GLS85VM1004Q-S-I-E2-ED218 [GREENLIANT]
Industrial Grade eMMC NANDrive EX Series;型号: | GLS85VM1004Q-S-I-E2-ED218 |
厂家: | Greenliant |
描述: | Industrial Grade eMMC NANDrive EX Series |
文件: | 总7页 (文件大小:167K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
Features
• Industry Standard Embedded MultiMediaCard
• Integrated Voltage Detector
Detects supply voltage fluctuations and
(eMMC) Host Interface
–
–
–
JEDEC/MMC Standard Version 5.1
JESD84-B51 compliant
Backward compatible with previous eMMC
standards
generates reset during power-up and power-
down to prevent inadvertent writes
• Expanded Data Protection
–
Hardware Write Protection pin
• Performance
–
Data sanitization
–
–
–
–
–
–
eMMC clock speed: Up to 200MHz
eMMC data bus width: x1/x4/x8
Supports Dual Data Rate mode
Supports HS200 / HS400 modes
Sequential data read: Up to 160 MByte/sec*
Sequential data write: Up to 57 MByte/sec*
* measured in HS400 enhanced mode using 1 MByte
transfer size
• Latency Management
Reduces latency due to background tasks
during time critical read/write operations
• Supports SMART and TRIM Commands
• Robust Built-in ECC
–
• NAND Configuration
–
1 bit per cell (SLC)
–
Designed with Greenliant’s advanced
EnduroSLC™ Technology
• Power Management
–
–
–
3.3V power supply (VCC)
3.3V or 1.8V eMMC IO voltage (VCCQ
Immediate disabling of unused circuitry
without host intervention
• High Endurance
)
–
GLS85VM1004G: 50K P/E cycles
–
GLS85VM1004Q: 100K P/E cycles
• Operating Temperature Range
Industrial: -40°C to 85°C
• 100-ball LBGA Package
14.0 mm x 18.0 mm x 1.40 mm,
1.0 mm ball pitch, LFWE
• Power Specifications
–
–
Active mode: 471 mW (typical)
–
Sleep mode: 2.15mW (typical)
–
• All Devices are RoHS Compliant
Product Description
The GLS85VM1004G / 1004Q eMMC NANDrive™ EX
Series devices (referred to as “eMMC NANDrive” in
this factsheet) are fully integrated solid state drives.
They combine an advanced Greenliant NAND
controller and 4 GBytes of NAND flash memory in a
multi-chip package. These products are ideal for
embedded and portable applications that require small
form factor, high endurance and reliable data storage.
The integrated NAND flash controller with built-in
advanced NAND management firmware communicates
with the host through the standard eMMC protocol. It
does not require any additional or proprietary software
such as the Flash File System (FFS) and Memory
Technology Driver (MTD).
eMMC NANDrive’s advanced NAND management
technology enhances data security, improves
endurance and accurately tracks the usage of the
NAND flash. This innovative technology combines
robust error correction capabilities with advanced
wear-leveling algorithms and bad block management
to extend the life of the product.
eMMC solid state drives are widely used in GPS and
telematics, in-vehicle infotainment, portable and
industrial computers, handheld data collection
scanners, point-of-sale terminals, networking and
telecommunications equipment, robotics, audio and
video recorders, monitoring devices and set-top boxes.
eMMC NANDrive supports Single Data Rate (SDR)
and Dual Data Rate (DDR) modes, HS200 mode,
HS400 mode, boot, multiple partitions, permanent and
partial write protect, Replay Protected Memory Block
(RPMB) access, Sanitize and TRIM, hardware reset
and other features detailed in the eMMC 5.1 standard
specification. It is backward compatible with previous
eMMC standards
eMMC NANDrive provides complete eMMC solid state
drive (SSD) functionality and compatibility in a 14mm
x 18mm BGA package for easy, space saving
mounting to a system motherboard. With its small size,
low power consumption, strong security, reliability and
ruggedness, eMMC NANDrive surpasses removable
storage and discrete NAND-based products.
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
1
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
1.0 GENERAL DESCRIPTION
Each eMMC NANDrive contains an integrated eMMC NAND flash memory controller and NAND flash die in a
BGA package. Refer to Figure 2-1 for the eMMC NANDrive block diagram.
1.1.5 Error Correction Code (ECC)
1.1 Optimized eMMC NANDrive
The ECC technology uses advanced algorithms to
detect and correct errors, ensuring data integrity and
extending the SSD lifespan.
The heart of the eMMC NANDrive is the eMMC NAND
flash memory controller, which translates standard
eMMC signals into flash media data and control
signals. The following components contribute to the
eMMC NANDrive’s operation.
1.1.6 Serial Communication Interface (SCI)
The Serial Communication Interface (SCI) is designed
for error reporting. During the product development
stage, it is recommended to provide the SCI port on
the PCB to aid in design validation.
1.1.1 Microcontroller Unit (MCU)
The MCU transfers the eMMC commands into data
and control signals required for flash media operation.
1.1.7 Multi-tasking Interface
1.1.2 Internal Direct Memory Access (DMA)
The multi-tasking interface enables fast, sequential
write performance by allowing concurrent Read,
Program and Erase operations to multiple flash media.
The eMMC NANDrive uses internal DMA allowing
instant data transfer from/to buffer to/from flash media.
This implementation eliminates microcontroller
overhead associated with the traditional, firmware-
based approach, thereby increasing the data transfer
rate.
