER
Input Voltage (Note 2)
SYMBOL
VIN
CONDITION
MIN TYP MAX UNIT
2.5
-2
---
---
---
---
---
---
---
6.0
2
V
Output Voltage Accuracy (adjustable mode)
VOUT
Variation from specified VOUT, IOUT=1mA
VOUT ≥2.50V, IOUT =1mA
%
-2
2
Output Voltage Accuracy (fixed mode)
VOUT
%
2.50V>VOUT ≥1.80V, IOUT=1mA
1.80V>VOUT ≥1.20V, IOUT=1mA
-3
3
-4
4
Adjustable Output Voltage Range (Note 3)
Maximum Output Current
Current Limit (Note 4)
VOUT
VSET
300
5.5
---
---
---
---
V
mA
mA
mA
µA
ILIM
Isc
IQ
400 550
Short Circuit Current
---
---
---
---
---
---
---
---
---
280
90
Ground Pin Current
VOUT=1.50V
VOUT=1.80V
VOUT=2.50V
1.36 1.7
1.10 1.4
0.58 0.8
0.41 0.5
0.36 0.5
0.25 0.5
0.24 0.5
Dropout Voltage (Note 5)
VDROP IOUT =300mA
V
VOUT=3.00V
VOUT=3.30V
VOUT=4.75V
V
OUT=5.00V
SET=GND, VIN=V(STD)+0.1V to 6.2V
IOUT=10mA
Line Regulation
ΔVLNR
ΔVLDR
---
0.06 0.12 %/V
--- 0.02 %/mA
Load Regulation
IOUT=10mA to 300mA
---
---
---
Ripple Rejection
PSRR F=120Hz, 0.45VP-P, IOUT=10mA
65
28
---
dB
Output Voltage Noise (10Hz to 100kHz)
en
COUT=1µF, IOUT=1mA, CBYP=10nF
--- µVRMS
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
4
Global Mixed-mode Technology Inc.
G916
Electrical Characteristics (continued)
(VIN =3.6V, V SHDN =VIN, TA =25°C, unless otherwise noted.) (Note 1)
PARAMETER
SHUTDOWN
SYMBOL
CONDITION
MIN TYP MAX UNIT
VIH
VIL
Regulator enabled
Regulator shutdown
1.5
---
---
---
---
SHDN Input Threshold
V
0.4
I
SHDN
V SHDN = VIN
TA = +25°C
TA = +25°C
SHDN Input Bias Current
Shutdown Supply Current
SET INPUT
--- 0.003 0.1
--- 0.2
µA
µA
IQSHDN VOUT = 0V
1
VIN = 2.5V to 5.5V,
OUT = 1mA
TA = +25°C
1.225 1.25 1.275
SET Reference Voltage (Note 3)
VSET
ISET
V
I
TA = TMIN to TMAX
TA = +25°C
---
---
1.25 ---
SET Input Leakage Current (Note 3)
THERMAL PROTECTION
VSET = 1.3V
5
30
nA
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
TSHDN
---
---
145
25
---
---
°C
°C
ΔTSHDN
Note 1: Limits is 100% production tested at TA= +25°C. Low duty pulse techniques are used during test to maintain junc-
tion temperature as close to ambient as possible.
Note 2: Guaranteed by line regulation test.
Note 3: Adjustable mode only.
Note 4:
Not tested. For design purposes, the current limit should be considered 400mA minimum to 650mA maximum.
Note 5: The dropout voltage is defined as (VIN-VOUT) when VOUT is 100mV below the target value of VOUT. The performance of
every G916 part, see “Typical Performance Characteristics”.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
5
Global Mixed-mode Technology Inc.
G916
Typical Performance Characteristics
(VIN =5V, CIN=1µF, COUT=1µF, V SHDN = VIN, G916-475, TA =25°C, unless otherwise noted.)
Line Transient
Load Transient
Short Circuit Current
Ripple Rejection
90
80
70
60
50
40
30
20
10
0
10mA
300mA
100mA
V =4V ; COUT=1 F ;
µ
IN
CBYP=10nF ; Vr=245mV
0.01
0.1
1
10
100
Frequency (KHz)
Turn-On
Turn-Off
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
6
Global Mixed-mode Technology Inc.
