GLS85LS1016P-S-I-1S-ED101 [GREENLIANT]
Industrial Grade SATA NANDrive;
| 型号： | GLS85LS1016P-S-I-1S-ED101 |
| 厂家： | 
Greenliant |
| 描述： | Industrial Grade SATA NANDrive |
| 文件： | 总7页 (文件大小：133K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
Features
• Industry Standard Serial ATA (SATA) Host
• Integrated Voltage Detector
Detects supply voltage fluctuations and
generates reset during power-up and power-
down to prevent inadvertent writes
• Supports SMART Commands
Interface
-
1)
-
-
-
SATA 1.5Gb/s
ATA/ATAPI-8 compliant
Supports 48-bit address feature set
• 20-Byte Serial Number
• Performance
-
-
Factory pre-programmed 10-Byte unique ID
User-programmable 10-Byte ID
-
Sequential data read -
Up to 120 MByte/sec*
-
Sequential data write -
Up to 80 MByte/sec*
* measured using 128 KByte transfer size
• Robust Built-in ECC
• NAND Configuration
-
1 bit per cell (SLC)
• Industrial Temperature Range
-40°C to 85°C
• FBGA package
14.0 mm x 24.0 mm x 1.95 mm, 145-ball,
1.0 mm ball pitch, FZJE
• Power Management
-
-
-
3.3V and 1.2Vpower supply
Host SATA interface power management
Immediate disabling of unused circuitry
-
-
without host intervention
2)
• Power Specifications
• All Devices are RoHS Compliant
-
Active mode:
855mW typical (GLS85LS1032P)
590mW typical (GLS85LS1016P)
1) Current product revision supports SATA Revision 1.x with
host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5Gb/s).
2) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
-
-
Idle Standby mode:
Sleep mode:
210mW typical
70mW typical
Product Description
The GLS85LS1016P / 1032P Industrial Grade SATA
NANDrive™ devices (referred to as “SATA NANDrive”
in this factsheet) are fully integrated solid state drives.
They combine an advanced Greenliant NAND
controller and 16 or 32 GByte of NAND flash in a
multi-chip package. These products are ideal for
embedded and portable applications that require
smaller form-factor and more reliable data storage.
The integrated NAND flash controller with built-in
advanced
NAND
management
firmware
communicates with the host through the standard
SATA protocol. It does not require any additional or
proprietary software such as the Flash File System
(FFS) and Memory Technology Driver (MTD).
SATA NANDrive is pre-programmed with a 10-Byte
unique serial ID and has the option of programming
an additional 10-Byte serial ID for even greater
system security.
SATA-interface solid state mass storage technology is
widely used in portable and industrial computers, set-
top boxes, multi-functional printers, point-of-sales
terminals, video and audio recorders, medical
instruments and car infotainment systems.
SATA NANDrive’s advanced NAND management
technology enhances data reliability and security,
improves endurance and accurately estimates the
remaining life of the NAND flash devices. This
innovative technology combines robust NAND
controller hardware error correction capabilities with
advanced wear-leveling algorithms and bad block
management to significantly extend the life of the
product.
SATA NANDrive is a single device, solid state drive
(SSD) that provides the functionality and compatibility
of a complete SATA hard disk drive (HDD) in a 14 mm
x 24 mm BGA package for easy, space saving
mounting to a system motherboard. These products
surpass traditional storage in their small size, security,
reliability, ruggedness and low power consumption.
SATA NANDrive devices are offered in a 145-ball
BGA, 1 mm ball pitch package.
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
1
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
1.0
GENERAL DESCRIPTION
Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete
NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram.
1.1.4 Embedded Flash File System
1.1
Optimized SATA NANDrive
The embedded flash file system is an integral part of
SATA NANDrive. It contains MCU firmware that
performs the following tasks:
The heart of SATA NANDrive is the SATA NAND flash
memory controller which translates standard SATA
signals into flash media data and control signals. The
following components contribute to SATA NANDrive’s
operation.