1.2 SMT Reflow Consideration
Preprogrammed NAND devices have temperature
limits due to data retention. The EnduroSLC™ eMMC
NANDrive family uses high-grade SLC NAND flash,
which can retain data in high temperature
environments. Using Greenliant’s recommended
reflow profile during production will help prevent
damage to the device and ensure better retention of
any preprogrammed data through the surface-mount
soldering process. See the relevant datasheet section
describing the recommended reflow temperature limits.
1.1.3 Power Management Unit (PMU)
The PMU controls the power consumption of the
eMMC NANDrive. The PMU dramatically reduces the
power consumption of the eMMC NANDrive by putting
the part of the circuitry that is not in operation into
Sleep mode.
The Flash File System handles inadvertent power
interrupts and has auto-recovery capability to ensure
the eMMC NANDrive’s data integrity.
1.3 Advanced NAND Management
1.1.4 Embedded Flash File System
eMMC NANDrive’s integrated controller uses
advanced wear-leveling algorithms to substantially
increase the longevity of NAND flash media. Wear
caused by data writes is evenly distributed in all or
select blocks in the device that prevents “hot spots” in
locations that are programmed and erased extensively.
This effective wear-leveling technique results in
optimized device endurance, enhanced data retention
and higher reliability required by long-life applications.
The embedded flash file system is an integral part of
the eMMC NANDrive. It contains MCU firmware that
performs the following tasks:
1. Translates host side signals into flash media
writes and reads
2. Provides flash media wear leveling to spread
flash writes across all memory address space to
increase the longevity of flash media
3. Keeps track of the data file structure
4. Manages system security for the selected
protection zones
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
2
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
2.0 FUNCTIONAL BLOCKS
eMMC NANDrive
Embedded Flash
File System
I/F
eMMC
HOST I/F
NAND
Flash
Figure 2-1: eMMC NANDrive Block Diagram
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
3
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
3.0 Product Ordering Information
GLS 85 VM 1 0xx x - S - I - LFWE - NDxxx
XX XX X XXX X - X - X - XXXX - XXXXX
Ordering Code 1)
NDxxx = NANDrive Revision
EDxxx = Evaluation Board Revision
Environmental Attribute
E = non-Pb solder (RoHS Compliant)
Package Modifier
W = 100-ball positions
Package Type
LF = LBGA (max. package height 1.40mm)
Operating Temperature
I = Industrial: -40°C to +85°C
NAND Configuration
S = 1 bit per cell
Product Generation
G, Q = Generation
Capacity
004 = 4 GByte
MByte or GByte Designator
0 = MByte
1 = GByte
Interface
M = eMMC
Voltage
V = 2.7V to 3.3V
Product Family
85 = NANDrive
1) Note that the top side marking on the package typically does not include ordering codes (e.g. NDxxx), unless it is a
special custom specification (C-SPEC) required by the end-customer to be marked on the device.
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
4
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
Valid Combinations
Valid product combinations are those that are in mass production or will be in the mass production. Consult your
Greenliant sales representative to confirm availability of the valid combinations and to determine availability of
new product combinations.
Table 3-1: eMMC NANDrive Product Valid Ordering Numbers
Capacity Operating Temperature
Part Number
Package
4GB
4GB
Industrial (-40°C to 85°C) GLS85VM1004G-S-I-LFWE-ND217
Industrial (-40°C to 85°C) GLS85VM1004Q-S-I-LFWE-ND218
LFWE, 14x18x1.40mm
LFWE, 14x18x1.40mm
Table 3-2: eMMC Evaluation Board Valid Ordering Numbers
Capacity Operating Temperature Part Number
Form Factor 2)
JEDEC MO-277
JEDEC MO-277
4GB
4GB
Industrial (-40°C to 85°C) GLS85VM1004G-S-I-E2-ED217
Industrial (-40°C to 85°C) GLS85VM1004Q-S-I-E2-ED218
2) The evaluation boards with the form factor MO-277 support up to 52MHz with x1/x4/x8 bus and Dual Data Rate
mode. Use them for comprehensive functional testing. If the end-user’s system has support for 200MHz bus speed,
it can be tested only with eMMC 5.1 NANDrive devices soldered down on the user’s board.
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
5
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
4.0 Package Diagram
GLS85VM1004G / 1004Q-S-I-LFWE
0.10
Note:
All linear dimensions are in millimeters.
Untoleranced dimensions are nominal target values.
Coplanarity: 0.10 mm
Ball diameter is 0.45 mm (± 0.05 mm)
Ball opening size is 0.38 mm (± 0.05 mm), SMD type
Figure 4-1: eMMC NANDrive 100-Ball, Ball Grid Array (BGA) Greenliant Package Code: LFWE
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
6
GLS FS0019 Rev. 00
GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
Revision History
Number
01.000
01.001
01.100
01.200
Description
Date
January 28, 2019
April 30, 2019
October 14, 2019
March 12, 2020
Initial release as Factsheet
Added Endurance on page 1
Updated Features on page 1 and section 1.1.5
Updated Features on page 1
© 2020 Greenliant. All rights reserved.
Greenliant and the Greenliant logo are registered trademarks, and EnduroSLC and NANDrive are trademarks of
Greenliant. All other trademarks and registered trademarks are the property of their respective owners.
Specifications are subject to change without notice. Memory sizes denote raw storage capacity; actual usable
capacity may be less.
Greenliant makes no warranty for the use of its products other than those expressly contained in the Greenliant
Terms and Conditions of Sale.
www.greenliant.com
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
7
GLS FS0019 Rev. 00
相关型号:
©2020 ICPDF网 联系我们和版权申明