Typical Performance Characteristics (continued)
G916
Dropout Voltage vs. IL
Overcurrent Protection Characteristics
300
250
200
150
100
50
T =85 C
°
A
T =25 C
°
A
T =-25 C
°
A
0
0
50
100
150
IL (mA)
200
250
300
Output Voltage vs. Temperature
Output Noise
5.2
5.1
5.0
4.9
4.8
4.7
4.6
4.5
4.4
4.3
4.2
IL=10mA
VIN=5.5V
VIN=5.0V
-25 -15 -5
5
15 25 35 45 55 65 75 85
Temperature ( C)
°
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
7
Global Mixed-mode Technology Inc.
Pin Description
G916
PIN
G916-XXX
NAME
FUNCTION
G916
1
1
IN
Regulator Input. Supply voltage can range from +2.5V to +6.0V. Bypass with 1µF to GND
Ground. This pin also functions as a heatsink. Solder to large pads or the circuit board
ground plane to maximize thermal dissipation.
2
3
2
GND
Active-Low Shutdown Input. A logic low reduces the supply current to less than 1µA. Connect to IN
for normal operation.
SHDN
3
Feedback Input for Setting the Output Voltage. Connect to GND to set the output voltage to
4
SET the preset output voltage. Connect to an external resistor divider for adjustable-output op-
eration.
This is a reference bypass pin. It should connect external 10nF capacitor to GND to reduce
4
5
BYP
output noise. Bypass capacitor must be no less than 1nF. (CBYP≥ 1nF)
Regulator Output. Sources up to 300mA. Bypass with a 1µF, <0.2Ω typical ESR capacitor
5
OUT
to GND.
feedback voltage force to be the same as the 1.25V
bandgap reference. The output voltage, VOUT, is then
given by the following equation:
Detailed Description
The block diagram of the G916 is shown in Figure 1. It
consists of an error amplifier, 1.25V bandgap reference,
PMOS output transistor, internal feedback voltage divider,
mode comparator, shutdown logic, over current protec-
tion circuit, and over temperature protection circuit.
VOUT = 1.25 (1 + R1/R2).
(1)
Alternatively, the relationship between R1 and R2 is
given by:
The mode comparator compares the SET pin voltage
with an internal 350mV reference. If the SET pin volt-
age is less than 350mV, the internal feedback voltage
divider’s central tap is connected to the non-inverting
input of the error amplifier. The error amplifier com-
pares non-inverting input with the 1.25V bandgap ref-
erence. If the feedback voltage is higher than 1.25V,
the error amplifier’s output becomes higher so that the
PMOS output transistor has a smaller gate-to-source
voltage (VGS). This reduces the current carrying capa-
bility of the PMOS output transistor, as a result the
output voltage decreases until the feedback voltage is
equal to 1.25V. Similarly, when the feedback voltage is
less than 1.25V, the error amplifier causes the output
PMOS to source more current to pull the feedback
voltage up to 1.25V. Thus, through this feedback ac-
tion, the error amplifier, output PMOS, and the voltage
dividers effectively form a unity-gain amplifier with the
R1 = R2 (VOUT /1.25 - 1).
(2)
For the reasons of reducing power dissipation and
loop stability, R2 is chosen to be 100KΩ. For G916,
R1 is 164K, and the pre-set VOUT is 3.30V.
When external voltage divider is used, as shown in
Figure 2, the SET pin voltage will be larger than
350mV. The non-inverting input of the amplifier will be
connected to the external voltage divider. However,
the operation of the feedback loop is the same, so that
the conditions of Equations 1 and 2 are still true. The
output voltage is still given by Equation 1.
For G916-XXX, adjust the internal reference and in-
ternal voltage divider. It provides a fixed mode output
ranging from 1.2V to 5V.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
8
Global Mixed-mode Technology Inc.
G916
IN
SHDN
-
OVER CURRENT
PROTECT & DYNAMIC
FEEDBACK
P
ERROR
AMP
SHUTDOWN
LOGIC
+
OUT
SET
-
R1
OVER TEMP.
PROTECT
1.25V
Vref
+
+
-
350mV
R2
MODE COMPARATOR
GND
IN
SHDN
-
OVER CURRENT
PROTECT & DYNAMIC
FEEDBACK
P
ERROR
AMP
SHUTDOWN
LOGIC
+
OUT
R1
OVER TEMP.
PROTECT
1.25V
Vref
BYP
R2
GND
Figure 1. Functional Diagram of Adjustable-mode & Fixed mode
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
9
Global Mixed-mode Technology Inc.
G916
mount device, heat sinking is accomplished by using
the heat spreading capabilities of the PC board and its
copper traces. In the case of a SOT-23-5 package, the
thermal resistance is typically 240°C/Watt. (See Rec-
ommended Minimum Footprint). Refer to Figure 3a &
3b is the G916 valid operating region (Safe Operating
Area) & refer to Figure 4 is maximum power dissipa-
tion of SOT-23-5.