1. Translates host side signals into flash media
writes and reads
1.1.1 Microcontroller Unit (MCU)
2. Provides flash media wear leveling to spread the
flash writes across all memory address space to
increase the longevity of flash media
The MCU translates SATA commands into data and
control signals required for flash media operation.
3. Keeps track of data file structures
1.1.2 Internal Direct Memory Access (DMA)
4. Manages system security for the selected
protection zones
SATA NANDrive uses internal DMA allowing instant
data transfer from/to buffer to/from flash media. This
implementation eliminates microcontroller overhead
associated with the traditional, firmware-based
approach, thereby increasing the data transfer rate.
1.1.5 Error Correction Code (ECC)
High performance is achieved through optimized
hardware error detection and correction.
1.1.3 Power Management Unit (PMU)
1.1.6 Serial Communication Interface (SCI)
The PMU controls the power consumption of SATA
NANDrive. The PMU dramatically reduces the power
consumption of SATA NANDrive by putting the part of
The Serial Communication Interface (SCI) is designed
for error reporting. During the product development
stage, it is recommended to provide the SCI port on
the PCB to aid in design validation.
3)
the circuitry that is not in operation into sleep mode.
1.1.7 Multi-tasking Interface
The Flash File System handles inadvertent power
interrupts and has auto-recovery capability to ensure
SATA NANDrive firmware integrity. For regular power
The multi-tasking interface enables fast, sequential
write performance by allowing concurrent Read,
Program and Erase operations to multiple flash media.
management,
the
host
must
send
a
STANDBY_IMMEDIATE (E0h), IDLE_IMMEDIATE
(E1h), STANDBY (E2h) or IDLE (E3h) command and
wait for command ready before powering down SATA
NANDrive.
1.2
SMT Reflow Consideration
The SATA NANDrive family utilizes standard NAND
flash for data storage. Because the high temperature
in a surface-mount soldering reflow process may alter
the content on NAND flash, it is recommended to
program SATA NANDrive after the reflow process.
3) For management of the Sleep Mode, refer to “SATA
NANDrive Application Design Guide.”
1.3
Advanced NAND Management
SATA NANDrive’s integrated controller uses
advanced wear-leveling algorithms to substantially
increase the longevity of NAND flash media. Wear
caused by data writes is evenly distributed in all or
select blocks in the device that prevents “hot spots” in
locations that are programmed and erased extensively.
This effective wear-leveling technique results in
optimized device endurance, enhanced data retention
and higher reliability required by long-life applications.
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
2
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
2.0
FUNCTIONAL BLOCKS
SATA NANDrive
MCU
NAND Controller
Embedded Flash
File System
SATA ll
HOST I/F
3.0/1.5 Gbps
SRAM Buffer
Flash Media I/F
NAND I/F
ECC
ECC
NAND
Flash
Internal
DMA
PMU
SCI
Figure 2-1: SATA NANDrive Block Diagram
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
3
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
3.0
P R ODUC T OR DE R ING INFOR MATION
GLS 85 LS 1 0xxP - S - I - FZJE - NDxxx
XX XX X XXXX - X - X - XXXX - XXXXX
Ordering Code 4)
NDxxx or TTxxx = NANDrive revision
Exxxx = Evaluation Board revision
Environmental Attribute
E = non-Pb solder (RoHS Compliant)
Package Modifier
ZJ = 145-ball positions
Package Type
F = FBGA
Operation Temperature
I = Industrial: -40°C to +85°C
NAND Configuration
S = 1 bit per cell
Generation / Product Configuration
P = First generation
Capacity
016 = 16 GByte
032 = 32 GByte
MByte or GByte Designator
0 = MByte
1 = GByte
Interface
S = SATA
Voltage
L = 3.3V
Product Series
85 = NANDrive
4) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a special C-SPEC
(custom specification) which is required by the end-customer to be marked on the device.