OUTPUT
VOLTAGE
OUT
IN
R1
R2
+
-
G916
SET
RL
SHDN
CIN
BATTERY
COUT
1µF
1µF
The die attachment area of the G916’s lead frame is
connected to pin 2, which is the GND pin. Therefore,
the GND pin of G916 can carry away the heat of the
G916 die very effectively. To improve the maximum
power providing capability, connect the GND pin to
ground using a large ground plane near the GND pin.
GND
Applications Information
Figure 2. Adjustable Output Using External
Feedback Resistors
Capacitor Selection and Regulator Stability
Normally, use a 1µF capacitor on the input and a 1µF
capacitor on the output of the G916. Larger input ca-
pacitor values and lower ESR provide better sup-
ply-noise rejection and transient response. A higher-
value input capacitor (10µF) may be necessary if large,
fast transients are anticipated and the device is lo-
cated several inches from the power source.
Over Current Protection
The G916 uses a current sense-resistor to monitor the
output current. A portion of the PMOS output transis-
tor’s current is mirrored to a resistor such that the
voltage across this resistor is proportional to the output
current. Once the output current exceeds limit thresh-
old, G916 would be protected with a limited output
current. Further more, when the output is short to
ground, the output current would be folded-back to a
less limit.
Power-Supply Rejection and Operation from
Sources Other than Batteries
The G916 is designed to deliver low dropout voltages
and low quiescent currents in battery powered sys-
tems. Power-supply rejection is 65dB at low frequen-
cies. As the frequency increases above 20kHz, the
output capacitor is the major contributor to the rejec-
tion of power-supply noise.
Over Temperature Protection
To prevent abnormal temperature from occurring, the
G916 has a built-in temperature monitoring circuit.
When it detects the temperature is above 145°C, the
output transistor is turned off. When the IC is cooled
down to below 120°C, the output is turned on again. In
this way, the G916 will be protected against abnormal
junction temperature during operation.
When operating from sources other than batteries,
improve supply-noise rejection and transient response
by increasing the values of the input and output ca-
pacitors, and using passive filtering techniques.
Shutdown Mode
Load Transient Considerations
When the SHDN pin is connected a logic low voltage,
the G916 enters shutdown mode. All the analog cir-
cuits are turned off completely, which reduces the
current consumption to only the leakage current. The
G916 output pass transistor would get into high im-
pedance level. There is an internal discharge path to
help to shorten discharge delay time.
The G916 load-transient response graphs show two
components of the output response: a DC shift of the
output voltage due to the different load currents, and
the transient response. Typical overshoot for step
changes in the load current from 10mA to 300mA is
8mV. Increasing the output capacitor's value and de-
creasing its ESR attenuates transient spikes.
Operating Region and Power Dissipation
Input-Output (Dropout) Voltage
Since the G916 is a linear regulator, its power dissipa-
tion is always given by P = IOUT (VIN – VOUT). The
maximum power dissipation is given by:
A regulator's minimum input-output voltage differential
(or dropout voltage) determines the lowest usable sup-
ply voltage. In battery-powered systems, this will de-
termine the useful end-of-life battery voltage. Because
the G916 use a P-channel MOSFET pass transistor,
their dropout voltage is a function of RDS(ON) multiplied
by the load current.
PD(MAX) = (TJ–TA) /θJA,=(150°C-25°C)/240°C/W = 520mW
Where (TJ–TA) is the temperature difference the G916
die and the ambient air,θJA, is the thermal resistance
of the chosen package to the ambient air. For surface
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
10
Global Mixed-mode Technology Inc.
G916
Layout Guide
The output capacitor also must be located a distance
of not more than 1cm from output to a clean analog
ground. Because it can filter out the output spike
caused by the surge current due to the inductive effect
of the package pin and the printed circuit board’s rout-
ing wire. Figure 5 is adjustable mode of G916 PCB
layout.
An input capacitance of ≅ 1µF is required between the
G916 input pin and ground (the amount of the capaci-
tance may be increased without limit), This capacitor
must be located a distance of not more than 1cm from
the input and return to a clean analog ground.
Input capacitor can filter out the input voltage spike
caused by the surge current due to the inductive effect
of the package pin and the printed circuit board’s rout-
ing wire. Otherwise, the actual voltage at the IN pin
may exceed the absolute maximum rating.
Safe Operating Area of IOUT=150mA
Safe Operating Area of IOUT=300mA
[Power Dissipation Limit]
[Power Dissipation Limit]
250
400
Still air
1oz copper on SOT-23-5 package
Mounted on recommended foorprint (RθJA=240°C/W)
350
300
250
200
150
100
50
TA = 55°C
200
TA = 85°C
TA = 25°C
TA = 25°C
TA = 55°C
150
100
TA = 85°C
Still Air
50
0
1oz copper on SOT-23-5 Package
Mounted on recommended foorprint (RθJA=240°C/W)
0
0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3
Input-Output Voltage Differential VIN-VOUT (V)
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2
Input-Output Voltage Differential VIN-VOUT (V)
Note: VIN(max) <= 5.5V
Note: VIN (max) <= 5.5V
Figure 3a. Safe Operating Area (IOUT=150mA)
Figure 3b. Safe Operating Area (IOUT=300mA)
Maximum Power Dissipation of SOT-23-5
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Still air
1oz copper on SOT-23-5 package
Mounted on recommended foorprint (RθJA=240°C/W)
25
35
45
55
65
75
85
95 105 115 125
*Distance between pin & capacitor must no more than 1cm
Amibent Temperature TA (°C)
Figure 5. Adjustable Mode
Figure 4. Power Dissipation vs. Ambient Temperature
Recommend Minimum Footprint
TSOT-23-5、SOT-23-5
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
11
Global Mixed-mode Technology Inc.
Package Information
G916
C
D
L
H
E
θ1
e1
e
A
A2
A1
b
TSOT-23-5 Package
Note:
1. Package body sizes exclude mold flash protrusions or gate burrs
2. Tolerance ±0.1000 mm (4mil) unless otherwise specified
3. Coplanarity: 0.1000mm
4. Dimension L is measured in gage plane
DIMENSION IN MM
SYMBOL
DIMENSION IN INCH
MIN.
-----
0.00
-----
0.35
0.10
2.70
1.40
-----
-----
2.60
0.37
1°
NOM.
-----
MAX.
1.00
0.10
0.90
0.50
0.25
3.10
1.80
-----
MIN.
-----
NOM.
-----
MAX.
0.039
0.004
0.035
0.020
0.010
0.122
0.071
-----
A
A1
A2
b
-----
0.000
-----
-----
-----
-----
0.40
0.014
0.004
0.106
0.055
-----
0.016
0.006
0.114
0.063
0.075(TYP)
0.037
0.110
-----
C
0.15
D
2.90
E
1.60
e
1.90(TYP)
0.95
e1
H
-----
-----
-----
2.80
3.00
-----
0.102
0.015
1°
0.118
-----
L
------
5°
θ1
9°
5°
9°
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
12
Global Mixed-mode Technology Inc.
G916
C
D
L
H
E
θ1
e1
e
A
A2
A1
b
SOT-23-5 Package
Note:
1. Package body sizes exclude mold flash protrusions or gate burrs
2. Tolerance ±0.1000 mm (4mil) unless otherwise specified
3. Coplanarity: 0.1000mm
4. Dimension L is measured in gage plane
DIMENSION IN MM
SYMBOL
DIMENSION IN INCH
MIN.
1.00
0.00
0.70
0.35
0.10
2.70
1.40
-----
NOM.
1.10
MAX.
1.30
0.10
0.90
0.50
0.25
3.10
1.80
-----
MIN.
0.039
0.000
0.028
0.014
0.004
0.106
0.055
-----
NOM.
0.043
-----
MAX.
0.051
0.004
0.035
0.020
0.010
0.122
0.071
-----
A
A1
A2
b
-----
0.80
0.031
0.016
0.006
0.114
0.063
0.075(TYP)
0.037
0.110
-----
0.40
C
0.15
D
2.90
E
1.60
e
1.90(TYP)
0.95
e1
H
-----
-----
-----
-----
2.60
0.37
1°
2.80
3.00
-----
0.102
0.015
1°
0.118
-----
L
------
θ1
5°
9°
5°
9°
Taping Specification
PACKAGE
TSOT-23-5
SOT-23-5
Q’TY/REEL
3,000 ea
3,000 ea
Feed Direction
TSOT-23-5、SOT-23-5 Package Orientation
GMT Inc. does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and GMT Inc. reserves the right at any time without notice to change said circuitry and specifications.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.7
Jan 25, 2006
13
相关型号:
©2020 ICPDF网 联系我们和版权申明