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
4
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
Valid Combinations
Valid product combinations are those that are in the mass production or will be in the mass production. Consult
your Greenliant sales representative to confirm availability of the valid combinations and to determine availability
of new product combinations.
Table 3-1: SATA NANDrive Product Valid Ordering Numbers
Capacity Operating Temperature
Part Number
Package
16GB
16GB
16GB
32GB
32GB
32GB
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-FZJE-ND101
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-FZJE-ND104
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-FZJE-TT095
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-FZJE-ND101
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-FZJE-ND104
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-FZJE-TT095
FZJE, 14x24x1.95mm
FZJE, 14x24x1.95mm
FZJE, 14x24x1.95mm
FZJE, 14x24x1.95mm
FZJE, 14x24x1.95mm
FZJE, 14x24x1.95mm
*
TT095 products include enhanced support for TRIM command and power management in Windows environments.
Table 3-2: SATA NANDrive Evaluation Board Valid Ordering Numbers
Capacity Operating Temperature Part Number
Form Factor
16GB
16GB
16GB
32GB
32GB
32GB
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-1S-ED101
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-1S-ED104
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-1S-ET095
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-1S-ED101
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-1S-ED104
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-1S- ET095
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Module with SATA connector
Table 3-3: SATA NANDrive miniSATA Evaluation Board Valid Ordering Numbers
Capacity Operating Temperature
Part Number
Form Factor
16GB
16GB
32GB
32GB
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-1MS-ED101
Industrial (-40°C to 85°C) GLS85LS1016P-S-I-1MS-ED104
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-1MS-ED101
Industrial (-40°C to 85°C) GLS85LS1032P-S-I-1MS-ED104
JEDEC MO-300
JEDEC MO-300
JEDEC MO-300
JEDEC MO-300
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
5
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
3.1
Package Diagram
TOP VIEW
11
10
9
8
7
6
5
4
3
2
1
14.0
+/- 0.1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA AB AC
24.0 ±0.1
A1
CORNER
BOTTOM VIEW
0.5 +/- 0.05
(145x)
14.0
3.0
1
2
3
4
5
6
1.0
8.0
7
8
9
10
11
1.0
E
A
B
C
D
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA AB AC
SIDE
VIEW
1mm
DETAIL
Note: All linear dimensions are in millimeters.
Untoleranced dimensions are nominal target values.
Coplanarity: 0.15mm.
0.40 ±0.05
Ball opening size is 0.40mm (± 0.05mm).
1.80 ± 0.15
0.15
SEATING PLANE
Figure 3-1: SATA NANDrive 145-Ball, Ball Grid Array (BGA) Greenliant Package Code: FZJ
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
6
GLS85LS1016P / 1032P
Industrial Grade SATA NANDrive™
Factsheet 02.100
July 2018
Revision History
Revision
01.000
01.001
01.002
Description
Date
Initial release of Factsheet for GLS85LS1016P/1032P
Placed Valid Combinations into table format in Section 4.0
Removed Pin Assignments and Updated section numbering
Updated Power Specifications on first page
January 18, 2013
February 25, 2013
August 29, 2013
01.100
Added information for part numbers GLS85LS1016P-S-I-FZJE-ND104
and GLS85LS1032P-S-I-FZJE-ND104
November 21, 2013
02.000
02.100
Added GLS85LS1016P/1032P part numbers with the TT095 suffix
Added Evaluation Board part numbers with the ET095 suffix
October 19, 2016
July 10, 2018
© 2018 Greenliant. All rights reserved.
Greenliant and the Greenliant logo are registered trademarks, and NANDrive is a trademark of Greenliant. All
other trademarks and registered trademarks are the property of their respective owners.
Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable
capacity may be less.
Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant
Terms and Conditions of Sale.
www.greenliant.com
These specifications are subject to change without notice.
© 2018 Greenliant
07/10/2018
S71445-F
7
相关型号：
©2020 ICPDF网 联系我们和版权申明